Search Results (62)

Poly(ethylene terephthalate) (PET) is a widely used commodity polymer owing to its low cost, excellent mechanical properties, and high processability. Chemical modification of PET surfaces to impart specific functionalities represents an effective strategy for transforming PET into high-value-added materials without altering its bulk properties. In this study, we investigated the surface functionalization of PET substrates using surface-initiated atom transfer radical polymerization (SI-ATRP). ATRP initiation sites were introduced onto PET surfaces through mild surface hydrolysis followed by polyethyleneimine coating. To further enhance the grafting density, an inimer-based strategy was employed, in which a bifunctional monomer containing both a polymerizable group and a latent initiation site was used to form hyperbranched polymer structures on the PET surface, thereby amplifying the number of active initiation sites. Using these modified PET substrates, SI-ATRP of functional methacrylate monomers was successfully carried out. Grafting of poly(2,2,2-trifluoroethyl methacrylate) imparted highly hydrophobic surface properties, yielding water contact angles above 120°, whereas grafting of poly([2-(methacryloyloxy)ethyl]trimethylammonium chloride) produced hydrophilic surfaces with contact angles below 20°. Surface characterization by X-ray photoelectron spectroscopy confirmed successful graft polymerization and effective surface coverage. While the macroscopic wettability was primarily governed by the chemical nature of the grafted polymers, the inimer-based initiation-site amplification significantly enhanced the surface electrostatic properties of the polycationic polymer–grafted surfaces, increasing the ζ-potential from approximately +20 mV to over +100 mV. Antibacterial tests using Escherichia coli K-12 as a model bacterium demonstrated that PET substrates grafted with poly([2-(methacryloyloxy)ethyl]trimethylammonium chloride) exhibited clear contact-active antibacterial activity, achieving up to 2-log reduction in viable bacterial counts after 3 h of contact incubation. These results highlight the importance of molecular-level control of grafting architecture and surface electrostatic properties in the design of functional antibacterial PET surfaces. Full article

It is widely recognized that fine surface structures found in nature contribute to surface functionality, and studies on the design of functional materials based on biomimetics have been actively conducted. In this study, polymer thin films with hierarchically ordered surface structure were prepared by combining both nanoimprinting using anodically oxidized porous alumina (AAO) as a template and surface-initiated atom transfer radical polymerization (SI-ATRP). To prepare such polymer films, we designed a new copolymer (poly{[2-(4-methyl-2-oxo-2H-chromen-7-yloxy)ethyl methacrylate]-co-[2-(2-bromo-2-methylpropionyloxy)ethyl methacrylate]}; poly(MCMA-co-HEMABr)) with coumarin moieties and α-haloester moieties in the pendants. The MCMA repeating units function to fix the pillar structure by photodimerization, and the HEMABr ones act as the polymerization initiation sites for SI-ATRP on the pillar surfaces. Surface structures consisting of vertically oriented multiple pillars were fabricated on the spin-coated poly(MCMA-co-HEMABr) thin films by nanoimprinting using an AAO template. Then, the coumarin moieties inside each pillar were crosslinked by UV light irradiation to fix the pillar structure. SEM observation confirmed that the internally crosslinked pillar structures were maintained even when immersed in organic solvents such as 1,2-dichloroethane and anisole, which are employed as solvents under SI-ATRP conditions. Finally, poly(2,2,2-trifluoroethyl methacrylate) and poly(N-isopropylacrylamide) chains were grafted onto the thin film by SI-ATRP, respectively, to prepare the hierarchically ordered surface structure. Furthermore, in this study, the surface properties as well as the thermoresponsive hydrophilic/hydrophobic switching of the obtained polymer films were investigated. The surface morphology and chemistry of the films with and without pillar structures were compared, especially the interfacial properties expressed as wettability. Grafting poly(TFEMA) increased the static contact angle for both flat and pillar films, and the con-tact angle of the pillar film surface increased from 104° for the flat film sample to 112°, suggesting the contribution of the pillar structure. Meanwhile, the pillar film surface grafted with poly(NIPAM) brought about a significant change in wettability when changing the temperature between 22 °C and 38 °C. Full article

Stimuli-responsive polymers (SRPs) have garnered significant attention in recent decades due to their immense potential in biomedical and environmental applications. When these SRPs are grafted onto magnetic nanoparticles, they form multifunctional nanocomposites capable of various complex applications, such as targeted drug delivery, advanced separations, and magnetic resonance imaging. In this study, we employed a one-step hydrothermal method using 3-aminopropyltrimethoxysilane (APTES) to synthesize APTES-modified Fe₃O₄ nanoparticles (APTES@Fe₃O₄) featuring reactive terminal amine groups. Subsequently, via two consecutive surface-initiated atom transfer radical polymerizations (SI-ATRP), pH- and temperature-responsive polymer blocks were grown from the Fe₃O₄ surface, resulting in the formation of poly(itaconic acid)-block-poly(N-isopropyl acrylamide) (PIA-b-PNIPAM)-grafted nanomagnetic particles (PIA-b-PNIPAM@Fe₃O₄). To confirm the chemical composition and assess how the particle morphology and size distribution of these SRP-based nanocomposites change in response to ambient pH and temperature stimuli, various characterization techniques were employed, including transmission electron microscopy, differential light scattering, and Fourier transform infrared spectroscopy. The results indicated successful synthesis, with PIA-b-PNIPAM@Fe₃O₄ demonstrating sensitivity to both temperature and pH. Full article

Polymer brushes (PBs) are transformative surface-modifying nanostructures, yet their synthesis via controlled methods like copper-mediated surface-initiated atom-transfer radical polymerization (Cu⁰-SI-ATRP) faces reproducibility challenges due to a lack of understanding of parameter interdependencies. This study systematically evaluates the Cu⁰-SI-ATRP process for polyacrylamide brushes (PAM-PBs), aiming to clarify key parameters that influence the synthesis process. This evaluation followed a step-by-step characterization that tracked molecular changes through infrared spectroscopy (IR) and surface development by contact angle (CA) through two different mixing methods: ultrasonic mixing and process simplification (Method A) and following literature-based parameters (Method B). Both methods, consisting of surface activation, 3-aminopropyltriethoxysilane (APTES) deposition, bromoisobutyryl bromide (BiBB) anchoring, and polymerization, were analyzed by varying parameters like concentration, temperature, and time. Results showed ultrasonication during surface activation enhanced siloxane (1139→1115 cm⁻¹) and amine (1531 cm⁻¹) group availability while reducing APTES concentration to 1 Vol% without drying sufficed for BiBB anchoring. BiBB exhibited insensitivity to concentration but benefited from premixing, evidenced by sharp C–Br (~1170 cm⁻¹) and methyl (3000–2800 cm⁻¹) bands. Additionally, it was observed that PAM-PBs improved with Method A, which had reduced variance in polymer fingerprint regions compared to Method B. Adding to the above, CA measurements gave complementary step-by-step information along the modifications of the surface, revealing distinct wettability behaviors between bulk PAM and synthesized PAM-PBs (from 51° to 37°). As such, this work identifies key parameter influence (e.g., mixing, BiBB concentration), simplifies steps (drying omission, lower APTES concentration), and demonstrates a step-by-step, systematic parameter decoupling that reduces variability. In essence, this detailed parameter analysis addresses the PAM-PBs synthesis process with better reproducibility than the previously reported synthesis method and achieves the identification of characteristic behaviors across the step-by-step process without the imperative need for higher-cost characterizations. Full article

Thread-based analytical devices are low-cost, portable, and easy to use, making them ideal for detecting various biomolecules like glucose and DNA with minimal sample requirements, while also offering environmental benefits through their biodegradability. This study explores the potential of zwitterionic poly(sulfobetaine methacrylate) brushes modified cotton thread (PSBMA@threads) as an innovative substitute for DNA solid-phase extraction. The PSBMA polymer brushes were synthesized on cotton threads via surface-initiated atom transfer radical polymerization (SI-ATRP). The usability of the PSBMA@threads for DNA extraction from cell lysates containing cell debris, proteins, and detergents was evaluated. Characterization using SEM, FTIR, and EDS confirmed the successful functionalization with PSBMA polymer brushes. The antifouling properties of PSBMA@threads, including resistance to non-specific protein adsorption and underwater oil repellency, were assessed. The results demonstrated selective DNA capture from protein and lipid-rich lysates. Optimized extraction parameters improved DNA yield, enabling efficient extraction from tumor cells, which successfully underwent PCR amplification. Comparative experiments with commercial silica membrane-based columns revealed that PSBMA@threads exhibited comparable DNA extraction capability. The PSBMA@threads maintained extraction capability after six months of ambient storage, highlighting its stability and cost-effectiveness for nucleic acid isolation in analytical applications. Full article

This study introduces a novel water-insoluble dispersant for coal water slurry (CWS), namely, a poly(sodium styrene sulfonate)-grafted SiO₂ nanoparticle (SiO₂-g-PSSNa). SiO₂-g-PSSNa was synthesized by combining the surface acylation reaction with surface-initiated atom transfer radical polymerization (SI-ATRP). Fourier transform infrared spectrometry (FTIR), X-ray photoelectron spectroscopy (XPS), energy dispersive spectrometer (EDS), nuclear magnetic resonance spectroscopy (NMR) and thermogravimetric analysis (TGA) verified that SiO₂-g-PSSNa with the desired structure was successfully obtained. Afterwards, the performance of SiO₂-g-PSSNa as a dispersant in CWS preparation was evaluated. The results indicated that the optimal dosage of SiO₂-g-PSSNa was 0.3%. Compared to the famous commercial products, PSSNa and lignosulfonate (LS), SiO₂-g-PSSNa exhibits improved viscosity reduction performance. When SiO₂-g-PSSNa was used as the dispersant, the maximum coal loading of CWS was 64.2%, which was higher than LS (63.4%) and PSSNa (63.9%). All CWSs obtained in this study were pseudoplastic fluids and more consistent with the Herschel–Bulkley rheological model. The turbiscan stability index (TSI) of CWS prepared with SiO₂-g-PSSNa was 0.05, which was significantly lower than CWSs obtained from PSSNa (0.30) and LS (0.36). Therefore, SiO₂-g-PSSNa also exhibits excellent stability performance. This result was confirmed by rod penetration tests. The underlying mechanism was also clarified by various measurements, such as contact angle, zeta potential, EDS and low-field nuclear magnetic resonance spectra (low-field NMR). The results reveal that SiO₂-g-PSSNa can adsorbed onto the coal surface. SiO₂-g-PSSNa possesses a special branched structure, which bears a higher charge density as compared to linear ones with approximate chemical composition. As a result, coal particles adsorbed with SiO₂-g-PSSNa exhibit more electronegativity. With the enhancement of the electrostatic repulsive between coal particles, the apparent viscosity was lowered and the static stability was improved. This study demonstrated that solubility in water is not an essential factor in engineering the dispersant. Densely charged groups are probably more important. Full article

Choline is an important molecule in monitoring food safety and infant nutrition. Here, we report Ce nanogels synthesized by atom transfer radical polymerization (ATRP) employing Ce-coordinated acryloyl-lysine polymer brushes (Ce@SiO₂ NGs) as highly efficient cascade nanozymes for colorimetric detection of choline. The synthesized Ce@SiO₂ NGs demonstrated remarkable peroxidase-like activity with a porous exterior, which are essential to entrap choline oxidase (COx) to yield COx@Ce@SiO₂ NGs and construct a cascade reaction system to detect choline. Immobilized COx catalyzed the oxidation of choline in food samples to produce H₂O₂, which subsequently induced the oxidation of chromogenic substrate 3,3′,5,5′-tetramethylbenzidine (TMB) to produce blue color signals. This method enabled the selective and sensitive detection of target choline with a satisfactory linear range of 4–400 μM, which is sufficient to analyze foodborne choline. The practical utility of the COx@Ce@SiO₂ NG-based assay was successfully validated to determine choline spiked in commercially available milk and infant formula with high accuracy and precision values. This approach provides a simple and affordable method of choline detection and has the potential to lead to more developments in ATRP-based nanozymes for diverse biosensing applications. Full article

Background: In recent years, the advancement of computational chemistry has offered new insights into the rational design of molecularly imprinted polymers (MIPs). From this aspect, our study tried to give quantitative parameters for evaluating imprinting efficiency and exploring the formation mechanism of MIPs by combining simulation and experiments. Methods: The pre-polymerization system of sulfadimethoxine (SDM) was investigated using a combination of quantum chemical (QC) calculations and molecular dynamics (MD) simulations. MIPs were prepared on the surface of silica gel by a surface-initiated supplemental activator and reducing agent atom transfer radical polymerization (SI-SARA ATRP). Results: The results of the QC calculations showed that carboxylic monomers exhibited higher bonding energies with template molecules than carboxylic ester monomers. MD simulations confirmed the hydrogen bonding sites predicted by QC calculations. Furthermore, it was observed that only two molecules of monomers could bind up to one molecule of SDM, even when the functional monomer ratio was up to 10. Two quantitative parameters, namely, the effective binding number (EBN) and the maximum hydrogen bond number (HBN_Max), were defined. Higher values of EBN and HBN_Max indicated a higher effective binding efficiency. Hydrogen bond occupancies and RDF analysis were performed to analyze the hydrogen bond formation between the template and the monomer from different perspectives. Furthermore, under the influence of the EBN and collision probability of the template and the monomers, the experimental results show that the optimal molar ratio of template to monomer is 1:3. Conclusions: The method of monomer screening presented in this study can be extended to future investigations of pre-polymerization systems involving different templates and monomers. Full article

A simple strategy was adopted for the preparation of an antimicrobial natural rubber/graphene oxide (NR/GO) composite film modified through the use of zwitterionic polymer brushes. An NR/GO composite film with antibacterial properties was prepared using a water-based solution-casting method. The composited GO was dispersed uniformly in the NR matrix and compensated for mechanical loss in the process of modification. Based on the high bromination activity of α–H in the structure of cis-polyisoprene, the composite films were brominated on the surface through the use of N-bromosuccinimide (NBS) under the irradiation of a 40 W tungsten lamp. Polymerization was carried out on the brominated films using sulfobetaine methacrylate (SBMA) as a monomer via surface-initiated atom transfer radical polymerization (SI-ATRP). The NR/GO composite films modified using polymer brushes (PSBMAs) exhibited 99.99% antimicrobial activity for resistance to Escherichia coli and Staphylococcus aureus. A novel polymer modification strategy for NR composite materials was established effectively, and the enhanced antimicrobial properties expand the application prospects in the medical field. Full article

Contamination of underground water by uranium (U) and other heavy metals is a growing concern. Mesoporous silica nanoparticles (MSNs) have shown great potential as an adsorbent material for heavy metal removal. This study synthesized a novel MSN using surface-initiated atom transfer radical polymerization (SI-ATRP) and evaluated its effectiveness for removing uranium from aqueous solutions under different conditions. The particle size was reduced to 150–240 nm to enhance adsorption. Fourier transform infrared characterization and thermogravimetric analysis confirmed successful synthesis and modification. Results showed that the MSN adsorbent was highly effective in removing U, with a removal rate of 85.35% at 120 min. Temperature had a significant impact, with the highest removal rate of 96.7% achieved at 25 °C and a U concentration of 10 ppm. The highest removal rate of 91.89% was achieved at a pH of 6 and a U concentration of 50 ppm. The highest removal rate of 95.16% was achieved at 25 mg and a U concentration of 50 ppm at room temperature for 60 min. The MSNs also showed a 58.27% removal rate in a mixture solution at room temperature for 60 min. This study demonstrates the effectiveness of the MSN adsorbent for removing U under different conditions. Full article

Although zinc (Zn) is one of the elements with the greatest potential for biodegradable uses, pure Zn does not have the ideal mechanical or degrading properties for orthopaedic applications. The current research aims at studying the microstructure and corrosion behaviour of pure Zn (used as a reference material) and Zn alloyed with 1.89 wt.% magnesium (Mg), both in their extruded states as well as after being coated with polymethyl methacrylate (PMMA). The grafting-from approach was used to create a PMMA covering. The “grafting-from” method entails three steps: the alkali activation of the alloys, their functionalization with an initiator of polymerization through a phosphonate-attaching group, and the surface-initiated atom transfer radical polymerisation (SI-ATRP) to grow PMMA chains. Electrochemical and immersion corrosion tests were carried out in a simulated body fluid (SBF), and both confirmed the enhanced corrosion behaviour obtained after coating. The electrochemical test revealed a decrease in the degradation rate of the alloy from 0.37 ± 0.14 mm/y to 0.22 ± 0.01 mm/y. The immersion test showed the ability of complete protection for 240 h. After 720 h of immersion, the coated alloy displays minute crevice corrosion with very trivial pitting compared to the severe localized (galvanic and pitting) corrosion type that was detected in the bare alloy. Full article

The development of organic memory devices, regarding factors such as structure construction, principle exploration, and material design, has become a powerful supplement to traditional silicon-based information storage. The in-situ growth of materials on substrate surfaces can achieve closer bonding between materials and electrodes. Bio-inspired by mussel chemistry, polydopamine (PDA) was self-assembled on a flexible substrate as a connecting layer, and 2-bromoiso-butyryl bromide (BiBB) was utilized as an initiator for the polymerization of an iridium complex via surface-initiated atom-transfer radical polymerization (SI-ATRP). A device with the structure of Al/PDA-PPy₃Ir/ITO was constructed after the deposition of aluminum. The device exhibited a nonvolatile rewritable memory characteristic with a turn-on voltage of −1.0 V and an ON/OFF current ratio of 6.3 × 10³. In addition, the memory performance of the Al/PDA-PPy₃Ir/ITO device remained stable at bending states due to the intrinsic flexibility of the active layer, which can be expanded into the establishment of flexible memory devices. Spectroscopy and electrochemical characterization suggested that the resistive memory properties of the device stemmed from charge transfer between PDA and iridium polymer in the active layer (PDA-PPy₃Ir) under an applied voltage. Full article

Biofouling on surfaces, caused by the assimilation of proteins, peptides, lipids and microorganisms, leads to contamination, deterioration and failure of biomedical devices and causes implants rejection. To address these issues, various antifouling strategies have been extensively studied, including polyethylene glycol-based polymer brushes. Conducting polymers-based biointerfaces have emerged as advanced surfaces for interfacing biological tissues and organs with electronics. Antifouling of such biointerfaces is a challenge. In this study, we fabricated electrospun fibre mats from sulphonated polystyrene-block-poly(ethylene-ran-butylene)-block-polystyrene (sSEBS), infused with conducting polymer poly(3,4-ethylenedioxythiophene) (PEDOT) (sSEBS-PEDOT), to produce a conductive (2.06 ± 0.1 S/cm), highly porous, fibre mat that can be used as a biointerface in bioelectronic applications. To afford antifouling, here the poly(oligo (ethylene glycol) methyl ether methacrylate) (POEGMA) brushes were grafted onto the sSEBS-PEDOT conducting fibre mats via surface-initiated atom transfer radical polymerization technique (SI-ATRP). For that, a copolymer of EDOT and an EDOT derivative with SI-ATRP initiating sites, 3,4-ethylenedioxythiophene) methyl 2-bromopropanoate (EDOTBr), was firstly electropolymerized on the sSEBS-PEDOT fibre mat to provide sSEBS-PEDOT/P(EDOT-co-EDOTBr). The POEGMA brushes were grafted from the sSEBS-PEDOT/P(EDOT-co-EDOTBr) and the polymerization kinetics confirmed the successful growth of the brushes. Fibre mats with 10-mers and 30-mers POEGMA brushes were studied for antifouling using a BCA protein assay. The mats with 30-mers grafted brushes exhibited excellent antifouling efficiency, ~82% of proteins repelled, compared to the pristine sSEBS-PEDOT fibre mat. The grafted fibre mats exhibited cell viability >80%, comparable to the standard cell culture plate controls. Such conducting, porous biointerfaces with POEGMA grafted brushes are suitable for applications in various biomedical devices, including biosensors, liquid biopsy, wound healing substrates and drug delivery systems. Full article

The manipulation and understanding of molecular transport across functionalized nanopores will take us closer to mimicking biological membranes and thus to design high-performance permselective separation systems. In this work, Surface-initiated atom transfer radical polymerization (SI-ATRP) of (2-methacryloyloxy)-ethyltrimethylammonium chloride (METAC) was performed on both mesoporous silica and mesoporous titania thin films. Pores were proven to be filled using ellipsometry and diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS). Furthermore, the employed method leads to a polymer overlayer, whose thickness could be discriminated using a double-layer ellipsometry model. Cyclic voltammetry experiments reveal that the transport of electrochemically active probes is affected by the PMETAC presence, both due to the polymer overlayer and the confined charge of the pore-tethered PMETAC. A more detailed study demonstrates that ion permeability depends on the combined role of the inorganic scaffolds’ (titania and silica) surface chemistry and the steric and charge exclusion properties of the polyelectrolyte. Interestingly, highly charged negative walls with positively charged polymers may resemble zwitterionic polymer behavior in confined environments. Full article

Beneficiation wastewater contains various types of pollutants, such as heavy metal ions and organic pollutants. In this work, a silica-based amphiphilic block copolymer, SiO₂–g–PBMA–b–PDMAEMA, was obtained by surface-initiated atom transfer radical polymerization (SI-ATRP) for Cu(II) and sodium oleate adsorption in beneficiation wastewater, using butyl methacrylate (BMA) as a hydrophobic monomer and 2-(dimethylamino)ethylmethacrylate (DMAEMA) as a hydrophilic monomer. FTIR, TGA, NMR, GPC, XRD, N₂ adsorption–desorption isotherms and TEM were used to characterize the structure and morphology of the hybrid adsorbent. The introduction of PBMA greatly increased the adsorption of sodium oleate on SiO₂–g–PBMA–b–PDMAEMA. Adsorption kinetics showed that the adsorption of Cu(II) or sodium oleate on SiO₂–g–PBMA–b–PDMAEMA fitted the pseudo-second-order model well. Adsorption isotherms of Cu(II) on SiO₂–g–PBMA–b–PDMAEMA were better described by the Langmuir adsorption isotherm model, and sodium oleate on SiO₂–g–PBMA–b–PDMAEMA was better described by the Freundlich adsorption isotherm model. The maximum adsorption capacity of Cu(II) and sodium oleate calculated from Langmuir adsorption isotherm equation reached 448.43 mg·g⁻¹ and 129.03 mg·g⁻¹, respectively. Chelation and complexation were considered as the main driving forces of Cu(II) adsorption, and the van der Waals force as well as weak hydrogen bonds were considered the main driving forces of sodium oleate adsorption. The adsorbent was recyclable and showed excellent multicomponent adsorption for Cu(II) and sodium oleate in the mixed solution. SiO₂–g–PBMA–b–PDMAEMA represents a satisfying adsorption material for the removal of heavy metal ions and organic pollutants in beneficiation wastewater. Full article