Search Results (99)

Radio frequency (RF) energy harvesting offers a potential power source for low-power Internet of Things and wireless sensing nodes, but compact rectifiers must balance impedance matching, multiband response, and load-driving capability. This work presents a compact SMS7621 Schottky-diode RF rectifier for RF-powered wireless sensing applications. An 11-segment microstrip distributed-parameter collaborative optimization strategy is used to tune impedance transformation in a 3.48 cm × 1.98 cm single-layer layout while compensating for diode nonlinear impedance variation and package parasitics. Simulations show more than 40% RF-to-DC conversion efficiency from 1.90 to 2.35 GHz, with additional efficiency peaks of 40.55% at 4.45 GHz and 38.45% at 7.15 GHz. Measurements verify the 2.45 GHz output performance under controlled high-input-power excitation: with a 300 Ω load and 25 dBm input, the rectifier delivers a maximum DC voltage of 5.42 V. At 15 dBm input, the measured peak efficiency reaches 46.05% at 2 GHz and remains 35.69% at 4 GHz. These results indicate a compact rectifier front end with multiband harvesting potential and 5 V-class load-driving capability under dedicated RF powering conditions. Full article

This paper proposes a compact axial-ratio-enhanced wideband circularly polarized rectenna for ambient RF energy harvesting. The proposed rectenna is designed to operate across the mainstream Wi-Fi (2.45 GHz) and 5G (2.6 GHz and 3.5 GHz) communication bands, achieving efficient RF energy capture and effective direct current (DC) conversion. From a design perspective, the proposed approach is developed based on parasitic-element-enabled current redistribution for broadband circular polarization and nonlinear-aware multi-stage impedance matching for wideband rectification. The receiving antenna is based on a crossed-dipole configuration integrated with quarter-ring elements. By employing techniques such as slotting and incorporating additional parasitic patches, a fractional 3-dB axial ratio bandwidth (ARBW) of 52.7% (2.39–4.10 GHz) is achieved, with a peak radiation efficiency of 90% and an average efficiency of 76% within the operating band. To realize wideband impedance matching with the receiving antenna, the rectifying circuit adopts a single-shunt diode half-wave topology, combining L-type and T-type matching networks to significantly extend the operating bandwidth. Experimental results demonstrate that at input power levels of 7 dBm, 7 dBm, and 9 dBm, the rectifier achieves peak conversion efficiencies of 56.7%, 59.8%, and 56.3% at the three target frequencies (2.45 GHz, 2.6 GHz, and 3.5 GHz), respectively. Furthermore, the rectifier exhibits stable rectification performance across a wide input power dynamic range from −15 dBm to 7 dBm. Consequently, the proposed rectenna holds significant application value for passive IoT nodes, low-power sensors, and self-sustainable electronic devices. Full article

ZnO and CuO thin films were deposited separately using the radio frequency (RF) sputtering technique, and the effect of annealing in nitrogen and oxygen ambient environments was investigated. In this article, structural, optical, vibrational, and electrical characterizations were sequentially performed using techniques such as X-ray diffraction (XRD), UV–visible spectroscopy (UV-vis), Raman spectroscopy, photoluminescence (PL) spectroscopy, and current-voltage measurements using a DC four-probe station. XRD confirmed a high-crystallinity and wurtzite structure for ZnO, with the preferred orientation being along the c-axis (0001), and a monoclinic structure for CuO, with preferential orientation along the (002) axis. The absorption edges of the ZnO and CuO thin films were determined to be 3.24 eV and 2.89 eV, respectively. However, Urbach tails were observed only in the ZnO thin films, confirming the presence of localized Zn interstitials and oxygen vacancies. The absorption of CuO showed weak Urbach tails, suggesting that the defects were not localized. Raman spectroscopy performed on the ZnO and CuO thin films showed the appearance of weak E₂(high) and prominent A_g/B_2g modes, confirming the presence of ZnO and CuO bonding states, respectively. PL studies revealed room temperature emission for both the CuO and ZnO thin films, which is crucial for thin film solar cells and photodetectors. Two thin film heterostructures were fabricated with and without MoS₂ (a hole transport layer) on FTO substrates. The Al/FTO/CuO/ZnO/Al heterostructure revealed a rectifying behavior with a photo current of 2 mA in the dark, whereas light-induced characteristics resulted in a photocurrent of 5 mA. The Al/FTO/MoS₂/CuO/ZnO/Al heterostructure exhibited a similar rectifying behavior, with improved photo currents of 5 mA in the dark and 9 mA in the light. Full article

Passive radio frequency identification (RFID) sensing systems integrate wireless energy transfer with information identification. However, conventional passive RFID systems still face three key challenges in practical applications: low RF energy harvesting efficiency, high power consumption of sensor loads, and high complexity of tag anti-collision algorithms. To address these issues, this paper proposes a hardware–software co-optimized RFID sensor system. For hardware, low threshold RF Schottky diodes are selected, and an input inductor is introduced into the voltage multiplier rectifier to boost the signal amplitude, thereby enhancing the radio frequency to direct current (RF-DC) energy conversion efficiency. In terms of loading, a low-power management strategy is implemented for the power supply and control logic of the sensor node to minimize the overall system energy consumption. For algorithmic implementation, a Dual-Threshold Stepped Dynamic Frame Slotted ALOHA (DTS-DFSA) anti-collision algorithm is proposed, which adaptively adjusts the frame length based on the observed collision ratio, eliminating the need for complex tag population estimation. The algorithm features low computational complexity and is well suited for resource constrained embedded platforms. Through simulation validation, we compare the conversion efficiency of the RF energy harvesting circuit before and after improvement, the current of the sensor load in active and idle states, and the performance of the proposed algorithm against the low-complexity DFSA (LC-DFSA). The results show that the maximum conversion efficiency of the improved RF energy harvesting circuit has increased from 60.56% to 68.69%; specifically, the sensor load current drastically drops from approximately 2.0 $\mathrm{m}\mathrm{A}$ in the active state to around 74 $\mathsf{\mu }\mathrm{A}$ in the idle state, validating the efficacy of the proposed power gating strategy, and the proposed DTS-DFSA algorithm outperforms existing low-complexity schemes in both identification efficiency and computational complexity. Full article

Microwave wireless power transfer (MWPT) technology has the advantages of long distance and high transmission efficiency; therefore, MWPT has many applications in aerospace, space solar power stations (SSPSs), and so on. The receiving and fixing subsystem is the core component for gathering and converting power and it is the main part of the system. If this step is both efficient and possible, the whole system will also be efficient and its success possible. This paper mainly introduces a systematic review of the key technologies, research status, and development trends of the receiving-end part in MWPT. High-performance rectifying devices are analyzed in detail, with the use of GaN Schottky barrier diodes (GaN SBDs), in addition to rectification circuits that have good rectification and impedance matching. Additionally, it compares the advantages and disadvantages of three power synthesis architectures, including RF synthesis, DC synthesis, and hybrid subarray synthesis, and proposes a strategy for optimizing power distribution through intelligent subarray partitioning. Finally, this paper looks at future development trends in receiving-end technology, including miniaturized monolithic microwave integrated circuits (MMICs) and efficient broadband reconfigurable rectification. The research presented herein offers a systematic technical reference and theoretical foundation for enhancing the performance of the receiving ends in microwave wireless power transfer systems. Full article

In this work, a dual-band, dual-mode, circularly polarized fully woven textile antenna with capability for Simultaneous Wireless Information and Power Transfer (SWIPT) in wearable applications is presented. The power and the data transfer modes work at 2.4 and 5.4 GHz, respectively. The radiating element is based on a square patch with an asymmetrical U-shaped slot and a chamfered corner. A single-diode rectifier, required for the power transfer mode, is mounted on a carrier thread and then connected to the antenna through a T-match network located at one of the patch corners. This feeding technique simultaneously provides complex conjugate matching to the rectifier and circular polarization. On the other hand, a coaxial probe port is used for the data transfer mode. A prototype was implemented and experimentally characterized. Regarding the power transfer mode, the measured RF-DC conversion efficiency is about 50% when the available power at the rectifier input is −10 dBm, and the axial ratio is smaller than 3 dB. In the data transfer mode, the antenna gain and the axial ratio are 0 and 2 dB, respectively. The experimental results are in good agreement with simulations, validating the proposed structure and design methods, and they are comparable to the state of the art for textile antennas/rectennas. Furthermore, the combination of the fully woven technology and the proposed single-layer layout provides a large degree of integration and robustness, which are valuable characteristics for wearable devices. Full article

This article presents a comprehensive and intuitive analysis of the impact of packaging on diode performance and a two-step method for packaging parameter extraction. This is performed using a single forward bias point, one-port measurements and probe tips on a conventional printed circuit board (PCB). A PIN diode was used to validate the method, biased from reverse (−5 V) to forward (1.22 V) bias. Measurements were performed up to 27 gigahertz (GHz). The complete diode characterization process—from the design and the electrical modeling of the test fixture to the extraction of the unpackaged diode measurements—is detailed. The parameters of the package model were extracted, its effects were removed from the measurement, and the behavior of the unpackaged diode was determined. Three operating regions based on their radiofrequency and direct current (RF-DC) behavior were proposed, and an electrical model of the unpackaged diode was derived for each region. The results showed that the influence of the package caused the diode to remain in an unchanged behavior under different biases, indicating that it no longer rectified. The results presented herein are validated by the excellent correlation between the diode’s measured S-parameters, impedance, and admittance and their corresponding models. Full article

The widespread integration of low-power electronic devices in IoT, biomedical, and sensing applications has intensified the demand for energy-autonomous solutions. Radio Frequency Energy Harvesting (RFEH) offers a promising alternative by leveraging ambient RF signals available in both indoor and outdoor environments. Despite its conceptual appeal, practical deployment still faces major challenges. This systematic literature review (SLR) examines 25 recent studies, following the PRISMA methodology, to provide a comprehensive overview of current RFEH architectures. It focuses on three critical components: receiving antennas, impedance matching circuits (IMCs), and RF-to-DC rectifiers. Design strategies are reviewed and compared across antenna types, matching techniques, and rectifier configurations. The review also highlights persistent challenges and outlines directions for the development of compact, efficient, and robust energy-harvesting systems for next-generation wireless technologies. Full article

This paper presents an advanced radio frequency (RF)–direct current (DC) power conversion architecture based on a multistage Cockcroft–Walton topology. The proposed design achieves an enhanced voltage conversion ratio while maintaining superior RF-DC conversion efficiency under low input power conditions. To address the inherent limitations of cascading Cockcroft–Walton topologies with class-F load networks, a novel ground plane isolation technique was developed, which utilizes the reverse-side metallization of the circuit board. A 5.8 GHz two-stage Cockcroft–Walton voltage multiplier rectifier was fabricated and characterized. Measurement results demonstrate that the circuit achieves a maximum output voltage of 7.4 V and a peak conversion efficiency of 70.5% with an input power of only 30 mW, while maintaining stable performance across varying load conditions. A comparison with a two-stage Dickson rectifier reveals that the Cockcroft–Walton rectifier exhibits superior output voltage and conversion efficiency. The proposed architecture delivers significant improvements in power conversion efficiency and voltage multiplication capability compared to conventional designs, establishing a new benchmark for low-power wireless energy harvesting applications. Full article

A nonlinear state-space model for Schottky diode rectifiers is presented that incorporates junction dynamics, layout parasitic effects, and electromagnetic coupling effects. Unlike prior approaches, the model resolves conduction intervals under harmonic-rich excitation and integrates electromagnetic voltage–current feedback to capture field-induced perturbations at high frequencies. The framework was validated through the design of a 5.8 GHz rectifier, achieving 62% RF–DC efficiency at −10 dBm into a 500 Ω load, with close agreement between the simulation and measurement. The results confirm the model’s predictive accuracy and its utility for high-efficiency rectenna systems in microwave and terahertz applications. Full article

The rapid growth of low-power Internet of Things (IoT) applications has created an urgent demand for compact, battery-free power solutions. However, most existing RF energy harvesters rely on active rectifiers, multi-phase topologies, or complex tuning networks, which increase circuit complexity and static power overhead while struggling to maintain high efficiency under microwatt-level inputs. To address this challenge, this work proposes a harmonic-recycling, passive, RF-energy-harvesting system with integrated power management (HR-P-RFEH). The system adopts a planar microstrip architecture compatible with MEMS fabrication, integrating a dual-stage voltage multiplier rectifier (VMR) and a stub-based harmonic suppression–recycling network. The design was verified through combined electromagnetic/circuit co-simulations, PCB prototyping, and experimental measurements. Operating at 915 MHz under a 0 dBm input and a 2 k$\Omega$ load, the HR-P-RFEH achieves a stable 1.4 V DC output and a peak rectification efficiency of 70.7%. Compared with a conventional single-stage rectifier, it improves the output voltage by 22.5% and the efficiency by 16.4%. The rectified power is further regulated by a BQ25570-based unit to provide a stable 3.3 V supply buffered by a 47 mF supercapacitor, ensuring continuous operation under intermittent RF input. In comparison with the state of the art, the proposed fully passive, harmonic-recycling design achieves competitive efficiency without active bias or adaptive tuning while remaining MEMS- and LTCC-ready. These results highlight HR-P-RFEH as a scalable and fabrication-friendly building block for next-generation energy-autonomous IoT and MEMS systems. Full article

This paper proposes a hybrid energy-harvesting chip that utilizes both radio-frequency (RF) energy and solar energy for low-power applications and extended service life. The key contributions include a wide input power range, a compact chip area, and a high maximum power conversion efficiency (PCE). Solar energy is a clean and readily available source. The hybrid energy harvesting system has gained popularity by combining RF and solar energy to improve overall energy availability and efficiency. The proposed chip comprises a matching network, rectifier, charge pump, DC combiner, overvoltage protection circuit, and low-dropout voltage regulator (LDO). The matching network ensures maximum power delivery from the antenna to the rectifier. The rectifier circuit utilizes a cross-coupled differential drive rectifier to convert radio frequency energy into DC voltage, incorporating boosting functionality. In addition, a solar harvester is employed to provide an additional energy source to extend service time and stabilize the output by combining it with the radio-frequency source using a DC combiner. The overvoltage protection circuit safeguards against high voltage passing from the DC combiner to the LDO. Finally, the LDO facilitates the production of a stable output voltage. The entire circuit is simulated using the Taiwan Semiconductor Manufacturing Company 0.18 µm 1P6M complementary metal–oxide–semiconductor standard process developed by the Taiwan Semiconductor Research Institute. The simulation results indicated a rectifier conversion efficiency of approximately 41.6% for the proposed radio-frequency-energy-harvesting system. It can operate with power levels ranging from −1 to 20 dBm, and the rectifier circuit’s output voltage is within the range of 1.7–1.8 V. A 0.2 W monocrystalline silicon solar panel (70 × 30 mm²) was used to generate a supplied voltage of 1 V. The overvoltage protection circuit limited the output voltage to 3.6 V. Finally, the LDO yielded a stable output voltage of 3.3 V. Full article

This paper presents a rectifying metasurface (RMS) that enables wide-angle, polarization-insensitive wireless energy harvesting in the Wi-Fi frequency range. The RMS consists of a metasurface integrated with rectifying diodes, a low-pass filter (LPF), and a resistive load. In the structural design, the RMS incorporates four Schottky diodes placed on the bottom structure and connected to the top structure through four metallized vias. This configuration facilitates impedance matching between the metasurface and the diodes, omitting the need for conventional rectifier circuits or external matching networks and removing the impact of soldering variations. A 3 × 3 RMS prototype was manufactured and subjected to experimental validation. The measurements confirm that the RMS achieves a peak RF-to-DC conversion efficiency of 68.3% at 5.8 GHz with a 12.5 dBm input power, while maintaining stable performance across a wide range of incident angles and polarization states. Full article

This paper presents a novel fully integrated radio frequency (RF) rectifier tailored for a wide power dynamic range (PDR) with multiband adaptability to efficiently convert AC RF power into DC power. The proposed rectifier utilizes the strength of interstage gate biasing to achieve high power conversion efficiency (PCE) across a broad range of input power levels. Through its reconfigurable mode, the circuit seamlessly transitions between a low-power path and high-power path to ensure optimal performance across a wide PDR. Simulated using CMOS 65 nm technology, the post-layout assessment reveals a peak PCE of 48.8% at 900 MHz and 46.4% at 1800 MHz, with an extensive PDR of 20 dB for PCE exceeding 20% at both frequencies. Full article

This paper put forward a hybrid energy harvester for collecting RF and solar energy in quad-band (GSM-900/1800, ISM-2400 and WiMAX-3500). By introducing diverse parasitic structures, good impedance matching with unidirectional radiation is achieved in the multi-band. Below the solar antenna, a low-power rectifier circuit is employed to achieve broadband rectification. Under the input power of 0 dBm, and maximum RF-DC conversion efficiency of 56.94% is realized. Accordingly, the hybrid energy harvester collects RF and solar energy individually or simultaneously, and then converts it into DC for power supply. With a light intensity of 1500 lux, the solar cell obtains 1.732 mW, and the rectenna can harvest additional 0.37–0.405 mW power. The proposed RF–Solar energy harvester has the advantages of multi-frequency operation, high gain, and high energy harvesting conversion efficiency. Full article