Search Results (1,007)

In this study, we report the synthesis, characterization, and performance evaluation of a series of bimetallic Pt_xRh_y/C electrocatalysts with systematically varied Rh content for glycerol electrooxidation in acidic and alkaline media. The catalysts were prepared via a polyol reduction method using ethylene glycol as both a solvent and reducing agent, with prior functionalization of Vulcan XC-72 carbon to enhance nanoparticles (NPs) dispersion. High-resolution transmission electron microscopy (HRTEM), energy-dispersive X-ray spectroscopy (EDS), and X-ray diffraction (XRD) analyses indicated the spatial co-location of Rh atoms alongside Pt atoms. Electrochemical studies revealed strong composition-dependent behavior, with Pt₉₅Rh₅/C exhibiting the highest activity toward glycerol oxidation. To elucidate the origin of raised results, density functional tight binding (DFTB) simulations were conducted to model atomic distributions and evaluate energetic parameters. The results showed that Rh atoms preferentially segregate to the surface at higher concentrations due to their lower surface energy, while at low concentrations, they remain confined within the Pt lattice. Among the series, Pt₉₅Rh₅/C exhibited a distinctively higher excess energy and less favorable binding energy, rationalizing its lower thermodynamic stability. These findings reveal a clear trade-off between catalytic activity and structural durability, highlighting the critical role of the composition and nanoscale architecture in optimizing Pt-based electrocatalysts for alcohol oxidation reactions. Full article

In this work, the photocatalytic reduction of CO₂ was innovatively tested with the simultaneous removal and mineralization of a textile contaminant, methylene blue (MB), which acts as a sacrificial agent. The process was carried out in a flow regime under atmospheric conditions, using a liquid-phase photoreactor under UVA illumination with a duration of 24 h per test. Two commercial TiO₂-based photocatalysts, P25 and P90 from Evonik, were used and surface modified through the photodeposition of metallic nanoparticles of Pt, Au, and Pd, as they did not show gas-phase products from CO₂ reduction on their own. The optimal pH was 5, the decreasing order of activity by metal was Pt > Au > Pd, and the optimal MB concentration was 20 ppm. The major products were CH₄ and H₂ in the gas phase. The presence of CH₄ was only detected in the presence of a CO₂ flow. In the liquid phase, carboxylic acids were also detected in small amounts, and in the test, 100 ppm of MB ethanol was additionally detected. A 100% degradation of MB and 72.5% mineralization was achieved under the conditions of highest CH₄ production (20 ppm MB at pH 5 with 4 g·L⁻¹ P25-0.70%Pt). Full article

Even though Pt(II)-based drugs represent the standard in cancer therapy, their use is seriously limited by severe side-effects (renal toxicity, allergic reactions, gastrointestinal disorders, hemorrhage and hearing loss), drug resistance and a grim prognosis. This review presents the results of multiple studies showing different nanoparticle-based platforms as delivery agents in order to overcome these drawbacks. The approach of using nanoparticle-based drug delivery systems of Pt drugs and prodrugs is promising due to key advantages like specific targeting and thereby reduced toxicity to healthy cells; increased stability in the bloodstream; multiple mechanisms of action such as stimulating anti-tumor immunity, responding to environmental stimuli (light, pH, etc.), or penetrating deeper into tissues; enhanced efficacy by their combination with other therapies (chemotherapy, gene therapy) to amplify the anti-tumor effect. However, certain challenges need to be overcome before these solutions can be widely applied in clinics. These include issues related to biocompatibility, large-scale production, and regulatory approvals. In conclusion, using nanoparticles to deliver Pt-based drugs represents an advanced and highly promising strategy to make chemotherapy more effective and less toxic. Nonetheless, further studies are required for the better understanding of intracellular mechanisms of action, toxicity and the pharmacokinetics of nanoparticles, and physical–chemical standardization. Full article

Current Pt-based methane combustion catalysts require high noble metal loadings (≥1 wt%) and exhibit insufficient low-temperature activity. To address this, we developed a 0.5 wt% Pt catalyst supported by sulfate-modified Fe-Ce-TiO₂ (denoted 0.5Pt/CFT-TS) via sol–gel synthesis using titanium oxysulfate (TiOSO₄) precursor. Control catalysts prepared with TiCl₄, titanium butoxide, or commercial TiO₂ showed inferior performance. Structural characterization revealed that the TiOSO₄ derived carrier possesses a mesoporous framework (156.2 m²/g surface area, 8.1 nm pore size) with residual SO₄²⁻ inducing strong Brønsted acidity (1.23 mmol/g NH₃ adsorption) and elevated Ce³⁺ concentration (49.45%). These properties synergistically enhanced oxygen vacancy density (51.16% O_α fraction) and stabilized sub-nm Pt nanoparticles. The resulting Pt⁰-Fe³⁺/Ce⁴⁺-Oᵥ interface facilitated dynamic redox cycling (Fe³⁺ + Ce⁴⁺ + 0.5O²⁻ ⇌ Fe²⁺ + Ce³⁺ + 0.5Oᵥ + 0.25O₂), lowering oxygen vacancy regeneration barriers (H₂-TPR peak reduced by 45 °C) and decreasing methane activation energy to 46.77 kJ/mol. This catalyst achieved T₉₀ = 163 °C and complete conversion at 450 °C under industrial conditions (1% CH₄/4% O₂, GHSV = 30,000 h⁻¹), establishing a novel design strategy for low-Pt combustion catalysts. Full article

The development of effective catalysts for the oxygen reduction reaction (ORR) is crucial for improving the performance of fuel cells. Efficient carbon-supported Pt-Co nanocatalysts were successfully prepared by a generic two-step method: (i) electroless deposition of a Co-P coating on Vulcan XC72R carbon powder and (ii) subsequent spontaneous partial galvanic replacement of Co by Pt, upon immersion of the Co/C precursor in a chloroplatinate solution. The prepared Pt-Co particles (of a core-shell structure) are dispersed on a Vulcan XC-72 support, forming agglomerates made of nanoparticles smaller than 10 nm. The composition and surface morphology of the samples were characterized by scanning electron microscopy and energy-dispersive X-ray spectroscopy (SEM/EDS) as well as transmission electron microscopy (TEM). The crystal structures of the Co-P/C precursor and Pt-Co/C catalyst were investigated by X-ray diffraction (XRD). XPS analysis was performed to study the chemical state of the surface layers of the precursor and catalyst. The electrochemical behavior of the Pt-Co/C composites was evaluated by cyclic voltammetry (CV). Linear sweep voltammetry (LSV) experiments were used to assess the catalytic activity towards the ORR and compared with that of a commercial Pt/C catalyst. The Pt-Co/C catalysts exhibit mass-specific and surface-specific activities (of j_m = 133 mA mg⁻¹ and j_esa = 0.661 mA cm⁻², respectively) at a typical overpotential value of 380 mV (+0.85 V vs. RHE); these are superior to those of similar electrodes made of a commercial Pt/C catalyst (j_m = 50.6 mA mg⁻¹; j_esa = 0.165 mA cm⁻²). The beneficial effect of even small (<1% wt.%) quantities of Co in the catalyst on Pt ORR activity may be attributed to an optimum catalyst composition and particle size resulting from the proposed preparation method. Full article

Environmental contamination is a critical global concern, primarily due to detrimental greenhouse gas (GHG) emissions, especially carbon dioxide (CO₂), which significantly contribute to climate change. Moreover, the presence of harmful heavy metals like Ni, Cd, Cu, Hg, and Pb in soil and water ecosystems has led to poor water quality. Noble metal nanoparticles (MNPs), for instance, Pd, Ag, Pt, and Au, have emerged as promising solutions for addressing environmental pollution. However, the practical utilization of MNPs faces challenges as they tend to aggregate and lose stability. To overcome this issue, the reverse double-solvent method (RDSM) was utilized to synthesis melamine-based porous polyaminals (POPs) as a supportive material for the in situ growing of silver nanoparticles (Ag NPs). The porous structure of melamine-based porous polyaminals, featuring aminal-linked (-HN-C-NH-) and triazine groups, provides excellent binding sites for capturing Ag⁺ ions, thereby improving the dispersion and stability of the nanoparticles. The resulting material exhibited ultrafine particle sizes for Ag NPs, and the incorporation of Ag NPs within the porous polyaminals demonstrated a high surface area (~279 m²/g) and total pore volume (1.21 cm³/g), encompassing micropores and mesopores. Additionally, the Ag NPs@POPs showcased significant capacity for CO₂ capture (2.99 mmol/g at 273 K and 1 bar) and effectively removed Cu (II), with a remarkable removal efficiency of 99.04%. The nitrogen-rich porous polyaminals offer promising prospects for immobilizing and encapsulating Ag nanoparticles, making them outstanding adsorbents for selectively capturing carbon dioxide and removing metal ions. Pursuing this approach holds immense potential for various environmental applications. Full article

In this study, MnO₂-CNTs composite support was prepared by citric acid reduction method, and then, Pt nanoparticles were loaded on the surface by ethylene glycol reduction method to obtain a series of Pt/xMnO₂-CNTs catalysts. Structural characterization (TEM, XRD, HRTEM) showed that Pt nanoparticles were uniformly dispersed on the surface of the catalyst with an average particle size of 3.6 nm. Electrochemical tests show that when the content of MnO₂ is 20 wt.%, the Pt/_20wt.%MnO₂-CNTs catalyst has the best methanol oxidation performance, and its mass activity and long-term stability are 4.0 times and 5.41 times that of commercial Pt/C, respectively. The in situ FTIR results showed that MnO₂ promoted the dissociation of water through synergistic effect, generated abundant OH species, accelerated the oxidation of CO intermediates, and inhibited the poisoning of Pt sites. In this study, it is clear that the excellent performance of Pt/xMnO₂-CNTs is due to multiple synergistic effects. Modified carbon nanotubes facilitate proton conduction, Pt nanoparticles effectively activate methanol, and MnO₂ modulates reaction intermediates via its bifunctional mechanism. This comprehensive mechanism understanding provides a theoretical basis for the design of high-performance catalysts for direct methanol fuel cells. Full article

Photodynamic therapy (PDT) is a promising, minimally invasive treatment for cervical cancer, but its efficacy is significantly limited by hypoxia—oxygen deficiency in the tumour microenvironment. The aim of this study was to present strategies to counteract hypoxia in PDT using the latest nanotechnologies. Based on a review of the literature available in PubMed/MEDLINE, Scopus, and Web of Science databases, covering the period from January 2024 to March 2025, nine original in vivo studies were identified that investigated the use of nanoparticle-based strategies to overcome hypoxia and enhance the efficacy of PDT in cervical cancer. A variety of approaches to improve tumour oxygenation are described, including the catalytic decomposition of hydrogen peroxide (H₂O₂) with manganese oxide (MnO₂), the use of bimetallic nanozymes (e.g., Au₂Pt), and FeOOH structures and oxygen storage and control systems (e.g., endoperoxides). Strategies to reduce oxygen consumption by cancer cells, such as nitric oxide (NO) release or inhibition of mitochondrial oxidative phosphorylation, are also discussed. The review shows that appropriately designed nanoparticles can effectively counteract hypoxia, enhancing the efficacy of PDT by intensifying reactive oxygen species (ROS) generation and modulating HIF-1α factor expression. The strategies presented here have the potential to significantly improve the efficacy of photodynamic therapy in the treatment of cervical cancer, especially under conditions of limited oxygen availability. Full article

The large-scale implementation of direct methanol fuel cells (DMFCs) is significantly impeded by sluggish methanol oxidation reaction (MOR) kinetics, degradation of Pt electrocatalysts, and significant carbon support corrosion in commercial Pt/C. Herein, we design a mesoporous hollow TiO₂@carbon core–shell composite (MH-TiO₂@C) as a support for Pt nanoparticles to serve as an efficient MOR electrocatalyst. Pt/MH-TiO₂@C demonstrates exceptional MOR activity in alkaline electrolyte, exhibiting a mass activity 2.56-fold higher than commercial Pt/C. Furthermore, Pt/MH-TiO₂@C displays remarkable durability compared to Pt/C. Following chronoamperometry tests, the mass activity of Pt/MH-TiO₂@C decreased by 30.92%, substantially lower than the 52.31% loss observed for commercial Pt/C. The superior MOR activity and durability originate from the inherent structural stability of the MH-TiO₂@C composite, strong metal-support interaction between Pt and TiO₂, and enhanced resistance to intermediate poisoning. This work presents a feasible strategy for developing efficient and durable Pt-based electrocatalysts, accelerating the commercialization of DMFCs. Full article

Acute lymphoblastic leukemia (ALL) represents the most common type of cancer in the pediatric population. The (1;19)(q23;p13) translocation is a primary chromosomal abnormality present in 3–12% of ALL cases. The current study aims to develop a label-free innovative nanodevice for the ultrasensitive diagnosis of the TCF3-PBX1 chimeric oncogene, featuring simplified operation and rapid analysis using minimal sample volumes, which positions it as a superior alternative for clinical diagnostics and early leukemia identification. The biosensor system was engineered on a nanostructured platform composed of polypyrrole (PPy) and a novel chemically functionalized hybrid nanocomposite of platinum nanospheres and titanium dioxide nanoparticles (TiO₂@Pt). Single-stranded oligonucleotide sequences were chemically immobilized on the nanoengineered transducer to enable biospecific detection. Cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), ultraviolet-visible spectroscopy (UV-Vis), and atomic force microscopy (AFM) were used to characterize each stage of the biotechnological device fabrication process. The analytical properties of the sensing tool were explored using recombinant plasmids containing the TCF3-PBX1 oncogenic sequence and clinical specimens from pediatric patients with B-cell ALL. After exposing the molecular monitoring system to the genetic target, significant variations were observed in the voltammetric oxidation current (∆I = 33.08% ± 0.28 to 124.91% ± 17.08) and in the resistance to charge transfer (ΔR_CT = 19.73% ± 0.96 to 83.51% ± 0.84). Data analysis revealed high reproducibility, with a relative standard deviation of 3.66%, a response range from 3.58 aM to 357.67 fM, a detection limit of 19.31 aM, and a limit of quantification of 64.39 aM. Therefore, a novel nanosensor for multiparametric electrochemical screening of the TCF3-PBX1 chimeric oncogene was described for the first time, potentially improving the quality of life for leukemic patients. Full article

Excessive use of antibiotics can lead to antibiotic resistance, posing a significant threat to human health and the environment. Chloramphenicol (CAP), once widely used, has been banned in many regions for over 20 years due to its toxicity. Detecting CAP residues in food products is crucial for regulating safe use and preventing unnecessary antibiotic exposure. Electrochemical sensors are low-cost, sensitive, and easily detect CAP. This paper reviews recent research on electrochemical sensors for CAP detection, with a focus on the materials and fabrication techniques employed. The sensors are evaluated based on key performance parameters, including limit of detection, sensitivity, linear range, selectivity, and the ability to perform simultaneous detection. Specifically, we highlight the use of metal and carbon-based electrode modifications, including gold nanoparticles (AuNPs), nickel–cobalt (Ni-Co) hollow nano boxes, platinum–palladium (Pt-Pd), graphene (Gr), and covalent organic frameworks (COFs), as well as molecularly imprinted polymers (MIPs) such as polyaniline (PANI) and poly(o-phenylenediamine) (P(o-PD)). The mechanisms by which these modifications enhance CAP detection are discussed, including improved conductivity, increased surface-to-volume ratio, and enhanced binding site availability. The reviewed sensors demonstrated promising results, with some exhibiting high selectivity and sensitivity, and the effective detection of CAP in complex sample matrices. This review aims to support the development of next-generation sensors for antibiotic monitoring and contribute to global efforts to combat antibiotic resistance. Full article

Amperometric biosensors, due to their high sensitivity, fast response time, low cost, simple control, miniaturization capabilities, and other advantages, are receiving significant attention in the field of medical diagnostics, especially in monitoring blood glucose levels in diabetic patients. In this study, an amperometric glucose biosensor based on immobilized enzyme glucose oxidase (GOx) and bimetallic platinum cobalt (PtCo) nanoparticles was developed. The PtCo nanoparticles, deposited on a graphite rod electrode, exhibited peroxidase-like catalytic properties and were able to electrocatalyze the reduction of H₂O₂. After immobilization of the GOx, an amperometric signal generated by the biosensor was directly proportional to the glucose concentration in the range of 0.04–2.18 mM. The biosensor demonstrated a sensitivity of 19.38 μA mM⁻¹ cm⁻², with a detection limit of 0.021 mM and a quantification limit of 0.064 mM. In addition to this analytical performance, the biosensor exhibited excellent repeatability (relative standard deviation (RSD) was 4.90%); operational and storage stability, retaining 98.93% and 95.33% of its initial response after 26 cycles of glucose detection and over a 14-day period, respectively; and anti-interference ability against electroactive species, as well as exceptional selectivity for glucose and satisfactory reproducibility (RSD 8.90%). Additionally, the biosensor was able to detect glucose levels in blood serum with a high accuracy (RSD 5.89%), indicating potential suitability for glucose determination in real samples. Full article

A major challenge for Li-O₂ batteries is the slow kinetics of oxygen reduction (ORR) and evolution (OER) reactions. This work presents a high-performance Pt₃Rh/C composite cathode where Pt-Rh nanoalloys are uniformly dispersed on 3D nanoporous carbon. The bimetallic architecture demonstrates significantly enhanced ORR/OER activity compared to conventional catalysts. Super P, with a large specific surface area and omnipresent pores with diverse size distribution, provided sufficient storage space for Li₂O₂ and facilitated transport channels for Li⁺ and O₂, while the highly conductive Pt₃Rh NPs optimized catalytic efficiency. XPS reveals a prominent electron transfer process between Pt and Rh; the Rh sites in Pt₃Rh/C alloy can effectively act as electron donors to improve the oxygen/lithium peroxide (O₂/Li₂O₂) redox chemistry in LOB. Therefore, the Pt₃Rh/C electrode shows the minimum overpotential (0.60 V) for efficient oxygen reduction and evolution under an upper-limit capacity of 2000 mAh g⁻¹. This work introduces a Pt₃Rh/C nanoalloy synthesis method that boosts Li-O₂ battery efficiency by accelerating oxygen reaction kinetics. Full article

Nb₂O₅ (niobia) coatings were prepared by spin coating of niobium sol, synthesized using niobium chloride as the precursor and ethanol and water as solvents, followed by high-temperature annealing. Doping of the films was achieved by incorporating commercially available SiO₂ (Ludox) and noble metal nanoparticles (NPs) into the sol prior to its deposition. Various sizes of Pt (5 and 30 nm), Ag (10, 20, and 40 nm), and Au (5, 10, and 20 nm) NPs were used to enhance sensing behavior of coatings. After annealing, films were subjected to chemical etching to remove the silica phase. This process generated porosity within the films, which in turn enabled the tailoring of both their optical and sensing properties. It was demonstrated that both the type and size of the incorporated nanoparticles significantly influenced the sensing behavior. The most effective enhancement was observed with the addition of 10 nm AuNPs. Optical characterization indicated that 10 nm AuNPs had a minimal effect on the optical properties. In contrast, doping with 20 nm AuNPs led to a reduction in the refractive index and an increase in Urbach energy. No significant alteration in the optical band gap due to doping was observed. Full article

The development of gas sensors with high sensitivity and low operating temperatures is essential for practical applications in environmental monitoring and industrial safety. SnO₂-based gas sensors, despite their widespread use, often suffer from high working temperatures and limited sensitivity to H₂ gas, which presents significant challenges for their performance and application. This study addresses these issues by introducing a novel SnO₂-based sensor featuring a three-dimensional (3D) nanostructure, designed to enhance sensitivity and allow for room-temperature operation. This work lies in the use of a 3D anodic aluminum oxide (AAO) template to deposit SnO₂ nanoparticles through ultrasonic spray pyrolysis, followed by modification with platinum (Pt) nanoparticles to further enhance the sensor’s response. The as-prepared sensors were extensively characterized, and their H₂ sensing performance was evaluated. The results show that the 3D nanostructure provides a uniform and dense distribution of SnO₂ nanoparticles, which significantly improves the sensor’s sensitivity and repeatability, especially in H₂ detection at room temperature. This work demonstrates the potential of utilizing 3D nanostructures to overcome the traditional limitations of SnO₂-based sensors. Full article