Search Results (87,125)

Polyethylene terephthalate (PET) is a widely used polymer whose accumulation in the environment poses a significant pollution challenge. This study explores the degradation of bis(2-hydroxyethyl) terephthalate (BHET) and terephthalic acid (TPA)—two monomers commonly produced during PET hydrolysis and widely used as intermediates in PET recycling—through Advanced Oxidation Processes (AOPs) employing KrCl (222 nm) and XeBr (283 nm) excimer lamps in the presence of hydrogen peroxide (H₂O₂). The effects of the H₂O₂/monomer mass ratio, initial monomer concentrations, and reaction volume on degradation efficiency were systematically evaluated. The results demonstrate that excimer lamp technology, particularly KrCl, holds promising potential for the effective degradation of both BHET and TPA, and thus represents a viable strategy for PET waste treatment. Full article

Surface functionalization is key for tuning the electronic and magnetic properties essential in spintronics, yet its impact on chromium-based MXenes (Cr₃C₂T₂) is not fully understood. Using spin-polarized DFT+U, this study investigates how O, F, and OH groups modify the magnetic state, electronic structure, and Curie temperature. Functionalization dramatically changes magnetism: O termination gives ferromagnetism, while F and OH yield ferrimagnetism. Our results show surface functionalization effectively adjusts the Curie temperature, critical for spintronic materials. The electronic character is highly functional group dependent: pristine Cr₃C₂ is half-metallic, Cr₃C₂O₂ metallic, and Cr₃C₂F₂/Cr₃C₂(OH)₂ semiconducting with narrow gaps. Structures with dynamic stability are analyzed through phonon spectroscopy. These findings provide fundamental insights into controlling MXene properties via surface functionalization, guiding the design of next-generation spintronic materials. Full article

Silicone oil-based magnetic liquids containing carbon nanotubes (CNTs) were prepared using an in situ chemical coprecipitation method. The surface modification of Fe₃O₄/CNT composite particles was carried out by using three silane coupling agents: γ-aminopropyltriethoxysilane (550), γ-methacryloxypropyltrimethoxysilane (570), and phenyltrimethoxysilane (7030). Infrared Spectroscopy (IR), Transmission Electron Microscopy (TEM), and X-ray Diffraction (XRD) were used to confirm the successful doping of CNTs and the effective coating of the coupling agents. The rheological behavior of the magnetic liquids was systematically studied using an Anton Paar Rheometer. The results show that viscosity decreases exponentially with increasing temperature (fitting the Arrhenius equation), increases and tends to saturate with rising magnetic field intensity, and exhibits shear-thinning characteristics with increasing shear rate. Among the samples, Fe₃O₄@7030 has the best visco-thermal performance due to the benzene ring structure, which reduces the symmetry of the molecular chains. In contrast, Fe₃O₄@570 shows the most significant magneto-viscous effect (viscosity variation of 161.4%) as a result of the long-chain structure enhancing the steric hindrance of the magnetic dipoles. Full article

In the renewable energy conversion system, water electrolysis technology is widely regarded as the core means to achieve clean hydrogen production. However, the anodic oxygen evolution reaction (OER) has become a key bottleneck limiting the overall water splitting efficiency due to its slow kinetic process and high overpotential. This study proposes a novel Co₃O₄-TiO₂/CNTs p-n heterojunction catalyst, which was synthesized by hydrothermal method and significantly improved OER activity by combining heterojunction interface regulation and light field enhancement mechanism. Under illumination conditions, the catalyst achieved an overpotential of 390 mV at a current density of 10 mA cm⁻², which is superior to the performance of the dark state (410 mV) and single component Co₃O₄-TiO₂ catalysts. The material characterization results indicate that the p-n heterojunction structure effectively promotes the separation and migration of photogenerated carriers and enhances the visible light absorption capability. This work expands the design ideas of energy catalytic materials by constructing a collaborative electric light dual field regulation system, providing a new strategy for developing efficient and low-energy water splitting electrocatalysts, which is expected to play an important role in the future clean energy production and storage field. Full article

Introduction: The combination of ceftazidime−avibactam (CAZ-AVI) with aztreonam (ATM) may be an option for the treatment of infections due to metallo-β-lactamases (MBLs) producing bacteria, as recommended by current guidelines. MBLs protect the pathogen from any available β-lactam/β-lactamase inhibitor (BL/BLI). Moreover, in vitro and clinical data suggest that double carbapenem therapy (DCT) may be an option for such infections. Materials and Methods: This retrospective study was conducted in two mixed intensive care units (ICUs) at the University Hospital of Larissa, Thessaly, Greece, and the General Hospital of Larissa, Thessaly, Greece, during a three-year period (2022−2024). Mechanically ventilated patients with bloodstream infection (BSI) caused by K. pneumoniae resistant to all BL/BLI combinations were studied. Patients were divided into three groups: in the first, patients were treated with CAZ-AVI + ATM; in the second, with DCT; and in the third, with antibiotics other than BL/BLIs that presented in vitro susceptibility. The primary outcome of the study was the change in Sequential Organ Failure Assessment (SOFA) score between the onset of infection and the fourth day of antibiotic treatment. Secondary outcomes were SOFA score evolution during the treatment period, total duration of mechanical ventilation (MV), ICU length of stay (LOS), and ICU mortality. Results: A total of 95 patients were recruited. Among them, 23 patients received CAZ-AVI + AZT, 22 received DCT, and 50 patients received another antibiotic regimen which was in vitro active against the pathogen. The baseline characteristics were similar. The mean (SE) overall age was 63.2 (1.3) years. Mean (SE) Acute Physiology and Chronic Health Evaluation II (APACHE II) and SOFA scores were 16.3 (0.6) and 7.6 (0.3), respectively. The Charlson Index was similar between groups. The control group presented a statistically lower SOFA score on day 4 compared to the other two groups [mean (SE) 8.9 (1) vs. 7.4 (0.9) vs. 6.4 (0.5) for CAZ-AVI + ATM, DCT and control group, respectively (p = 0.045)]. The duration of mechanical ventilation, ICU LOS, and mortality were similar between the groups (p > 0.05). Comparison between survivors and non-survivors revealed that survivors had a lower SOFA score on the day of BSI, higher PaO₂/FiO₂ ratio, higher platelet counts, and lower lactate levels (p < 0.05). Septic shock was more frequent among non-survivors (60.3%) in comparison to survivors (27%) (p = 0.0015). Independent factors for mortality were PaO₂/FiO₂ ratio and lactate levels (p < 0.05). None of the antibiotic regimens received by the patients was independently associated with survival. Conclusions: Treatment with CAZ-AVI + ATM or DCT may offer similar clinical outcomes for patients suffering from BSI caused by K. pneumoniae strains resistant to all available BL/BLIs. However, larger studies are required to confirm the findings. Full article

Traditional forced-air cooling systems suffer from excessive energy consumption and noise pollution. This study proposes an innovative passive cooling strategy through developing aqueous radiative cooling coatings made from a combination of TiO₂-decorated carbon nanotube (TiO₂-CNT) hybrids and polyacrylic acid (PAA), designed to simultaneously enhance the heat dissipation and improve the mechanical strength of the coating films. Based on CNTs’ exceptional thermal conductivity and record-high infrared emissivity, bead-like TiO₂-CNT architectures have been prepared as the filler in PAA. The TiO₂ nanoparticles were in situ grown on CNTs, forming a rough surface that can produce asperity contacts and enhance the strength of the TiO₂-CNT/PAA composite. Moreover, this composite enhanced heat dissipation and achieved remarkable cooling efficiency at a small fraction of the filler (0.1 wt%). The optimized coating demonstrated a temperature reduction of 23.8 °C at an operation temperature of 180.7 °C, coupled with obvious mechanical reinforcement (tensile strength from 13.7 MPa of pure PAA to 17.1 MPa). This work achieves the combination of CNT and TiO₂ nanoparticles for strong radiative cooling coating, important for energy-efficient thermal management. Full article

A synthetic methodology of the CuAAC “click” approach was exploited for the construction of 1,2-azolyltriazole quinine derivatives by the reaction of O-propargylquinine with azidomethyl-1,2-azoles in methanol. Quinine–piperidine and quinine–anabasine conjugates were obtained using a chloroacetate linker by reacting quinine chloroacetate with piperidine or anabasine in a diethyl ether medium. Cinchophene ester was obtained by the acylation of quinine with cinchophen acid chloride in methylene chloride. The antibacterial, fungicidal, analgesic and cytotoxic properties of the obtained compounds were examined. Full article

This study presents a 39-year spatiotemporal analysis of shoreline variability at Topocalma Beach (Chile) using satellite-derived data collected between 1985 and 2024. A total of 350 satellite images were processed with CoastSat and DSAS v6.0 to quantify erosional and accretional trends across distinct beach sectors. The results show persistent erosion in the proximal zone near the Topocalma wetland and localized accretion in the distal (southern) segment. These changes are closely associated with the 2010 Maule earthquake and tsunami, strong ENSO phases, and an increase in storm surge activity since 2015. The spatiotemporal beach width model reveals distinct phases of retreat and short-term post-seismic stabilization, followed by a shift to sustained erosion. Overall, this study underscores the limited natural recovery capacity of the beach and highlights the utility of satellite-based monitoring tools for coastal resilience planning in data-limited regions. Full article

Virtual AI-driven streamers have been gradually used in live commerce, and they may affect consumer impulsive purchase intention. Drawing on the stimulus–organism–response (S-O-R) model, this research examined consumer impulsive purchase intention in virtual AI streaming. Based on survey data from 411 predominantly young and educated virtual AI streaming users recruited through snowball sampling, we found that perceived responsiveness, perceived likeability, perceived expertise, and perceived anthropomorphism of virtual AI streamers are associated with trust and flow experience, both of which predict consumers’ impulsive purchase intentions. The fsQCA identified two paths that lead to impulsive purchase intention. The results imply that live streaming platforms need to engender consumers’ trust and flow experience in order to increase their impulsive purchase intention. Full article

Electrospun nanofibrous membranes have gained considerable attention in bone tissue engineering due to their ability to mimic the extracellular matrix and provide a suitable environment for cell attachment and proliferation. This study investigates the fabrication, characterization, and biocompatibility of poly(L-lactic acid) (PLA)-based membranes enhanced with periclase (MgO) and gold nanoparticles (AuNPs). The membranes were fabricated using an optimized electrospinning process and subsequently characterized using scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), Fourier-transform infrared spectroscopy (FT-IR), and contact angle measurements. Additionally, in vitro biodegradation studies in simulated body fluid (SBF) and cytocompatibility tests with osteoblast-like cells were conducted. The results demonstrated that the incorporation of MgO and AuNPs significantly influenced the structural and chemical properties of the membranes, improving their wettability and bioactivity. SEM imaging confirmed uniform fiber morphology with well-distributed nanoparticles. FT-IR spectroscopy indicated successful integration of bioactive components into the PLA matrix. Cytocompatibility assays showed that modified membranes promoted higher osteoblast adhesion and proliferation compared to pristine PLA membranes. Furthermore, biodegradation studies revealed a controlled degradation rate suitable for guided bone regeneration applications. These findings suggest that electrospun PLA membranes enriched with MgO and AuNPs present a promising biomaterial for GBR applications, offering improved bioactivity, mechanical stability, and biocompatibility. Full article

This study developed a new magnetic adsorbent from waste coconut shells using high-temperature carbonization, EDTA-2Na chelation, and Fe₃O₄ magnetic loading. Response surface methodology optimized the preparation conditions to a mass ratio of activated carbon: EDTA-2Na:Fe₃O₄ = 2:0.6:0.2. Characterization (SEM, XRD, FT-IR, and EDS) showed that EDTA-2Na increased the surface carboxyl and amino group density, while Fe₃O₄ loading (Fe concentration 6.83%) provided superior magnetic separation performance. The optimal adsorption conditions of Cu²⁺ by EDTA-2Na-Fe₃O₄-activated carbon composite material are as follows: when pH = 5.0 and the initial concentration is 180 mg/L, the equilibrium adsorption capacity reaches 174.96 mg/g, and the removal rate reaches 97.2%. The optimal adsorption conditions for Pb²⁺ are as follows: when pH = 6.0 and the initial concentration is 160 mg/L, the equilibrium adsorption capacity reaches 157.60 mg/g, and the removal rate reaches 98.5%. The optimal adsorption conditions for Cd²⁺ are pH = 8.0 and an initial concentration of 20 mg/L. The equilibrium adsorption capacity reaches 18.76 mg/g, and the removal rate reaches 93.8%. The adsorption followed the pseudo-second-order kinetics (R² > 0.95) and Langmuir/Freundlich isotherm models, indicating chemisorption dominance. Desorption experiments using 0.1 mol/L HCl and EDTA-2Na achieved efficient desorption (>85%), and the material retained over 80% of its adsorption capacity after five cycles. This cost-effective and sustainable adsorbent offers a promising solution for heavy metal wastewater treatment. Full article

Improving charge transport in the aggregated state of nanocomposites is challenging due to the large number of defects present at grain boundaries. To enhance the charge transfer and photogenerated carrier extraction of MnO_x nanofibers, a MnO_x/GO (graphene oxide) nanocomposite was prepared. The effects of GO content and bias on the optoelectronic properties were studied. Representative light sources at 405, 650, 780, 808, 980, and 1064 nm were used to examine the photoelectric signals. The results indicate that the MnO_x/GO nanocomposites have photocurrent switching behaviours from the visible region to the NIR (near-infrared) when the amount of GO added is optimised. It was also found that even with zero bias and storage of the nanocomposite sample at room temperature for over 8 years, a good photoelectric signal could still be extracted. This demonstrates that the MnO_x/GO nanocomposites present a strong built-in electric field that drives the directional motion of photogenerated carriers, avoids the photogenerated carrier recombination, and reflect a good photophysical stability. The strength of the built-in electric field is strongly affected by the component ratios of the resulting nanocomposite. The formation of the built-in electric field results from interfacial charge transfer in the nanocomposite. Modulating the charge behaviour of nanocomposites can significantly improve the physicochemical properties of materials when excited by light with different wavelengths and can be used in multidisciplinary applications. Since the recombination of photogenerated electron–hole pairs is the key bottleneck in multidisciplinary fields, this study provides a simple, low-cost method of tailoring defects at grain boundaries in the aggregated state of nanocomposites. These results can be used as a reference for multidisciplinary fields with low energy consumption. Full article

In this study, the impact of moderate and high CO₂ and O₂ levels was compared to low and moderate gas combinations during prolonged storage on the quality of Regina sweet cherries harvested in different maturity stages, particularly in terms of decreasing internal browning. Fruits were harvested in two different maturity stages (Light and Dark Mahogany skin color) and stored in CA of 15% CO₂ + 10% O₂; 10% CO₂ + 10% O₂; 10% CO₂ + 5% O₂; 5% CO₂ + 5% O₂ and MA of 4 to 5% CO₂ + 16 to 17% O₂ for 30 and 40 days at 0 °C and 90% RH, followed by a marketing period. After the storage, both maturity stages significantly reduced internal browning, decay, and visual quality losses in CA with 10–15% CO₂ and 10% O₂. In addition, it preserved luminosity, total soluble solids (TSSs), titratable acidity (TA), and bioactive compounds such as anthocyanins and phenols. This treatment also maintained the visual appearance of the sweet cherries, favoring their market acceptance. At the same time, the light red fruits showed a better general quality compared to darker color after the storage. In conclusion, a controlled atmosphere with optimized CO₂ and O₂ concentrations, together with harvesting with a Light Mahogany external color, represents an effective strategy to extend the shelf life of Regina sweet cherries up to 40 days plus the marketing period, maintaining their physical and sensory quality for export markets. Full article

2,5-bis(hydroxymethy)lfuran (BHMF), a renewable compound with extensive industrial applications, can be obtained by selective hydrogenation of the C=O group of 5-hydroxymethylfurfural (HMF), a platform molecule derived from lignocellulosic biomass. In this work, we perform kinetic modeling of the selective liquid-phase hydrogenation of HMF to BHMF over a Cu/SiO₂ catalyst prepared by precipitation–deposition (PD) at a constant pH. Physicochemical characterization, using different techniques, confirms that the Cu/SiO₂–PD catalyst is formed by copper metallic nanoparticles of 3–5 nm in size highly dispersed on the SiO₂ surface. Before the kinetic study, the Cu/SiO₂-PD catalyst was evaluated in three solvents: tetrahydrofuran (THF), 2-propanol (2-POH), and water. The pattern of catalytic activity and BHMF yield for the different solvents was THF > 2-POH > H₂O. In addition, selectivity to BHF was the highest in THF. Thus, THF was chosen for further kinetic study. Several experiments were carried out by varying the initial HMF concentration (C⁰_HMF) between 0.02 and 0.26 M and the hydrogen pressure (P_H2) between 200 and 1500 kPa. In all experiments, BHMF selectivity was 97–99%. By pseudo-homogeneous modeling, an apparent reaction order with respect to HFM close to 1 was estimated for a C⁰_HMF between 0.02 M and 0.065 M, while when higher than 0.065 M, the apparent reaction order changed to 0. The apparent reaction order with respect to H₂ was nearly 0 when C⁰_HMF = 0.13 M, while for C⁰_HMF = 0.04 M, it was close to 1. The reaction orders estimated suggest that HMF is strongly absorbed on the catalyst surface, and thus total active site coverage is reached when the C⁰_HMF is higher than 0.065 M. Several Langmuir–Hinshelwood–Hougen–Watson (LHHW) kinetic models were proposed, tested against experimental data, and statistically compared. The best fitting of the experimental data was obtained with an LHHW model that considered non-competitive H₂ and HMF chemisorption and strong chemisorption of reactant and product molecules on copper metallic active sites. This model predicts both the catalytic performance of Cu/SiO₂-PD and its deactivation during liquid-phase HMF hydrogenation. Full article

This work analyzes the aero-elastic oscillations of cantilever beams reinforced by carbon nanotubes (CNTs). Four different distributions of single-walled CNTs are assumed as the reinforcing phase, in the thickness direction of the polymeric matrix. A modified third-order piston theory is used as an accurate tool to model the supersonic air flow, rather than a first-order piston theory. The nonlinear dynamic equation governing the problem accounts for Von Kármán-type nonlinearities, and it is derived from Hamilton’s principle. Then, the Galerkin decomposition technique is adopted to discretize the nonlinear partial differential equation into a nonlinear ordinary differential equation. This is solved analytically according to a multiple time scale method. A comprehensive parametric analysis was conducted to assess the influence of CNT volume fraction, beam slenderness, Mach number, and thickness ratio on the fundamental frequency and lateral dynamic deflection. Results indicate that FG-X reinforcement yields the highest frequency response and lateral deflection, followed by UD and FG-A patterns, whereas FG-O consistently exhibits the lowest performance metrics. An increase in CNT volume fraction and a reduction in slenderness ratio enhance the system’s stiffness and frequency response up to a critical threshold, beyond which a damped beating phenomenon emerges. Moreover, higher Mach numbers and greater thickness ratios significantly amplify both frequency response and lateral deflections, although damping rates tend to decrease. These findings provide valuable insights into the optimization of CNTR composite structures for advanced aeroelastic applications under supersonic conditions, as useful for many engineering applications. Full article