Search Results (72)

To tackle challenges including excessive initial boiling superheat and low heat transfer coefficients inherent in conventional working fluids, hydrophobic-modified TiO₂@carbon nanotube (MWCNT) composite nanofluids were fabricated. Subsequently, the boiling heat transfer mechanisms were systematically investigated and visually verified. Hydrophobic TiO₂ nanofluids exhibit enhanced stability, whereas hydrophobic TiO₂@MWCNTs composite nanofluids demonstrate improved thermal conductivity. At a mass ratio of hydrophobic-modified TiO₂ to MWCNTs of 2:1, the optimal heat transfer performance was attained, with a 31.6% increase in heat transfer coefficient (HTC) and a 46.5% increase in critical heat flux (CHF) density relative to hydrophobic-modified TiO₂ nanofluids. Composite nanofluids exert effective regulation over bubble kinetic parameters: hydrophobic nanoparticles increase vaporization core density, reduce bubble nucleation energy barriers, and mitigate initial boiling superheat. Benefiting from the superior thermal conductivity and mechanical properties, MWCNTs remarkably promote heat transfer efficiency. The synergistic effect between the two components enables the concurrent enhancement of HTC and CHF, thus highlighting the promising application potential of hydrophobic-modified TiO₂@MWCNTs composite nanofluids in intensifying pool boiling heat transfer. Full article

The rapid advancement of humanoid robotics has spurred researchers’ interest in flexible sensors for wide linear range detection. In response, we report a capacitive flexible pressure sensor based on a multi-walled carbon nanotubes/titanium dioxide/polydimethylsiloxane (MWCNTs/TiO₂/PDMS) composite. A micro-hemispherical structure array formed on the composite surface via a templating method reduces the initial capacitance value. Modified carbon nanotubes (F-MWCNTs) were prepared using 2 wt%, 5 wt% and 10 wt% γ-aminopropyltriethoxysilane (APTES), significantly enhancing dispersion and interfacial bonding strength. The synergistic effect of microstructures and MWCNTs surface functionalization further enhances sensing performance. The F-MWCNTs/TiO₂/PDMS pressure sensor modified with 2 wt% APTES exhibits outstanding sensing capabilities: it demonstrates dual-stage sensitivity across a broad linear range of 0–95 kPa (0–13 kPa segment: 1.89 ± 0.49 kPa⁻¹; 13–95 kPa segment: 7.08 ± 0.63 kPa⁻¹), with a response time of 200 milliseconds, maintaining stability over 2500 cyclic loadings. In practical application exploration, this sensor has demonstrated strong adaptability, confirming its significant potential in micro-pressure detection, wearable electronics, and array sensing applications. Full article

In this work, pCh-MWCNTs@Ag-TiO₂/S and pCh-MWCNTs@Ag-TiO₂ nanocomposites were synthesized through a combined phosphorylation and cross-linked polymerization method. The materials were thoroughly characterized using several analytical techniques, including SEM/EDS, FTIR, TGA, and BET analysis. SEM images revealed that the pCh-MWCNTs@Ag-TiO₂/S nanocomposite displayed a smooth, flake-like morphology with spherical, dark greenish particles. EDS analysis confirmed the presence of Si, S, P, and Ag as prominent elements, with Ti, C, and O showing the most intense peaks. The TGA curves indicated significant weight loss between 250–610 °C for pCh-MWCNTs@Ag-TiO₂ and 210–630 °C for pCh-MWCNTs@Ag-TiO₂/S, corresponding to the decomposition of organic components. FTIR spectra validated the existence of functional groups such as hydroxyl (-OH), carboxyl (-COOH), and carbonyl (-C=O) on the surface of the nanocomposites. Following characterization, the materials were evaluated for their capacity to adsorb Hg²⁺ at parts-per-billion (ppb) concentrations in contaminated water. Batch adsorption experiments identified optimal conditions for mercury removal. For pCh-MWCNTs@Ag-TiO₂, the best performance was observed at pH 4, with an adsorbent dose of 4.0 mg, initial mercury concentration of 16 ppb, and a contact time of 90 min. For pCh-MWCNTs@Ag-TiO₂/S, optimal conditions were at pH 6, a dosage of 3.5 mg, the same initial concentration, and a contact time of 100 min. Each parameter was optimized to determine the most effective conditions for Hg²⁺ removal. The nanocomposites showed high efficiency, achieving more than 95% mercury removal under these conditions. Kinetic studies indicated that the adsorption process followed a pseudo-second-order model, while the equilibrium data aligned best with the Langmuir isotherm, suggesting monolayer adsorption behavior. Overall, this research highlights the effectiveness of sulfur-modified chitosan-based nanocomposites as eco-friendly and efficient adsorbents for the removal of mercury from aqueous systems, offering a promising solution for water purification and environmental protection. Full article

This research investigates the multi-objective optimization of micro-milling processes for the titanium alloy Ti-3Al-2.5V (grade 9) through the application of grey relational analysis. The incorporation of nanometer-sized particles in hybrid machining lubricants plays a crucial role in improving heat transfer during machining. The approach aims to increase the efficiency and effectiveness of micro-milling by addressing various performance metrics simultaneously, leading to better machining results for this titanium alloy. Additionally, the integration of nanoparticles into the machining lubricant significantly improves the lubrication properties, reducing friction during the machining process. The study analyzed four machining parameters: machining speed, rate of feed, axial depth of cut, and the weight percentage concentration of hybrid machining lubricants Multi-wall Carbon Nano Tube and Alumina Oxide (MWCNT and Al₂O₃). The machining nanolubricant was formulated by adding 1% and 2% volume concentrations of MWCNT and Al₂O₃ nanoparticles to the industrial machining fluid. In this machining context, the friction between the machining tool and the Ti-3Al-2.5V work piece is a vital factor influencing the output quality. The results demonstrate that the chosen machining parameters and machining lubricants have a direct impact on the coefficient of friction and surface roughness. The study concludes that utilizing machining nanolubrication for machining Ti-3Al-2.5V (grade 9) significantly enhances the quality compared with traditional machining lubricants. Full article

Endocytic uptake and lysosomal localization are suggested to be the key mechanisms underlying the toxicity of metal oxide nanoparticles (MONPs), with dissolution in the acidic milieu driving the response. In this study, we aimed to investigate if MONPs of varying solubility are similarly sequestered intracellularly, including in lysosomes and the role of the acidic lysosomal milieu on toxicity induced by copper oxide (CuO) nanoparticles (NPs), nickel oxide (NiO) NPs, aluminum oxide (Al₂O₃) NPs, and titanium dioxide (TiO₂) NPs of varying solubility in FE1 lung epithelial cells. Mitsui-7 multi-walled carbon nanotubes (MWCNTs) served as contrasts against particles. Enhanced darkfield hyperspectral imaging (EDF-HSI) with fluorescence microscopy was used to determine their potential association with lysosomes. The v-ATPase inhibitor Bafilomycin A1 (BaFA1) was used to assess the role of lysosomal acidification on toxicity. The results showed co-localization of all MONPs with lysosomes, with insoluble TiO₂ NPs showing the greatest co-localization. However, only acute toxicity induced by soluble CuO NPs was affected by the presence of BaFA1, showing a 14% improvement in relative survival. In addition, all MONPs were found to be associated with large actin aggregates; however, treatment with insoluble TiO₂ NPs, but not soluble CuO NPs, impaired the organization of F-actin and α-tubulin. These results indicate that MONPs are sequestered similarly intracellularly; however, the nature or magnitude of their toxicity is not similarly impacted by it. Future studies involving a broader variety of NPs are needed to fully understand the role of differential sequestration of NPs on cellular toxicity. Full article

Nanoparticle additives are used to increase the cooling efficiency of cutting fluids in machining. In this study, changing dynamic viscosity values depending on the addition of nanoparticles to cutting oils was investigated. Mono nanofluids were prepared by adding hBN (hexagonal boron nitride), ZnO, MWCNT (multi-walled carbon nanotube), TiO₂, and Al₂O₃ as nanoparticles, hybrid nanofluids were prepared by using two types of nanoparticles (ZnO + MWCNT, hBN + MWCNT etc.), and ternary nanofluids were prepared by using three types of nanoparticles. GPR (Gaussian process regression) was used to estimate unmeasured dynamic viscosity values using the dynamic viscosity values measured for different temperatures. Dynamic viscosity results are a precise determination (R² = 1). An augmented dataset was obtained by adding the dynamic viscosity values estimated with high accuracy. A fitness function based on dynamic viscosity and nanoparticle unit costs was proposed for the cost analysis. With the help of the proposed fitness function, it was observed that the best performing nanoparticles were the ZnO and ZnO hybrid mixtures according to different dynamic viscosity and cost effects. The study showed that the most suitable nanofluid selection focused on performance and cost could be made without performing experiments under various operating conditions by increasing the limited experimental measurements with strong GPR estimates and using the proposed fitness function. Full article

Machining processes often face challenges such as elevated temperatures and wear, which traditional cutting fluids are insufficient to address. As a result, solutions involving nanoparticle additives are being explored to enhance cooling and lubrication performance. This study investigates the effect of thermal conductivity, an important property influenced by the densities of mono and hybrid nanofluids. To this end, various nanofluids were prepared by incorporating hexagonal boron nitride (hBN), zinc oxide (ZnO), multi-walled carbon nanotubes (MWCNTs), titanium dioxide (TiO₂), and aluminum oxide (Al₂O₃) nanoparticles into sunflower oil as the base fluid. Hybrid nanofluids were created by combining two nanoparticles, including ZnO + MWCNT, hBN + MWCNT, hBN + ZnO, hBN + TiO₂, hBN + Al₂O₃, and TiO₂ + Al₂O₃. A dataset consisting of 180 data points was generated by measuring the thermal conductivity and density of the prepared nanofluids at various temperatures (30–70 °C) in a laboratory setting. Conducting thermal conductivity measurements across different temperature ranges presents significant challenges, requiring considerable time and resources, and often resulting in high costs and potential inaccuracies. To address these issues, a feedforward artificial neural network (FFANN) method was proposed to predict thermal conductivity. Our multilayer FFANN model takes as input the temperature of the experimental environment where the measurement is made, the measured thermal conductivity of the relevant nanoparticle, and the relative density of the nanoparticle. The FFANN model predicts the thermal conductivity value linearly as output. The model demonstrated high predictive accuracy, with a reliability of R = 0.99628 and a coefficient of determination (R²) of 0.9999. The average mean absolute error (MAE) for all hybrid nanofluids was 0.001, and the mean squared error (MSE) was 1.76 × 10⁻⁶. The proposed FFANN model provides a State-of-the-Art approach for predicting thermal conductivity, offering valuable insights into selecting optimal hybrid nanofluids based on thermal conductivity values and nanoparticle density. Full article

Cobalt ferrite (CoFe₂O₄) combined with multi-walled carbon nanotubes (MWCNTs) is an outstanding material regarding photoelectrochemical water oxidation (PEC-WO) because of its excellent catalytic properties and stability. On the other hand, surface imperfections in CoFe₂O₄ can cause band bending and surface Fermi level pinning, significantly reducing its PEC conversion efficiency. Heterostructure engineering is essential for achieving increased light-gathering capacity and charge separation efficiency for PEC-WO. In this study, a quaternary heterostructure of CoFe₂O₄/MWCNT-doped Metal–Organic Framework-100 (Iron), MIL-100(Fe)/Titanium Oxide (TiO₂) was synthesized by using a combination of hydrothermal, solvothermal, and “dip and dry” techniques. Characterization results confirmed the formation of a structural network of MIL-100(Fe) on TiO₂ surfaces, enhanced by the incorporation of MWCNTs during the hydrothermal reaction. Under 1 sun irradiation, the resultant quaternary heterostructure displayed a photocurrent density (J_ph) of 3.70 mA cm⁻² under free bias voltage, which is around 3.08 times more than that of pristine TiO₂ photoanodes (J_ph = 1.20 mA cm⁻²). This investigation highlights the advantages of the MIL-100(Fe) network in improving the solar PEC-WO performance of TiO₂ photoanodes. Full article

The field of nanotechnology has experienced exponential growth, with the unique properties of nanomaterials (NMs) being employed to enhance a wide range of products across diverse industrial sectors. This study examines the toxicity of metal- and carbon-based NMs, with a particular focus on titanium dioxide (TiO₂), zinc oxide (ZnO), silica (SiO₂), cerium oxide (CeO₂), silver (Ag), and multi-walled carbon nanotubes (MWCNTs). The potential health risks associated with increased human exposure to these NMs and their effect on the respiratory, gastrointestinal, dermal, and immune systems were evaluated using in vitro assays. Physicochemical characterisation of the NMs was carried out, and in vitro assays were performed to assess the cytotoxicity, genotoxicity, reactive oxygen species (ROS) production, apoptosis/necrosis, and inflammation in cell lines representative of the systems evaluated (3T3, Caco-2, HepG2, A549, and THP-1 cell lines). The results obtained show that 3T3 and A549 cells exhibit high cytotoxicity and ROS production after exposure to ZnO NMs. Caco-2 and HepG2 cell lines show cytotoxicity when exposed to ZnO and Ag NMs and oxidative stress induced by SiO₂ and MWCNTs. THP-1 cell line shows increased cytotoxicity and a pro-inflammatory response upon exposure to SiO₂. This study emphasises the importance of conducting comprehensive toxicological assessments of NMs given their physicochemical interactions with biological systems. Therefore, it is of key importance to develop robust and specific methodologies for the assessment of their potential health risks. Full article

Two ranges of dielectric permittivity (k) increase in polymer composites upon the modification of BaTiO₃ filler with multiwalled carbon nanotubes (MWCNTs) are shown for the first time. The first increase in permittivity is observed at low MWCNT content in the composite (approximately 0.07 vol.%) without a considerable increase in dielectric loss tangent and electrical conductivity. This effect is determined by the intensification of filler–polymer interactions caused by the nanotubes, which introduce Brønsted acidic centers on the modified filler surface and thus promote interactions with the cyanoethyl ester of polyvinyl alcohol (CEPVA) polymer binder. Consequently, the structure of the composites becomes more uniform: the permittivity increase is accompanied by a decrease in the lacunarity (nonuniformity) of the structure and an increase in scale invariance, which characterizes the self-similarity of the composite structure. The permittivity of the composites in the first range follows a modified Lichtenecker equation, including the content of Brønsted acidic centers as a parameter. The second permittivity growth range features a drastic increase in the dielectric loss tangent and conductivity corresponding to the percolation effect with the threshold at 0.3 vol.% of MWCNTs. Full article

Dye-sensitized solar cells (DSSCs) have attracted renewed research interest as a potential low-cost substitute for conventional silicon photovoltaics. This work aims to improve the photovoltaic performance of the DSSCs by incorporating multi-walled carbon nanotubes (MWCNTs) into the BaTiO₃ photoelectrode. The pure BaTiO₃ and BaTiO₃/MWCNT nanocomposites were sensitized with N719 dye and fabricated into solar cell devices for testing. The structural characterization confirmed the successful formation of the nanocomposite with an optimal dispersion at 6% of MWCNT incorporation, beyond which agglomeration effects manifested. The optical analysis verified the modulation of defect states and bandgap engineering induced by the MWCNT network. The morphological studies revealed irregular nanoparticle clusters with embedded nanotubes. Solar cell testing under AM1.5G-simulated sunlight demonstrated a peak power conversion efficiency of 4.044% for 6% of MWCNT doping, constituting a 6-fold increment versus pure BaTiO₃ (0.693%). It originated from the simultaneous enhancements in the open-circuit voltage and short-circuit current enabled by the favorable band structure alterations and percolation-assisted charge transport. However, further increasing MWCNT content deteriorated the device metrics, owing to emerging limitations like trapping. The rational integration of multi-walled carbon nanotubes with lead-free ferroelectric metal oxides can contribute to the development of emerging organic-inorganic hybrid solar platforms. Full article

Hydrogen peroxide (H₂O₂) is a signaling molecule that has the capacity to control a variety of biological processes in organisms. Cancer cells release more H₂O₂ during abnormal tumor growth. There has been a considerable amount of interest in utilizing H₂O₂ as a biomarker for the diagnosis of cancer tissue. In this study, an electrochemical sensor for H₂O₂ was constructed based on 3D reduced graphene oxide (rGO), MXene (Ti₃C₂), and multi-walled carbon nanotubes (MWCNTs) composite. Three-dimensional (3D) rGO–Ti₃C₂–MWCNTs sensor showed good linearity for H₂O₂ in the ranges of 1–60 μM and 60 μM–9.77 mM at a working potential of −0.25 V, with sensitivities of 235.2 µA mM⁻¹ cm⁻² and 103.8 µA mM⁻¹ cm⁻², respectively, and a detection limit of 0.3 µM (S/N = 3). The sensor exhibited long-term stability, good repeatability, and outstanding immunity to interference. In addition, the modified electrode was employed to detect real-time H₂O₂ release from cancer cells and cancer tissue ex vivo. Full article

A complex study of the adhesion of multi-walled carbon nanotubes to a titanium surface, depending on the modes of irradiation with He⁺ ions of the “MWCNT/Ti” system, was conducted using atomic force microscopy and X-ray photoelectron spectroscopy. A quantitative assessment of the adhesion force at the interface, performed using atomic force microscopy, demonstrated its significant increase as a result of treatment of the “MWCNT/Ti” system with a beam of helium ions. The nature of the chemical bonding between multi-walled carbon nanotubes and the surface of the titanium substrate, which causes this increase in the adhesion of nanotubes to titanium as a result of ion irradiation, was investigated by X-ray photoelectron spectroscopy. It was established that this bonding is the result of the formation of chemical C–O–Ti bonds between titanium and carbon atoms with the participation of oxygen atoms of oxygen-containing functional groups, which are localized on defects in the nanotube walls formed during ion irradiation. It is significant that there are no signs of direct bonding between titanium and carbon atoms. Full article

The demand for an improvement in the tribological properties of lubricants used in various industrial plants, the automotive industry, and other power transmissions has resulted in the development of a whole family of improved lubricants based on nanotechnology. Especially important are nanotube additives, which significantly improve the tribological properties of lubricants, primarily by reducing the friction coefficient and wear of the coupled elements but also by reducing the temperature load and increasing the stability of the oil film between the lubricated surfaces. The properties of nanotube-based additives were further improved using elements such as metal oxides and compounds based on titanium, molybdenum, aluminum, etc. This paper presents the results obtained in the field of research and application of nanocomposite lubricant additives. It also gives a partial comparative analysis of the research conducted in this field. The primary goal of this paper is to analyze the research results in the field of the application of nanotubes in lubricants and to indicate the importance of their application, such as improving the tribological properties of machines and reducing power losses. Furthermore, this paper shows the negative impact of nanoparticles on the environment and human health and the costs of applying some types of nanoparticles. Full article