Search Results (28)

This paper aims to design and optimize a new type of Darrieus H-Rotor VAWT, specifically adapted to the conditions of urban and industrial environments, as a contribution to energy transition and the search for new sustainable solutions for decentralized electricity generation. It is designed to be a strong and efficient wind turbine capable of providing a nominal power of 2 kW at low and moderate wind speed. The methodology used is based on the analysis of wind resources (wind rose, Weibull distribution) and aerodynamic modelling using QBlade. The structural analysis with CATIA showed that the configuration of the third case (with 4 mm blade thickness and four supports of 2 mm) was an excellent compromise, with a reduced mass (13 kg) and a controlled maximum stress (0.854 MPa), far below the elastic limit of aluminum. From an aerodynamic point of view, CFD simulations in ANSYS Fluent 2023 R1 (k-ω SST model in transient regime) allowed us to visualize flow fields, pressure distribution and torque evolution. The results obtained showed a power coefficient (Cp) very close to 0.4, validating the configuration. This proves the chosen configuration to be effective. In this work, a suitable wind blade has been optimized with a strong and aerodynamically efficient design for operation in urban areas. Full article

Small-scale vertical-axis wind turbines (VAWTs) are increasingly essential for the “blue economy,” providing autonomous power to remote coastal communities, offshore platforms, and marine industries. However, the design of efficient Darrieus-type rotors is complicated by complex unsteady aerodynamics, particularly the phenomenon of dynamic stall. This study aims to establish and validate a cost-effective yet accurate mathematical modeling approach for simulating unsteady turbulent flow around a Darrieus H-rotor to support practical engineering applications. The research methodology integrates computational fluid dynamics (CFD) with physical experiments in a hydrodynamic channel. The numerical model utilizes the unsteady Reynolds-averaged Navier–Stokes (URANS) equations closed with the Strain-Adaptive Linear Spalart–Allmaras (SALSA) turbulence model, chosen for its efficiency in capturing flow separation. The system of initial equations was being devised relatively to an arbitrary curvilinear coordinate system. The pressure and velocity fields have been coordinated using the artificial compressibility method adapted to calculate non-stationary problems. Experimental verification was conducted in the GT-400 hydrodynamic tube using a three-bladed H-rotor model, where flow structures were visualized via the colored jet method at tip speed ratios λ ranging from 2 to 5 and Reynolds number 1470. The findings reveal that dynamic stall occurs over a significant portion of the blade trajectory, characterized by vortex generation at the leading edge and subsequent advection along the chord. Qualitative comparison demonstrates a high degree of correlation between the calculated vortex dynamics and physical flow spectra. These results confirm that the URANS-SALSA approach provides a rational compromise between computational cost and physical accuracy. Full article

The integration of wind energy into urban environments is constrained by low wind speeds, high turbulence, and the recurrent negative torque experienced by lift-driven vertical-axis wind turbines (VAWTs). This study specifically evaluates a straight-bladed H-Darrieus rotor equipped with a single upstream passive flat-plate deflector for the wind regime measured on the campus of the Universidad Nacional Mayor de San Marcos (Lima, Peru). A three-dimensional transient CFD model using the SST k–ω turbulence model was applied to compare the baseline rotor and the deflector-assisted configuration under identical operating conditions; DMST calculations were used only as a low-order cross-check for the bare rotor performance trend, not as a substitute for experimental validation. The deflector was selected after a geometric sensitivity assessment and positioned at 30° relative to the incoming flow, with a span equal to the rotor height and a length comparable to the rotor diameter. At TSR = 2.5, the maximum power coefficient increased from 0.4459 for the bare rotor to 0.6153 with the deflector, equivalent to an improvement of approximately 38%. Velocity and pressure fields show that the deflector accelerates the flow toward the advancing blade while shielding the returning blade, thereby reducing adverse torque and smoothing cyclic torque fluctuations. The results define the applicability of the proposed passive device for low-to-moderate urban wind environments with a dominant wind sector and provide a reproducible numerical basis for subsequent wind-tunnel and field validation. Full article

Vertical axis wind turbines (VAWTs) have regained attention for distributed, urban, and floating offshore applications, yet the literature remains fragmented across competing rotor concepts and modelling traditions. This review consolidates the principal archetypes—Savonius, H-Darrieus, troposkein Darrieus, helical Darrieus, and Savonius–Darrieus hybrids—through five governing parameters: drag-versus-lift-driven operating principle, tip speed ratio $\mathsf{\lambda }=\mathsf{\omega }\mathrm{R}/{\mathrm{V}}_{\infty }$ (0.6–1.2 for Savonius; 2.5–5.0 for Darrieus), solidity $\mathsf{\sigma }=\mathrm{N}\mathrm{c}/\mathrm{R}$ (0.1–0.4), chord-based Reynolds number ${\mathrm{R}}_{\mathrm{e}\_\mathrm{c}}$ (${10}^5–{10}^6$), and peak power coefficient ${\mathrm{C}}_{\mathrm{p}\_\mathrm{m}\mathrm{a}\mathrm{x}}$ (0.15–0.25 for Savonius; 0.35–0.45 for optimized H-Darrieus). Off-design performance is dominated by unsteady mechanisms that quasi-steady streamtube models cannot resolve—leading edge vortex shedding, dynamic stall hysteresis, blade–wake interaction, and flow-curvature-induced virtual camber—each examined for its contribution to the instantaneous torque ${\mathrm{C}}_{\mathrm{T}}\left(\mathsf{\theta }\right)$ and the cycle-averaged ${\mathrm{C}}_{\mathrm{p}}$. Turbulence closures are benchmarked against phase-locked PIV and torque measurements: $\mathrm{k}–\mathsf{\omega }\mathrm{S}\mathrm{S}\mathrm{T}$ URANS captures peak-region ${\mathrm{C}}_{\mathrm{p}}$ to within $\pm 5–10\%$ but over-predicts torque below ${\mathsf{\lambda }}_{\mathrm{o}\mathrm{p}\mathrm{t}}$; the $\mathsf{\gamma }–{\mathrm{R}}_{\mathrm{e}\_\mathsf{\theta }}$ transition SST model reduces this error to $\pm 3–5\%$; DES, DDES, and LES reach $\pm 2–3\%$ at one to two orders of magnitude higher cost. Best practice computational fluid dynamics (CFD) guidelines are consolidated: domain extents of 15D upstream, 10D downstream, and 20D lateral; rotating sub-domain ${\mathrm{D}}_{\mathrm{r}\mathrm{o}\mathrm{t}}$ $\approx 1.5\mathrm{D}$; ${\mathrm{y}}^{+}\le 1$; $\Delta \mathsf{\theta }\le 0.1°$; and 20–30 revolutions before sampling. Performance enhancement strategies (variable pitch, guide vanes, helical twist, and hybridization) are reviewed quantitatively, with reported ${\mathrm{C}}_{\mathrm{p}}$ gains of $5–30\%$. Four research priorities are identified: (i) transition-sensitive turbulence closures validated below ${\mathrm{R}}_{\mathrm{e}\_\mathrm{c}}$ = $5\times {10}^5$; (ii) coupled aero-hydro-servo-elastic models for floating offshore VAWTs; (iii) machine-learning-augmented turbulence modelling—including physics-informed neural networks (PINNs) and neural-network-corrected RANS closures—to improve unsteady flow prediction at sub-LES cost; and (iv) integrated aeroacoustic–aeroelastic frameworks for urban and building-integrated deployment. Full article

The limited self-starting capability of H-type Darrieus Vertical-Axis Wind Turbines (VAWT) remains one of the main obstacles to their deployment in low-power and urban applications, where wind conditions are typically weak and intermittent. Although several passive geometric modification strategies have been proposed to enhance initial torque generation, most available studies rely predominantly on numerical simulations, with limited systematic experimental validation under low tip-speed ratio (TSR) conditions. In this work, the influence of passive blade modifications on self-starting performance is assessed through a combined numerical–experimental approach. An integrated numerical–experimental framework was used to systematically compare passive blade configurations under equivalent low-wind conditions. Two modified configurations, a biomimetic profile incorporating passive trailing-edge devices and an asymmetric J-type geometry, were optimized using transient CFD simulations of the first rotation cycle and a Design of Experiments (DOE) framework. Additively manufactured full-rotor test blades were then manufactured via additive manufacturing and tested in a controlled wind tunnel at 3.0 m/s and 2.25 m/s. Start-up time, azimuthal robustness, tip-speed-ratio evolution, and static start-up torque (interpreted through its corresponding torque coefficient) were measured and compared against a baseline NACA0018 profile. The biomimetic configuration consistently produced higher start-up torque and shorter acceleration times, achieving self-starting in 66.7% of the evaluated azimuthal positions at 2.25 m/s, compared to 22.2% for the baseline profile. Within the investigated operating range, this configuration emerged as the most robust passive strategy. The agreement between CFD predictions and experimental measurements supports the use of first-cycle maximum torque as a representative indicator of self-starting performance. These findings highlight the comparative value of first-cycle maximum torque as a practical metric for passive self-starting design assessment in low-TSR Darrieus turbines. These findings provide direct experimental evidence to guide the rational design of Darrieus turbines intended for marginal wind conditions. Full article

The transition to sustainable energy systems requires the development of efficient hydrokinetic technologies to increase the reliability and competitiveness of renewable energy generation. Vertical-axis H-Darrieus turbines can improve their performance through impeller channels or external flow guidance devices that modify the local mass flow distribution around the rotor. This work introduces a systematic geometric optimization framework that quantitatively evaluates the combined effect of key channel design parameters on turbine performance by employing response surface methodology (RSM) to quantify the influence of two geometric parameters of an impeller channel—specifically, the deflection angle ($\beta$) and the channel length (H)—on the turbine power coefficient ($C_p$). This approach allows for the identification of nonlinear interactions between geometric variables, which have not been explicitly addressed in previous research on impeller channels in H-Darrieus turbines. An experimental design with thirteen treatments was implemented, and numerical simulations were performed using Computational Fluid Dynamics (CFD) in ANSYS FLUENT^®. Statistical analysis of the RSM model showed that both $\beta$ and H have significant effects ($p<0.05$) on turbine performance. The model predicted an optimal configuration with $\beta$ equal to 100° and H equal to 0.2 m, corresponding to the maximum Cp achieved. These findings confirm the potential of impulse channels to improve the aerodynamic efficiency of H-Darrieus turbines and establish a quantitative basis for design optimization in hydrokinetic applications. Full article

Vertical-axis wind turbines (VAWTs) have received increasing research interest due to their structurally simple design and superior adaptability to gusty, multidirectional, and highly turbulent wind conditions. However, their relatively low efficiency of wind utilization remains a significant limitation, necessitating extensive research into design optimization and performance enhancement strategies. As we show, efficiency can be achieved by arranging the blades not evenly around the circumference, as in a traditional VAWT, but in groups called “blocks”, which extracts more energy from the air flow using aerodynamic and thermodynamic phenomena. The experimental results of a 20 kW VAWT in an independent certified laboratory strengthen the theoretical study and prove that the efficiency of the proposed system is 1.7 times higher than that of known VAWTs, as well as horizontal-axis wind turbines (HAWTs). Full article

Vertical axis wind turbines (VAWTs) have significant potential for renewable energy generation, yet their operational efficiency is often limited by reduced aerodynamic performance and difficulties during start-up. This study investigates the effect of passive flow control and material selection on the performance of H-Darrieus VAWT blades, with the aim of identifying design solutions that enhance start-up dynamics and overall efficiency. Two-dimensional numerical simulations were conducted using the Dynamic Mesh method with six degrees of freedom (6DOF) in ANSYS 19.2 Fluent, enabling a time-resolved assessment of rotor behavior under constant wind velocities. Two blade configurations were analyzed: a baseline NACA0012 geometry and a modified profile with inclined cavities on the extrados. In addition, the influence of blade material was examined by comparing 3D-printed resin blades with lighter 3D-printed polycarbonate blades. The results demonstrate that cavity-modified blades provide superior performance compared to the baseline, showing faster acceleration, higher tip speed ratios, and improved power coefficients, particularly at higher wind velocities. Furthermore, polycarbonate blades achieved more efficient energy conversion than resin blades, highlighting the importance of material properties in turbine optimization. These findings confirm that combining passive flow control strategies with advanced lightweight materials can significantly improve the aerodynamic and dynamic performance of VAWTs, offering valuable insights for future experimental validation and prototype development. Full article

Improvements in the aerodynamic performance of the H-Darrieus turbine are crucial to address future energy requirements. This work aims to optimize the behavior of two adjacent turbines through the addition of a dual H-Darrieus rotor. The first rotor is composed of three NACA 0021 blades, while the second comprises a single Eppler 420 blade. This study focuses on 2D CFD simulation based on the solution of the unsteady Reynolds-averaged Navier–Stokes (URANS) equations, using the sliding mesh method and $k-\omega$ SST turbulence model. The simulation results indicate a 17% improvement in the efficiency of the two turbines integrating dual rotors, compared to the two isolated turbines, for $\alpha$ = 0°. Moreover, the power coefficient ${ (C}_P)$ reaches maximum values of 0.49, 0.42, and 0.40 for angles of attack of 30°, 25°, and 20°, respectively, at TSR = 2.51. Conversely, the selection of an optimal angle of attack allows the efficiency of the two H-Darrieus turbines to be increased. It is also shown by the results that the effect of stagnation is reduced and lift is maximized when the optimum distance between two adjacent turbines is chosen. Moreover, the overall aerodynamic performance of the system is enhanced by the potential of a dual-rotor configuration, and the wake between the two turbines is disrupted, which can result in a decrease in energy production within wind farms. Full article

This study presents a general 3 × 5 × 5 factorial experimental design to maximize the Power Coefficient (Cp) of an H-Darrieus hydrokinetic turbine equipped with external accessories. Five accessory configurations (standard, cycloidal, flat plate, curve, and blocking plate), three solidity levels, and five Tip-Speed Ratio (TSR) levels were evaluated as main factors under the hypothesis that these factors significantly influence Cp. The data analyzed were obtained from numerical simulations, and their processing was conducted using Analysis of Variance (ANOVA), linear regression models, and response surfaces in the software programs Minitab 21 and RStudio V4.4.2. ANOVA makes it possible to determine the statistical significance of the effect of each factor and their interactions on the obtained Cp, identifying the accessories, TSR, and solidity that have the greatest impact on turbine performance. The results indicate that the optimal configuration to maximize Cp includes the flat-plate accessory, a solidity of 1.0, and a TSR of 3.2. From the linear regression models, mathematical relationships describing the system’s behavior were established, while the response surface analysis identified optimal operating conditions. These findings provide an effective tool for optimizing H-Darrieus turbine designs, highlighting the positive impact of accessories on performance improvement. Full article

The self-starting capability of straight-bladed H-type Darrieus Vertical Axis Wind Turbines (VAWTs) remains a major constraint for deployment, particularly in urban, low speed, and turbulent environments. We conducted a systematic review of technological strategies to improve self-starting, grouped into five categories: (1) aerodynamic airfoil design, (2) rotor configuration, (3) passive flow control, (4) active flow control, and (5) incident flow augmentation. Searches in Scopus and IEEE Xplore (last search 20 August 2025) covered the period from 2019 to 2026 and included peer-reviewed journal articles in English reporting experimental or numerical interventions on H-type Darrieus VAWTs with at least one start-up metric. From 1212 records, 53 studies met the eligibility after title/abstract screening and full-text assessment. Data were synthesized qualitatively using a comparative thematic approach, highlighting design parameters, operating conditions, and performance metrics (torque and power coefficients) during start-up. Quantitatively, studies reported typical start-up torque gains of 20–30% for airfoil optimization and passive devices, about 25% for incident-flow augmentation, and larger but less certain improvements (around 30%) for active control. Among the strategies, airfoil optimization and passive devices consistently improved start-up torque at low TSR with minimal added systems; rotor-configuration tuning and incident-flow devices further reduced start-up time where structural or siting constraints allowed; and active control showed the largest laboratory gains but with uncertain regarding energy and durability. However, limitations included heterogeneity in designs and metrics, predominance of 2D-Computational Fluid Dynamics (CFDs), and limited 3D/field validation restricted quantitative pooling. Risk of bias was assessed using an ad hoc matrix; overall certainty was rated as low to moderate due to limited validation and inconsistent uncertainty reporting. In conclusions, no single solution is universally optimal; hybrid strategies, combining optimized airfoils with targeted passive or active control, appear most promising. Future work should standardize start-up metrics, adopt validated 3D Fluid–Structure Interaction (FSI) models, and expand wind-tunnel/field trials. Full article

H-Darrieus vertical-axis wind turbines (VAWTs) capture wind regardless of its direction and operate effectively even in challenging and turbulent wind conditions. As a result, the blades operate under erratic and intricate aerodynamic loads, which cause them to bend. The performance of the H-Darrieus rotor will therefore be impacted by the blade’s deflection. This study aims at investigating the dynamic aerostructure influence on a novel convex-bladed H-Darrieus geometry. The results are compared to a straight-bladed baseline rotor. To do so, a two-way fluid–structure interaction (FSI)-coupled approach is performed to accurately address this issue. This approach allows for the simultaneous resolution of the fluid flow around the rotor and the mechanical structure responses inside the blades. The turbulent flows are resolved using the k-ω-SST model together with the URANS equations through computational fluid dynamics (CFD), while the structural deflections of the blades are assessed using finite element analysis (FEA). The results show that the performance of both H-Darrieus turbines decreases with increasing deformation. In addition, the study found that the carbon fiber composite (M1) material has the least deformation in the convex and straight blades, with values of 9.1 mm and 20.331 mm, respectively. The glass-fiber-reinforced epoxy composite (M3) material shows the most significant deflection across both types, with displacements of 32.50 mm and 73.78 mm for the straight blade and 19.02 mm and 43.03 mm for the convex blade. This study also reveals that the straight blade has a peak displacement of 73.785 mm when using the M3 material at TSR = 3, while the convex blade has a minimum displacement of 20.331 mm when using the M1 material, highlighting the varying performance characteristics of the materials. The maximum stress observed occurs in the straight blade, registering at 324.1 MPa with TSR = 3, which aligns closely with the peak displacement values, particularly for the aluminum alloy material (M2). In contrast, the convex blade made from the first material (M1) exhibits the lowest stress levels among the tested configurations. Full article

This paper presents the results of experimental, analytical, and numerical studies on determining the driving torque and power of a vertical-axis wind turbine (VAWT) with planetary blade motion forced by a carousel rotor. First, experimental studies in the wind tunnel laboratory were conducted to determine the tip speed ratio λ for the real-scale wind turbine model under self-starting conditions. Then, an analytical kinematic model of the turbine was developed. Finally, computational fluid dynamics (CFD) analysis was conducted to verify the analytical approach and examine aerodynamic interferences between particular turbine blades. The main objective of the study was to verify the accuracy of the simplified analytical approach to calculating the driving torque and turbine power compared to the numerical results based on 2D analysis using computational fluid dynamics. The obtained results showed good agreement considering the modeling of the motion of the three dual-coherent blades of the wind turbine. Comparing the analytical and CFD approaches, the error in determining the average driving torque and the average turbine power was about 1%. An additional objective of the study was to use the developed analytical method to calculate the starting torque and demonstrate the main advantage of the carousel wind rotor, which is its higher starting torque compared to the H-type Darrieus rotor. Full article

This study investigates the aerodynamic performance and flow dynamics of an H-type Darrieus vertical axis wind turbine (VAWT) using combined numerical and experimental methods. The analysis examines the effects of operational parameters, such as rotor solidity and pitch angle, on aerodynamic loads and flow characteristics, using a 2-D URANS simulation with the Transition SST model to capture transient effects. Validation was conducted in a low-turbulence wind tunnel to observe the impact of variable flow conditions. The LineAverage method for determining the angle of attack demonstrated strong correlations between rotor configuration and load variations, particularly highlighting the influence of blade number and pitch angle on aerodynamic efficiency. This research supports optimization strategies for Darrieus VAWTs in urban environments, where turbulent, low-speed conditions challenge conventional wind turbine designs. Full article

Blade pitch angle regulation is an effective approach to enhance the performance of H-type Darrieus Vertical Axis Wind Turbines (VAWTs). Improving the blade interaction with the wind for this type of rotor is a challenging task, especially in unsteady wind conditions. This paper presents a novel hybrid approach that integrates fixed and variable blade pitch angle regulation techniques, aiming to enhance the wind turbine efficiency across various operational stages and wind speeds. The proposed blade pitch angle regulation method targets a less complicated, mechanically feasible, and cost-effective pitching technique. This study uses the Double Multiple Streamtube (DMST) model to analyze the aerodynamic performance and calculate the power output generated at different pitch angles. MATLAB Simulink was utilized to implement the DMST model, and experimental validation was conducted to confirm the results. The findings indicate that the blade pitch angle regulation has significantly enhanced the self-starting ability of H-type Darrieus VAWT by 80%. Additionally, the maximum rotational speed and power coefficient are achieved at a zero pitch angle. Furthermore, regulating the blade pitch angle allows for the effective control of excessive rotational speeds during high wind conditions. Full article