Search Results (74)

In this paper, a joint Matching Field Processing (MFP) Algorithm based on horizontal uniform circular array (UCA) is proposed for three-dimensional position of underwater wrecked targets. Firstly, a Marine search and rescue position model based on Minimum Variance Distortionless Response (MVDR) and matching field quadratic joint Algorithm was proposed. Secondly, an MVDR beamforming method based on pre-Kalman filtering is designed to refine the real-time DOA estimation of the desired signal and the interference source, and the sound source azimuth is determined for prepositioning. The antenna array weights are dynamically adjusted according to the filtered DOA information. Finally, the Adaptive Matching Field Algorithm (AMFP) used the DOA information to calculate the range and depth of the lost target, and obtained the range and depth estimates. Thus, the 3D position of the lost underwater target is jointly estimated. This method alleviates the angle ambiguity problem and does not require a computationally intensive 2D spectral search. The simulation results show that the proposed method can better realise underwater three-dimensional positioning under certain signal-to-noise ratio conditions. When there is no error in the sensor coordinates, the positioning error is smaller than that of the baseline method as the SNR increases. When the SNR is 0 dB, with the increase in the sensor coordinate error, the target location error increases but is smaller than the error amplitude of the benchmark Algorithm. The experimental results verify the robustness of the proposed framework in the hierarchical ocean environment, which provides a practical basis for the deployment of rapid response underwater positioning systems in maritime search and rescue scenarios. Full article

We propose a hybrid Convolutional Graph Neural Network (C-GNN) for direction-of-arrival (DOA) estimation in sparse sensor arrays under low-snapshot conditions. The C-GNN architecture combines 1D convolutional layers for local spatial feature extraction with graph convolutional layers for global structural learning, effectively capturing both fine-grained and long-range array dependencies. Leveraging the difference coarray technique, the sparse array is transformed into a virtual uniform linear array (VULA) to enrich the spatial sampling; real-valued covariance matrices derived from the array measurements are used as the network’s input features. A final multi-layer perceptron (MLP) regression module then maps the learned representations to continuous DOA angle estimates. This approach capitalizes on the increased degrees of freedom offered by the virtual array while inherently incorporating the array’s geometric relationships via graph-based learning. The proposed C-GNN demonstrates robust performance in noisy, low-data scenarios, reliably estimating source angles even with very limited snapshots. By focusing on methodological innovation rather than bespoke architectural tuning, the framework shows promise for data-efficient DOA estimation in challenging practical conditions. Full article

We propose an efficient Nyström-based unitary subspace method for low-complexity two-dimensional (2D) direction-of-arrival (DOA) estimation in uniform rectangular array (URA) signal processing systems. The conventional high-resolution DOA estimation methods often suffer from excessive computational complexity, particularly when dealing with large-scale antenna arrays. The proposed method addresses this challenge by combining the Nyström approximation with a unitary transformation to reduce the computational burden while maintaining estimation accuracy. The signal subspace is approximated using a partitioned covariance matrix, and a real-valued transformation is applied to further simplify the eigenvalue decomposition (EVD) process. Furthermore, the linear prediction coefficients are estimated via a weighted least squares (WLS) approach, enabling robust extraction of the angular parameters. The 2D DOA estimates are then derived from these coefficients through a closed-form solution, eliminating the need for exhaustive spectral searches. Numerical simulations demonstrate that the proposed method achieves comparable estimation performance to state-of-the-art techniques while significantly reducing computational complexity. For a fixed array size of $M=N=20$, the proposed method demonstrates significant computational efficiency, requiring less than $50\%$ of the running time compared to conventional ESPRIT, and only $6\%$ of the time required by ML methods, while maintaining similar performance. This makes it particularly suitable for real-time applications where computational efficiency is critical. The novelty lies in the integration of Nyström approximation and unitary subspace techniques, which jointly enable efficient and accurate 2D DOA estimation without sacrificing robustness against noise. The method is applicable to a wide range of array processing scenarios, including radar, sonar, and wireless communications. Full article

The acoustically actuated antenna technology enables a significant reduction in antenna dimension, facilitating miniaturization of ground-penetrating radar systems in the very high-frequency (VHF) band. However, the current acoustically actuated antennas suffer from narrow bandwidth and low range resolution. To address this issue, this paper proposed a three-dimensional (3D) localization method for underground targets, which combined two-dimensional (2D) array direction-of-arrival (DOA) estimation with continuous spatial sampling without relying on range resolution. By leveraging the small dimension of acoustically actuated antennas, a 2D uniform linear array was formed to obtain the target’s angle using DOA estimation. Based on the variation pattern of 2D angles in continuous spatial sampling, the genetic algorithm was employed to estimate the 3D coordinates of underground targets. The numerical simulation results indicated that the root mean square error (RMSE) of the proposed 3D localization method is 1.68 cm, which outperforms conventional methods that utilize wideband frequency-modulated pulse signals with hyperbolic vertex detection in theoretical localization accuracy, while also demonstrating good robustness. The gprMax electromagnetic simulation results further confirmed that this method can effectively localize multiple targets in ideal homogeneous underground media. Full article

The Direction-of-Arrival (DOA) estimation method using traditional array antennas cannot dynamically adjust the observation angle range based on the Region of Interest (ROI), which leads to limited estimation accuracy and high computational complexity. To address the above issue, this paper proposes a Beamspace Spatial Smoothing MUltiple SIgnal Classification (BSS-MUSIC) DOA estimation method using a Dynamic Metasurface Antenna (DMA). Specifically, we propose a new DMA model with a single RF chain and exploit its flexibility to design a time-division data reception scheme. Based on this scheme, we dynamically select the ROI and increase the beam density in the ROI with an appropriate number of beam patterns. Next, a BSS algorithm is proposed to decohere the multipath signals in beamspace without reverting to the element space. Subsequently, we convert the 2D DOA estimation into two 1D beamspace MUSIC DOA estimations. After pairing the elevation and azimuth angles, the complex gains of each path are derived. Simulation results show that the proposed method can achieve higher estimation accuracy with lower computational complexity. Full article

Conventional acoustic velocity-independent direction of arrival (DOA) estimation models have limited measurement ranges and low degrees of freedom. This paper proposes an omnidirectional DOA estimation model based on improved Toeplitz matrix reconstruction to address these issues. The proposed method focuses on the Toeplitz matrix reconstruction method for sparse arrays to enhance the degree of freedom of the arrays. The method employs an expanding coprime array with a larger aperture, eliminating the acoustic velocity factor through geometric relationships and constructing a larger-size Toeplitz matrix. In addition, the concept of “low-rank matrix reconstruction” is introduced to fill the vacant terms in the Toeplitz matrix. Finally, the simulation experiments demonstrate the effectiveness of the proposed algorithm in improving the estimation accuracy. Full article

Frequency diversity array–multiple-input multiple-output (FDA-MIMO) radar realizes an angle- and range-dependent system model by adopting a slight frequency offset between adjacent transmitter sensors, thereby enabling potential target localization. This paper presents FDA-MIMO radar-based rapid target localization via the reduction dimension root reconstructed multiple signal classification (RDRR-MUSIC) algorithm. Firstly, we reconstruct the two-dimensional (2D)-MUSIC spatial spectrum function using the reconstructed steering vector, which involves no coupling of direction of arrival (DOA) and range. Subsequently, the 2D spectrum peaks search (SPS) is converted into one-dimensional (1D) SPS to reduce the computational complexity using a reduction dimension transformation. Finally, we conduct polynomial root finding to further eliminate computational costs, in which DOA and range can be rapidly estimated without performance degradation. The simulation results validate the effectiveness and superiority of the proposed RDRR-MUSIC algorithm over the conventional 2D-MUSIC algorithm and reduced-dimension (RD)-MUSIC algorithm. Full article

Phase noise is a consequence of the instability inherent in the operation of oscillators, making it impossible to entirely eliminate. For low-cost internet of things (IoT) devices, this type of noise can be particularly pronounced, posing a challenge in providing high-quality localization services. To tackle this issue, this paper introduces an improved localization algorithm that includes phase noise compensation. The proposed algorithm enhances the direction of arrival (DoA) estimation for each base station by employing the EM–MUSIC method, subsequently forming a non-convex optimization problem based on the mean square error (MSE) of the estimated DoA results. Finally, a closed-form solution is derived through rational assumptions and approximations. Results show that this algorithm effectively minimizes localization errors and achieves accuracy levels within the sub-meter range. Full article

This study applied modified linear regression in machine learning (ML) to predict the direction of arrival (DoA) in cellular networks using field measurements and radiofrequency parameters. Models were developed from base station data, with preprocessing for pattern identification and formula adjustments to improve the accuracy across angle ranges. Machine learning, tested here as an additional method to traditional techniques, achieved a root mean square error (RMSE) of 3.63 to 17.93, demonstrating enhanced adaptability. While requiring substantial data and computational resources, this approach highlights machine learning’s potential as a valuable tool for DoA estimation in cellular networks. Full article

High-frequency surface wave radar (HFSWR) is widely used for detecting sea surface or low-altitude targets due to its all-weather operation and over-the-horizon detection capability. To further enhance the maneuverability and detection range of HFSWR, shipborne HFSWR has been developed. However, compared to shore-based platforms, shipborne platforms face challenges such as a small array aperture and reduced Direction of Arrival (DOA) estimation performance due to their limited size. The traditional time–domain virtual aperture extension method, based on the principle of space-time equivalence, aims to improve the array aperture but has limitations when used for HFSWR background or multiple targets with different speeds. To address these issues, this paper proposes a range-Doppler domain (RD-domain) virtual aperture extension method for the uniform linear array, based on the uniform motion model. The contributions of this work include (1) a continuous motion model for shipborne HFSWR, (2) a virtual aperture processing flowchart for shipborne HFSWR, and (3) an RD-domain aperture extension method suitable for HFSWR background or multiple targets with varying speeds. Through simulation and experimental data, we validate the proposed method and analyze its performance. Full article

Utilizing hydrophone arrays for detecting underwater acoustic communication (UWAC) signals leverages spatial information to enhance detection efficiency and expand the perceptual range. This study redefines the task of UWAC signal detection as an object detection problem within the frequency–azimuth (FRAZ) spectrum. Employing Faster R-CNN as a signal detector, the proposed method facilitates the joint prediction of UWAC signals, including estimates of the number of sources, modulation type, frequency band, and direction of arrival (DOA). The proposed method extracts precise frequency and DOA features of the signals without requiring prior knowledge of the number of signals or frequency bands. Instead, it extracts these features jointly during training and applies them to perform joint predictions during testing. Numerical studies demonstrate that the proposed method consistently outperforms existing techniques across all signal-to-noise ratios (SNRs), particularly excelling in low SNRs. It achieves a detection F1 score of 0.96 at an SNR of −15 dB. We further verified its performance under varying modulation types, numbers of sources, grating lobe interference, strong signal interference, and array structure parameters. Furthermore, the practicality and robustness of our approach were evaluated in lake-based UWAC experiments, and the model trained solely on simulated signals performed competitively in the trials. Full article

As one of the most widely used spread spectrum techniques, the frequency-hopping spread spectrum (FHSS) has been widely adopted in both civilian and military secure communications. In this technique, the carrier frequency of the signal hops pseudo-randomly over a large range, compared to the baseband. To capture an FHSS signal, conventional non-cooperative receivers without knowledge of the carrier have to operate at a high sampling rate covering the entire FHSS hopping range, according to the Nyquist sampling theorem. In this paper, we propose an adaptive compressed method for joint carrier and direction of arrival (DOA) estimations of FHSS signals, enabling subsequent non-cooperative processing. The compressed measurement kernels (i.e., non-zero entries in the sensing matrix) have been adaptively designed based on the posterior knowledge of the signal and task-specific information optimization. Moreover, a deep neural network has been designed to ensure the efficiency of the measurement kernel design process. Finally, the signal carrier and DOA are estimated based on the measurement data. Through simulations, the performance of the adaptively designed measurement kernels is proved to be improved over the random measurement kernels. In addition, the proposed method is shown to outperform the compressed methods in the literature. Full article

Accurate localization of devices within Internet of Things (IoT) networks is driven by the emergence of novel applications that require context awareness to improve operational efficiency, resource management, automation, and safety in industry and smart cities. With the Integrated Localization and Communication (ILAC) functionality, IoT devices can simultaneously exchange data and determine their position in space, resulting in maximized resource utilization with reduced deployment and operational costs. Localization capability in challenging scenarios, including harsh environments with complex geometry and obstacles, can be provided with robust, reliable, and energy-efficient communication protocols able to combat impairments caused by interference and multipath, such as the IEEE 802.15.4 Time-Slotted Channel Hopping (TSCH) protocol. This paper presents an enhancement of the TSCH protocol that integrates localization functionality along with communication, improving the protocol’s operational capabilities and setting a baseline for monitoring, automation, and interaction within IoT setups in physical environments. A novel approach is proposed to incorporate a hybrid localization by integrating Direction of Arrival (DoA) estimation and Multi-Carrier Phase Difference (MCPD) ranging methods for providing DoA and distance estimates with each transmitted packet. With the proposed enhancement, a single node can determine the location of its neighboring nodes without significantly affecting the reliability of communication and the efficiency of the network. The feasibility and effectiveness of the proposed approach are validated in a real scenario in an office building using low-cost proprietary devices, and the software incorporating the solution is provided. The experimental evaluation results show that a node positioned in the center of the room successfully estimates both the DoA and the distance to each neighboring node. The proposed hybrid localization algorithm demonstrates an accuracy of a few tens of centimeters in a two-dimensional space. Full article

How to enhance the desired signal with low signal-to-noise ratio (SNR) is a difficult problem in the estimation process of the direction-of-arrival (DOA) of the target scattering wave signal. In this paper, the feasibility of spatial spectrum estimation in the Range-Doppler (RD) domain is analyzed in principle, and the SNR gain expression of weak scattering wave signal is derived when constructing multi-snapshots virtual array data. On this basis, the mutual eigenvector singular value decomposition (MESVD) method based on RD domain mode excitation is proposed, which can robustly and effectively estimate the direction of the coherent weak signals. Simulation experiments verify that the RD domain spectral estimation method has the ability to simultaneously obtain the direction of multiple weak target scattering waves, and the direction-finding accuracy can reach the Cramer–Rao bound (CRB) of conventional spectral estimation method. The results of Monte Carlo experiments show that the root-mean-square-error (RMSE) of azimuth estimation of RD domain spatial spectrum estimation method is 5.76° lower than that of a conventional multiple signal classification (MUSIC) method. In addition, the practicability of the proposed method is demonstrated by comparing the DOA estimation results of a set of real data with Automatic Dependent Surveillance-Broadcast (ADS-B) data. Full article

Increasing airspace safety is an important challenge, both for unmanned aerial vehicles (UAVs) as well as manned aircraft. Future developments of collision avoidance systems are supposed to utilize information from multiple sensing systems. A compact sensing system could employ a multi-mode multi-port antenna (M${ }^3$PA). Their ability to radiate multiple orthogonal patterns simultaneously makes them suitable for communication applications as well as bearing and ranging applications. Furthermore, they can be designed to flexibly originate near-omnidirectional and/or directional radiation patterns. This option of flexibility with respect to the radiation characteristic is desired for antennas integrated in collision avoidance systems. Based on the aforementioned properties, M${ }^3$PAs represent a compelling option for aircraft transponders. In this paper, direction-of-arrival (DoA) estimation using an M${ }^3$PA designed for aerial applications is put to the test. First, a DoA estimation scheme suitable to be employed with M${ }^3$PAs is introduced. Next, the validity of the proposed method is confirmed through numerical simulations. Lastly, practical experiments are conducted in an antenna measurement chamber to verify the numerical results. Full article