Search Results (613)

The microstructure, phase composition, and high-temperature oxidation resistance of Fe-free AlCoCrNiNb_0.2 and AlCoCr_0.5NiNb_0.2 high-entropy alloys (HEAs) were investigated. In the as-cast HEAs, niobium was found to mainly release as a Laves phase in the interdendritic region, and its solubility in the dendrites of the BCC solid solution was about 2 at.%. Both samples exhibited parabolic behavior during 100 h oxidation at 1000 °C and 1100 °C. The AlCoCrNiNb_0.2 alloy demonstrated higher resistance to high-temperature oxidation compared to AlCoCr_0.5NiNb_0.2. The specific weight changes after 100 h of isothermal holding at 1000 °C and 1100 °C were 0.65 mg/cm² and 1.31 mg/cm², respectively, which are superior compared to the Fe-containing HEAs. Cr was revealed to play an important role in the oxidation behavior of the HEAs, decreasing the parabolic oxidation rate constant and increasing the activation energy of the oxidation process in the alloys. Full article

The interface between high-performance thermoelectric materials and electrodes critically governs the conversion efficiency and long-term reliability of thermoelectric generators under high-temperature operation. Here, we propose Al_xCoCrFeNi high-entropy alloys (HEA) as barrier layers to bond Cu-W electrodes with p-type skutterudite (p-SKD) thermoelectric materials. The HEA/p-SKD interface exhibited excellent chemical bonding with a stable and controllable reaction layer, forming a dense, defect-free (Fe,Ni,Co,Cr)Sb phase (thickness of ~2.5 μm) at the skutterudites side. The interfacial resistivity achieved a low value of 0.26 μΩ·cm² and remained at 7.15 μΩ·cm² after aging at 773 K for 16 days. Moreover, the interface demonstrated remarkable mechanical stability, with an initial shear strength of 88 MPa. After long-term aging for 16 days at 773 K, the shear strength retained 74 MPa (only 16% degradation), ranking among the highest reported for thermoelectric materials/metal joints. Remarkably, the joint maintained a shear strength of 29 MPa even after 100 continuous thermal cycles (623–773 K), highlighting its outstanding thermo-mechanical stability. These results validate the Al_xCoCrFeNi high-entropy alloys as an ideal interfacial material for thermoelectric generators, enabling simultaneous optimization of electrical and mechanical performance in harsh environments. Full article

This study synthesized FeNiCuAlX high-entropy alloys (HEAs) (where X = Cr, Co, Mn) using arc melting and investigated their high-temperature oxidation behavior in air at 900 °C. The oxidation kinetics of all alloys followed a parabolic rate, with the oxidation rate constants (kp) of FeNiCuAlCr, FeNiCuAlCo, and FeNiCuAlMn being approximately two to three orders of magnitude lower than that of the FeNiCu alloy. Specifically, FeNiCuAlCr exhibited the lowest kp value of 1.72 × 10⁻⁶ mg²·cm⁴/s, which is significantly lower than those of FeNiCuAlCo (3.29 × 10⁻⁶ mg²·cm⁴/s) and FeNiCuAlMn (1.71 × 10⁻⁵ mg²·cm⁴/s). This suggests that the addition of chromium promotes the formation of a dense Al₂O₃/Cr₂O₃ oxide layer, significantly enhancing the oxidation resistance. Furthermore, corrosion resistance was assessed through potentiodynamic polarization and electrochemical impedance spectroscopy in a 3.5% NaCl solution. FeNiCuAlCr demonstrated exceptional resistance to localized corrosion, as indicated by its low corrosion current density (45.7 μA/cm²) and high pitting potential (−0.21 V), highlighting its superior corrosion performance. Full article

Graphene, a remarkable two-dimensional material, enhances the mechanical properties of high-entropy alloys as a reinforcing phase. This study investigated the influence of vacancy defects in graphene on the strengthening effect of FeNiCrCoCu high-entropy alloy through molecular dynamics simulations. The findings reveal that vacancy defects diminish graphene’s strength, resulting in its premature failure. In tensile tests, graphene with defects lowers the yield stress of the composite, yet it retains the ability to impede dislocations. Conversely, graphene exhibits a more pronounced strengthening effect during compression. Specifically, when the deletion of C atoms is less than 1%, the impact is negligible; between 1% and 6%, the strengthening effect diminishes; and when it surpasses 6%, the strengthening effect virtually ceases to exist. This research offers a theoretical foundation for optimizing graphene-reinforced composites. Full article

In recent years, interest in HEAs has increased exponentially due to their extraordinary properties, especially for wear- and corrosion-resistant applications. However, the main problem involves correctly selecting the HEA composition required for a specific application, as most of the data are scattered throughout the literature, and only a limited number of models accurately predict the properties. Therefore, a database of 415 HEA alloys (bulk) and coatings obtained using thermal spray (TS) techniques has been created, compiled from scientific studies over the past 20 years. This tool collects information on physical, mechanical, and chemical properties, with a particular emphasis on corrosion and wear resistance. This facilitates material comparison and selection according to the needs of a specific application. In particular, the database highlights how composition and deposition technique also affect performance, identifying CoCrFeNi (CGS and in bulk) as a promising candidate for simultaneous wear and corrosion resistance. Full article

This study investigates the microstructural evolution, mechanical behavior, and electrochemical performance of CoCrFeNiNb and CoCrFeNiV HEAs fabricated via mechanical alloying and spark plasma sintering. Microstructural analyses reveal that the alloys have a face-centered cubic (FCC) matrix with Nb-enriched Laves and V-enriched σ phases. The CoCrFeNiNb HEA exhibits superior compressive strength and hardness than CoCrFeNiV due to uniform Laves phases distribution. Fracture surface analysis reveals that at lower sintering temperatures, the fracture is primarily caused by incomplete particle bonding, whereas at higher temperatures, brittle fracture modes dominated via transgranular cracking become predominant. The research results of potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) show that both alloys exhibited superior electrochemical stability in a 3.5 wt.% NaCl solution compared to the CoCrFeNi base alloy. X-ray photoelectron spectroscopy (XPS) analysis confirms the formation of stable oxide layers (Nb₂O₅ and V₂O₃) on the precipitated phases, acting as protective barriers against chloride ion penetration. The selective oxidation of Nb and V improves the integrity of the passive film, reducing the corrosion rates and enhancing the long-term durability. These findings highlight the critical role of precipitated phases in enhancing the corrosion resistance of HEAs, and emphasize their potential for use in extreme environments. Full article

The erosion resistance of materials against solid particles is a very important property, especially in the transportation of powders or in aeronautics (dust inside jet engines). There is a strong need to introduce new materials that have higher solid particle erosion resistance than state-of-the-art materials. Thus, in the present work, the solid erosion particles of high entropy alloys (HEAs) based on the Al0.7CoCrFeNi matrix were studied compared to the state-of-the-art stainless steel AISI 304. Furthermore, the effect of the addition of Ti to HEAs on hardness and erosion resistance was investigated. Current research included the development of the chemical composition of a new kind of HEA designed on the basis of thermodynamical calculations performed in CALPHAD, its manufacturing, full characterization involving microstructural and phase analyses, hardness measurements, solid particle erosion tests, and finally, the elucidation of erosion mechanisms. It was found that HEAs showed higher hardness as well as erosion resistance than AISI 304. Moreover, it was found that the increase in Ti content in an HEA resulted in an increase in the hardness and resistance to the erosion of the studied HEA. As the main reason for this phenomenon, the stabilization of the β-BCC phase, suppression of the α-FCC phase, and the appearance of the Ni₃Ti phase in the studied HEA were claimed. Full article

In this paper, the impact of mechanical alloying (MA) and spark plasma sintering (SPS) on the phase evolution and mechanical properties development of CoCrFeNiTi high–entropy alloys (HEAs) was investigated. The microstructure and properties of the material were examined, using X-ray diffraction (XRD) for phase identification, scanning electron microscopy (SEM) for surface morphology observation, transmission electron microscopy (TEM) for microstructural analysis, and hardness testing to evaluate mechanical performance. The milled powder exhibited nanocrystalline solid solution microstructure with grain sizes below 48 nm, composed of 83% face–centered cubic (FCC) and 17% body–centered cubic (BCC) phases. Mechanically, the bulk CoCrFeNiTi alloy exhibited exceptional strength attributes, as evidenced by a Vickers hardness value reaching 675 Hv, along with a compressive strength of 1894 MPa and a yield stress of 1238 MPa. These findings suggested that the synergistic effects of mechanical alloying and SPS processing can precisely control the phase stability, microstructure refinement, and property optimization in CoCrFeNiTi HEA, with particular promise for advanced structural applications. Full article

This study systematically investigates the effects of heat treatment at 800–1000 °C on the microstructure and mechanical properties of 10 wt.% TiB₂@Ti/AlCoCrFeNi_2.1 eutectic high-entropy alloy matrix composites (EHEAMCs) prepared by vacuum hot-pressing sintering. The results show that the materials consist of FCC, BCC, TiB₂, and Ti phases, with a preferred orientation of the (111) crystal plane of the FCC phase. As the temperature increases, the diffraction peak of the BCC phase separates from the main FCC peak and its intensity increases, while the diffraction peak positions of the FCC and BCC phases shift at small angles. This is attributed to the diffusion of TiB₂@Ti from the grain boundaries into the matrix, where the Ti solid solution increases the lattice constant of the FCC phase. Microstructural observations reveal that the eutectic region transforms from lamellar to island-like structures, and the solid solution zone narrows. With increasing temperature, the Ti concentration in the solid solution zone increases, while the contents of elements such as Ni decrease. Element diffusion is influenced by binary mixing enthalpy, with Ti and B tending to solidify in the FCC and BCC phase regions, respectively. The mechanical properties improve with increasing temperature. At 1000 °C, the average hardness is 579.2 HV, the yield strength is 1294 MPa, the fracture strength is 2385 MPa, and the fracture strain is 19.4%, representing improvements of 35.5% and 24.9% compared to the as-sintered state, respectively, without loss of plasticity. The strengthening mechanisms include enhanced solid solution strengthening due to the diffusion of Ti and TiB₂, improved grain boundary strength due to the diffusion of alloy elements to the grain boundaries, and synergistic optimization of strength and plasticity. Full article

High-entropy alloy (HEA) particle-reinforced metal matrix composites (MMCs) are a new generation of MMCs with potential applications as orthopedic material in automotive, aerospace, and biomedical fields. In this study, AlCoCrFeNi HEA-reinforced Ti-6Al-4V metal matrix composites (MMCs) were prepared by microwave sintering. The microstructural aspects of the MMC were investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM), with an emphasis on the interdiffusion (ID) layer. The mechanical properties of the composites were studied by micro-pillar compression at the micro-length scale. The results show that the ID layer exists between the HEA particles and the matrix, is equiaxed in nature, and leads towards metallurgical bonding within the composite. The strength of this ID layer (1573 MPa of yield strength and 1867 MPa of compressive strength) and its Young’s modulus (570 MPa) were about 1.5 times lower than that of the matrix. The HEA particles exhibit the highest strength (2157 MPa of yield strength and 3356 MPa of compressive strength) and Young’s modulus (643 MPa), whereas the matrix falls in between 2372 MPa of yield strength and 2661 MPa of compressive strength, and a Young’s modulus of 721 MPa. Full article

In this study, powders based on a high-entropy AlCoCrFeNi alloy obtained by mechanical alloying were successfully applied to a 316L stainless steel substrate by detonation spraying under various conditions. Their microstructural features, phase composition, hardness, and wear resistance were studied. A comparative analysis between the initial powder and the coatings was performed, including phase transformation modeling using Thermo-Calc under non-equilibrium conditions. The results showed that the phase composition of the powder and coatings includes body-centered cubic lattice (BCC), its ordered modification (B2), and face-centered cubic lattice FCC phases, which is consistent with the predictions of the Scheil solidification model, describing the process of non-equilibrium solidification, assuming no diffusion in the solid phase and complete mixing in the liquid phase. Rapid solidification and high-speed impact deformation of the powder led to significant grain refinement in the detonation spraying coating, which ultimately improved the mechanical properties at the micro level. The data obtained demonstrate the high efficiency of the AlCoCrFeNi coating applied by detonation spraying and confirm its potential for use in conditions of increased wear and mechanical stress. AlCoCrFeNi coatings may be promising for use as structural materials in the future. Full article

Based on the innovative mode driven by “data + artificial intelligence”, in this study, three methods, namely Gaussian noise (GAUSS Noise), the Generative Adversarial Network (GAN), and the optimized Generative Adversarial Network (GANPro), are adopted to expand and enhance the collected dataset of element contents and the hardness of the AlCoCrCuFeNi high-entropy alloy. Bayesian optimization with grid search is used to determine the optimal combination of hyperparameters, and two interpretability methods, SHAP and permutation importance, are employed to further explore the relationship between the element features of high-entropy alloys and hardness. The results show that the optimal data augmentation method is Gaussian noise enhancement; its accuracy reaches 97.4% under the addition of medium noise (σ = 0.003), and an optimal performance prediction model based on the existing dataset is finally constructed. Through the interpretability method, it is found that the contributions of Al and Ni are the most prominent. When the Al content exceeds 0.18 mol, it has a positive promoting effect on hardness, while Ni and Cu exhibit a critical effect of promotion–inhibition near 0.175 mol and 0.14 mol, respectively, revealing the nonlinear regulation law of element contents. This study solves the problem of revealing the mutual relationship between the element contents and hardness of high-entropy alloys in the case of a lack of alloy data and provides theoretical guidance for further improving the performance of high-entropy alloys. Full article

High-entropy alloys are known for their promising mechanical properties, wear and corrosion resistance, which are maintained across a wide range of temperatures. In this study, a CoCrFeNiCu-based high-entropy alloy, distinguished from conventional CoCrFeNi systems by the addition of Cu, which is known to enhance toughness and wear resistance, was investigated to better understand the effects of compositional modification on processability and performance. The influence of key process parameters, specifically laser power and scan speed, on the processability of CoCrFeNiCu-based high-entropy alloys produced by laser powder bed fusion additive manufacturing was investigated, with a focus of low laser power, which is critical for minimizing defects and improving the resulting microstructure and mechanical performance. The printed sample density gradually increases with higher volumetric energy density, achieving densities exceeding 99.0%. However, at higher energy densities, the samples exhibit susceptibility to hot cracking, an issue that cannot be mitigated by adjusting the process parameters. Mechanical properties under optimized parameters were further evaluated using Charpy impact and (in situ) tensile tests. These evaluations were supplemented by in situ tensile experiments conducted within a scanning electron microscope to gain insights into the behavior of defects, such as hot cracks, during tensile testing. Despite the sensitivity to hot cracking, the samples exhibited a respectable ultimate tensile strength of 662 MPa, comparable to fine-grained steels like S500MC (070XLK). These findings underscore the potential of CoCrFeNiCu-based high-entropy alloys for advanced applications. However, they also highlight the necessity for developing strategies to ensure stable and reliable processing methods that can mitigate the susceptibility to hot cracking. Full article

This paper studies how heat treatments influence the corrosion of an AlCoCrFeNi_2.1 eutectic high-entropy alloy (EHEA) in a 3.5 wt% NaCl solution, by comparing the corrosion behaviors of as-cast, 600 °C heat-treated, and 1000 °C heat-treated samples using microstructure characterization, electrochemical measurements, and surface characterization. The electrochemical results show that the pitting potential rises and the passive current density and passive film resistance are almost changeless with an increasing heat treatment temperature. The enhancement in the pitting corrosion resistance results from the increased amount of the Cr-rich FCC phase and decreased amount of the B2 phase rich in the Al element, which are induced by the heat treatment. On one hand, this microstructure evolution can make the passive film have more Cr₂O₃ and less Al₂O₃, thereby enhancing its protective properties, as confirmed by the X-ray photoelectron spectroscopy analysis. On the other hand, the decreased amount of the Al-rich B2 phase can make the pitting corrosion less prone to initiate since the B2 phase can act as the pit initiation site, which is supported by the observation of corrosion morphologies, due to its higher electrochemical activity. In a summary, the heat treatment is beneficial for improving the pitting corrosion resistance of the AlCoCrFeNi_2.1 EHEA. Full article

This study synthesized Al₂CoCrFeNi high-entropy alloy (HEA) using spark plasma sintering (SPS) followed by annealing treatment. The effects of heat treatment on the microstructure, mechanical properties, wear resistance, and thermoelectric properties were systematically investigated. The annealed alloy exhibited a microhardness increase from 538.5 HV to 550.9 HV and a significant improvement in ultimate compressive strength from 1540.74 MPa to 2563.67 MPa, attributed to grain homogenization and reduced dislocation density. Wear resistance tests revealed a decrease in wear rate from 7.15 × 10⁻⁵ mm³/(N·m) to 4.74 × 10⁻⁵ mm³/(N·m), with wear morphology analysis confirming enhanced resistance to plastic deformation. Thermoelectric characterization demonstrated that thermal diffusivity increased from 2.98 mm²/s to 3.11 mm²/s at room temperature, while the absolute Seebeck coefficient reached 8.0 μV/K at 200 °C, indicating improved electron transport efficiency due to lattice ordering. This combination of high hardness, high thermal conductivity, and excellent wear resistance presents unique application value in extreme tribological fields involving thermal management and simultaneous surface wear resistance and heat dissipation. Full article