Search Results (269)

In the present work a new regime of periodical energy exchange between pump, signal and idler waves, under the influence of the process of four-wave mixing (FWM), with additional consideration of the effects of self-phase modulation (SPM) and cross-phase modulation (XPM), is presented. In our previous papers a theoretical model which successfully describes the amplification and periodic energy exchange between the three optical waves in CW regime of laser source propagation (short-cut equations) was developed. Exact analytical solutions, describing the periodic changes in the intensities of pump, signal and idler waves, were found and expressed by the Jacobi elliptic functions. The period of the energy exchange between the waves can be presented by elliptic integral of the first kind. In the current research, the periods of energy exchange between the pump, signal and idler waves in the process of FWM, additionally taking into account the effects of SPM and XPM, are investigated. A comparison between the obtained results has been made. It is shown that the effects of self-phase modulation and cross-phase modulation increase the period of energy exchange. Full article

Polydimethylsiloxane (PDMS) films doped with graphene nanoplatelets (GNP) with an embossed surface-relief grating were investigated as photothermal actuated sensors. The films were initially characterized using controlled environmental heating where the wavelength of a diffracted white-light probe beam measured at a fixed angle increased monotonically with temperature due to thermal expansion of the grating. An asymmetric double sigmoidal function tracked the shift in peak diffraction wavelength. The observed thermal response is consistent with the thermal expansion of a freestanding PDMS composite film. When a continuous-wave (CW) laser was incident on the film, intensity-dependent photothermal expansion caused a transient deformation in the grating. The photomechanical behavior of the grating, tracked by the diffracted probe beam with a miniature spectrometer, was then shown to act as a laser power meter. These results demonstrate that photomechanical materials can be used as add-ons to existing optical spectroscopy devices for power-sensing applications. Full article

Combined pulse laser systems combining continuous-wave (CW) lasers and nanosecond pulsed lasers have shown clear advantages in metal ablation and surface modification. However, the plasma shielding effect induced by nanosecond pulses and the associated shock-wave phenomena in hybrid laser systems remain insufficiently investigated, particularly regarding their influence on CW laser energy coupling. In this study, the ablation behavior of metal targets under the combined irradiation of a 500 W CW laser and nanosecond pulsed lasers with pulse energies ranging from 0.4 J to 1.0 J was investigated. High-speed plasma imaging was employed to analyze laser–material interaction characteristics, including absorption behavior and molten material ejection, while high-speed infrared thermography was used to monitor transient temperature evolution during combined pulse laser processing. Macroscopic and microscopic analyses were conducted to characterize damage morphology, and a three-dimensional surface profilometer was used to quantitatively evaluate ablation efficiency. The results show that, under combined pulse laser irradiation, the removed volume increased from 0.05 mm³ to 0.618 mm³ and the ablation depth increased from 0.136 mm to 0.776 mm. Compared with CW laser processing alone, the ablation efficiency was markedly enhanced. This improvement is attributed to the combined effects of optimized energy deposition, thermal distribution, and material response. In addition, the plasma shielding effect was observed to vary with nanosecond pulse energy, indicating that precise energy control is critical for performance enhancement. This study demonstrates the potential of combined pulse laser technology for high-efficiency and high-precision metal surface processing and micro–nano fabrication. Full article

The integrated III-V self-injection locked (SIL) laser exhibits excellent linewidth compression, noise reduction, and frequency stability. However, the laser’s low efficiency and fluctuating output power severely limit its applications in optical coherent transmission, light detection and ranging (LiDAR), spectroscopy, and so on. Based on the rate equations for a semiconductor laser coupled to counter-propagating fields in a micro-ring resonator (MRR), we systematically investigate the laser power and linewidth compression under self-locking conditions. We improve the slope efficiency by adjusting the injection phase, diode–MRR coupling efficiency, the normalized mode-coupling rate between clockwise (CW) and counter-clockwise (CCW) modes, and the MRR Q-factor. The results show that the enhanced diode–MRR coupling efficiency effectively increases the laser slope efficiency and improves the stability of the injection phase and feedback intensity. The injection phase significantly influences the range of the self-injection locked state. The normalized mode-coupling rate effectively affects the locking bandwidth and maintains stable power transfer. The MRR intrinsic Q-factor has a positive correlation with improving the laser slope efficiency and compressing the linewidth. Full article

This work presents a combined numerical and experimental investigation into the laser machining of aluminum alloy Al 1050 H14 using a high-power Continuous Wave (CW) fiber laser. Advanced three-dimensional, coupled thermal–structural Finite Element Method (FEM) simulations are developed to model key laser–material interaction processes, including laser-induced plastic deformation, laser etching, and engraving. Cases for both static single-shot and dynamic linear scanning laser beams are investigated. The developed numerical models incorporate a Gaussian heat source and the Johnson–Cook constitutive model to capture elastoplastic, damage, and thermal effects. The simulation results, which provide detailed insights into temperature gradients, displacement fields, and stress–strain evolution, are rigorously validated against experimental data. The experiments are conducted on an integrated setup comprising a 2 kW TRUMPF CW fiber laser hosted on a 3-axis CNC milling machine, with diagnostics including thermal imaging, thermocouples, white-light interferometry, and strain gauges. The strong agreement between simulations and measurements confirms the predictive capability of the developed FEM framework. Overall, this research establishes a reliable computational approach for optimizing laser parameters, such as power, dwell time, and scanning speed, to achieve precise control in metal surface treatment and modification applications. Full article

We propose a novel scheme for generating high-frequency millimeter-wave signals by exploiting period-one (P1) dynamics in a mutual injection configuration of two spin-polarized vertical-cavity surface-emitting lasers (spin-VCSELs). The frequency of the generated millimeter-wave signal is jointly determined by the birefringence rate of the spin-VCSEL and the frequency detuning between the two lasers. By leveraging the complex dynamics of free-running spin-VCSELs, we explore the coupling of three distinct dynamic states: continuous-wave (CW) injected into CW, CW injected into P1 oscillation, and P1 oscillation injected into P1 oscillation. Our results reveal that these interactions not only enhance the tunability and frequency of the millimeter-wave output but also significantly reduce the linewidth, offering substantial advantages for reconfigurable photonic systems. This study demonstrates the remarkable potential of mutually injected spin-VCSELs for generating high-performance, tunable photonic millimeter waves and highlights their promising applications in advanced communication and radar systems. Full article

In the context of Industry 4.0, new methods of manufacturing, monitoring, and data generation related to industrial processes have emerged. Over the last decade, a new method of part manufacturing that has been revolutionizing the industry is Additive Manufacturing, which comes in various forms, including the more traditional Fusion Deposition Modeling (FDM) and the more innovative ones, such as Laser Metal Deposition (LMD) and Wire Arc Additive Manufacturing (WAAM). New technologies related to monitoring these processes are also emerging, such as Cyber-Physical Systems (CPSs) or Digital Twins (DTs), which can be used to enable Artificial Intelligence (AI)-powered analysis of generated big data. However, few works have dealt with a comprehensive data analysis, based on Digital Twin systems, to study quality levels of manufactured parts using 3D models. With this background in mind, this current project uses a Digital Twin-enabled dataflow to constitute a basis for a proposed data analysis pipeline. The pipeline consists of analyzing metal AM-manufactured parts’ surface roughness quality levels by the application of a Deep Neural Network (DNN) analytical model and enabling the assessment and tuning of deposition parameters by comparing AM-built models’ 3D representation, obtained by photogrammetry scanning, with the positional data acquired during the deposition process and stored in a cloud database. Stored and analyzed data may be further used to refine the manufacturing of parts, calibration of sensors and refining of the DT model. Also, this work presents a comprehensive study on experiments carried out using the CW-GTAW (Cold Wire Gas Tungsten Arc Welding) process as the means of depositing metal, resulting in hollow parts whose geometries were evaluated by means of both 3D scanned data, obtained via photogrammetry, and positional/deposition process parameters obtained from the Digital Twin architecture pipeline. Finally, an adapted PointNet DNN model was used to evaluate surface roughness quality levels of point clouds into 3 classes (good, fair, and poor), obtaining an overall accuracy of 75.64% on the evaluation of real deposited metal parts. Full article

As high-end equipment manufacturing advances, demand for improved surface performance in critical components has increased. Laser cladding is an advanced surface strengthening technique that affords effective surface modification. During the laser cladding process, obtaining a fine grain microstructure usually helps to enhance the microhardness, wear resistance, and corrosion resistance of the cladding layer. However, conventional laser cladding often yields coarse columnar grains that limit further performance improvements, so process optimization to achieve grain refinement is necessary. In this study, oscillating laser cladding was combined with a pulsed-wave (PW) laser mode to deposit a fine-grained Al₂CrFe₂Ni₄Ti_1.5 high-entropy alloy cladding on Q550 steel substrates. Compared with continuous-wave (CW) laser cladding, the PW mode produced markedly refined grains and concomitant improvements in microhardness, wear resistance, and corrosion resistance. Specifically, the microhardness of the PW cladding layer reached approximately 673.34 HV_0.5, the wear volume was approximately 0.06 mm³, the wear rate was approximately 0.21 × 10⁻⁴ mm³/N·m, and the corrosion current density decreased to approximately 1.212 × 10⁻⁵ A·cm⁻². This work presents a novel approach for producing high-performance, wear-resistant, and corrosion-resistant high-entropy alloy cladding layers, and offers both theoretical insight and potential engineering applications. Full article

By employing graded-interfaces modeling, ~10 μm-emitting quantum cascade lasers (QCLs) are designed with previously found conditions for record-high wall-plug efficiency (WPE) operation of mid-infrared QCLs: direct resonant-tunneling injection from a prior-stage low-energy state into the upper-laser level, photon-induced carrier transport, and carrier-leakage suppression via the step-taper active-region (STA) approach. For devices with interface-roughness (IFR) parameters characteristic of optimized molecular-beam-epitaxy (MBE) growth, a maximum front-facet pulsed WPE value of 19.6% is projected for 60-stages STA-type devices. This results from several factors: 19 mV voltage defect at threshold, 72% voltage efficiency at the maximum WPE point, and ~93% injection efficiency due to strong carrier-leakage suppression. 2.7 W peak front-facet power is projected. For devices with our metal–organic chemical vapor deposition (MOCVD)-growth IFR parameters, the projected maximum pulsed WPE value is 17.1%, i.e., 1.7 times higher than the highest reported front-facet WPE value from ~10 μm-emitting MOCVD-grown QCLs. Studies regarding the WPE value variation with the stage number, while employing waveguide designs having the same empty cavity loss, reveal that the maximum WPE value remains almost the same for 50–60 stages devices. In turn, there is potential for obtaining significantly higher CW powers than from conventional ~10 μm-emitting QCLs. Full article

Since direct laser surface texturing of polymers is an emerging area, considerable attention is given to this technique with the aim of forming a basis for follow-up research that could open the way for potential technological ideas and optimization in novel applications. Laser pre-processing of ballistic textiles can raise surface roughness of smooth para-aramid fibres and as a result can improve the adhesion of functional coatings applied in following processing steps, thus opening new possibilities for material performance improvement. The impact resistance of ballistic fabric depends on the ability of its yarns in contact with the projectile absorb energy locally and disperse it to adjacent yarns without undergoing severe damage or failure. In addition to the yarn deformation and fracture, yarn resistance to pull-out contributes to the dissipation of impact energy significantly. The objective of this study is to optimize Kevlar^® KM2+ fabric surface topographies by adjusting the continuous wave (CW) CO₂ laser parameters in such a way that it increases the surface roughness and resistance to the yarn pull-out from the fabric without destroying the unique structure of the of Kevlar^® KM2+ fibres. Experimental research measured data show increase in surface roughness by 50–53% and set of laser parameter variants have been obtained that allow for an increase in KM2+ 440D woven fabric yarns pull out force from fabric in the range from 50% up to 99% compared to the untreated one. Full article

This work investigates the performance of a polyvinyl alcohol/acrylamide-based photopolymer (PVA/AA) under pulsed and continuous-wave (CW) laser exposure for holographic recording. Using a versatile setup that allows direct comparison between both regimes, diffraction efficiency (DE), angular responses, and material parameters were analyzed. Comparable maximum DE was achieved with both CW and pulsed laser exposure; however, the pulsed regime produces stronger attenuation along the grating depth, which emphasizes the need to lower the dye concentration. Furthermore, the temporal evolution of DE reveals a smaller influence of oxygen inhibition under CW exposure. Finally, second-order angular reconstructions confirm that pulsed gratings exhibit a better sinusoidal modulation, especially at low frequency rates. These results enhance the understanding of how pulsed exposure affects holographic recording and open pathways for optimizing photopolymer systems in advanced technologies. Full article

Carbon deposits on the crown of engine pistons can markedly reduce combustion efficiency and shorten service life. Conventional cleaning techniques often fail to simultaneously ensure a high carbon removal efficiency and maintain optimal surface integrity. To enable efficient and precise carbon removal, this study proposes the application of hybrid laser cleaning—combining continuous-wave (CW) and pulsed lasers—to piston carbon deposit removal, and employs response surface methodology (RSM) for multi-objective process optimization. Using the N52B30 engine piston as the experimental substrate, this study systematically investigates the combined effects of key process parameters—including CW laser power, pulsed laser power, cleaning speed, and pulse repetition frequency—on surface roughness (Sa) and carbon residue rate (RC). Plackett–Burman design was employed to identify significant factors, the method of the steepest ascent was utilized to approximate the optimal region, and a quadratic regression model was constructed using Box–Behnken response surface methodology. The results reveal that the Y-direction cleaning speed and pulsed laser power exert the most pronounced influence on surface roughness (F-values of 112.58 and 34.85, respectively), whereas CW laser power has the strongest effect on the carbon residue rate (F-value of 57.74). The optimized process parameters are as follows: CW laser power set at 625.8 W, pulsed laser power at 250.08 W, Y-direction cleaning speed of 15.00 mm/s, and pulse repetition frequency of 31.54 kHz. Under these conditions, the surface roughness (Sa) is reduced to 0.947 μm, and the carbon residue rate (RC) is lowered to 3.67%, thereby satisfying the service performance requirements for engine pistons. This study offers technical insights into the precise control of the hybrid laser cleaning process and its practical application in engine maintenance and the remanufacturing of end-of-life components. Full article

In this work, we present a high-performance tapered quantum cascade laser (QCL) designed to achieve both high output power and low divergence angle. By integrating a tapered waveguide with a Fabry–Perot structure, significant improvements of tapered QCL devices in both output power and beam quality are demonstrated. The optimized 50 µm wide tapered QCL achieved a maximum output power of 2.76 W in pulsed operation with a slope efficiency of 3.52 W/A and a wall-plug efficiency (WPE) of 16.2%, while reducing the divergence angle to 13.01°. The device maintained a maximum power of 1.34 W with a WPE exceeding 8.2%, measured under room temperature and continuous wave (CW) operation. Compared to non-tapered Fabry–Perot QCLs, the tapered devices exhibited a nearly 10-fold increase in output power and over 200% improvement in WPE. This work provides a promising pathway for advancing mid-infrared laser technology, particularly for applications requiring high power, low divergence, and temperature stability. Full article

Monolayer (ML) molybdenum disulfide (MoS₂) is a typical valleytronic material which has important applications in, for example, polarization optics and information technology. In this study, we examine the effect of continuous wave (CW) laser pumping on the basic optoelectronic properties of ML MoS₂ placed on a sapphire substrate, where the pump photon energy is larger than the bandgap of ML MoS₂. The pump laser source is provided by a compact semiconductor laser with a 445 nm wavelength. Through the measurement of THz time-domain spectroscopy, we obtain the complex optical conductivity for ML MoS₂, which are found to be fitted exceptionally well with the Drude–Smith formula. Therefore, we expect that the reduction in conductivity in ML MoS₂ is mainly due to the effect of electronic backscattering or localization in the presence of the substrate. Meanwhile, one can optically determine the key electronic parameters of ML MoS₂, such as the electron density n_e, the intra-band electronic relaxation time τ, and the photon-induced electronic localization factor c. The dependence of these parameters upon CW laser pump intensity is examined here at room temperature. We find that 445 nm CW laser pumping results in the larger n_e, shorter τ, and stronger c in ML MoS₂ indicating that laser excitation has a significant impact on the optoelectronic properties of ML MoS₂. The origin of the effects obtained is analyzed on the basis of solid-state optics. This study provides a unique and tractable technique for investigating photo-excited carriers in ML MoS₂. Full article

In this study, we describe the preparation of carbon dots (CDs) from natural charcoal by laser ablation in a liquid. A continuum wave (CW) laser diode operating at a wavelength of 450 nm, hitting a solid carbon target placed into a biocompatible liquid, constituted of a phosphate-buffered saline (PBS) solution and distilled water, was used for the generation of the CDs suspension. Exploring the practical applications of carbon dots, it was observed that the luminescence of the produced CDs can be used as bioimaging in living organisms, environmental monitoring, chemical analysis, targeted drug delivery, disease diagnosis, therapy, and others. The CDs’ luminescence can be induced by UV irradiation and, as demonstrated in this study, by energetic MeV proton beams. The fluorescence was revealed mainly at 480 nm when UV illuminated the CDs, and also in the region at 514–642 nm when the CDs were irradiated by energetic proton ions. Atomic force microscopy (AFM) of the CD films revealed their spherical shape with a size of about 10 nm. The significance of the manuscript lies in the use of CDs produced by laser ablation exhibiting luminescence under irradiation of an energetic proton beam. Full article