Search Results (19)

This study used 347H heat-resistant steel as the base material and systematically investigated the microstructural evolution and second-phase precipitation in typical regions during welding and aging processes. The results showed that the weld metal consisted of austenitic dendrites and inter-dendritic ferrite in a lath-like form. In the welded samples, the HAZ (Heat-Affected Zone) and BM (Base Material) regions were composed of equiaxed crystals. The microhardness of the HAZ was lower, mainly due to the coarser grain size and fewer second-phase particles. After aging at 700 °C, the hardness of all regions of the welded joint increased significantly due to the precipitation of M₂₃C₆ and MX phases. When the aging temperature increased to above 800 °C, the stability of the M₂₃C₆ phase decreased, and the diffusion rate of Nb in the matrix accelerated, promoting the preferential growth and stable presence of the MX phase. As the MX phase competes with the M₂₃C₆ phase for carbon during its formation, its generation suppresses the further precipitation of the M₂₃C₆ phase. Under 800 °C aging conditions, the γ/δ interface exhibited high interfacial energy, and the Nb content in the ferrite was higher, which facilitated the formation of the MX phase along this interface. As the aging temperature continued to rise, the hardness of the HAZ and BM regions initially increased and then decreased. After aging at 800 °C, the hardness decreased because the M₂₃C₆ phase no longer precipitated. After aging at 900 °C, the hardness of the HAZ and BM regions significantly increased, mainly due to the large precipitation of the MX phase. The hardness of the W (Weld Zone) and FZ (Fusion Zone) regions gradually decreased with the increase in aging temperature, mainly due to the reduction of inter-dendritic ferrite content, coarsening of second-phase particles, weakening of the pinning effect, and grain growth. In the 900 °C aging samples, the MX phase particle size from largest to smallest was as follows: W > HAZ > BM. The Nb-enriched ferrite provided the chemical driving force for the precipitation of the MX phase, while the δ/γ interface provided favorable conditions for its nucleation and growth; thus, the MX phase particles were the largest in the W region. The HAZ region, due to residual stress and smaller grain boundary area, had MX phase particle size second only to the W region. Full article

The effect of thermal hydrogen charging on the tensile properties of GH625 superalloy was investigated. The results reveal that hydrogen significantly reduces the ductility of the GH625, leading to a shift from microvoid coalescence (MVC)-induced ductile fracture to intergranular (IG) brittle fracture. Random grain boundaries (GBs) are the primary sites for crack initiation. Hydrogen reduces the critical fracture stress of the δ phase at grain boundaries, causing cracking of the δ phase. Under the influence of hydrogen-enhanced localized plasticity (HELP) and hydrogen-enhanced decohesion (HEDE), the δ/γ interface debonds, forming microcracks that propagate along the fractured δ phase, leading to intergranular cracking. Annealing twin boundaries (TBs) serve as secondary sites for crack initiation. Hydrogen-induced local stress concentration promotes twin boundary sliding and hydrogen segregation reduces twin boundary cohesion strength, which is the primary cause of TB crack formation. Full article

This study investigated the efficacy of three spray adjuvants (Coerce, Wetcit, and Silwet408) in enhancing dinotefuran permeation in rice leaves. Different concentrations of these adjuvants were tested using an external standard method. The rice leaf surface was analyzed by using the van Oss–Chaudhury–Good method to establish a link between surface free energy (SFE) and dinotefuran permeation. All of the adjuvants effectively increased dinotefuran permeation in rice leaves, with the highest permeation of 8.496 mg/kg achieved using Wetcit at 1000 mg/L. The SFE of the rice leaf surface was determined to be 29.28 mJ/m². A notable correlation was observed between the energy difference (the SFE of the pesticide liquid versus the SFE of the rice leaf surface) and permeation. Various fitting methods, including linear, exponential, logarithmic, polynomial, and power methods, were applied. Polynomial fitting demonstrated the highest coefficient of determination (R² > 0.9000). The relationship between the permeation (y) and energy difference (Δγ) conformed to the polynomial equation y = aΔγ² + bΔγ + c, where a, b, and c are constants. This model provides a predictive tool for the optimal dosage of spray adjuvants according to target plant characteristics, enhancing the understanding of the interaction between pests and pesticides. Full article

Protein phosphatase 2A (PP2A) functions as a tumor suppressor and consists of a scaffolding, catalytic, and regulatory subunit. The B56 gene family of regulatory subunits impart distinct functions onto PP2A. Codon usage bias (CUB) involves the selection of synonymous codons, which can affect gene expression by modulating processes such as transcription and translation. CUB can vary along the length of a gene, and differential use of synonymous codons can be important in the divergence of gene families. The N-termini of the gene product encoded by B56α possessed high CUB, high GC content at the third codon position (GC3), and high rare codon content. In addition, differential CUB was found in the sequence encoding two B56γ N-terminal splice forms. The sequence encoding the N-termini of B56γ/γ, relative to B56δ/γ, displayed CUB, utilized more frequent codons, and had higher GC3 content. B56α mRNA had stronger than predicted secondary structure at their 5′ end, and the B56δ/γ splice variants had long regions of weaker than predicted secondary structure at their 5′ end. The data suggest that B56α is expressed at relatively low levels as compared to the other B56 isoforms and that the B56δ/γ splice variant is expressed more highly than B56γ/γ. Full article

Quartz crystal microbalance with dissipation monitoring (QCM-D) is a well-established technique for studying soft films. It can provide gravimetric as well as nongravimetric information about a film, such as its thickness and mechanical properties. The interpretation of sets of overtone-normalized frequency shifts, ∆f/n, and overtone-normalized shifts in half-bandwidth, ΔΓ/n, provided by QCM-D relies on a model that, in general, contains five independent parameters that are needed to describe film thickness and frequency-dependent viscoelastic properties. Here, we examine how noise inherent in experimental data affects the determination of these parameters. There are certain conditions where noise prevents the reliable determination of film thickness and the loss tangent. On the other hand, we show that there are conditions where it is possible to determine all five parameters. We relate these conditions to the mathematical properties of the model in terms of simple conceptual diagrams that can help users understand the model’s behavior. Finally, we present new open source software for QCM-D data analysis written in Python, PyQTM. Full article

A process control agent is an organic additive used to regulate the balance between fracturing and mechanical kneading, which control the size of the as-milled particles. Tributyl phosphate (TBP) is evaluated to act as surface modifier of PbTe, and it is compared with the results obtained using formaldehyde (CH₂O). In order to elucidate the nature of the interaction between TBP and the PbTe surface, global and local descriptors were calculated via the density functional theory. First, TBP and CH₂O molecules are structurally optimized. Then, vertical ionization energies as well as vertical electron affinities are calculated to elucidate how both molecules behave energetically against removal and electron gain, respectively. The results were compared with those obtained from the electrostatic potential mapped on the van der Waals isosurface. It is inferred that the theoretical insights are useful to propose adsorption modes of TBP and CH₂O on the PbTe surface, which are usable to rationalize the facets exposed by PbTe after the surface treatment. The optimized structures of the compound systems showed a close correlation between the surface energy shift (Δγ) and the PbTe facets exhibited. Finally, a Wulff construction was built to compare the usage of TBP and CH₂O molecules in PbTe morphology. Full article

The main purpose of this paper is to analyze the influence of different types of alignment errors on the meshing performance of loaded straight bevel gears. Based on 3D finite element models of the specific loaded assembling straight bevel gear pair, the contact area, transmission error, vibration and noise for the specific loaded straight bevel gear are investigated. The results show that the alignment errors have different degrees of adverse effects on the contact area and the contact line of the straight bevel gear pair, which can affect the transmission error, vibration, and noise of the straight bevel gear drives. The results also demonstrate that the most dangerous type of combined alignment errors is ΔP, ΔG, ΔE < 0 and Δγ. The results of this research can provide theoretical guidelines for the assembly and modification of straight bevel gears. Full article

In this work, a multi-phase cellular automaton (CA) model is extended for the quantitative simulation of peritectic phase transition. First, the effects of cooling rate/supersaturation and temperature on the peritectic transformation kinetics in Fe-C alloys are investigated by utilizing the present CA model. The CA simulations show that supersaturations in the parent phases (liquid and δ-ferrite) increase the L/γ interface growth velocity remarkably, but tinily for the δ/γ interface migration velocity. There exists a transition supersaturation for isothermal transformations, at which the growth rates of the two interfaces are equal. The transition supersaturation is found to increase with decreasing temperature. Microstructural evolution at different cooling rates during peritectic transformation is simulated using the experimental conditions. At low cooling rates, the δ/γ interface propagates at a higher velocity than the L/γ interface. At high cooling rates, however, the γ-phase grows more into the L-phase with a cellular morphology. Then, the proposed CA model is applied to simulate the microstructural evolution during peritectic reaction. It is observed that the γ-phase propagates along the L/δ interface and finally encircles the δ-phase. Meanwhile, the intervenient γ-phase grows in thickness through peritectic transformation. The CA simulations are compared reasonably well with the experimental data and analytical calculations. Full article

The microstructural evolution and mechanical behavior of cast duplex stainless steels (CDSSs) at 400 °C for different thermal aging times were investigated by transmission electron microscope (TEM) and small punch test (SPT). The results showed that the spinodal decomposition in ferrite was the main reason for the decrease in toughness, and G-phase did not play an important role in the embrittlement process. The change of membrane stretching zone (W_m) played an important role in the SPT load-displacement curve before and after thermal aging. During the deformation process of W_m in the SPT, for thermal aging for 10,000 h, some completely curved slip bands were generated inside the ferrite phase, which had no contact with the δ/γ phase interface and belonged to the slip bands produced by the independent deformation of ferrite. The combined effect of the curved slip bands and stress concentration led to the initiation of obvious micro-cracks at the δ/γ phase interface. The micro-cracks propagated along the ferrite phase curved slip bands, and eventually penetrated the entire hardened ferrite phase. Full article

Based on the predicted phase diagram of super duplex stainless steel (DSS) calculated by Thermo-Calc, the maximum peak temperature 1100 °C was selected to ensure no σ phase existence. This target temperature fell into the two-phase solid solution (SS) region. A series of different thermal cycling tests were carried out with the notations of 2SS, 2SS + 3 cycles, 2SS + 7 cycles, 2SS + 13 cycles, and 2SS + 20 cycles. It was found that the trend of two-phase volume ratio variation by thermal cycling followed the predicted thermodynamic equilibrium trend. After 2SS + 7 cycles, the ratio of two-phase δ/γ tended toward the ideal 1:1. According to the electron backscatter diffraction (EBSD) analysis, the δ phase crystal orientation changed from the most frequent directions of <001> and <111> of the as-received sample to the most frequent orientation of <113> after two SS treatments. While the γ phase grain always remained at <101> orientation. The grain boundary misorientation angles of the γ grains were relatively stable, ranging from 53° to 63°, but those of the δ grains were widely distributed actively presuming the lattice rotation. The Kernel Average Misorientation (KAM) value of the local strain in face center cubic (fcc) γ grains was varied and greater than that of the body center cubic (bcc) δ phase, indicating that the former, with a large grain boundary misorientation had larger local deformation than the latter, which possesses wide random misorientation angle distribution. Full article

A quartz crystal microbalance (QCM) is described, which simultaneously determines resonance frequency and bandwidth on four different overtones. The time resolution is 10 milliseconds. This fast, multi-overtone QCM is based on multi-frequency lockin amplification. Synchronous interrogation of overtones is needed, when the sample changes quickly and when information on the sample is to be extracted from the comparison between overtones. The application example is thermal inkjet-printing. At impact, the resonance frequencies change over a time shorter than 10 milliseconds. There is a further increase in the contact area, evidenced by an increasing common prefactor to the shifts in frequency, Δf, and half-bandwidth, ΔΓ. The ratio ΔΓ/(−Δf), which quantifies the energy dissipated per time and unit area, decreases with time. Often, there is a fast initial decrease, lasting for about 100 milliseconds, followed by a slower decrease, persisting over the entire drying time (a few seconds). Fitting the overtone dependence of Δf(n) and ΔΓ(n) with power laws, one finds power-law exponents of about 1/2, characteristic of semi-infinite Newtonian liquids. The power-law exponents corresponding to Δf(n) slightly increase with time. The decrease of ΔΓ/(−Δf) and the increase of the exponents are explained by evaporation and formation of a solid film at the resonator surface. Full article

Tenalisib (RP6530), a dual phosphoinositide 3-kinase δ/γ inhibitor was evaluated in a phase I/Ib study for maximum tolerated dose (MTD), pharmacokinetics, and efficacy in patients with relapsed/refractory peripheral and cutaneous T-Cell Lymphoma (TCL). Histologically confirmed (TCL) patients, with ≥1 prior therapy received Tenalisib orally in a 28-day cycle in doses of 200 to 800 mg twice daily (800 mg in fasting and fed state) in escalation phase (n = 19) and 800 mg twice daily (fasting) in expansion phase (n = 39). The most frequently reported treatment emergent adverse events (TEAE) and related TEAE were fatigue (45%) and transaminase elevations (33%), respectively. Most frequently reported related Grade ≥3 TEAE was transaminase elevation (21%). Two dose-limiting toxicities occurred in the 800 mg fed cohort; hence, 800 mg fasting dose was deemed MTD. Tenalisib was absorbed rapidly with a median half-life of 2.28 h. Overall response rate in 35 evaluable patients was 45.7% (3 complete response (CR); 13 partial response (PR)) and median duration of response was 4.9 months. Responding tumors showed a marked downregulation of CD30, IL-31 and IL-32α. With an acceptable safety and promising clinical activity, Tenalisib can be a potential therapeutic option for relapsed/refractory TCL. Currently, a phase I/II combination study with romidepsin is ongoing. Full article

The deformation behavior and fracture mechanism of cast duplex stainless steel tubular specimens under different tensile stages were investigated through experimental and numerical evaluation. The results showed that the axial stress was redistributed due to the necking of the tubular specimen, the axial stress near the internal wall was larger than those near the external wall, and its maximum axial stress was distributed between the internal wall and the center of the wall thickness. Microcracks and voids were initiated under the maximum shear stress along the δ/γ phase interface and propagated to the ferrite interior. The voids were connected and merged into the main crack through the propagation of the microcracks. Moreover, the main crack first propagated to the internal wall and then rapidly propagated to the external wall. The fracture morphology can be divided into three types: shear lip zones that can be found on both the internal and external walls, and shear lip zones that can be found on either only the internal wall or the external wall. Full article

Duplex stainless steels (DSSs) are complex materials and they have been widely used in the marine environment and gas industries, primarily offering a better resistance of pitting corrosion and good mechanical properties. In the present work, the effects of heat treatment on duplex stainless steel (DSS) weld overlay samples that were heat treated at three different temperatures, namely 350 °C, 650 °C, and 1050 °C, and followed by air cooling and water quenching were studied. Stress relief temperature at 650 °C had induced sigma phase precipitation in between delta ferrite and austenite (δ/γ) grain boundaries, resulting in the loss of corrosion resistance in the weld metal. Interestingly, post weld heat treatment (PWHT) test samples that were reheated to solution annealing temperature had shown no weight loss. The ferrite count determination in the region of weld metal overlay increased at hydrogen relief and decreased at stress relief temperatures due to slow cooling, which is more favorable to austenite formation. The amount of ferrite in the weld metals was significantly reduced with the increment of solution anneal temperature to 1050 °C because of sufficient time for the formation of austenite and giving optimum equilibrium fraction in the welds. Full article

In the continuous casting process, the shrinkage of the peritectic phase transition during the initial solidification process has an important influence on the surface quality of peritectic steel. The initial solidification process of 0.10C%, 0.14C%, and 0.16C% peritectic steels was observed in situ by a high temperature laser confocal microscope, and the contraction degree during initial solidification was characterized by surface roughness. The results showed that under the cooling rate of 20 °C/s, the surface roughness value Ra(δ/γ) of 0.10C% peritectic steel was 32 μm, the Ra(δ/γ) value of 0.14C% peritectic steel was 25 μm, and the Ra(δ/γ) value of 0.16C% peritectic steel was 17 μm. With increasing carbon content, the contraction degree of the δ→γ transformation decreased, and the value of the surface roughness Ra(δ/γ) declined. Therefore, surface roughness can characterize the contraction degree of the δ→γ transformation in the initial solidification process of peritectic steel under the condition of a large cooling rate. Full article