Search Results (18)

The development of food packaging materials that reduce the production of plastic, preserving at the same time the quality of food, is a topic of great interest today for the scientific community. Therefore, this article aims to report the effectiveness of an eco-friendly packaging material based on alginic acid and grape pomace extract from Vitis vinifera L. (winemaking by-products) for storing red meat in a domestic refrigerator. Specifically, biogenic amines are considered “sentinels” of the putrefactive processes, and their presence was thus monitored. For this purpose, an experimental analytical protocol based on the use of solid-phase microextraction coupled with gas chromatography–mass spectrometry was developed during this work for the determination of six biogenic amines (butylamine, cadaverine, isobutylamine, isopentylamine, putrescine, and tyramine). Moreover, by combining the analytical results with those of pH and weight loss measurements, differential scanning calorimetry, and microbiological analysis, it was proved that the studied materials could be proposed as an alternative packaging material for storing foods of animal origin, thus lowering the environmental impact according to sustainability principles. Full article

Water-resistant and environmentally friendly sodium-alginate-based films have been investigated to develop functional materials to extend the food’s shelf-life. A water-stable alginate-based film was prepared, employing both the internal and external gelation approach in the presence of CaCl₂. To apply this film to food packaging and thus preserve food quality, the aim of this work is to perform a chemical and physical characterization of the proposed materials, evidencing the main features and stability under different work conditions. Water contact angle measurements showed a value of 65°, suggesting an important reduced hydrophilic character of the obtained alginate films due to the novel CaCl₂-induced compacted polymer network. The film’s stability was thus checked through swelling measurements in water after varying pH, temperature, and ionic strength. The film was stable at high temperatures and not pH-responsive. Only highly concentrated salt-based solutions negatively affected the proposed packaging, causing a large swelling. Furthermore, a water-based polyphenolic extract from grape (Vitis vinifera L.) pomace waste was embedded inside the films in different amounts in order to confer additional properties. The extract’s polyphenolic content (evaluated from HPLC/MS-MS measurements) endowed the films’ UV-light screening and enhanced antioxidant properties. These important findings suggest the additional potential role of these films in protecting food from light deterioration. The stability of these hybrid films was also checked by observation, as the polyphenols’ presence did not largely alter the alginate network that occurred yet was water-resistant under the described work conditions. Full article

In this work, the great performance of chitosan-based films blended with TiO₂ (CH/TiO₂) is presented to adsorb the hazardous pollutant 2,4-dinitrophenol (DNP) from water. The DNP was successfully removed, with a high adsorption %: CH/TiO₂ exhibited a maximum adsorption capacity of 900 mg/g. For pursuing the proposed aim, UV–Vis spectroscopy was considered a powerful tool for monitoring the presence of DNP in purposely contaminated water. Swelling measurements were employed to infer more information about the interactions between chitosan and DNP, demonstrating the presence of electrostatic forces, deeply investigated by performing adsorption measurements by changing DNP solutions’ ionic strength and pH values. The thermodynamics, adsorption isotherms, and kinetics were also studied, suggesting the DNP adsorption’s heterogeneous character onto chitosan films. The applicability of pseudo-first- and pseudo-second-order kinetic equations confirmed the finding, further detailed by the Weber–Morris model. Finally, the adsorbent regeneration was exploited, and the possibility of inducing DNP desorption was investigated. For this purpose, suitable experiments were conducted using a saline solution that induced the DNP release, favoring the adsorbent reuse. In particular, 10 adsorption/desorption cycles were performed, evidencing the great ability of this material that does not lose its efficiency. As an alternative approach, the pollutant photodegradation by using Advanced Oxidation Processes, allowed by the presence of TiO₂, was preliminary investigated, opening a novel horizon in the use of chitosan-based materials for environmental applications. Full article

Using a water-insoluble β-cyclodextrin-epichlorohydrin copolymer (β-EPI) as an adsorbent to remove carbamazepine (CBZ), an anti-epileptic drug often found both in hospital and urban wastewater, has been validated. The effect of several physicochemical parameters on CBZ retention onto β-EPI, such as contact time, adsorbent dosage, CBZ initial concentration, pH, salts, and temperature, was assessed. The adsorption process occurs in a very short time, less than 20 min, and depends on CBZ concentration and β-EPI amount used. Changes in pH and salt presence, regardless of the type of cation or anion used, do not significantly affect the system’s efficiency. Desorption experiments were also performed, and methanol has proven to be the best CBZ extraction medium; it was also found that the polymer can be recovered and reused for at least five cycles, which makes it cheap and environmentally friendly. Advanced oxidation processes were also tested for CBZ removal by synthesizing a β-EPI polymer bearing titanium dioxide for adsorption and consecutive photocatalytic degradation of the retained pollutant directly onto the material; the effect of TiO₂ amount in the polymer on CBZ oxidation was evaluated. These experiments highlighted the system’s effectiveness, and it was also observed that the H₂O₂ presence in the solution enhanced the CBZ photodegradation. Full article

This work aims to characterize the adsorption process of propranolol HCl, an emerging pollutant and a widely used β-blocker, onto kiwi peels, an agricultural waste. The use of UV-vis spectroscopy was considered to obtain information about the pollutant removal working in the in-batch mode. In a relatively short time, the adsorption process could remove the pollutant from water. A kiwi peel maximum adsorption capacity of 2 mg/g was obtained. With the perspective of scaling up the process, preliminary in-flux measurements were also performed. The investigation of the whole in-batch adsorption process was conducted by studying the effect of ionic strength (adopting salt concentrations from 0 to 0.4 M), pH values (from 2 to 12), adsorbent/pollutant amounts (from 25 to 100 mg and from 7.5 to 15 mg/L, respectively), and temperature values (from 289 to 305 K). The thermodynamics, the adsorption isotherms, and the kinetics of the adsorption process were also carefully investigated. The Langmuir model fitted the experimental data well, with an R² of 0.9912, restituting K_L: 1 L/mg and Q₀: 1.8 mg/g. The temperature increase enhanced the pollutant removal due to the endothermic adsorption characteristics. Accordingly, a ΔH°_298K of +70 KJ/mol was obtained. The pseudo-first-order kinetic model described the process. Due to the results observed during the study of the effects of pH and ionic strength, the prominent presence of electrostatic interactions, working in synergy with hydrophobic forces and H-bonds between the pollutant and kiwi peel surfaces, was successfully demonstrated. In particular, FTIR-ATR measurements confirmed the latter findings. Finally, desorption experiments for recycling 100% of propranolol for each cycle were performed using 0.1 M MgCl₂. Ten cycles of adsorption/desorption were obtained and indicated that the percentage of propranolol removal was not affected during each run, increasing the maximum adsorption from 2 to 20 mg/g. Full article

During the last decades, the demand for processes developed according to the Circular Economy Principles has increased, searching for an alternative life for wastes. For this purpose, a one-pot green approach is exploited during this work to synthesize gold nanoparticles (AuNPs) by using grape pomace waste from Vitis vinifera. A raw aqueous extract of grape seeds, skin, and stems is used for AuNPs synthesis. UV-Vis, XPS, SEM, and ATR-FTIR spectroscopies demonstrate the main role of the extract’s polyphenolic components in stabilizing nanoparticles. XRD, DLS, and Zeta Potential analyses were used to characterize AuNPs. Moreover, the ionic strength, pH, and temperature role was investigated through the Surface Plasmon Resonance (SPR) band observation to assess AuNPs’ stability and photostability. For foreseeing the as-synthesized AuNPs’ potential use in cosmetic and biomedical fields as multifunctional platforms, their antioxidant, and skin-lightening properties were tested, together with their sunscreen ability. A preliminary in-vitro evaluation is reported about the AuNPs’ cytoprotective effects against H₂O₂ oxidative stress-induced in normal human dermal fibroblasts. Briefly, the possibility of reusing the grape pomace waste after the AuNPs synthesis as an adsorbent for the efficient removal of emergent contaminants is preliminarily discussed in the paper, further valorizing the use of waste according to a bio circular approach. Full article

FINEAU (2021–2024) is a trans-disciplinary research project involving French, Serbian, Italian, Portuguese and Romanian colleagues, a French agricultural cooperative and two surface-treatment industries, intending to propose chènevotte, a co-product of the hemp industry, as an adsorbent for the removal of pollutants from polycontaminated wastewater. The first objective of FINEAU was to prepare and characterize chènevotte-based materials. In this study, the impact of water washing and treatments (KOH, Na₂CO₃ and H₃PO₄) on the composition and structure of chènevotte (also called hemp shives) was evaluated using chemical analysis, X-ray diffraction (XRD) analysis, scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) spectroscopy, X-ray computed nanotomography (nano-CT), attenuated total reflectance–Fourier transform infrared (ATR-FTIR) spectroscopy, solid state NMR spectroscopy and thermogravimetric analysis. The results showed that all these techniques are complementary and useful to characterize the structure and morphology of the samples. Before any chemical treatment, the presence of impurities with a compact unfibrillated structure on the surfaces of chènevotte samples was found. Data indicated an increase in the crystallinity index and significant changes in the chemical composition of each sample after treatment as well as in surface morphology and roughness. The most significant changes were observed in alkaline-treated samples, especially those treated with KOH. Full article

The “modern” cosmetology industry is focusing on research devoted to discovering novel neurocosmetic functional ingredients that could improve the interactions between the skin and the nervous system. Many cosmetic companies have started to formulate neurocosmetic products that exhibit their activity on the cutaneous nervous system by affecting the skin’s neuromediators through different mechanisms of action. This review aims to clarify the definition of neurocosmetics, and to describe the features of some functional ingredients and products available on the market, with a look at the regulatory aspect. The attention is devoted to neurocosmetic ingredients for combating skin stress, explaining the stress pathways, which are also correlated with skin aging. “Neuro-relaxing” anti-aging ingredients derived from plant extracts and neurocosmetic strategies to combat inflammatory responses related to skin stress are presented. Afterwards, the molecular basis of sensitive skin and the suitable neurocosmetic ingredients to improve this problem are discussed. With the aim of presenting the major application of Botox-like ingredients as the first neurocosmetics on the market, skin aging is also introduced, and its theory is presented. To confirm the efficacy of the cosmetic products on the market, the concept of cosmetic claims is discussed. Full article

Extra virgin olive oil (EVOO) is well known for containing relevant amounts of healthy phenolic compounds. The European Food Safety Authority (EFSA) allowed a health claim for labelling olive oils containing a minimum amount of hydroxytyrosol (OHTyr) and its derivatives, including tyrosol (Tyr). Therefore, harmonized and standardized analytical protocols are required in support of an effective application of the health claim. Acid hydrolysis performed after extraction and before chromatographic analysis has been shown to be a feasible approach. Nevertheless, other fast, green, and easy methods could be useful for on-site screening and monitoring applications. In the present research, a natural deep eutectic solvent (NADES) composed of lactic acid and glucose was used to perform a liquid/liquid extraction on EVOO samples, followed by UV-spectrophotometric analysis. The spectral features of the extracts were related with the content of total OHTyr and Tyr, determined by the acid hydrolysis method. The second derivative of spectra allowed focusing on three single wavelengths (i.e., 299 nm, 290 nm, and 282 nm) significantly related with total OHTyr, total Tyr, and their sum, respectively. In particular, the sum of OHTyr and Tyr could be determined with a root mean square error of prediction of 29.5 mg kg⁻¹, while the limits of quantitation and detection were respectively 11.8 and 4.9 mg kg⁻¹. The proposed method, therefore, represents an easy screening tool, with the use of a green, food-derived solvent, and could be considered as an attempt to pave the way for food grade analytical chemistry. Full article

The photo-catalytic degradation of a textile azo-dye as Methyl Orange was studied in an innovative unit constituted by a channel over which a layer of titanium dioxide (TiO₂) catalyst in anatase form was deposited and activated by UVB irradiation. The degradation kinetics were followed after variation of the chemical, physical, and hydraulic/hydrodynamic parameters of the system. For this purpose, the influence of the TiO₂ dosage (g/cm³), dye concentration (mg/L), pH of the solution, flow-rate (L/s), hydraulic load (cm), and irradiation power (W) were evaluated on the degradation rates. It was observed that the maximum dosage of TiO₂ was 0.79 g/cm³ while for higher dosage a reduction of homogeneity of the cement conglomerate occurred. The Langmuir–Hinshelwood (LH) kinetic model was followed up to a dye concentration around 1 mg/L. It was observed that with the increase of the flow rate, an increase of the degradation kinetics was obtained, while the further increase of the flow-rate associated with the modification of the hydraulic load determined a decrease of the kinetic rates. The results also evidenced an increase of the kinetic rates with the increase of the UVB intensity. A final comparison with other dyes such as Methyl Red and Methylene Blue was carried out in consideration of the pH of the solution, which sensibly affected the removal efficiencies. Full article

Seafood, a delight for many people, is sold in the market as a wide variety of products. However, seafood industries produce many by-products; for example, during the processing, the heads and shells of shellfish are generated as waste. This results in the generation of a large amount of shell waste that is accumulated over time, inducing a major environmental concern. Effective solutions for recycling shell waste should be taken into consideration, and the extraction of commercially useful substances like chitin and its derivates, such as chitosan, could be a valid solution for reducing the seafood waste’s environmental impact. Thus, during this work, we propose the use of chitosan as biowaste, to induce the formation of solid films useful for decontaminating water from emerging pollutants. In particular, ketoprofen was used as a model contaminant, and a high percentage of removal, at least 90%, was obtained in a short time under our experimental conditions. Thus, a comprehensive investigation into the adsorption of ketoprofen onto chitosan film was performed, detailing the nature of the adsorption by studying the effects of pH, temperature changes, and electrolyte presence in the solutions containing the pollutant. The process was found to be pH-dependent, involving meanly electrostatic interactions between the pollutant molecules and chitosan. The endothermic character of the adsorption was inferred. The kinetics of the process was investigated, showing that the pseudo second-order kinetic model best fit the experimental data. A recycling process of the adsorbent was proposed; therefore, the adsorbed pollutant can be recovered by reusing the same adsorbent material for further consecutive cycles of adsorption without affecting the efficiency for ketoprofen removal from water. Full article

This paper reported the first example on the use of chitosan films, without further modification, to remove and recover, through bio-sorption processes, the emerging pollutant Diclofenac from water. The latter was adopted as a model, among non-steroidal anti-inflammatory drugs, by obtaining a maximum adsorption capacity, q_max, on chitosan of about 10 mg/g, under the applied experimental conditions of work. The literature gap about the use of chitosan films, which was already used for dyes and heavy metals removal, to adsorb emerging pollutants from water was covered, claiming the wide range application of chitosan films to remove a different class of pollutants. Several parameters affecting the Diclofenac adsorption process, such as the pH and ionic strength of solutions containing Diclofenac, the amount of the bio-sorbent and pollutant, and the temperature values, were investigated. The kinetics and the adsorption isotherms, along with the thermodynamic parameters (ΔG°, ΔH°, and ΔS°) were also evaluated. The process occurred very efficiently, and Chitosan/Diclofenac amounts dependent, remove about the 90% of the pollutant, in 2 h, from the tested solutions, through electrostatic interaction involving the carboxylic moiety of Diclofenac and Chitosan amino groups. This finding was confirmed by the pH and salt effects on the bio-sorption process, including swelling measurements of Chitosan films and by FTIR-ATR analysis. In detail, the maximum adsorption was observed at pH 5, when pollutant and Chitosan were negatively and positively charged, respectively. By reducing or increasing the pH around this value, a reduced affinity was observed. Accordingly, the presence of salts retarded the Diclofenac removal screening its charges, which hinders the interaction with Chitosan. The sorption was spontaneous (ΔG° < 0) and endothermic (ΔH° > 0) following the pseudo-second order kinetic model. The process was Diclofenac and Chitosan amount dependent. In addition, the Freundlich and Temkin isotherms well described the process, which showed the heterogeneous character of the process. Experiments of the complete desorption were also performed by using NaCl solutions 0.25 M (like sea water salt concentration) proposing the reuse of the pollutant and the recycling of the bio-sorbent lowering the associated costs. The versatility of the adsorbent was reported by exploring the possibility to induce the Diclofenac light-induced degradation after the adsorption and by-products adsorption onto chitosan films. To emphasize the chitosan capacity of treating water, the removal of another pollutant such as Ketoprofen and the mixture of Diclofenac and Ketoprofen were investigated. In this way, a green and eco-friendly production-pollution prevention technology for removing emerging pollutants from water was presented, which reduced the overall environmental impact. This illustrated experiments both in static and dynamic conditions for potential industrial applications. Full article

Hair is an important part of the body appeal and its look is a health indicator. Accordingly, recent advances in hair science and hair care technologies have been reported in literature claiming innovations and strategies for hair treatments and cosmetic products. The treatment of hair and scalp, primarily, involved the use of shampoo for an effective, but gentle cleansing; however, for years, the shampoo is considered not only as a cosmetic product having the purifying purpose, but it is also responsible for maintaining the health and the beauty of hair, imparting gloss and improving manageability. For meeting the needs of a multitasking formulation, following also the recent marketing-trend addressed to the "natural world", new challenges for cosmetic technology are aimed towards the research of natural ingredients, as well as new techniques for shampoo formulation. Regarding the recent development of solid shampoos, little information is available about their use, formulation and advantages. This review is largely focused on the description of solid shampoos, mainly based on the use of clays, herbs or flours as washing bases alternative to the traditional ones, consisting of a combination of synthetic surfactants, together with other usual ingredients expected in a shampoo formulation. Full article

β-cyclodextrin (β-CD) and hydroxypropyl-β-cyclodextrin (HP-β-CD) were used to prepare insoluble polymers using epichlorohydrin as a cross-linking agent and the azo dye Direct Red 83:1 was used as target adsorbate. The preliminary study related to adsorbent dosage, pH, agitation or dye concentration allowed us to select the best conditions to carry out the rest of experiments. The kinetics was evaluated by Elovich, pseudo first order, pseudo second order, and intra-particle diffusion models. The results indicated that the pseudo second order model presented the best fit to the experimental data, indicating that chemisorption is controlling the process. The results were also evaluated by Freundlich, Langmuir and Temkin isotherms. According to the determination coefficient (R²), Freunlich gave the best results, which indicates that the adsorption process is happening on heterogeneous surfaces. One interesting parameter obtained from Langmuir isotherm is q_max (maximum adsorption capacity). This value was six times higher when a β-CDs-EPI polymer was employed. The cross-linked polymers were fully characterized by nuclear magnetic resonance (NMR), Fourier transform infrared spectroscopy (FTIR), thermal gravimetric analysis (TGA). Also, morphology and particle size distribution were both assessed. Under optimized conditions, the β-CDs-EPI polymer seems to be a useful device for removing Direct Red 83:1 (close 90%), from aqueous solutions and industrial effluents. Complementarily, non-adsorbed dye was photolyzed by a pulsed light driven advanced oxidation process. The proposed methodology is environmental and economically advantageous, considering the point of view of a sustainable recycling economy in the textile dyeing process. Full article

A porous waste glass (RWPG = recycled waste porous glass) was used in wastewater treatments for the removal of lead ions from single, binary, and ternary metal solutions (with cadmium and nickel ions). Experiments were performed in columns (30 cm³, 10 g) filled with 0.5–1 mm beads till complete glass exhaustion (breakthrough). In the case of single and binary solutions, the columns were percolated at 0.2 Lh⁻¹ (2 mg Me⁺² L⁻¹); in the case of ternary solutions, the columns were percolated at 0.15–0.4 Lh⁻¹ (2 mg Me²⁺ L⁻¹) and with 2–5 mg Me²⁺ L⁻¹ influent concentration (0.2 Lh⁻¹). Lead ions were removed mainly by ion exchange and also by adsorption. From a kinetic point of view, the rate controlling step of the process was the interdiffusion of the lead ions in the Nernst stationary liquid film around the sorbent. The uptake of the metals and the glass selectivity were confirmed by Energy Dispersive X-ray spectroscopy (EDX) analysis. After lead retention process, glass beads were reused as lightweight aggregates for thermal insulating and environmental safe mortars. Full article