Search Results (302)

To enable multi-channel parallel spectral analysis in array-based devices such as micro-light-emitting diodes (Micro-LEDs) and line-scan spectral confocal systems, the development of compact array spectrometers has become increasingly important. In this work, a novel spectrometer architecture based on a microlens array grating (MLAG) is proposed, which addresses the major limitations of conventional spectrometers, including limited parallel detection capability, bulky structures, and insufficient spatial resolution. By integrating dispersion and focusing within a monolithic device, the system enables simultaneous acquisition across more than 2000 parallel channels within a 10 mm × 10 mm unit consisting of an f = 4 mm microlens and a 600 lines/mm blazed grating. Optimized microlens and aperture alignment allows for flexible control of the divergence angle of the incident light, and the system theoretically achieves nanometer-scale spectral resolution across a 380–780 nm wavelength range, with inter-channel measurement deviation below 1.25%. Experimental results demonstrate that this spectrometer system can theoretically support up to 2070 independently addressable subunits. At a wavelength of 638 nm, the coefficient of variation (CV) of spot spacing among array elements is as low as 1.11%, indicating high uniformity. The spectral repeatability precision is better than 1.0 nm, and after image enhancement, the standard deviation of the diffracted light shift is reduced to just 0.26 nm. The practical spectral resolution achieved is as fine as 3.0 nm. This platform supports wafer-level spectral screening of high-density Micro-LEDs, offering a practical hardware solution for high-precision industrial inline sorting, such as Micro-LED defect inspection. Full article

Forest structure parameters are critical for understanding and managing forest ecosystems, yet sparse forests have received limited attention in previous studies. To address this research gap, this study systematically evaluates and compares the sensitivity of active Synthetic Aperture Radar (SAR) and passive optical remote sensing to key forest structure parameters in sparse forests, including Diameter at Breast Height (DBH), Tree Height (H), Crown Width (CW), and Leaf Area Index (LAI). Using the novel computer-graphics-based radiosity model applicable to porous individual thin objects, named Radiosity Applicable to Porous Individual Objects (RAPID), we simulated 38 distinct sparse forest scenarios to generate both SAR backscatter coefficients and optical reflectance across various wavelengths, polarization modes, and incidence/observation angles. Sensitivity was assessed using the coefficient of variation (CV). The results reveal that C-band SAR in HH polarization mode demonstrates the highest sensitivity to DBH (CV = −6.73%), H (CV = −52.68%), and LAI (CV = −63.39%), while optical data in the red band show the strongest response to CW (CV = 18.83%) variations. The study further identifies optimal acquisition configurations, with SAR data achieving maximum sensitivity at smaller incidence angles and optical reflectance performing best at forward observation angles. This study addresses a critical gap by presenting the first systematic comparison of the sensitivity of multi-band SAR and VIS/NIR data to key forest structural parameters across sparsity gradients, thereby clarifying their applicability for monitoring young and middle-aged sparse forests with high carbon sequestration potential. Full article

The output energy of Laser Active Optical Systems (LAOSs), in which image brightness is amplified within the laser-active medium, is always higher than the input energy. This contrasts with conventional optical systems (OSs). As a result, a LAOS enables the creation of laser beams with tailored energy distribution across the aperture, making them ideal for material processing applications. This concept was first successfully implemented using metal vapor lasers as the gain medium. In these systems, material processing was achieved by using a laser beam that either carried the required energy profile or the image of the object itself. Later, other laser media were utilized for LAOSs, including barium vapor, strontium vapor, excimer XeCl lasers, and solid-state media. Additionally, during the development of these systems, several modifications were introduced. For example, Space-Time Light Modulators (STLMs) and CCD cameras were incorporated, along with the use of multipass amplifiers, disk-shaped or thin-disk (TD) solid-state laser amplifiers, and other advancements. These techniques have significantly expanded the range of power, energy, pulse durations, and operating wavelengths. Currently, TD laser amplifiers and STLMs based on Digital Light Processor (DLP) technology or Digital Micromirror Devices (DMDs) enhance the potential to develop LAOS devices for Subtractive and Additive Technologies (ST, AT), applicable in both macromachining (cutting, welding, drilling) and micro-nano processing. This review presents comparable characteristics and requirements for these various LAOS applications. Full article

Femtosecond laser micromachining was utilized to build up a micro-through-hole array into a sacrificial film, which was coated onto a copper specimen. This micro-through hole was shaped in the paraboloidal profile, with its micro-dimple on the interface between the copper substrate and the film. This profile was simply in correspondence with the laser energy profile. The array was used as a nucleation and growth site for nickel cluster deposition during wet plating. The micro-pillared unit cells nucleated at the micro-dimple and grew on the inside of the micro-through hole. After removing the sacrificial film, cleansing, and polishing, the nickel micro-pillar array was obtained, standing on the copper substrate. These unit cells and their alignments were measured through scanning electron microscopy and laser microscopy. Thermographic microscopy with FT-IR was utilized to measure the IR emittance as a function of wavelength. The focused areas were varied by controlling the aperture to analyze the effects of arrayed microtextures on the IR emittance. Full article

In this paper, we establish criteria for the design of small aperture antenna arrays for Direction of Arrival (DOA) estimation. We define a small aperture antenna array as one consisting of a few elements with an average interelement spacing less than or equal to half a wavelength. We use the spatial covariance matrix of the antenna array to derive the design criterion. It is well known that the DOA estimation performance of an antenna array is strongly related to the amount of information in this matrix. Also, the Cramer-Rao Bound of the estimated DOA is closely related to this matrix. We establish and demonstrate that, for optimal DOA estimation performance, a small aperture antenna array should have non-uniformly spaced and dissimilar antenna elements. Since mutual coupling between antenna elements makes their in situ responses dissimilar, instead of mitigating mutual coupling, one should include mutual coupling in the DOA estimation process to enhance the DOA estimation performance of antenna arrays. Full article

Conventional metalenses struggle with chromatic aberration and narrow field of view (FOV), making it challenging to meet the dispersion requirements for large apertures and compensate off-axis aberrations for wide FOV. Here, we demonstrate a hybrid metalens module consisting of five refractive plastic lenses and a polarization-insensitive metalens to achieve broadband achromatic imaging within 400–700 nm and a wide FOV up to 100°. The system exhibits negligible variation in focal length (~1.2%) across the visible range (460–656 nm) and consistently achieves modulation transfer function (MTF) values > 0.2 at 167 lp/mm across all wavelengths and incident angles. We also demonstrate integrated lens modules that capture high-quality images from distances ranging between 0.5 and 4 m without post-processing, showcasing its potential for compact, wide-angle optical systems. Full article

Holographic optical elements (HOEs) are promising for solar energy collection due to their advantages of lightweight and high efficiency, but the narrow reconstruction of their angular and spectral widths limits their application. This paper proposes a novel holographic lens array solar collector (HLASC), which can collect light from a large angle range with an expanded spectrum. The large acceptance angle is achieved by a holographic lens array with a large relative aperture. To expand the collection spectral width within a large incident angle, the collection spectrum is spatially allocated within a single lens range. The methods of single-wavelength recording and multi-wavelength reconstruction contribute to the flexible design and simple fabrication of the HLASC. The optical experiment demonstrates that the HLASC can collect the entire visible spectrum in a range greater than 54°. We believe that an expanded reconstruction angle and wavelength will promote the widespread application of HOEs in solar energy collection. Full article

The optimization of photoinjector brightness is crucial for achieving the highest performance at X-ray free-electron lasers. To this end, photocathode laser pulse shaping has been identified as a key technology for enhancing photon flux and lasing efficiency at short wavelengths. Supported by beam dynamics simulations, we identify transversely and longitudinally truncated Gaussian electron bunches as a beneficial bunch shape in terms of the projected emittance and 5D brightness. The realization of such pulses from chirped Gaussian pulses is studied for 514 nm and 257 nm wavelengths by inserting an amplitude mask in the symmetry plane of the pulse stretcher to achieve longitudinal shaping and an aperture for transverse beam shaping. Using this scheme, transversely and longitudinally truncated Gaussian pulses can be generated and later used for the production of up to 3 nC electron bunches in the photoinjector. The 3D pulse shape at a wavelength of 514 nm is characterized via imaging spectroscopy, and second-harmonic generation frequency-resolved optical gating (SHG FROG) measurements are also performed to analyze the shaping scheme’s efficacy. Furthermore, this pulse-shaping scheme is transferred to a UV stretcher, allowing for direct application of the shaped pulses to cesium telluride photocathodes. Full article

By extending synthetic aperture technology from a microwave band to laser wavelength, the synthetic aperture ladar (SAL) achieves extremely high spatial resolution independent of the target distance in long-range imaging. Nonlinear phase correction is a critical challenge in SAL imaging. To address the issue of phase noise during the imaging process, we first analyze the theoretical impact of nonlinear phase noise in imaging performance. Subsequently, a reconstruction and compensation method based on orthonormal complete basis functions is proposed to mitigate nonlinear phase noise in SAL imaging. The simulation results validate the accuracy and robustness of the proposed method, while experimental data demonstrate its effectiveness in improving system range resolution and reducing the peak side lobe ratio by 3 dB across various target scenarios. This advancement establishes a solid foundation for the application of SAL technology in ground-based remote sensing and space target observation. Full article

The purpose of this study was to evaluate the bactericidal effect of 270 nm UV-C light-emitting diode (LED) light delivered through a newly designed prototype device with thin optical fiber against Enterococcus faecalis (E. faecalis). The prototype device, developed to integrate UV-C light into a thin optic fiber (diameter 124 µm) connected to a UV-C LED (Luminous Device; Sunnyvale, CA, USA) via a specialized double-lens system that focuses divergent light to achieve a 65 mm working distance and a numerical aperture of 0.22. E. faecalis, was cultured at 37 °C under aerobic conditions for 24 h. The UV-C LED optical fiber was positioned 10 mm above the bacterial culture prepared in the wells of a 96-well plate. The E. faecalis cells were exposed to UV-C irradiation for 0, 10, 30, 60, 90, 120 and 180 s. Following irradiation, the OD600 values were measured after incubation at 37 °C for an additional 24 h. The data were statistically analyzed using one-way ANOVA, followed by Tukey’s honestly significant difference (HSD) test at a significance level of 0.05. UV irradiation at 270 nm significantly reduced E. faecalis growth in a time-dependent manner (p < 0.05). No significant changes were observed at 0 and 10 s, while peak reductions occurred at 120 and 180 s, with effects beginning at 30 s and increasing over time. The 270 nm UV-C wavelength was highly effective in bactericidal action against E. faecalis. The custom-designed UV-C delivery system effectively integrated the light source into a thin optical fiber, allowing for efficient UV-C light transmission and demonstrating its potential for application in narrow spaces such as root canals. Full article

One of the main challenges in Synthetic Aperture Radar (SAR) change detection involves using SAR images from different flight passes. Depending on the flight pass, objects have different specular reflections since the radar cross-sections of these objects can be totally different between passes. Then, it is common knowledge that the flight passes must be close to identical for conventional SAR change detection. Wavelength-resolution SAR refers to a SAR system with a spatial resolution approximately equal to the wavelength. This high relative resolution helps to stabilize the ground clutter in the SAR images. Consequently, the restricted requirement about identical flight passes for SAR change detection can be relaxed, and SAR change detection becomes possible with nonidentical passes. This paper shows that robust principal component analysis (RPCA) is efficient for change detection even using wavelength-resolution SAR images acquired with very different flight passes. It presents several SAR change detection experimental results using flight pass differences up to 95°. For slightly different passes, e.g., 5°, our method reached a false alarm rate (FAR) of approximately one false alarm per square kilometer for a probability of detection (PD) above 90%. In a particular setting, it achieves a PD of 97.5% for a FAR of 0.917 false alarms per square kilometer, even using SAR images acquired with nonidentical passes. Full article

Spaceborne synthetic aperture radar (SAR) has been proven capable of observing the directional ocean wave spectrum across the global ocean. Most of the efforts focus on the integrated wave parameters to characterize the imaged ocean wave properties. The newly proposed spectrum-based radar parameter mean cross-spectrum (MACS) is investigated using SAR image spectral properties of range-traveling waves at a wavelength of 20 m, based on Sentinel-1 wave mode acquisition of high spatial resolution (5 m). The magnitude of MACS is documented relative to environmental conditions (wind speed and direction) in terms of its variation for two polarizations at two incidence angles. This parameter exhibits distinct upwind–downwind asymmetry and polarization ratio at two incidence angles (23.8° and 36.8°). In addition, by comparing the SAR measurements with simulated MACS, we derive an improved real aperture radar modulation transfer function. Results obtained in this study shall help obtain a more accurate ocean wave spectrum based on the improved RAR modulations. Full article

In this study, novel focusing performances of high-numerical-aperture (NA) micro-Fresnel zone plates (FZPs) with selective occlusion are identified and investigated through numerical calculations based on vectorial angular spectrum (VAS) theory, and further rigorously validated using the finite-difference time-domain (FDTD) method. The central occlusion of a standard micro-FZP can significantly extend the depth of focus while keeping the lateral size of the focusing spot essentially unchanged. When a standard micro-FZP only retains two separated transparent rings and all other rings are obstructed, it will result in multi-focus phenomena; at the same time, the number of focal points is equal to the difference in number between the two separated transparent rings. Furthermore, a focusing light needle can be generated by combining the central occlusion and wavelength shift of a standard micro-FZP. This study not only provides new ideas for the design and optimization of micro-FZPs but also provides reference for the expansion of practical applications of FZPs. Full article

Researchers frequently utilize the method of optical initial structure (MOIS) of Czerny–Turner (C–T) spectrometers for aberration-correction studies based on the coma-free equation. While effective, this method has limitations: small numerical apertures at slits (0.05–0.07) hinder weak signal detection; V or W-shaped variations in Airy disk across wavelengths; optical resolution depends on the radius of the collimating lens may not match detector resolution; and sequence patterns based on the spot diagrams cannot simulate the full width at half maximum (FWHM) under discrete sampling. To address these issues, using ray tracing and imaging equations, three criteria are proposed: luminous flux and aberration balance (LFAB), Airy disk variation at imaging points (ADVI), and optical-detector resolution matching (ORDR). A verification system with a 500–750 nm wavelength range and 0.4 nm resolution was designed. Results show that designing spectrometers based on these criteria increases the slit’s numerical aperture to 0.11 while controlling aberrations. After optimization, the tangential Airy disk size decreased by 28% with variations within 3 μm. Discrete sampling indicates FWHM pixel errors remain within 1/2 pixel of the theoretical value, and FWHM is at least 2.5 pixels, satisfying stricter sampling requirements beyond Nyquist. Optimization only involves adjusting the image plane by 0.017 mm axially, 0.879 mm off-axis, and 0.48° eccentricity. This research strengthens spectrometer design theory and improves practical applications. Full article

Bismuth telluride (Bi₂Te₃) has attracted significant attention due to its broadband ultrafast optical response and strong nonlinearity at high laser fluence in the field of optoelectronic materials. The objective of this work is to study the effect of Al doping on the structure, linear optical properties, and nonlinear optical absorption behavior of Bi₂Te₃ thin films. The amorphous Al-doped Bi₂Te₃ thin films with varying Al doping concentrations were prepared using magnetron co-sputtering. The structure and linear optical properties were characterized using X-ray diffraction, scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy, spectroscopic ellipsometry, and UV/Vis/NIR spectrophotometry. The third-order nonlinear optical absorption properties of Al: Bi₂Te₃ thin films were investigated using the open-aperture Z-scan system with a 100 fs laser pulse width at a wavelength of 800 nm and a repetition rate of 1 kHz. The results indicate that Al dopant reduces both the refractive index and extinction coefficient and induces a redshift in the optical bandgap. The optical properties of the films can be effectively modulated by varying the Al doping concentration. Compared with undoped Bi₂Te₃ thin films, Al-doped Bi₂Te₃ thin films exhibit larger nonlinear optical absorption coefficients and higher damage thresholds and maintaining high transmittance. These findings provide experimental evidence and a reliable approach for the further optimization and design of ultrafast nonlinear optical devices. Full article