Search Results (16)

Water flooding is one of the most widely used secondary oil recovery methods for enhanced oil recovery (EOR). However, as a reservoir matures, excessive water production often accompanies oil production. To address this issue, the injection–production coupling technique (IPCT) has been proposed to control water production and improve oil recovery. Despite its practical application, the underlying mechanisms governing the injection–production process remain unclear. To investigate this, a transparent heterogeneous sand pack model and a visualization micro-model were employed to examine the impact of the injection–production mode on oil recovery and to uncover the mechanisms of enhanced oil recovery. The results indicate that, compared to the conventional continuous injection–production mode, both the fluid flow swept area and incremental oil recovery are significantly higher in the IPCT. Sweep efficiency improves by adjusting the injection–production streamlines and displacement directions. Notably, the oil displacement effect in the “stop injection” mode is more effective than in the “reduce injection” mode. These findings suggest that the coupling injection–production mode can efficiently recover residual oil in low permeability zones, thereby enhancing overall oil recovery. Full article

With increasing energy demands and depleting oil accessibility in reservoirs, the investigation of more effective enhanced oil recovery (EOR) methods for deep and tight reservoirs is imminent. This study investigates a novel hybrid EOR method, a synergistic approach of nonionic surfactant flooding with intermediate CO₂-based oil swelling. This study is focused on the efficiency of surfactant flooding and low-pressure oil swelling in oil recovery. We conducted a fluorescence-based microscopic analysis in a microchannel to explore the effect of sodium dodecyl sulfate (SDS) surfactant on CO₂ diffusion in Texas crude oil. Based on the change in emission intensity of oil, the results revealed that SDS enhanced CO₂ diffusion at low pressure in oil, primarily due to SDS aggregation and reduced interfacial tension at the CO₂ gas–oil interface. To validate the feasibility of our proposed EOR method, we adopted a ‘reservoir-on-a-chip’ approach, incorporating flooding tests in a polymethylmethacrylate (PMMA)-based micromodel. We estimated the cumulative oil recovery by comparing the results of two-stage surfactant flooding with intermediate CO₂ swelling at different pressures. This novel hybrid approach test consisted of a three-stage sequence: an initial flooding stage, followed by intermediate CO₂ swelling, and a second flooding stage. The results revealed an increase in cumulative oil recovery by nearly 10% upon a 2% (w/v) solution of SDS and water flooding compared to just water flooding. The results showed the visual phenomenon of oil imbibition during the surfactant flooding process. This innovative approach holds immense potential for future EOR processes, characterized by its unique combination of surfactant flooding and CO₂ swelling, yielding higher oil recovery. Full article

Our target USH reservoir in the D oilfield is characterized by “inverse rhythm” deposition with the noticeable features of “high porosity and low permeability”. The reservoir has been developed with waterflooding using horizontal wells. Due to the strong heterogeneity of the reservoir, water channeling is severe, and the water cut has reached 79%. Considering the high temperature and high salinity reservoir conditions, polymer microspheres (PMs) were selected to realize conformance control. In this study, characterization of the polymer microsphere suspension was achieved via morphology, size distribution, and viscosity measurement. Furthermore, a multi-scale visualization study of the reservoir development process, including waterflooding, polymer microsphere flooding, and subsequent waterflooding, was conducted using macro-scale coreflooding and calcite-etched micromodels. It was revealed that the polymer microspheres could swell in the high salinity brine (170,000 ppm) by 2.7 times if aged for 7 days, accompanied by a viscosity increase. This feature is beneficial for the injection at the wellbore while swelled to work as a profile control agent in the deep formation. The macro-scale coreflood with a 30 cm × 30 cm × 4.5 cm layer model with 108 electrodes installed enabled the oil distribution visualization from different perpendicular cross sections. In this way, the in situ conformance control ability of the polymer microsphere was revealed both qualitatively and quantitatively. Furthermore, building on the calcite-etched visible micro-model, the pore-scale variation of the residual oil when subjected to waterflooding, polymer microsphere waterflooding, and subsequent waterflooding was collected, which revealed the oil displacement efficiency increase by polymer microspheres directly. The pilot test in the field also proves the feasibility of conformance control by the polymer microspheres, i.e., more than 40,000 bbls of oil increase was observed in the produces, accompanied by an obvious water reduction. Full article

Plants rely on potassium for many critical biological processes, but most soils are potassium limited. Moving potassium from the inaccessible, mineral-bound pool to a more bioavailable form is crucial for sustainably increasing local potassium concentrations for plant growth and health. Here, we use a synthetic soil habitat (mineral doped micromodels) to study and directly visualize how the saprotrophic fungus, Fusarium sp. DS 682, weathers K-rich soil minerals. After 30 days of fungal growth, both montmorillonite and illite (secondary clays) had formed as surface coatings on primary K-feldspar, biotite, and kaolinite grains. The distribution of montmorillonite differed depending on the proximity to a carbon source, where montmorillonite was found to be associated with K-feldspar closer to the carbon (C) source, which the fungus was inoculated on, but associated with biotite at greater distances from the C source. The distribution of secondary clays is likely due to a change in the type of fungal exuded organic acids; from citric to tartaric acid dominated production with increasing distance from the C source. Thus, the main control on the ability of Fusarium sp. DS 682 to weather K-feldspar is proximity to a C source to produce citric acid via the TCA cycle. Full article

Underground porous media are complex multiphase systems, where the behavior at the macro-scale is affected by physical phenomena occurring at the pore(micro)-scale. The understanding of pore-scale fluid flow, transport properties, and chemical reactions is fundamental to reducing the uncertainties associated with the dynamic behavior, volume capacity, and injection/withdrawal efficiency of reservoirs and groundwater systems. Lately, laboratory technologies were found to be growing along with new computational tools, for the analysis and characterization of porous media. In this context, a significant contribution is given by microfluidics, which provides synthetic tools, often referred to as micromodels or microfluidic devices, able to mimic porous media networks and offer direct visualization of fluid dynamics. This work aimed to provide a review of the design, materials, and fabrication techniques of 2D micromodels applied to the investigation of multiphase flow in underground porous media. The first part of the article describes the main aspects related to the geometrical characterization of the porous media that lead to the design of micromodels. Materials and fabrication processes to manufacture microfluidic devices are then described, and relevant applications in the field are presented. In conclusion, the strengths and limitations of this approach are discussed, and future perspectives are suggested. Full article

Polymer flooding is a key technology for improving reservoir heterogeneity around the world, and it has made great progress. However, the traditional polymer has many shortcomings in the theory and application, which causes the efficiency of polymer flooding to gradually decrease and secondary reservoir damage after a long period of polymer flooding. In this work, a novel polymer particle (soft dispersed microgel, SMG) is used as the research object to further investigate the displacement mechanism and reservoir compatibility of SMG. The visualization experiments of the micro-model prove that SMG has excellent flexibility and can be highly deformable to realize deep migration through the pore throat smaller than SMG itself. The visualization displacement experiments of the plane model further show that SMG has a plugging effect, which makes the displacing fluid flow into the middle and low permeability layers, improving the recovery of these layers. The compatibility tests show that the optimal permeability of the reservoir for SMG-μm is 250–2000 mD, and the corresponding matching coefficient range is 0.65–1.40. For SMG-mm⁻, its corresponding optimal permeabilities of reservoir and matching coefficient are 500–2500 mD and 1.17–2.07, respectively. The comprehensive analysis demonstrates that the SMG has excellent ability of the water-flooding swept control and compatibility with reservoirs, having the potential to solve the problem of traditional polymer flooding. Full article

The understanding of multiphase flow phenomena occurring in porous media at the pore scale is fundamental in a significant number of fields, from life science to geo and environmental engineering. However, because of the optical opacity and the geometrical complexity of natural porous media, detailed visual characterization is not possible or is limited and requires powerful and expensive imaging techniques. As a consequence, the understanding of micro-scale behavior is based on the interpretation of macro-scale parameters and indirect measurements. Microfluidic devices are transparent and synthetic tools that reproduce the porous network on a 2D plane, enabling the direct visualization of the fluid dynamics. Moreover, microfluidic patterns (also called micromodels) can be specifically designed according to research interests by tuning their geometrical features and surface properties. In this work we design, fabricate and test two different micromodels for the visualization and analysis of the gas-brine fluid flow, occurring during gas injection and withdrawal in underground storage systems. In particular, we compare two different designs: a regular grid and a real rock-like pattern reconstructed from a thin section of a sample of Hostun rock. We characterize the two media in terms of porosity, tortuosity and pore size distribution using the A* algorithm and CFD simulation. We fabricate PDMS-glass devices via soft lithography, and we perform preliminary air-water displacement tests at different capillary numbers to observe the impact of the design on the fluid dynamics. This preliminary work serves as a validation of design and fabrication procedures and opens the way to further investigations. Full article

Residual crude oil production from low-permeability reservoirs has become a huge challenge because conventional recovery techniques are inefficient. Nanofluids as a new type of oil-displacement agent have become a hot topic in recent years to enhance oil recovery (EOR) in reservoirs. However, the imperfection of agglomeration, dissolution, and instability of nanofluids in reservoir environments limit their ability to drive oil. Here, a novel “microbial-nanofluid” composed of petroleum hydrocarbon-degrading bacteria (PHDB, namely Bacillus cereus) and SiO₂ nanoparticles was proposed as a potential new technology for enhancing residual oil recovery. The micromodel displacement test results showed that the optimum composite concentration of “microbial-nanofluids” were PHDB (7.0%, v/v) and SiO₂ nanoparticles (100 mg/L), and the residual oil recovery was increased by 30.1% compared with waterflooding (68.8%). Moreover, the morphological characteristics of residual oil mobilization after “microbial-nanofluid” flooding were mainly small and dispersed oil droplets in the excessive areas, and the dead-end areas were almost clean with mobilization. Furthermore, the cooperation mechanism of four kinds of “microbial-nanofluids” to enhance the residual oil recovery in low-permeability reservoirs was preliminarily clarified, namely the co-emulsification of oil, working together to unclog oil clog, microbial-nanofluid self-assembly, and structural disjoining pressure. This study demonstrated that PHDB-SiO₂ nanoparticle composite flooding technology provided a significant potential for the EOR from low-permeability reservoirs. Full article

The recovery of oil from a reservoir can be accomplished with various methods, one of the most commonly applied types being waterflooding. A common theory used to describe immiscible displacement is the Buckley–Leverett theory. A brand new type of micromodel, generated and fabricated by using a micro-computer tomography ($\mu$CT) image stack of a real sandstone core, was used to conduct immiscible displacement experiments. Critical logging data were recorded, and a high-resolution camera took pictures of the displacement process. In an image processing tool (MATLAB), an algorithm was developed to evaluate the pictures of the experiment and to examine the changes in the saturations of the displacing and the displaced fluid. The main objective of the displacement experiment was to validate the new microchip in two-phase displacement experiments and to assess the feasibility of the image processing algorithm. This was performed by comparing the results of the experimental to the analytical solutions, which were derived from the Buckley–Leverett theory. The comparison of the results showed a good match between the two types of solutions. The applicability of the analytical results to the experimental procedures was observed. Additionally, the usage of the newly fabricated micromodel and its potential to visualize the fluid flow behavior in porous media were assessed. Full article

The alkali/surfactant/polymer (ASP) flood has long been considered to reduce residual oil saturation significantly after waterflood. This paper provides an experimental investigation of the factors (permeability, pore structure, ASP formula, injection volume, viscosity, and injection volume) that influence the evolution of residual oil after ASP flooding. ASP flood experiments were conducted on the cores drilled in Daqing field, and two-dimensional real-structure micromodels were constructed based on these cores. For the ASP core flood experiments, X-ray computed tomography imaging was used for the visualization of the residual oil evolution. For the ASP micromodel flood experiments, images of the residual oil distribution were obtained using a microscope with a 5× magnification objective. The results showed that as water saturation increased during the flood, the proportion of oil clusters decreased, and the proportion of oil droplets first increased and then decreased. For the cores with smaller pore throats and more complex pore structure, the residual oil became more scattered. In this case, the oil clusters became smaller, and oil droplets became easier to retain. An increased injection rate improved the emulsification, resulting in more residual oil in small pores getting replaced. Increasing the viscosity by increasing the polymer concentration improved the sweep efficiency, mainly because residual oil in large pore throats was displaced, but had a negative impact on emulsification. Increasing the viscosity of the injection fluid was shown to have a negative impact on improving the oil recovery ratio, because the mobilization of residual oil in smaller pores was greatly impacted by emulsification. The effect of increasing injection volume on improving recovery was more pronounced for cores with lower permeability. Full article

Investigations into the structures of gas hydrates, the mechanisms of formation, and dissociation with modern instruments on the experimental aspects, including Raman, X-ray, XRD, X-CT, MRI, and pore networks, and numerical analyses, including CFD, LBM, and MD, were carried out. The gas hydrate characteristics for dissociation and formation are multi-phase and multi-component complexes. Therefore, it was important to carry out a comprehensive investigation to improve the concept of mechanisms involved in microscale porous media, emphasizing micro-modeling experiments, 3D imaging, and pore network modeling. This article reviewed the studies, carried out to date, regarding conditions surrounding hydrate dissociation, hydrate formation, and hydrate recovery, especially at the pore-scale phase in numerical simulations. The purpose of visualizing pores in microscale sediments is to obtain a robust analysis to apply the gas hydrate exploitation technique. The observed parameters, including temperature, pressure, concentration, porosity, saturation rate, and permeability, etc., present an interrelationship, to achieve an accurate production process method and recovery of gas hydrates. Full article

CO₂ convective mixing in water has been visualized in Hele-Shaw and PVT cell experiments but not at the pore scale. Furthermore, CO₂ convective mixing in a three-phase system (i.e., CO₂ in the presence of both water and oil) has not been visually investigated. A vertically placed micromodel setup was used to visualize CO₂ convective mixing at 100 bar and 50 °C, representative of reservoir conditions. To the best of our knowledge, for the first time, we have visually investigated CO₂ convective mixing in water at the pore scale and also CO₂ convective mixing in a multiphase system (water and oil). CO₂ mixing in water governed by both diffusion and convection mechanisms was observed. The vertical CO₂ transport velocity was calculated to be 0.3 mm/min in both a 100% water saturation system and a residual oil-saturated system. First, CO₂ always found the easiest path through the connected pores, and then CO₂ was transported into less connected pores and dead-end pores. CO₂ transport into dead-end pores was slower than through the preferential path. CO₂ transport into water-filled ganglia with trapped oil was observed and was slower than in water. Full article

Understanding transport phenomena and governing mechanisms of different physical and chemical processes in porous media has been a critical research area for decades. Correlating fluid flow behaviour at the micro-scale with macro-scale parameters, such as relative permeability and capillary pressure, is key to understanding the processes governing subsurface systems, and this in turn allows us to improve the accuracy of modelling and simulations of transport phenomena at a large scale. Over the last two decades, there have been significant developments in our understanding of pore-scale processes and modelling of complex underground systems. Microfluidic devices (micromodels) and imaging techniques, as facilitators to link experimental observations to simulation, have greatly contributed to these achievements. Although several reviews exist covering separately advances in one of these two areas, we present here a detailed review integrating recent advances and applications in both micromodels and imaging techniques. This includes a comprehensive analysis of critical aspects of fabrication techniques of micromodels, and the most recent advances such as embedding fibre optic sensors in micromodels for research applications. To complete the analysis of visualization techniques, we have thoroughly reviewed the most applicable imaging techniques in the area of geoscience and geo-energy. Moreover, the integration of microfluidic devices and imaging techniques was highlighted as appropriate. In this review, we focus particularly on four prominent yet very wide application areas, namely “fluid flow in porous media”, “flow in heterogeneous rocks and fractures”, “reactive transport, solute and colloid transport”, and finally “porous media characterization”. In summary, this review provides an in-depth analysis of micromodels and imaging techniques that can help to guide future research in the in-situ visualization of fluid flow in porous media. Full article

This work describes the flow behavior of the oil recovery obtained by the injection of sulfate-modified/low-salinity water in micromodels with different wettabilities. It provides a detailed microscopic visualization of the displacement taking place during modified water flooding at a pore-scale level, while evaluating the effect of wettability on oil recovery. A comprehensive workflow for the evaluation is proposed that includes fluid–fluid and rock–fluid interactions. The methods studied comprise flooding experiments with micromodels. Artificial and real structure water-wet micromodels are used to understand flow behavior and oil recovery. Subsequently, water-wet, complex-wet, and oil-wet micromodels help understand wettability and rock–fluid interaction. The effect of the sulfate content present in the brine is a key variable in this work. The results of micromodel experiments conducted in this work indicate that sulfate-modified water flooding performs better in mixed-wet/oil-wet (artificial structure) than in water-wet systems. This slightly differs from observations of core flood experiments, where oil-wet conditions provided better process efficiency. As an overall result, sulfate-modified water flooding recovered more oil than SSW injection in oil-wet and complex-wet systems compared to water-wet systems. Full article

It is difficult to investigate the formation process and occurrence states of water in multi-type reservoirs, due to the strong heterogeneity and complex microstructure of the fracture–cavity carbonate gas reservoirs. To date, there is no systematic study on the occurrence characteristics of multi-type formation water, especially through visual observation experiments. In this paper, a new creation method for visual micromodels based on CT scan images and microelectronic photolithography techniques was described. Subsequently, a gas–drive–water visual experiment was conducted to intuitively study the formation mechanism and the occurrence states of formation water. Then, the ImageJ gray analysis method was utilized to quantitatively investigate the gas-water saturation and the proportion of residual water film. Finally, the occurrence characteristics of formation water and its effects on gas seepage flow were comprehensively analyzed. Visual experimental results showed that: the migration processes of natural gas in different types of reservoirs are different; the water in multiple media consists of native movable water and residual water, and residual water is composed of secondary movable water and irreducible water; the residual water mainly occurs in different locations of different reservoirs with the forms of “water film”, “water mass”, “water column” and “water droplets”; the main influencing factors are capillary force, surface tension, displacement pressure and channel connectivity. Quantitative results reflect that the saturation of movable water and residual water are the parameters related directly to reservoir physical properties, pore structure and displacement pressure—the smaller the size of flow channel, the larger the space occupied by water film; the thickness proportion of water film is increasing exponentially with the channel size; the thickness proportion of water film decreases as the increase of displacement pressure; the thickness proportion of water film is essentially constant when the displacement pressure increases to a certain extent. The conducted visual investigation not only improves our intuitive understanding of the occurrence characteristics of formation water, but also provides a theoretical basis for the efficient development of fracture-cavity gas reservoirs. Full article