Search Results (123)

The growing demand for sustainable construction practices has driven research into self-sensing materials incorporating recycled waste for smart SHM (Structural Health Monitoring) systems. However, previous works did not investigate the influence of rheological behavior and piezoresistive properties of sustainable cementitious sensors containing red mud (RM) on the strain monitoring of concrete beams. To address this gap, this study presents an experimental analysis of the rheological, mechanical, and self-sensing performance of mortars incorporating carbon black nanoparticles (CBN) and varying levels of RM (25–100% sand replacement by volume), followed by their application in monitoring strain in a reinforced concrete beam under dynamic loading. The results showed that increasing RM content led to higher viscosity and yield stress, with a 60% reduction in consistency index. Compressive strength increased by up to 80%, while mortars with RM content higher than 50% showed high electrical conductivity and reversible resistivity changes under load cycles. Mortars containing 50–100% RM demonstrated improved piezoresistive response, with a 23% increase in gauge factor, and the best-performing sensor embedded in a concrete beam exhibited stable and reversible fractional changes in resistivity, closely matching strain gauge data during dynamic loading conditions. These findings highlight the potential of RM-based smart mortars to enhance sustainability and performance in SHM applications. Full article

A multimode magneto-optical fiber based on Tb³⁺-containing borogermanate glass was designed, fabricated, and characterized, aiming at potential sensing applications. There are continuing challenges in the development of single-mode (SMF) or multimode (MMF) optical fibers doped with rare-earth (RE) ions and exhibiting high Verdet constants, related to devitrification of the precursor glass. Most RE-doped glass compositions are not suitable as precursors for core-cladding fiber production due to devitrification processes and consequent poor optical quality. Application as Faraday rotators is limited by the intrinsically low Verdet constant of silica (~0.589 rad T⁻¹ m⁻¹ at 1550 nm and 0.876 rad T⁻¹ m⁻¹ at 1310 nm). Borogermanate glasses are good candidates for manufacturing optical fibers due to their excellent potential to solubilize high concentrations of Tb³⁺ ions as well as satisfactory thermal stability. In this work, a magneto-optical core-cladding borogermanate fiber with a 227 μm diameter was fabricated, with characterization using differential scanning calorimetry (DSC), thermomechanical analysis (TMA), viscosity measurements, M-lines spectroscopy, UV-Vis-NIR absorption spectroscopy, the cut-back technique, and magneto-optical measurements. The measured numerical aperture (NA) was 0.183, with minimum attenuation of 13 dB m⁻¹ at 1270 nm. The Verdet constant (V_B) reached −6.74 rad T⁻¹ m⁻¹ at 1330 nm. Full article

This study explores the challenge of using anthocyanin-rich natural deep eutectic solvent (NADES) extracts to produce electrospun nanofibers for biodegradable freshness indicators. Red cabbage was extracted with two choline chloride-based NADESs (with citric or lactic acid), modified with 10–50% ethanol to lower viscosity, and compared with a standard 50% ethanol-water solvent. The citric acid NADES with 30% ethanol gave the highest anthocyanin yield (approx. 0.312 mg/mL, more than 20 times higher than the ethanol extract at approx. 0.014 mg/mL). For fiber fabrication, a polymer carrier blend of poly(ethylene oxide) (PEO) and sodium alginate (Alg) was employed, known to form hydrogen-bonded networks that promote chain entanglement and facilitate electrospinning. Despite this, the NADES extracts could not be electrospun into nanofibers, while the ethanol extract produced continuous, smooth fibers with diameters of approximately 100 nm. This highlights a clear trade-off; NADESs improve anthocyanin recovery, but their high viscosity and low volatility prevent fiber formation under standard electrospinning conditions. To leverage the benefits of NADES extracts, future work could focus on hybrid systems, such as multilayer films, core-shell fibers, or microcapsules, where the extracts are stabilized without relying solely on direct electrospinning. In storage tests, ethanol-extract nanofibers acted as effective pH-responsive indicators, showing visible color change from day 4 of meat storage. At the same time, alginate films with NADES extract remained unchanged after 12 days. These results highlight the importance of striking a balance between chemical stability and sensing sensitivity when designing anthocyanin-based smart packaging. Full article

Streptococcus thermophilus is a Gram-positive, homofermentative lactic acid bacterium classified within the Firmicutes phylum, recognized for its probiotic properties and significant role in promoting human health. This review consolidates existing understanding of its metabolic pathways, functional metabolites, and diverse applications, highlighting evidence-based insights to enhance scientific integrity. S. thermophilus predominantly ferments lactose through the Embden-Meyerhof-Parnas pathway, resulting in L(+)-lactic acid as the primary end-product, along with secondary metabolites including acetic acid, formic acid, and pyruvate derivatives. Exopolysaccharides (EPS) are composed of repeating units of glucose, galactose, rhamnose, and N-acetylgalactosamine. They display strain-specific molecular weights ranging from 10 to 2000 kDa and contribute to the viscosity of fermented products, while also providing antioxidant and immunomodulatory benefits. Aromatic compounds such as acetaldehyde and phenylacetic acid are products of amino acid catabolism and carbohydrate metabolism, playing a significant role in the sensory characteristics observed in dairy fermentations. Bacteriocins, such as thermophilins (e.g., Thermophilin 13, 110), exhibit extensive antimicrobial efficacy against pathogens including Listeria monocytogenes and Bacillus cereus. Their activity is modulated by quorum-sensing mechanisms that involve the blp gene cluster, and they possess significant stability under heat and pH variations, making them suitable for biopreservation applications. In food applications, S. thermophilus functions as a Generally Recognized as Safe (GRAS) starter culture in the production of yogurt and cheese, working in conjunction with Lactobacillus delbrueckii subsp. bulgaricus to enhance acidification and improve texture. Specific strains have been identified to mitigate lactose intolerance, antibiotic-related diarrhea, and inflammatory bowel diseases through the modulation of gut microbiota, the production of short-chain fatty acids, and the inhibition of Helicobacter pylori. The genome, characterized by a G + C content of approximately 37 mol%, facilitates advancements in Clustered Regularly Interspaced Short Palindromic Repeats (CRISPR)-Cas technology and heterologous protein expression, with applications extending to non-dairy fermentations and the development of postbiotics. This review emphasizes the adaptability of S. thermophilus, showcasing the variability among strains and the necessity for thorough preclinical and clinical validation to fully utilize its potential in health, sustainable agriculture, and innovation. It also addresses challenges such as susceptibility to bacteriophages and limitations in proteolytic activity. Full article

Suspended microchannel resonators (SMRs) are powerful tools for mass, density, and viscosity sensing. Among various transduction methods, full piezoelectric transduction offers key advantages, including on-chip integration, low energy dissipation, and linear response. This work explores sub-200 nm Al_0.6Sc_0.4N thin films for SMR transduction, benchmarking them against their well-established AlN predecessor. By integrating the piezoelectric stack into low-stress silicon nitride (ls-SiN_x) beam resonators, we investigate the impact of bottom electrode design, photoresist removal prior to deposition, and deposition bias on film quality. Characterization includes X-ray diffraction (XRD), scanning electron microscopy (SEM), d₃₁ piezoelectric coefficient, relative dielectric permittivity, and breakdown field measurements. Results illustrate the impacts of the studied parameters and demonstrate a fourfold increase in d₃₁, compared to AlN, confirming the strong potential of Al_0.6Sc_0.4N for high-performance SMR transduction. Full article

Trichlorfon, an organophosphorus pesticide widely used in agriculture and other fields, poses a severe risk to both food safety and human health. We developed a photonic crystal film sensing platform for detecting trichlorfon, a hazardous organophosphorus pesticide. The method exploits trichlorfon’s inhibition of acetylcholinesterase (AChE). Normally, AChE catalyzes acetylcholine hydrolysis to produce acetic acid, which decomposes CaCO₃ to release Ca²⁺. This triggers calcium alginate hydrogel formation, increasing solution viscosity and trapping water. When trichlorfon inhibits AChE, hydrogel formation fails, leaving the solution in a low-viscosity sol state with abundant free water. Immersing the film in trichlorfon-containing sodium alginate solutions causes water absorption and film swelling due to free water. Higher trichlorfon concentrations reduce hydrogel formation, increase free water, and amplify film swelling, resulting in proportionally higher reflectivity. The platform demonstrates a wide linear range (1–250 ng/mL) and a low detection limit (0.4 ng/mL) for trichlorfon. Successful analysis of real samples confirms its practicality for residue detection. This label-free thin-film sensor shows significant potential for monitoring trichlorfon and other organophosphorus pesticides. Full article

Resin Transfer Molding (RTM) is a widely used composite manufacturing process where liquid resin is injected into a closed mold filled with a fibrous preform. By applying this process, large pieces with complex shapes can be produced on an industrial scale, presenting excellent properties and quality. A true physical phenomenon occurring in the RTM process, especially when using vegetable fibers, is related to the absorption of resin by the fiber during the infiltration process. The real effect is related to the slowdown in the advance of the fluid flow front, increasing the mold filling time. This phenomenon is little explored in the literature, especially for non-isothermal conditions. In this sense, this paper does a numerical study of the liquid injection process in a closed and heated mold. The proposed mathematical modeling considers the radial, three-dimensional, and transient flow, variable injection pressure, and fluid viscosity, including the effect of liquid fluid absorption by the reinforcement (fiber). Simulations were carried out using Computational Fluid Dynamic tools. The numerical results of the filling time were compared with experimental results, and a good approximation was obtained. Further, the pressure, temperature, velocity, and volumetric fraction fields, as well as the transient history of the fluid front position and injection fluid volumetric flow rate, are presented and analyzed. Full article

Surface-enhanced Raman scattering (SERS) spectroscopy is an ultra-sensitive analytical method with the powerful signal-molecule detection capability. Coupling with the polydimethylsiloxane (PDMS) material, SERS can be enabled on a polymeric substrate for fast-developing bio-compatible sensing applications. However, due to PDMS’s high viscosity, conventional PDMS-SERS substrates are typically thick and stiff, limiting their freedom for engineering flexible micro/nano functioning devices. To address this issue, we propose to adopt a low viscosity decamethylcyclopentasiloxane (D5) solvent as a diluent solution. Via controlling the mixture ratio of D5 and PDMS and the spin-coating speed for deposition, this method resulted in a film of a well-defined thickness from sub-millimeter down to a 100 nm scale. Furthermore, thanks to the unsaturated Si-H chemical bonds in the PDMS curing agent, the PDMS film could effectively reduce the $A{g}^{+}$ ions to Ag nanoparticles (NPs) directly bonding onto the substrate surface uniformly. Via adjusting the size and density of the AgNPs through reaction temperature and time, strong SERS was achieved and verified using R6G with the detection limit down to 0.1 ppm, attributed to the AgNPs’ plasmonic enhancement effect. Full article

Blood coagulation tests are crucial in the clinical management of cardiovascular diseases and preoperative diagnostics. However, the widespread adoption of existing detection devices, such as thromboelastography (TEG) instruments, is hindered by their bulky size, prohibitive cost, and lengthy detection times. In contrast, magnetoelastic sensors, known for their low cost and rapid response, have garnered attention for their potential application in various coagulation tests. These sensors function by detecting resonant frequency shifts in response to changes in blood viscosity during coagulation. Nevertheless, the frequency-based detection approach necessitates continuous and precise frequency scanning, imposing stringent demands on equipment design, processing, and analytical techniques. In contrast, amplitude-based detection methods offer superior applicability in many sensing scenarios. This paper presents a comprehensive study on signal acquisition from magnetoelastic sensors. We elucidate the mathematical relationship between the resonant amplitude of the response signal and liquid viscosity, propose a quantitative viscosity measurement method based on the maximum amplitude of the signal, and construct a corresponding sensing device. The proposed method was validated using glycerol solutions, demonstrating a sensitivity of 13.83 V⁻¹/Pa^0.5s^0.5Kg^0.5m^−1.5 and a detection limit of 0.0817 Pa^0.5s^0.5Kg^0.5m^−1.5. When applied to real-time monitoring of the coagulation process, the resulting coagulation curves and maximum amplitude (MA) parameters exhibited excellent consistency with standard TEG results (R² values of 0.9552 and 0.9615, respectively). Additionally, other TEG parameters, such as R-time, K-time, and α-angle, were successfully obtained, effectively reflecting viscosity changes during blood coagulation. Full article

The photopolymerization process in 3D printing is considered greener once it involves a fast reaction and low energy consumption. Various reactions for photopolymerization can be used nowadays, but a special one is the thiol-ene “click” reaction that occurs in equimolar concentrations of thiol and alkene groups. In this sense, solvent-free photopolymerizable formulations were prepared to contain non-modified castor oil, Trimethylolpropane tris(3-mercapto propionate), and cellulosic fillers from hemp, tagua, and walnut. All formulations presented conversions higher than 70% and fast polymerization rates. Moreover, the filled formulations presented excellent curing depths in fewer seconds of light exposition, an important factor for their applicability in 3D printing. Furthermore, the hemp filler formulation presented the highest crosslinking density as determined by the DMTA, and was selected for printing two complex structures (pyramid and honeycomb shape). The rheology analysis showed that the formulations had adequate viscosities for the printer. Lastly, all polymers presented at least 97% bio-based contents, with gel contents superior to 96%. Full article

Electrochromic (EC) technology has become one of the smart technologies with the most potential for development and application at this stage. Based on electrochromic devices (ECDs), this technology has shown extraordinary potential in the fields of smart windows, display devices, and sensing systems. With the optimization and iteration of various core components in ECDs, the electrolyte layer, a key component, evolved from its initial liquid state to a quasi-solid state and solid state. As driven by increasing application demands, the development trend indicates that all-solid-state, transparent electrolytes will likely become the future form of the electrolyte layer. Recently, the application of ionic liquid (IL)-based electrolytes in the field of electrochromism attracted a lot of attention due to their ability to bring outstanding EC cycling stability, thermal stability, and a wider operating voltage range to ECDs, and they are regarded as the new generation of electrolyte materials with the most potential for application. Although compared with conventional electrolytes, IL-based electrolytes have the characteristics of high price, high viscosity, and low conductivity, they are still considered the most promising electrolyte materials for applications. However, so far, there has been a lack of comprehensive analysis reports on “Research progress in ionic liquid-based electrolytes for electrochromic devices” within the EC field. In this article, the research progress of IL-based electrolytes in ECDs will be summarized from three perspectives: liquid, quasi-solid, and solid state. The future development directions of IL-based electrolytes for ECDs are discussed. Full article

Spiropyran has an attractive and mysterious fluorescence switch and dual-color conversion characteristics, as it exhibits both aggregation-caused quenching (ACQ) in solvents and fluorescence enhancement in polymer matrices. The explanation for this phenomenon has always been of great controversy. Hence, the solvent effect on the emission of spiropyran (SP) was investigated in 16 solvents. By means of molecular orbital theory and the Jablonski diagram, several special parameters (e.g., Hansen solubility parameters and viscosity) were selected for this analysis, with excellent goodness of fit. Subsequently, the main factors that affected the blue shift, red shift, and luminescence efficiency of the emission of the ring-opened form merocyanine (MC) were found to be the hydrogen bonding and polarity, aggregation effect, and viscosity, respectively. A newly modified Jablonski diagram was proposed to clarify the emission behaviors of spiropyran influenced by solvent polarity and isomerization. Meanwhile, the solvent effect could also be extended to a solid polymer matrix (six kinds of polyethylene glycol (PEG) with different molecular weights), which is proposed to be defined as the generalized solvent effect. Accordingly, we have demonstrated that the unique fluorescence properties of spiropyran are dominated by the generalized solvent effect. The security information storage capacity of the simulated quick response (QR) code sensor combined with SP for anti-counterfeiting was significantly improved to six dimensions in taking advantage of the former theoretical analysis. Full article

Efficient separation of blood plasma and Packed Cell Volume (PCV) is vital for rapid blood sensing and early disease detection, especially in point-of-care and resource-limited environments. Conventional centrifugation methods for separation are resource-intensive, time-consuming, and off-chip, necessitating innovative alternatives. This study introduces “Intelligent Microfluidics”, an ML-integrated microfluidic platform designed to optimize plasma separation through computational fluid dynamics (CFD) simulations. The trifurcation microchannel, modeled using COMSOL Multiphysics, achieved plasma yields of 90–95% across varying inflow velocities (0.0001–0.05 m/s). The input fluid parameters mimic the blood viscosity and density used with appropriate boundary conditions and fluid dynamics to optimize the designed microchannels. Eight supervised ML algorithms, including Artificial Neural Networks (ANN) and k-Nearest Neighbors (KNN), were employed to predict key performance parameters, with ANN achieving the highest predictive accuracy (R² = 0.97). Unlike traditional methods, this platform demonstrates scalability, portability, and rapid diagnostic potential, revolutionizing clinical workflows by enabling efficient plasma separation for real-time, point-of-care diagnostics. By incorporating a detailed comparative analysis with previous studies, including computational efficiency, our work underscores the superior performance of ML-enhanced microfluidic systems. The platform’s robust and adaptable design is particularly promising for healthcare applications in remote or resource-constrained settings where rapid and reliable diagnostic tools are urgently needed. This novel approach establishes a foundation for developing next-generation, portable diagnostic technologies tailored to clinical demands. Full article

The efficient, economical, and sustainable production of biodiesel from waste cooking oils (WCOs) depends on the availability of simple, rapid, and low-cost methods to test the quality of potential feedstocks. The aim of this study was to establish the applicability of stochastic modeling of e-nose profiles in the evaluation of recycled WCO characteristics. Olfactory profiles of 10 WCOs were determined using a Sensigent Cyranose^® 320 chemical vapor-sensing device with a 32 sensor-array, and a stepwise multiple linear regression (MLR) analysis was performed to select stochastic parameters (explanatory variables) for inclusion in the final predictive models of the physicochemical properties of the WCOs. The most important model parameters for the characterization of WCOs were those relating to the time of inception of the e-nose signal “plateau” and to the concentration of volatile organic compounds (VOCs) in the sensor region. A comparison of acid values, peroxide values, water contents, and kinematic viscosities predicted by the MLR models with those determined by conventional laboratory methods revealed that goodness of fit and predictor accuracy varied from good to excellent, with all metric values >90%. Combining e-nose profiling with stochastic modeling was successful in predicting the physicochemical characteristics of WCOs and could be used to select suitable raw materials for efficient and sustainable biodiesel production. Full article

In the current environmental scenario, the proposal of alternatives for petroleum-based products has considerably increased, with the aim of looking for bioproducts with interesting properties such as biodegradability, sustainability and efficiency, among others. In this sense, the role of biolubricants is promising, offering a wide range of possibilities through different methods and operating conditions. Specifically, double transesterification could be a suitable process in a biorefinery context. The aim of this work was to produce a biolubricant through double transesterification with methanol and neopentyl glycol (NPG) under different reaction conditions by using homogeneous catalysis (sodium methoxide). Different catalyst concentrations, among other changes in reaction conditions (temperature ranging between 100 and 140 °C and NPG/FAME ratios between 0.5 and 2), were used, obtaining high conversion values (96%) and a final product with a high viscosity (20.7 cSt), which allows for its use as engine oil (SAE 5W). In conclusion, biodiesel and biolubricant production was feasible through homogeneous catalysis, proving the feasibility of this process at the laboratory scale. Further studies, including the use of different heterogeneous catalysts, as well as the implementation of this process at a semi-industrial scale, are recommended. Full article