Search Results (62)

Aqueous zinc-ion batteries are regarded a promising energy storage system due to their high safety, low cost, high theoretical specific capacity (820 mAh g⁻¹), and low redox potential (−0.76 V). However, in practice, uneven Zn²⁺ deposition on the surface of the zinc anode can lead to the uncontrolled growth of zinc dendrites, which can puncture the separator and trigger a short-circuit in the cell. In addition, the inherent thermodynamic instability of weakly acidic electrolytes is prone to trigger side reactions like hydrogen evolution reaction and corrosion, further weakening the stability of the zinc anode. These problems not only affect the cycle life of the battery, but also lead to a significant decrease in electrochemical performance. Therefore, how to effectively inhibit the unwanted side reactions and guide the uniform deposition of Zn²⁺ to suppress the growth of dendrites becomes a key challenge in constructing a stable zinc anode/electrolyte interface. Therefore, this paper systematically combs through the main bottlenecks and root causes that hinder the interfacial stability of zinc anodes at present, and summarizes the existing solutions and the progress made. On this basis, this paper also analyzes the application potential of polymer materials in enhancing the interfacial stability of zinc anodes, which provides new ideas for the direction of subsequent research. Full article

A novel bi-layered scaffold, obtained via 3D printing and electrospinning, was designed to improve osteochondral region reconstruction. The upper electrospun membrane will act as a barrier against unwanted tissue infiltration, while the lower 3D-printed layer will provide a porous structure for tissue ingrowth. Graphene was integrated into the scaffold for its antibacterial properties, and the drug Osteogenon^® (OST) was added to promote bone tissue regeneration. The composite scaffolds were subjected to comprehensive physical, thermal, and mechanical evaluations. Additionally, their biological functionality was assessed by means of NHAC-kn cells. The 0.5% graphene addition to PCL significantly increased strain at break, enhancing the material ductility. GNP also acted as an effective nucleating agent, raising crystallization temperatures and supporting mineralization. The high surface area of graphene facilitated rapid apatite formation by attracting calcium and phosphate ions. This was confirmed by FTIR, µCT and SEM analyses, which highlighted the positive impact of graphene on mineral deposition. The synergistic interaction between graphene nanoplatelets and Osteogenon^® created a bioactive environment that enhanced cell adhesion and proliferation, and promoted superior apatite formation. These findings highlight the scaffold’s potential as a promising biomaterial for osteochondral repair and regenerative medicine. Full article

Percutaneous Coronary Intervention (PCI) is a treatment method that involves reopening narrowed arteries with a balloon catheter that delivers a cylindrical, mesh-shaped implant device to the site of the stenosis. Currently, by applying a coating to a bare metal stent (BMS) surface to improve biocompatibility, the main risks after PCI, such as restenosis and thrombosis, are reduced while maintaining the basic requirements for the mechanical behavior of the stent itself. In this work, for the first time, the development and optimization process of the spatial structure of the Co-Cr stent (L-605) with a graphene-based coating using cold-wall chemical vapor deposition (CW-CVD) to ensure uniform coverage of the implant was attempted. The CW-CVD process allows the coating of 3D structures, minimizing thermal stress on the surrounding equipment and allowing the deposition of coatings on temperature-sensitive materials. It produces uniform and high-purity films with control over the thickness and composition. The reduced heating of the chamber walls minimizes unwanted reactions, leading to fewer impurities in the final coating. The graphene layers obtained using Raman spectroscopy at different parameters of the CW-CVD process were verified, their properties were investigated, and the functional mechanical behavior of the studied graphene-covered stent was confirmed. In vitro, graphene-coated stents promoted rapid endothelial cell repopulation, an advantage over gold-standard drug-eluting stents delaying re-endothelialization. Also, full-range biocompatibility studies on potential allergic, irritation, toxicological, and pyrogenic reactions of new material in vivo on small animal models demonstrated excellent biocompatibility of the graphene-coated stents. Full article

This study examined the potential application of metallic coatings to mitigate the adverse effects of ultraviolet (UV) and infrared (IR) light on photovoltaic modules. Titanium coatings were applied on low-iron glass surfaces using magnetron sputtering at powers of 1000, 1250, 1500, 1750, 2000, and 2500 W. The module with uncoated glass served as a reference. The Ti layer thickness varied from 7 nm to 20 nm. Transmittance and reflectance spectra were used to calculate visible light transmittance L_t, UV light transmittance L_tuv, solar transmittance g, and visible light reflectance L_r. The obtained parameters indicated that the thinnest Ti layer (1000 W) coating did not significantly affect light transmittance, but thicker layers did, altering the L_t, g, and L_r factors. However, every sample noticeably changed L_tuv, probably due to the natural formation of a UV-reflective thin TiO₂ layer. The differences in fill factor (FF) were minimal, but thicker coatings resulted in lower open-circuit voltages (U_oc) and short-circuit currents (I_sc), leading to a reduction in power conversion efficiency (PCE). Notably, a Ti coating deposited at 2500 W reduced the power of the photovoltaic module by 78% compared to the uncoated sample but may protect modules against the unwanted effects of overheating. Full article

The Central Australian red honey-pot ant Melophorus bagoti maintains non-cryptic ground-nesting colonies in the semi-desert habitat, performing all the activities outside the nest during the hottest periods of summer days. These ants rely on path integration and view-based cues for navigation. They manage waste by taking out unwanted food, dead nestmates, and some other wastes, typically depositing such items at distances > 5 m from the nest entrance, a process called dumping. We found that over multiple runs, dumpers headed in the same general direction, showing sector fidelity. Experienced ants dumped waste more efficiently than naive ants. Naive individuals, lacking prior exposure to the outdoor environment around the nest, exhibited much scanning and meandering during waste disposal. In contrast, experienced ants dumped waste with straighter paths and a notable absence of scanning behaviour. Furthermore, experienced dumpers deposited waste at a greater distance from the nest compared to their naive counterparts. We also investigated the navigational knowledge of naive and experienced dumpers by displacing them 2 m away from the nest. Naive dumpers were not oriented towards the nest in their initial trajectory at any of the 2 m test locations, whereas experienced dumpers were oriented towards the nest at all test locations. Naive dumpers were nest-oriented as a group, however, at the test location nearest to where they dumped their waste. These differences suggest that in red honey ants, learning supports waste disposal, with dumping being refined through experience. Dumpers gain greater spatial knowledge through repeated runs outside the nest, contributing to successful homing behaviour. Full article

In the present paper the humidity sensing properties of regioregular rr-P3HT (poly-3-hexylthiophene) polymer films is investigated by means of surface acoustic wave (SAW) based sensors implemented on LiNbO₃ (128⁰ Y-X) and ST-quartz piezoelectric substrates. The polymeric layers were deposited along the SAW propagation path by spray coating method and the layers thickness was measured by atomic force microscopy (AFM) technique. The response of the SAW devices to relative humidity (rh) changes in the range ~5–60% has been investigated by measuring the SAW phase and frequency changes induced by the (rh) absorption in the rr-P3HT layer. The SAW sensor implemented onto LiNbO₃ showed improved performance as the thickness of the membrane increases (from 40 to 240 nm): for 240 nm thick polymeric membrane a phase shift of about −1.2 deg and −8.2 deg was measured for the fundamental (~78 MHz operating frequency) and 3rd (~234 MHz) harmonic wave at (rh) = 60%. A thick rr-P3HT film (~600 nm) was deposited onto the quartz-based SAW sensor: the sensor showed a linear frequency shift of ~−20.5 Hz per unit (rh) changes in the ~5–~50% rh range, and a quite fast response (~5 s) even at low humidity level (~5% rh). The LiNbO₃ and quartz-based sensors response was assessed by using a dual delay line system to reduce unwanted common mode signals. The simple and cheap spray coating technology for the rr-P3HT polymer films deposition, complemented with fast low level humidity detection of the tested SAW sensors (much faster than the commercially available Michell SF-52 device), highlight their potential in a low-medium range humidity sensing application. Full article

This study investigates the mechanical properties, surface integrity, and chemical configuration of PVD-coated high-speed steel (HSS) cutting tools, with a particular focus on titanium nitride (TiN) and titanium aluminium nitride (TiAlN) coatings. A range of characterisation methodologies were employed to examine the impact of pre-coating surface conditions on the resulting coatings. This impact includes the effects of gas bubble production and unequal distribution of elements, which are two unwanted occurrences. Notwithstanding these difficulties, coatings applied on surfaces that were highly polished exhibited more consistency in their mechanical and elemental characteristics, with a thickness ranging from 2 to 4 µm. The study of mechanical characteristics confirms a significant increase in hardness, from an initial value of roughly 1000 HV0.5 for untreated tools to 1300 HV0.5 for tools with physical vapour deposition (PVD) coatings. Although PVD coatings produced on an industrial scale might not exceed the quality of coatings manufactured in a laboratory, they do offer substantial enhancements in terms of hardness. This study highlights the significant importance of thorough surface preparation in achieving enhanced coating performance, hence contributing to the efforts to prolong the lifespan of tools and enhance their performance even under demanding operational circumstances. Full article

The use of poultry litter (PL) as a sustainable fuel is gaining more attention due to its wide availability and carbon neutrality. However, this type of feedstock is rich in ash and typically contains a high concentration of chlorine (Cl) and alkali elements (Na, K). Therefore, it is likely to cause unwanted issues during combustion and co-combustion, such as chlorine-induced corrosion, ash deposition, and bed agglomeration. In this study, for the first time, the influence of aluminosilicate additives on the above problems of poultry litter was investigated. Three aluminosilicate minerals are under consideration: kaolin, halloysite, and bentonite. Their influence on the chemical composition and meting tendencies of two poultry litter ashes are determined. The investigated ashes, PL1 and PL2, are characterized by different chlorine contents of 6.38% and 0.42%, respectively. The results show that in the case of the chlorine-rich PL1 ash, the additives reduced the chlorine content by up to 45%, resulting in a 3.93% of chlorine in the case of halloysite, 3.48% in the case of kaolin, and 4.25% in the case of bentonite. The additives also positively influenced the shrinkage starting temperature and the deformation temperature of the PL1 ash. Full article

The bulk-heterojunction (BHJ) system that uses a $\pi$-conjugated polymer as an electron donor, and a fullerene derivative as an electron acceptor, is widely used in organic solar cells (OSCs) to facilitate efficient charge separation and extraction. However, the conventional BHJ system still suffers from unwanted phase segregation caused by the existence of significant differences in surface energy between the two BHJ components and the charge extraction layer during film formation. In the present work, we demonstrate a sophisticated control of fast film-growth kinetics that can be used to achieve a uniform distribution of donor and acceptor materials in the BHJ layer of OSCs without undesirable phase separation. Our approach involves depositing the BHJ solution onto a spinning substrate, thus inducing rapid evaporation of the solvent during BHJ film formation. The fast-growth process prevents the fullerene derivative from migrating toward the charge extraction layer, thereby enabling a homogeneous distribution of the fullerene derivative within the BHJ film. The OSCs based on the fast-growth BHJ thin film are found to exhibit substantial increases in J_SC, fill factor, and a PCE up to 11.27 mA/cm², 66%, and 4.68%, respectively; this last value represents a remarkable 17% increase in PCE compared to that of conventional OSCs. Full article

TiN-Ag ceramic coatings deposited by magnetron sputtering on silicon wafers and AISI F138 stainless-steel substrates with different Ag concentrations were evaluated for their application as decorative coatings. The results obtained indicated an almost linear increase in the thickness and roughness of the film as a function of the increase in the silver content of the film. For Ag concentrations greater than (8.3 ± 0.5) at %, a matte/satin finish was observed, i.e., a dull surface, produced by the agglomeration of particulates and the increase in roughness, respectively, which was corroborated by SEM and AFM analyses. The EDS analyses indicated particles with a high concentration of silver, but the elements titanium and nitrogen were also observed, indicating the formation of the TiN-Ag coating. The L*a*b* parameters in the CIELab color space were evaluated. No major variations were observed for coatings A and B (Ag concentrations of (4.1 ± 0.4) and (6.3 ± 1.2) at %, respectively). When the Ag content increased substantially, there was a corresponding decrease in L* values, as well as a shift in red reflectance. Furthermore, unwanted changes in the visual appearance and resistance to accelerated corrosion (salt spray) were also analyzed, as these factors compromised the film’s aesthetics in decorative applications. Full article

Graphene materials synthesized using direct laser writing (laser-induced graphene; LIG) make favorable sensor materials because of their large surface area, ease of fabrication, and cost-effectiveness. In particular, LIG decorated with metal nanoparticles (NPs) has been used in various sensors, including chemical sensors and electronic and electrochemical biosensors. However, the effect of metal decoration on LIG sensors remains controversial; hypotheses based on computational simulations do not always match the experimental results, and even the experimental results reported by different researchers have not been consistent. In the present study, we explored the effects of metal decorations on LIG gas sensors, with NO₂ and NH₃ gases as the representative oxidizing and reducing agents, respectively. To eliminate the unwanted side effects arising from metal salt residues, metal NPs were directly deposited via vacuum evaporation. Although the gas sensitivities of the sensors deteriorate upon metal decoration irrespective of the metal work function, in the case of NO₂ gas, they improve upon metal decoration in the case of NH₃ exposure. A careful investigation of the chemical structure and morphology of the metal NPs in the LIG sensors shows that the spontaneous oxidation of metal NPs with a low work function changes the behavior of the LIG gas sensors and that the sensors’ behaviors under NO₂ and NH₃ gases follow different principles. Full article

Inappropriate fertilisation results in the pollution of groundwater with nitrates and phosphates, eutrophication in surface water, emission of greenhouse gasses, and unwanted N deposition in natural environments, thereby harming the whole ecosystem. In greenhouses, the cultivation in closed-loop soilless culture systems (CLSs) allows for the collection and recycling of the drainage solution, thus minimising contamination of water resources by nutrient emissions originating from the fertigation effluents. Recycling of the DS represents an ecologically sound technology as it can reduce water consumption by 20–35% and fertiliser use by 40–50% in greenhouse crops, while minimising or even eliminating losses of nutrients, thereby preventing environmental pollution by NO₃⁻ and P. The nutrient supply in CLSs is largely based on the anticipated ratio between the mass of a nutrient absorbed by the crop and the volume of water, expressed as mmol L⁻¹, commonly referenced to as “uptake concentration” (UC). However, although the UCs exhibit stability over time under optimal climatic conditions, some deviations at different locations and different cropping stages can occur, leading to the accumulation or depletion of nutrients in the root zone. Although these may be small in the short term, they can reach harmful levels when summed up over longer periods, resulting in serious nutrient imbalances and crop damage. To prevent large nutrient imbalances in the root zone, the composition of the supplied nutrient solution must be frequently readjusted, taking into consideration the current nutrient status in the root zone of the crop. The standard practice to estimate the current nutrient status in the root zone is to regularly collect samples of drainage solution and determine the nutrient concentrations through chemical analyses. However, as results from a chemical laboratory are available several days after sample selection, there is currently intensive research activity aiming to develop ion-selective electrodes (ISEs) for online measurement of the DS composition in real-time. Furthermore, innovative decision support systems (DSSs) fed with the analytical results transmitted either offline or online can substantially contribute to timely and appropriate readjustments of the nutrient supply using as feedback information the current nutrient status in the root zone. The purpose of the present paper is to review the currently applied technologies for nutrient and water recycling in CLSs, as well as the new trends based on ISEs and novel DSSs. Furthermore, a specialised DSS named NUTRISENSE, which can contribute to more efficient management of nutrient supply and salt accumulation in closed-loop soilless cultivations, is presented. Full article

This paper provides an overview of the cleaning aspects of solar panels through a literature review. We first discuss the drawbacks of unwanted deposits on solar panels in terms of energy production and efficiency. Existing cleaning practices and technologies are then presented with an emphasis on factors such as the size of the facility, location, cost, and available resources. Finally, a comparative cost–benefit analysis is carried out using decision support tools and taking into account different relevant criteria to support users choose the right cleaning maintenance for their specific solar installation. Full article

This study aims to explore the effects of ultrasonic impact parameters on the surface modification of a stainless steel coating deposited on a medium-carbon low-alloy steel using argon arc surfacing welding. Ultrasonic impact treatment (UIT), at three different vibration strike numbers (40,000 times/(mm²), 57,600 times/(mm²), and 75,000 times/(mm²)) marked UIT–1, UIT–2, and UIT–3, respectively, was carried out to modify the surface structure and properties of the stainless steel coating. The surface morphological and structural features, phase compositions, grain size, topography, micro-mechanical properties, as well as the wear resistance of the coating before and after UIT with different impact parameters were experimentally investigated. The results of optical microscopy (OM), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), and X-ray diffraction (XRD) analyses revealed that the grain refinement accompanied by the formation of the strain-induced α′–martensite occurred on the UIT-treated coating surface. With the increase in the vibration strike number, the surface grain size and roughness decreased, while the α′–martensite content increased. Micro-hardness after UIT was increased by about 19% (UIT–1), 39% (UIT–2), and 57% (UIT–3), and the corresponding wear rate obtained was decreased by 39%, 72%, and 85%, respectively. Significant improvements in wear resistance were achieved using UIT. However, an excessive vibration strike number on the per unit area (/mm²) might result in unwanted micro-cracks and delamination on the treated surface, deteriorating the performance of the coating. These findings validate that UIT parameters (such as the vibration strike number on per unit area) are of great importance to bringing about improvements in wear performance, and UIT is found to have a high potential in modifying the surface characteristics and optimizing the mechanical performances of the deposited coating for a wide range of potential applications. Full article

Metal-based high-touch surfaces used for diverse applications in everyday use, like handrails, playground grab handles, doorknobs, ATM touch pads, and desks, are the most common targets for pollution with a variety of microbes; there is thus a need to improve their antimicrobial properties, an issue which has become a challenge in recent years, particularly after the COVID-19 pandemic. According to the World Health Organization (WHO), drug-resistant pathogens are one of the main concerns to global health today, as they lead to longer hospital stays and increased medical costs. Generally, the development of antimicrobial surfaces is related to the utilization of chemical methods via deposition on surfaces in the forms of various types of coatings. However, the addition of chemical substances onto a surface can induce unwanted effects, since it causes surface chemistry changes and, in some cases, cannot provide long-lasting results. A novel approach of utilising ultra-short laser radiation for the treatment of metallic surfaces by inducing a variety of micro- and nanostructuration is elaborated upon in the current research, estimating the optimum relation between the wettability and roughness characteristics for the creation of antimicrobial properties for such high-touch surfaces. In the current study, AISI 304–304L stainless steel metal was used as a benchmark material. Surface texturing via laser ablation with femtosecond laser pulses is an effective method, since it enables the formation of a variety of surface patterns, along with the creation of bimodal roughness, in one-step processing. In this investigation, a precise approach toward developing hydrophobic stainless steel surfaces with tunable adherence using femtosecond laser-induced modification is described. The impact of basic femtosecond laser processing parameters, like the scanning velocity, laser energy, and wettability properties of the laser-processed stainless steel samples, are examined. It is identified that the topography and morphology of laser-induced surface structures can be efficiently changed by adapting the laser processing parameters to create structures, which facilitate the transfer of surface properties from extremely low to high surface wettability. Full article