Search Results (842)

This paper presents a novel design for precise vertical landing of drones based on the detection of three phase shifts in the range of ±180°. The design has three inputs to which the signal transmitted from an oscillator located at the landing point arrives with different delays. The circuit increases the aerial tracking volume relative to that achieved by detectors with theoretical unambiguous detection ranges of ±90°. The phase shift measurement circuit uses an analog phase detector (mixer), detecting a maximum range of ±90°and a double multiplication of the input signals, in phase and phase-shifted, without the need to fulfill the quadrature condition. The calibration procedure, phase detector curve modeling, and calculation of the input signal phase shift are significantly simplified by the use of an automatic gain control on each branch, dwhich keeps input amplitudes to the analog phase detectors constant. A simple program to determine phase shifts and guidance instructions is proposed, which could be integrated into the same flight control platform, thus avoiding the need to add additional processing components. A prototype has been manufactured in C band to explain the details of the procedure design. The circuit uses commercial circuits and microstrip technology, avoiding the crossing of lines by means of switches, which allows the design topology to be extrapolated to much higher frequencies. Calibration and measurements at 5.3 GHz show a dynamic range greater than 50 dB and a non-ambiguous detection range of ±180°. These specifications would allow one to track the drone during the landing maneuver in an inverted cone formed by a surface with an 11 m radius at 10 m high and the landing point, when 4 cm between RF inputs is considered. The errors of the phase shifts used in the landing maneuver are less than ±3°, which translates into 1.7% losses over the detector theoretical range in the worst case. The circuit has a frequency bandwidth of 4.8 GHz to 5.6 GHz, considering a 3 dB variation in the input power when the AGC is limiting the output signal to 0 dBm at the circuit reference point of each branch. In addition, the evolution of phases in the landing maneuver is shown by means of a small simulation program in which the drone trajectory is inside and outside the tracking range of ±180°. Full article

The organic Rankine cycle (ORC) is a key technology for the recovery of low-grade waste heat, but its efficient and stable operation is challenged by complex kinetic coupling. This paper proposes a model partitioning strategy based on gap measurement to construct a high-fidelity ORC system model and combines the setting of observer decoupling and multi-model switching strategies to reduce the coupling impact and enhance adaptability. For control optimization, the reinforcement learning method of deep deterministic Policy Gradient (DDPG) is adopted to break through the limitations of the traditional discrete action space and achieve precise optimization in the continuous space. The proposed DDPG-MGPC (Hybrid Model Predictive Control) framework significantly enhances robustness and adaptability through the synergy of reinforcement learning and model prediction. Simulation shows that, compared with the existing hybrid reinforcement learning and MPC methods, DDPG-MGPC has better tracking performance and anti-interference ability under dynamic working conditions, providing a more efficient solution for the practical application of ORC. Full article

Trajectory planning is crucial for solar aircraft endurance. The multi-wing morphing solar aircraft can enhance solar energy acquisition through wing deflection, which simultaneously incurs aerodynamic losses, complicating energy coupling and challenging existing planning methods in efficiency and long-term optimization. This study presents an energy-optimal trajectory planning method based on Hierarchical Reinforcement Learning for morphing solar-powered Unmanned Aerial Vehicles (UAVs), exemplified by a Λ-shaped aircraft. This method aims to train a hierarchical policy to autonomously track energy peaks. It features a top-level decision policy selecting appropriate bottom-level policies based on energy factors, which generate control commands such as thrust, attitude angles, and wing deflection angles. Shaped properly by reward functions and training conditions, the hierarchical policy can enable the UAV to adapt to changing flight conditions and achieve autonomous flight with energy maximization. Evaluated through 24 h simulation flights on the summer solstice, the results demonstrate that the hierarchical policy can appropriately switch its bottom-level policies during daytime and generate real-time control commands that satisfy optimal energy power requirements. Compared with the minimum energy consumption benchmark case, the proposed hierarchical policy achieved 0.98 h more of full-charge high-altitude cruise duration and 1.92% more remaining battery energy after 24 h, demonstrating superior energy optimization capabilities. In addition, the strong adaptability of the hierarchical policy to different quarterly dates was demonstrated through generalization ability testing. Full article

In recent years, pneumatic stages have attracted attention as stages for semiconductor manufacturing equipment due to their low cost and minimal maintenance requirements. However, pneumatic stages include nonlinear elements such as friction and air compressibility, making precise control challenging. To address this issue, this paper aims to achieve high-precision positioning by applying a nonlinear position control method to pneumatic stages. To achieve this, we propose a control method that combines filtered right coprime factorization and Prescribed Performance Control–Sliding Mode Control (PPC-SMC). Filtered right coprime factorization not only stabilizes and simplifies the plant but also reduces noise. Furthermore, PPC-SMC enables safer and faster control by constraining the system state within a switching surface that imposes limits on the error range. Through experiments on the actual system, it was confirmed that the proposed method achieves dramatically higher precision and faster tracking compared to conventional methods. Full article

Accurate and automated detection and tracking of cells in microscopy images is a persistent challenge in biotechnology and biomedical research. Effective detection and tracking are crucial for understanding biological processes and extracting meaningful data for subsequent simulations. In this study, we present an integrated pipeline that leverages a fine-tuned YOLOv8x model for detecting cells and cell divisions across microscopy image series. While YOLOv8x exhibits strong detection capabilities, it occasionally misses certain cells, leading to gaps in data. To mitigate this, we incorporate the DeepSORT tracking algorithm, which enhances data association and reduces the cells’ identity (ID) switches by utilizing a pre-trained convolutional network for robust multi-object tracking. This combination ensures continuous detection and compensates for missed detections, thereby improving overall recall. Our approach achieves a recall of 93.21% with the enhanced DeepSORT algorithm, compared to the 53.47% recall obtained by the original YOLOv8x model. The proposed pipeline effectively extracts detailed information from structured image datasets, providing a reliable approximation of cellular processes in culture environments. Full article

Sound event localization and detection (SELD) is a fundamental task in spatial audio processing that involves identifying both the type and location of sound events in acoustic scenes. Current SELD models often struggle with low signal-to-noise ratios (SNRs) and high reverberation. This article addresses SELD by reformulating direction of arrival (DOA) estimation as a multi-class classification task, leveraging deep convolutional recurrent neural networks (CRNNs). We propose and evaluate two modified architectures: M-DOAnet, an optimized version of DOAnet for localization and tracking, and M-SELDnet, a modified version of SELDnet, which has been designed for joint SELD. Both modified models were rigorously evaluated on the STARSS23 dataset, which comprises 13-class, real-world indoor scenes totaling over 7 h of audio, using spectrograms and acoustic intensity maps from first-order Ambisonics (FOA) signals. M-DOAnet achieved exceptional localization (6.00° DOA error, 72.8% F1-score) and perfect tracking (100% MOTA with zero identity switches). It also demonstrated high computational efficiency, training in 4.5 h (164 s/epoch). In contrast, M-SELDnet delivered strong overall SELD performance (0.32 rad DOA error, 0.75 F1-score, 0.38 error rate, 0.20 SELD score), but with significantly higher resource demands, training in 45 h (1620 s/epoch). Our findings underscore a clear trade-off between model specialization and multifunctionality, providing practical insights for designing SELD systems in real-time and computationally constrained environments. Full article

This paper addresses the issues of sensor failures and actuator faults in mining tracked mobile vehicles (TMVs) operating in harsh environments by proposing a global fixed-time fault-tolerant control strategy based on a hierarchical unknown input observer structure. First, a kinematic and dynamic model of the TMV is established considering side slip and track slip, and its linear parameter-varying (LPV) model is constructed through parameter-dependent linearization. Then, a distributed structure consisting of four collaborating low-dimensional observers is designed, including a state observer, a disturbance observer, a position sensor fault observer, and a wheel speed sensor fault observer, and the fixed-time convergence of the closed-loop system is proven. Additionally, by equivalently treating actuator faults as power losses, an observer capable of identifying and compensating for motor efficiency losses is designed. Finally, an adaptive fault-tolerant control law is proposed by combining nominal control, disturbance compensation, and sliding mode switching terms, achieving global fixed-time stability and fault tolerance. Experimental results demonstrate that the proposed control system maintains excellent trajectory tracking performance even in the presence of sensor faults and actuator power losses, with tracking errors less than 0.1 m. Full article

This paper presents an adaptive Maximum Power Point Tracking (MPPT) strategy for grid-connected photovoltaic (PV) systems that uses an Adaptive Neuro-Fuzzy Inference System (ANFIS) optimized by Particle Swarm Optimization (PSO) to enhance energy extraction efficiency under diverse environmental conditions. The proposed ANFIS-PSO-based MPPT controller performs dynamic adjustment Pulse Width Modulation (PWM) switching to minimize Total Harmonic Distortion (THD); this will ensure rapid convergence to the maximum power point (MPP). Unlike conventional Perturb and Observe (P&O) and Incremental Conductance (INC) methods, which struggle with tracking delays and local maxima in partial shading scenarios, the proposed approach efficiently identifies the Global Maximum Power Point (GMPP), improving energy harvesting capabilities. Simulation results in MATLAB/Simulink R2023a demonstrate that under stable irradiance conditions (1000 W/m², 25 °C), the controller was able to achieve an MPPT efficiency of 99.2%, with THD reduced to 2.1%, ensuring grid compliance with IEEE 519 standards. In dynamic irradiance conditions, where sunlight varies linearly between 200 W/m² and 1000 W/m², the controller maintains an MPPT efficiency of 98.7%, with a response time of less than 200 ms, outperforming traditional MPPT algorithms. In the partial shading case, the proposed method effectively avoids local power maxima and successfully tracks the Global Maximum Power Point (GMPP), resulting in a power output of 138 W. In contrast, conventional techniques such as P&O and INC typically fail to escape local maxima under similar conditions, leading to significantly lower power output, often falling well below the true GMPP. This performance disparity underscores the superior tracking capability of the proposed ANFIS-PSO approach in complex irradiance scenarios, where traditional algorithms exhibit substantial energy loss due to their limited global search behavior. The novelty of this work lies in the integration of ANFIS with PSO optimization, enabling an intelligent self-adaptive MPPT strategy that enhances both tracking speed and accuracy while maintaining low computational complexity. This hybrid approach ensures real-time adaptation to environmental fluctuations, making it an optimal solution for grid-connected PV systems requiring high power quality and stability. The proposed controller significantly improves energy harvesting efficiency, minimizes grid disturbances, and enhances overall system robustness, demonstrating its potential for next-generation smart PV systems. Full article

The increasing integration of renewable energy, electric vehicles, and industrial applications demands efficient power converter control strategies that reduce switching losses while maintaining high waveform quality. This paper presents a Finite-Control-Set Model Predictive Control (FCS-MPC) strategy for three-phase, two-level voltage source inverters (VSIs), incorporating a secondary objective for switching frequency minimization. Unlike conventional MPC approaches, the proposed method optimally balances control performance and efficiency trade-offs by adjusting the weighting factor (${\lambda }_{min}$). Real-time implementation using the OPAL-RT platform validates the effectiveness of the approach under both linear and non-linear load conditions. Results demonstrate a significant reduction in switching losses, accompanied by improved waveform tracking; however, trade-offs in distortion are observed under non-linear load scenarios. These findings provide insights into the practical implementation of real-time predictive control strategies for high-performance power converters. Full article

Hypersonic morphing vehicles (HMVs), renowned for their adaptive structural reconfiguration and cross-domain maneuverability, confront formidable reentry guidance challenges under multiple no-fly zones, stringent path constraints, and nonlinear dynamics exacerbated by morphing-induced aerodynamic uncertainties. To address these issues, this study proposes a hierarchical framework integrating an A-based energy-optimal waypoint planner, a deep deterministic policy gradient (DDPG)-driven morphing policy network, and a quasi-equilibrium glide condition (QEGC) guidance law with continuous sliding mode control. The A* algorithm generates heuristic trajectories circumventing no-fly zones, reducing the evaluation function by 6.2% compared to greedy methods, while DDPG optimizes sweep angles to minimize velocity loss and terminal errors (0.09 km position, 0.01 m/s velocity). The QEGC law ensures robust longitudinal-lateral tracking via smooth hyperbolic tangent switching. Simulations demonstrate generalization across diverse targets (terminal errors < 0.24 km) and robustness under Monte Carlo deviations (0.263 ± 0.184 km range, −12.7 ± 42.93 m/s velocity). This work bridges global trajectory planning with real-time morphing adaptation, advancing intelligent HMV control. Future research will extend this framework to ascent/dive phases and optimize its computational efficiency for onboard deployment. Full article

Precise identification and quantification of fish movement states are of significant importance for conducting fish behavior research and guiding aquaculture production, with object tracking serving as a key technical approach for achieving behavioral quantification. The traditional DeepSORT algorithm has been widely applied to object tracking tasks; however, in practical aquaculture environments, high-density cultured fish exhibit visual characteristics such as similar textural features and frequent occlusions, leading to high misidentification rates and frequent ID switching during the tracking process. This study proposes an underwater fish object tracking method based on the improved DeepSORT algorithm, utilizing ResNet as the backbone network, embedding Deformable Convolutional Networks v2 to enhance adaptive receptive field capabilities, introducing Triplet Loss function to improve discrimination ability among similar fish, and integrating Convolutional Block Attention Module to enhance key feature learning. Finally, by combining the aforementioned improvement modules, the ReID feature extraction network was redesigned and optimized. Experimental results demonstrate that the improved algorithm significantly enhances tracking performance under frequent occlusion conditions, with the MOTA metric improving from 64.26% to 66.93% and the IDF1 metric improving from 53.73% to 63.70% compared to the baseline algorithm, providing more reliable technical support for underwater fish behavior analysis. Full article

Indoor localization techniques operate independently of Global Navigation Satellite Systems (GNSSs), which are primarily designed for outdoor environments. However, integrating indoor and outdoor positioning often leads to inconsistent and delayed location estimates, especially at transition zones such as building entrances. This paper develops a probabilistic transition detection algorithm to identify indoor, outdoor, and transition zones, aiming to enhance the continuity and accuracy of positioning. The algorithm leverages multi-source sensor data, including WiFi Received Signal Strength Indicator (RSSI), Bluetooth Low-Energy (BLE) RSSI, and GNSS metrics such as carrier-to-noise ratio. During transitions, the system incorporates Inertial Measurement Unit (IMU)-based tracking to ensure smooth switching between positioning engines. The outdoor engine utilizes a Kalman Filter (KF) to fuse IMU and GNSS data, while the indoor engine employs fingerprinting techniques using WiFi and BLE. This paper presents experimental results using three distinct devices across three separate buildings, demonstrating superior performance compared to both Google’s Fused Location Provider (FLP) algorithm and a GPS. Full article

Dual Maximum Power Point Tracking (MPPT) inverters are essential in residential and small commercial solar power systems, optimizing power extraction from two independent solar panel arrays to enhance efficiency and energy harvesting. On the other hand, the Three-Level T-Type Voltage Source Inverter (3L T-Type VSI) is known for its reduced switching losses, improved harmonic distortion, and reduced part count in comparison to other three-level topologies. In this paper, a novel architecture is proposed to integrate the dual MPPT structure directly to each DC-side split capacitor of the 3L T-Type VSI, taking advantage of the intrinsic characteristics of the inverter’s topology. Further performance enhancement is achieved by integrating a classical MPPT strategy to the control framework to make it feasible for a real-case grid integration. The combination of these methods ensures faster and stable tracking under dynamic irradiance conditions. Considering that strategies dedicated to balancing the DC-link capacitor’s voltage slightly affect the AC-side current waveform, an enhanced sliding mode control (SMC) strategy tailored for dual MPPT and 3L T-Type VSI is deployed, combining the simplicity of conventional PI controllers used in the independent MPPT-based DC-DC converters with the superior robustness and dynamic performance of SMC. Real-time results obtained using the OPAL-RT Hardware-in-the-Loop platform validated the performance of the proposed control strategy under realistic test scenarios. The current THD was maintained below 4.8% even under highly distorted grid conditions, and the controller achieved a steady state within approximately 15 ms following perturbations in the DC-link voltage, sudden irradiance variations, and voltage sags and swells. Additionally, the power factor remained unitary, enhancing power transfer from the renewable source to the grid. The proposed system was able to achieve efficient power extraction while maintaining high power quality (PQ) standards for the output, positioning it as a practical and flexible solution for advanced solar PV systems. Full article

This paper proposes a robust voltage control strategy for grid-forming (GFM) inverters in distribution networks to achieve power support and voltage optimization. Specifically, the GFM control approach primarily consists of a power synchronization loop, a voltage feedforward loop, and a current control loop. A voltage feedforward control circuit is presented to achieve error-free tracking of voltage amplitude and phase. In particular, the current gain is designed to replace voltage feedback for improving the current response and simplifying the control structure. Additionally, in order to optimize voltage and improve the power quality at the terminal of the distribution network, an optimization model for distribution transformers is established with the goal of the maximum qualified rate of the load-side voltage and minimum switching times of transformer tap changers. An enhanced whale optimization algorithm (EWOA) is designed to complete the algorithm solution, thereby achieving the optimal system configuration, where an improved attenuation factor and position updating mechanism is proposed to enhance the EWOA’s global optimization capability. The simulation results demonstrate the validity and feasibility of the proposed strategy. Full article

Traditional Multiple Object Tracking (MOT) methods in satellite videos mostly follow the Detection-Based Tracking (DBT) framework. However, the DBT framework assumes that all objects are correctly recognized and localized by the detector. In practice, the low resolution of satellite videos, small objects, and complex backgrounds inevitably leads to a decline in detector performance. To alleviate the impact of detector degradation on track, we propose Coarse-Fine Tracker, a framework that integrates the MOT framework with the Tracking Any Point (TAP) method CoTracker for the first time, leveraging TAP’s persistent point correspondence modeling to compensate for detector failures. In our Coarse-Fine Tracker, we divide the satellite video into sub-videos. For one sub-video, we first use ByteTrack to track the outputs of the detector, referred to as coarse tracking, which involves the Kalman filter and box-level motion features. Given the small size of objects in satellite videos, we treat each object as a point to be tracked. We then use CoTracker to track the center point of each object, referred to as fine tracking, by calculating the appearance feature similarity between each point and its neighboring points. Finally, the Consensus Fusion Strategy eliminates mismatched detections in coarse tracking results by checking their geometric consistency against fine tracking results and recovers missed objects via linear interpolation or linear fitting. This method is validated on the VISO and SAT-MTB datasets. Experimental results in VISO show that the tracker achieves a multi-object tracking accuracy (MOTA) of 66.9, a multi-object tracking precision (MOTP) of 64.1, and an IDF1 score of 77.8, surpassing the detector-only baseline by 11.1% in MOTA while reducing ID switches by 139. Comparative experiments with ByteTrack demonstrate the robustness of our tracking method when the performance of the detector deteriorates. Full article