Search Results (176)

Electrohydrodynamic (EHD) printing offers mask-free, high-resolution deposition across a broad range of ink viscosities, yet combining void-free filling of high-aspect-ratio through-glass vias (TGVs) with ultrafine drop-on-demand (DOD) line printing on the same platform requires balancing conflicting requirements: for example, high field strengths to drive ink into deep and narrow vias; sufficiently high ink viscosity to prevent gravity-induced leakage; and stable meniscus dynamics to avoid satellite droplets and charge accumulation on the glass surface. By coupling electrostatic field analysis with transient level-set simulations, we establish a dimensionless regime map that delineates stable cone-jetting regime; these predictions are validated by high-speed imaging and surface profilometry. Operating within this window, the platform achieves complete, void-free filling of 200 µm × 1.52 mm TGVs and continuous 10 µm-wide traces in a single print pass. Demonstrating its capabilities, we fabricate transparent Ku-band substrate-integrated waveguide antennas on borosilicate glass: the printed vias and arc feed elements exhibit a reflection coefficient minimum of −18 dB at 14.2 GHz, a −10 dB bandwidth of 12.8–16.2 GHz, and an 8 dBi peak gain with 37° beam tilt, closely matching full-wave predictions. This physics-driven, all-in-one EHD approach provides a scalable route to high-performance, glass-integrated RF devices and transparent electronics. Full article

Millimeter-wave frequencies are crucial for meeting the high-capacity, low-latency demands of 5G communication systems, thereby driving the need for compact, high-gain antenna arrays capable of efficient beamforming. This paper presents the design, simulation, fabrication, and experimental validation of a compact, high-efficiency 1 × 6 linear series-fed microstrip patch antenna array for 5G millimeter-wave communication operating at 28 GHz. The proposed antenna is fabricated on a low-loss Rogers RO3003 substrate and incorporates an integrated symmetric two-way microstrip power divider to ensure balanced feeding and phase uniformity across elements. The antenna achieves a simulated peak gain of 11.5 dBi and a broad simulated impedance bandwidth of 30.21%, with measured results confirming strong impedance matching and a return loss better than −20 dB. The far-field radiation patterns demonstrate a narrow, highly directive beam in the E-plane, and the H-plane results reveal beam tilting behavior, validating the antenna’s capability for passive beam steering through feedline geometry and element spacing (~0.5λ). Surface current distribution analysis confirms uniform excitation and efficient radiation, further validating the design’s stability. The fabricated prototype shows excellent agreement with the simulation, with minor discrepancies attributed to fabrication tolerances. These results establish the proposed antenna as a promising candidate for applications requiring compact, high-gain, and beam-steerable solutions, such as 5G mm-wave wireless communication systems, point-to-point wireless backhaul, and automotive radar sensing. Full article

To address the issue of structural tilting caused by uneven foundation settlement in soft soil areas, this study combined a specific engineering case to conduct numerical simulations of the rectification process for an inclined reinforced concrete building using ABAQUS finite element software. Micropile-raft combined jacking technology was employed, applying staged jacking forces (2400 kN for Axis A, 2200 kN for Axis B, and 1700 kN for Axis C) with precise control through 20 incremental steps. The results demonstrate that this technology effectively halted structural tilting, reducing the maximum inclination rate from 0.51% to 0.05%, significantly below the standard limit. Post-rectification, the peak structural stress decreased by 42%, and displacements were markedly reduced. However, the jacking process led to a notable increase in the column axial forces and directional changes in beam bending moments, reflecting the dynamic redistribution of internal forces. The study confirms that micropile-raft combined jacking technology offers both controllability and safety, while optimized counterforce pile layouts enhance the long-term stability of the rectification system. Based on stress and displacement cloud analysis, a monitoring scheme is proposed, forming an integrated “rectification-monitoring-reinforcement” solution, which provides a technical framework for building rectification in soft soil regions. Full article

The dynamic response of multi-story steel frames under impact loading exhibits a complex nonlinear behavior. This study develops a three-story, multi-scale spatial steel frame finite element model using ABAQUS 2023 software, and the contact algorithm and material parameters were validated through published drop-weight impact beam tests. A total of 48 impact parameter combinations were defined, covering rational mass–velocity ranges while accounting for column position variations at the first story. Systematic comparisons were conducted on the influence of varying impact parameters on structural dynamic responses. This study investigates deformation damage and progressive collapse mechanisms in spatial steel frames under impact loading. Structural dynamic responses show significant enhancement with increasing impact mass and velocity. As impact kinetic energy increases, the steel frame transitions from localized denting at impact zones to global bending deformation, inducing structural tilting. The steel frame exhibits potential collapse risk under severe impact conditions. Under identical impact energy, corner column impact displacements differ by <1% from edge-middle column displacements, with vertical displacement variations ranging 0–17.6%. The displacement of the first-floor joints of the structure with three spans in the impact direction was reduced by about 50% compared to that with two spans. When designing the structure, it is necessary to increase the number of frame spans in the impact direction to improve the overall stability of the structure. Based on the development of the rotation angle of the beam members during the impact process, the steel frame collapse process was divided into three stages, the elastic stage, the plastic and catenary stage, and the column member failure stage; the steel frame finally collapsed due to an excessive beam rotation angle and column failure. Full article

Millimeter-wave antennas have become more important recently due to the diversity of applications in 5G and upcoming 6G technologies, of which automotive systems constitute a significant part. Two crucial indices, detection range and angular resolution, are used to distinguish the performance of the automotive antenna. Strong gains and narrow beamwidths of highly directive radiation beams afford longer detection range and finer spatial selectivity. Although conventionally used, patch antennas suffer from intrinsic path losses that are much higher when compared to the waveguide antenna. Designed at 77 GHz, presented in this article is an 8-element slot array on the narrow side wall of a rectangular waveguide, thus being readily extendable to planar arrays by adding others alongside while maintaining the element spacing requirement for grating lobe avoidance. Comprising tilted Z-shaped slots for higher gain while keeping constrained within the narrow wall, adjacent ones separated by half the guided wavelength are inclined with reversed tilt angles for cross-polar cancelation. An open-ended external waveguide is placed over each slot for polarization purification. Equivalent circuit models of slotted waveguides aid the design. An approach for sidelobe suppression using the Chebyshev distribution is adopted. Four types of arrays are proposed, all of which show potential for different demands and applications in automotive radar. Prototypes based on designs by simulations were fabricated and measured. Full article

In the detection of gravitational waves in space, during the science phase of the mission, the point-ahead angle mechanism (PAAM) serves to steer a laser beam to compensate for the angle generated by the relative motion of the two spacecrafts (SCs) during the approximately 10 s of flight time a laser beam will take from one SC to reach a distant SC of three million kilometers away. The Tilt-to-length (TTL) noise budget for the PAAM is constrained to less than $8 \mathrm{pm}/\sqrt{\mathrm{Hz}}$ within the frequency range of 1 mHz to 1 Hz. This constraint requires that the measurement noise of the interferometer remains below this threshold to guarantee the precision needed for gravitational wave detection in space. In the present work, an equal-arm heterodyne interferometer, which is fixed in a vacuum system with multilayer thermal shields, is proposed for the OPD (Optical Path Difference) measurement. The background measurement noise of the system is smaller than $60 \mathrm{pm}/\sqrt{\mathrm{Hz}}$ within the frequency range of 1 mHz to 1 Hz. This corresponds to an 84.6% noise reduction at 1 mHz compared to similar unshielded interferometers utilizing conventional bonding methods, demonstrating that the proposed system effectively suppresses measurement noises, particularly thermal noise, in the low-frequency range. Full article

Holographic detection technology has found extensive applications in biomedical imaging, surface profilometry, vibration monitoring, and defect inspection due to its unique phase detection capability. However, the accuracy of quantitative holographic phase imaging is significantly affected by the interference from direct current and twin image terms. Traditional methods, such as multi-exposure phase shifting and off-axis holography, have been employed to mitigate these interferences. While off-axis holography separates spectral components by introducing a tilted reference beam, it inevitably induces phase disturbances that compromise measurement accuracy. This study provides a computational explanation for the incomplete phase compensation issue in existing algorithms and establishes precision criteria for phase compensation based on theoretical formulations. We propose two novel phase compensation methods—the non-iterative compensation approach and the multi-iteration compensation technique. The principles and applicable conditions of these methods are thoroughly elucidated, and their superiority is demonstrated through comparative experiments. The results indicate that the proposed methods effectively compensate for phase disturbances induced by the tilted reference beam, offering enhanced precision and reliability in quantitative holographic phase measurements. Full article

A spatial light modulator (SLM) is a key element in several applications, but it is subject to surface deformation due to manufacturing imperfections or environmental factors. Therefore, the current study aims to analyze and compensate for such deformations in a phase-only SLM using a Michelson interferometer. The recorded interferogram represents the interference between the wavefront reflected from the SLM surface (object wave) and a reference wave. Noise in the recorded interferogram can degrade the accuracy of phase measurements. Various digital filtering techniques were applied to improve the signal-to-noise ratio (SNR) of the interferogram. The filtered interferogram enabled accurate phase extraction through Fourier transform processing and side peak selection using a spatial carrier frequency method. Additionally, phase errors caused by the tilt of the reference beam were corrected. Thereafter, the conjugate of the corrected phase distribution was used to calculate a phase-only computer-generated hologram (CGH), which was displayed on the SLM to compensate for surface deformations. The effectiveness of the proposed compensation procedure was confirmed by a second phase measurement, which demonstrated improved SLM performance. This study highlights the impact of combining the interferometric techniques with digital processing for precise surface deformation analysis. Full article

Low-frequency seismic vibrations extremely limit the performance of ground simulation facilities for space-borne gravitational wave detections, which need to be substantially suppressed. Active vibration systems are thus required. However, the tilt-translation coupling of inertial sensors strongly limits the performance of vibration isolation platforms in the low frequency range, which requires a precise measurement of the low-frequency tilt signal. This study compares two methods for the tilt signal measurement: the differential-mode method and the direct method. The differential-mode method estimates tilt signals by analyzing differential motion between two inertial sensors, while the direct method utilizes an interferometric tilt sensor (ITS) which consists of a suspended rotational beam system and an interferometer for the readout. Experimental results show that ITS achieves a lower noise floor. Its noise floor is dominated by the thermal-mechanical noise below 0.25 Hz and the readout noise of the interferometer above 0.25 Hz. The findings highlight the potential of ITS for improving the performance of vibration isolation platforms in the low-frequency range. Full article

Lasers with average powers of several kilowatts have become an important tool for industrial applications. Temporal and spatial beam shaping was demonstrated to improve existing and enable novel applications. A very promising technology for both highly dynamic beam shaping and power scaling is the coherent combining of the beams of an array of high-power fundamental mode fibers. However, the limited number of fibers allows only limited spatial resolution of the common phase front. It is therefore favorable to work with plane or spherical common phase fronts, which generate a “point”, i.e., a diffraction pattern with a strong main lobe in the focal plane. By applying a tilt to the common phase front, points can be positioned in the focal plane with high spatial resolution. The Civan DBL 6–14 kW investigated in this work allows switching between positions of the points with 80 MHz. Sequences of points can be used to create arbitrary shapes. The time constants of points and shapes are very critical for this type of shape generation. The current paper analyzes the relevant time constants for setting points and creating shapes and relates them to time constants in laser processes. This is mandatory to deterministically influence laser processes. Full article

An electromagnetic (EM) absorber-embedded Ka-band double-layer tapered slot antenna (DLTSA) is proposed in this work. The EM absorber is placed on both sides of the tapered radiating slots as a means of achieving the reduced monostatic radar cross section (RCS) at the X-band. A conventional tapered slot antenna (TSA) with EM absorbers at the same position suffers from the distorted current distribution from the feedline to the radiating slots and causes a degraded radiation performance with a tilted beam. In contrast, the DLTSA with EM absorbers maintains the impedance and radiation characteristics of the antenna without the EM absorbers, while achieving the reduced monostatic RCS for the cross-polarized incident wave. The functionality of the reduced RCS is verified with the 4-by-4 DLTSA array design. The 4-by-4 array prototype with FGM-125 EM absorbers is matched at the Ka-band with a 14.7 dBi boresight gain at 35 GHz. The monostatic RCS is measured in an indoor environment, showing 6.5 dB monostatic RCS reduction at the X-band on average, verifying the computed expectations. This work validates the possible use of EM absorbers at the front side of a missile seeker composed of end-fire radiating elements. Full article

In the calibration of cone-beam computed tomography (CBCT), two factors must be checked: the alignment of the imaging detector of the CBCT system and the effect of the slanted sample platform. Previously, we developed and validated a distinct procedure to accurately calibrate any misalignment of the detector by using a cylindrical phantom with beads in a straight line, parallel to the axis of rotation of the CBCT system. Here, we generalize our earlier procedure to calibrate the CBCT system while also detecting and rectifying a slight slant of the sample platform. We revise and validate our new procedure by calibrating the CBCT system, which also determines the tilt angle between the central axis of the phantom and the axis of rotation, when not 0°. The errors in misaligned angles for our new procedure are within ±0.03°, calibrating the CBCT system more precisely than our earlier work. To confirm this, we have performed a complete, precise calibration of a dental CBCT system with a tilting sample platform. We also reconstruct a HA phantom in this CBCT system to analyze the quality of reconstruction. We present here a validated method for calibrating a CBCT system and rectifying the effect of its tilting sample platform with good accuracy. Full article

Spatiotemporal optical vortices with arbitrary tilt angles can be generated by adjusting spatial chirp and beam size at a phase modulation plane in a pulse shaper setup. A grating pair setup is proposed to generate variable spatial chirp independent of the beam profile. The initial dispersion of the pulse allows for the independent control of the vortex orientation. By adjusting the beam size, spatial chirp, and initial dispersion, arbitrary vortex orientation across all the possible angles can be achieved. The ability to achieve arbitrary vortex orientations at long propagation distances could offer significant advantages for long-distance communication applications. Full article

As the global population grows, vertical farming offers a promising solution by using vertically stacked shelves in controlled environments to grow crops efficiently within urban areas. However, the shading effects of farm structures make artificial lighting a significant cost, accounting for approximately $67\%$ of total operational expenses. This study presents a novel approach to optimizing the deployment of laser illumination in rotating vertical farms by incorporating structural design, light modeling, and photosynthesis. By theoretically analyzing the beam pattern of laser diodes and the dynamics in the coverage area of rotating farm layers, we accurately characterize the light conditions on each vertical layer. Based on these insights, we introduce a new criterion, cumulative coverage, which accounts for both light intensity and coverage area. Then, an optimization framework is formulated, and a swarm intelligence algorithm, Differential Evolution (DE) is used to solve the optimization while considering the structural and operational constraints. It is found that tilting lights and placing them slightly off-center are more effective than traditional vertically aligned and center-aligned deployment. Our results show that the proposed strategy improves light coverage by $4\%$ compared to the intensity-only optimization approach, and by $10\%$ compared to empirical methods. This study establishes the first theoretical framework for designing energy-efficient artificial lighting deployment strategies, providing insights into enhancing the efficiency of vertical farming systems. Full article

Developing switchable and multifunctional metasurfaces is essential for high-integration photonics. However, most previous studies encountered challenges such as limited degrees of freedom, simple tuning of predefined functionality, and complicated control systems. Here, we develop a general strategy to construct switchable and multifunctional metasurfaces. Two spin-modulated wave-controls are enabled by the proposed high-efficiency metasurface, which is designed using both resonant and geometric phases. Furthermore, the switchable wavefront tailoring can also be achieved by flexibly altering the lattice constant and reforming the phase retardation of the metasurfaces based on the “rotating square” (RS) kirigami technique. As a proof of concept, a kirigami metasurface is designed that successfully demonstrates dynamic controls of three-channel beam steering. In addition, another kirigami metasurface is built for realizing tri-channel complex wavefront engineering, including straight beam focusing, tilted beam focusing, and anomalous reflection. By altering the polarization of input waves as well as transformation states, the functionality of the metadevice can be switched flexibly among three different channels. Microwave experiments show good agreement with full-wave simulations, clearly demonstrating the performance of the metadevices. This strategy exhibits advantages such as flexible control, low cost, and multiple and switchable functionalities, providing a new pathway for achieving switchable wavefront engineering. Full article