Search Results (522)

Bi₆Fe₂Ti₃O₁₈ (BFTO) ceramics were synthesized via a solid-state reaction route using stoichiometric amounts of Bi₂O₃, TiO₂, and Fe₂O₃ powders. A thermal analysis of the powder mixture was conducted to optimize the heat treatment parameters. Energy-dispersive X-ray spectroscopy (EDS) confirmed the conservation of the chemical composition following calcination. Final densification was achieved through hot pressing. The crystal structure of the sintered samples, examined via X-ray diffraction at room temperature, revealed a tetragonal symmetry for BFTO ceramics sintered at 850 °C. Electron backscatter diffraction (EBSD) provided detailed insight into the crystallographic orientation and microstructure. Broadband dielectric spectroscopy (BBDS) was employed to investigate the dielectric response of BFTO ceramics over a frequency range of 10 mHz to 10 MHz and a temperature range of −30 °C to +200 °C. The temperature dependence of the relative permittivity (ε_r) and dielectric loss tangent (tan δ) were measured within a frequency range of 100 kHz to 900 kHz and a temperature range of 25 °C to 570 °C. The impedance data obtained from the BBDS measurements were validated using the Kramers–Kronig test and modeled using the Kohlrausch–Williams–Watts (KWW) function. The stretching parameter (β) ranged from ~0.72 to 0.82 in the impedance formalism within the temperature range from 200 °C to 20 °C. Full article

TiAl alloy offers advantages including low density, high specific strength and stiffness, and excellent high-temperature creep resistance. It is widely used in the aerospace, automotive, and chemical sectors, as well as in other fields. However, at temperatures of 800 °C and above, it forms a porous oxide film predominantly composed of TiO₂, which fails to provide adequate protection. Applying high-temperature protective coatings is therefore essential. Oxides demonstrating protective efficacy at elevated temperatures include Al₂O₃, Cr₂O₃, and SiO₂. The Pilling–Bedworth Ratio (PBR)—defined as the ratio of the volume of the oxide formed to the volume of the metal consumed—serves as a critical criterion for assessing oxide film integrity. A PBR value greater than 1 but less than 2 indicates superior film integrity and enhanced oxidation resistance. Among common oxides, Al₂O₃ exhibits a PBR value within this optimal range (1−2), rendering aluminum-based compound coatings the most extensively utilized. Aluminum coatings can be applied via methods such as pack cementation, thermal spraying, and hot-dip aluminizing. Pack cementation, being the simplest to operate, is widely employed. In this study, a powder mixture with the composition Al:Al₂O₃:NH₄Cl:CeO₂ = 30:66:3:1 was used to aluminize γ-TiAl intermetallic compound specimens via pack cementation at 600 °C for 5 h. Subsequent isothermal oxidation at 900 °C for 20 h yielded an oxidation kinetic curve adhering to the parabolic rate law. This treatment significantly enhanced the high-temperature oxidation resistance of the γ-TiAl intermetallic compound, thereby broadening its potential application scenarios. Full article

The rising demand for sustainable protein is driving interest in insects as a raw material for advanced food ingredients. This review collates and critically analyses over 300 studies on the conversion of crickets, mealworms, black soldier flies, and other farmed species into powders, protein isolates, oils, and chitosan-rich fibers with targeted techno-functional roles. This survey maps how thermal pre-treatments, blanch–dry–mill routes, enzymatic hydrolysis, and isoelectric solubilization–precipitation preserve or enhance the water- and oil-holding capacity, emulsification, foaming, and gelation, while also mitigating off-flavors, allergenicity, and microbial risks. A meta-analysis shows insect flours can absorb up to 3.2 g of water g⁻¹, stabilize oil-in-water emulsions for 14 days at 4 °C, and form gels with 180 kPa strength, outperforming or matching eggs, soy, or whey in specific applications. Case studies demonstrate a successful incorporation at 5–15% into bakery, meat analogs and dairy alternatives without sensory penalties, and chitin-derived chitosan films extend the bread shelf life by three days. Comparative life-cycle data indicate 45–80% lower greenhouse gas emissions and land use than equivalent animal-derived ingredients. Collectively, the evidence positions insect-based ingredients as versatile, safe, and climate-smart tools to enhance food quality and sustainability, while outlining research gaps in allergen mitigation, consumer acceptance, and regulatory harmonization. Full article

Ceramic dental prosthetics with internal metal structures are made from a cobalt–chromium alloy that is coated with ceramic. This study aims to validate surface treatments for the metal that enhance the adhesion of the ceramic coating under masticatory forces. Surface conditioning is performed using mechanical methods, like sandblasting (SB), and thermal methods, such as oxidation (O). The ceramic coating is applied to the metal component following the conditioning process, which can be conducted using either a single method or a combination of methods. Each conditioned sample undergoes characterization through various techniques, including drop shape analysis (DSA), scanning electron microscopy (SEM), X-ray diffraction (EDX), and atomic force microscopy (AFM). After the ceramic coating is applied and subjected to thermal sintering, the metal–ceramic samples are mechanically tested to assess the adhesion of the ceramic layer. The research findings, illustrated by scanning electron microscopy (SEM) images of the metal structures’ surfaces, indicate that alloy powder particles ranging from 10 to 50 µm were either adhered to the surfaces or present as discrete dots. Particles that exceed the initial design specifications of the structure can be smoothed out using sandblasting or mechanical finishing techniques. The energy-dispersive spectroscopy (EDS) results show that, after sandblasting, fragments of aluminum oxide remain trapped on the surface of the metal structures. These remnants are considered impurities, which can negatively impact the adhesion of the ceramic to the metal substrate. The analysis focuses on the exfoliation of the ceramic material from the deformed metal surfaces. The results emphasize the significant role of the sandblasting method and the micro-topography it creates, as well as the importance of the oxidation temperature in the treatment process. Drawing on 25 years of experience in dental prosthetics and the findings from this study, this publication aims to serve as a guide for applying the ceramic bonding layer to metal surfaces and for conditioning methods. These practices are essential for enhancing the adhesion of ceramic materials to metal substrates. Full article

Aluminum and its alloy magnetron sputtering targets, owing to their superior electrical/thermal conductivity and robust substrate adhesion, serve as critical materials in advanced electronics and information technologies. It is known that the microstructure of the target, including grain uniformity and crystallographic texture, directly affects the sputtering performance and the quality of the deposited thin film. Despite extensive research efforts, the review paper focused on the microstructure of aluminum target materials is still absent. In that context, the recent progress on the Al alloy target is reviewed, focusing on grain refinement and texture control strategies. The roles of alloying elements, such as Si, Cu, and rare-earth Sc and Nd, are described first. The two conventional manufacturing techniques of fabricating Al targets, including melting and powder metallurgy, are introduced. Then, studies on grain refinement by thermomechanical processing routes (hot/cold rolling, annealing and forging) are summarized. Lastly, texture engineering through deformation and heat treatment protocols (unidirectional/multidirectional rolling, deformation thickness, and composite deformation modes) is reviewed. By establishing the relationship between thermomechanical processing and microstructure, this review provides insights for designing high-performance aluminum targets tailored to next-generation advanced thin-film applications. Full article

This study reports the discovery and structural characterization of a novel polymorph, designated as Form III, of Alclometasone dipropionate, a corticosteroid commonly used in the treatment of inflammatory dermatoses. Form III was obtained by modifying the crystallization conditions reported in prior art and was thoroughly characterized using Powder X-ray Diffraction (PXRD), Fourier Transform Infrared (FT-IR) spectroscopy, melting-point determination, Differential Scanning Calorimetry (DSC), Thermogravimetric Analysis (TGA), including its first derivative (DTG), optical microscopy, and Scanning Electron Microscopy (SEM). In parallel, pure Form II, previously observed only in mixtures with Form I, was successfully isolated and characterized using the same analytical techniques. Both forms were compared in terms of structural, thermal, and morphological properties. PXRD analysis revealed that Form III crystallizes in a triclinic system; FT-IR spectroscopy revealed unique vibrational signatures, and microscopy showed rod-like crystal morphology. The discovery of Form III expands the current understanding of the solid-state landscape of Alclometasone dipropionate and opens opportunities for the identification of new industrial purification methods for the compound. Full article

Thermally sprayed carbide cermet coatings, particularly those based on tungsten carbide (WC) and chromium carbide (Cr₃C₂) and produced with the high velocity oxygen fuel (HVOF) process, are used in tribological applications as environmentally friendly alternatives to electroplated hard chrome coatings. These functional coatings are especially prevalent in the automotive industry, offering excellent wear resistance. However, their mechanical and tribological performances are highly dependent on factors such as feedstock powders, spray parameters, and service conditions. This review aims to gain deeper insights into the above elements. It also outlines emerging advancements in HVOF technology—including in situ powder mixing, laser treatment, artificial intelligence integration, and the use of novel materials such as rare earth elements or transition metals—which can further enhance coating performance and broaden their applications to sectors such as the aerospace and hydro-machinery industries. Finally, this literature review focuses on process optimization and sustainability, including environmental and health impacts, critical material use, and operational limitations. It uses a life cycle assessment (LCA) as a tool for evaluating ecological performance and addresses current challenges such as exposure risks, process control constraints, and the push toward safer, more sustainable alternatives to traditional WC and Cr₃C₂ cermet coatings. Full article

This study investigated sustainable activation strategies for residual slag micro powder derived from recycled waste concrete aggregates, aiming to advance circular economy principles in construction materials. An experimental study was carried out to explore the activation mechanisms of slag micro powder from recycled waste concrete aggregates to enhance its utility in building materials. Three methods—mechanical grinding, high-temperature calcination, and mechanical grinding–thermal activation—were evaluated comparatively. The results showed high-temperature calcination at 750 °C for 10 min proved most effective, achieving a 95.85% activity index. High-temperature calcination may contribute to the release of active SiO₂ and Al₂O₃ substances of slag micro powder, thereby improving the hydration performance of slag micro powder and its cement mortar’s compressive strength. The flexural strength of cement mortar after different activation treatments was also analyzed. Mechanical grinding alone showed limited benefits, only achieving a less than 65.59% activity index, while the combined method negatively impacted the mechanical properties of cement mortar samples. An SEM (scanning electron microscope) and EDS (energy dispersive X-ray spectrometer) microstructural analysis supported these findings, highlighting enhanced hydration product formation after calcination at 750 °C for 10 min. This work may contribute to sustainable construction practices through the resource-efficient utilization of industrial by-products. Full article

This study developed sustainable biocomposites composed of polylactic acid (PLA) and surface-treated pineapple core powder (PACP), fabricated via extrusion and fused deposition modelling (FDM). PACP loadings of 1–3 vol% were combined after chemical modification with NaOH and silane to improve interfacial bonding. Particle morphology showed increased porosity and surface roughness following treatment. The melt flow index (MFI) increased from 31.56 to 35.59 g/10 min at 2 vol% PACP, showing improved flowability. Differential scanning calorimetry (DSC) showed the emergence of cold crystallization (T_cc ~121 °C) and an increase in crystallinity from 35.7% (neat PLA) to 47.3% (2 vol% PACP). Thermogravimetric analysis showed only slight decreases in T₅ and T_max, showing the thermal stability. The mechanical testing of extruded filaments showed increased modulus (1463 to 1518 MPa) but a decrease in tensile strength and elongation. For the 3D-printed samples, elongation at break increased slightly at 1–2 vol% PACP, likely because of the improvement in interlayer fusion. Though, at 3 vol% PACP, the mechanical properties declined, consistent with filler agglomeration observed in SEM. Overall, 2 vol% PACP offered the optimal balance between printability, crystallinity, and mechanical performance. These results reveal the possibility of PACP as a value-added biowaste filler for eco-friendly PLA composites suitable for extrusion and 3D printing applications. Full article

The development of effective, cost-efficient, and printable solid-state gas sensors for the detection of volatile organic compounds is of great interest due to their wide range of applications, spanning from real-time indoor monitoring to emerging fields such as non-invasive medical diagnostics. However, gas sensors encounter difficulties in discovering materials that have both good selectivity and sensitivity for numerous volatile organic compounds in both dry and humid settings. To expand the class of sensing materials, the current study investigates the sensing performance of solid solutions based on a rare-earth metal oxide. Pr, Fe, and Ti oxide solid solutions were produced using a solid-state technique, with thermal treatments at varied temperatures to tune their structural and functional properties. The powders were used, for the first time, to produce chemoresistive sensors, which showed promising sensing capabilities vs. ethanol, acetone, and acetaldehyde. The sensors were characterized by varying the concentration of the target gases from 1 to 50 ppm in a controlled environment, with the relative humidity ranging from 2 to 40%. The findings bring a turning point, leading to fruitful paths for the development of Pr-based solid solutions-based chemoresistive gas sensors for the detection of volatile organic compounds. Full article

Beryllium-based intermetallic compounds, such as Be₁₂Nb, are attracting growing interest for their high thermal stability and potential to replace pure beryllium as neutron reflectors and multipliers in both fission and future fusion reactors, with additional applications in metallurgy, aerospace, and hydrogen technology. The paper presents the results of an investigation of the thermal treatment and phase formation of the intermetallic compound Be₁₂Nb from a mixture of niobium and beryllium powders in the temperature range of 800–1300 °C. The phase evolution was assessed as a function of sintering temperature and time. A nearly single-phase Be₁₂Nb composition was achieved at 1100 °C, while decomposition into lower-order beryllides such as Be₁₇Nb₂ occurred at temperatures ≥1200 °C, indicating thermal instability of Be₁₂Nb under vacuum. Careful handling of sintering in low vacuum minimized oxidation, though signs of possible BeO formation were noted. The findings complement and extend earlier reports on Be₁₂Nb synthesis via plasma sintering, mechanical alloying, and other powder metallurgy routes, providing broader insight into phase formation and synthesis. These results provide a foundation for optimizing the manufacturing parameters required to produce homogeneous Be₁₂Nb-based components and billets at an industrial scale. Additionally, they help define the operational temperature limits necessary to preserve the material’s phase integrity during application. Full article

Lanthanum strontium manganate (La_1−xSr_xMnO₃) is considered a highly promising material for the development of intelligent thermal control coatings due to its exceptional properties. Recent studies on this material have primarily utilized solid-state synthesis as the main preparation method. Research efforts have predominantly focused on investigating the effects of material composition, heat treatment processes, and other factors on the properties of the synthesized material. There has been a limited amount of research investigating the influence of chemical precipitation process parameters on the properties of the synthesized La_1−xSr_xMnO₃ material. In this study, the intelligent thermal control coating material La_0.8Sr_0.2MnO₃ was synthesized using the chemical precipitation method. The effects of varying precipitant concentrations on the properties of the synthesized material were investigated. When the precipitant concentration is 12 wt.% or 15 wt.%, the synthesized powder agglomerates predominantly form three-dimensional blocky structures after sintering. At lower concentrations such as 6 wt.% and 9 wt.%, the powder agglomerates predominantly form two-dimensional sheet-like structures after sintering. At precipitant concentrations of 6 wt.% and 9 wt.%, the strontium content in the synthesized powder becomes significantly lower than the designed theoretical value. When the precipitant concentration is relatively high, localized manganese aggregation occurs in the synthesized lanthanum strontium manganate material. The temperature dependence of the emittance test result indicates that the emissivity variation of La_0.8Sr_0.2MnO₃ material synthesized using 12 wt.% ammonia solution as precipitant reaches 0.428 from 173 K to 373 K, demonstrating excellent emissivity modulation performance. Full article

Green soybeans, or edamame (Glycine max L. Merril), serve as a superior source of phytochemicals and other nutritive substances and are commonly used as ingredients and additives in food products due to their polyphenols’ functional properties and antioxidant activity. Hence, it is very important to use a process to extract compounds with functional roles from plants as efficiently as possible. In this study, we sought to identify the optimal conditions for extracting genistein, belonging to the aglycone subgroup of isoflavones, from edamame using the cold plasma (CP) and enzyme method. Additionally, the impact of various drying techniques (spray-drying and freeze-drying) and storage conditions on the crude genistein extract powder was evaluated. The findings showed that the maximum values for the total phenolic content (TPC), total flavonoid content (TFC), and genistein (22.5 ± 0.23 mg of gallic acid equivalents (GAE)/100 g; 15.3 ± 0.13 mg of catechin equivalents (CAE)/100 g; and 12.6 ± 0.10 mg/100 g, respectively) were achieved under optimal pretreatment conditions using a CP gas flow rate of 5 L/min for 30 min, followed by enzymatic treatment at a specific enzyme concentration of 2.0% (v/v) for 240 min of incubation. Moreover, a scanning electron microscopy (SEM) analysis demonstrated that the CP and enzyme treatment induced significant structural changes, as evidenced by the presence of deeper pores on the surface of the powder granules. Spray-drying demonstrated a superior efficacy compared to freeze-drying for encapsulating the crude isoflavone extract. This study’s results also demonstrated that storage at 4 °C significantly stabilized the TPC, TFC, and genistein content and the antioxidant activity while preserving the physical properties (solubility and color) of the crude extract powder for up to 45 days. In summary, cold plasma pretreatment and enzymatic treatments offer practical solutions by enhancing the efficiency of non-thermal extraction processes, thereby increasing the yield of bioactive compounds, maintaining quality, and diminishing reliance on traditional, harsh methods. The elevated genistein content in the crude extract powder indicates its prospective application as a functional ingredient in various food and nutraceutical contexts. Full article

Powders with phase composition including quasi-amorphous phases and calcium carbonate CaCO₃ in the form of calcite or aragonite and sodium halite NaCl as a reaction by-product were synthesized from 0.5M aqua solutions of sodium silicate and 0.5M aqua solutions of calcium and/or magnesium chlorides. Starting solutions were taken in quantities which could provide precipitation of hydrated calcium and/or magnesium silicates with molar ratios Ca/Si = 1 (CaSi), Mg/Si = 1 (MgSi) or (Ca+Mg)/Si = 1 (CaMgSi). Hydrated calcium and/or magnesium silicates, hydrated silica, magnesium carbonate, hydrated magnesium carbonate or hydrated magnesium silicate containing carbonate ions are suspected as components of quasi-amorphous phases presented in synthesized powders. Heat treatment of synthesized powders at 400, 600, 800 °C and pressed preceramic samples at 900, 1000, 1100 and 1200 °C were used for investigation of thermal evolution of the phase composition and microstructure of powders and ceramic samples. Mass loss of powder samples under investigation during heat treatment was provided due to evacuation of H₂O (m/z = 18), CO₂ (m/z = 44) and NaCl at temperatures above its melting point. After sintering at 1100 °C, the phase composition of ceramic samples included wollastonite CaSiO₃ (CaSi_1100); enstatite MgSiO₃, clinoenstatite MgSiO₃ and forsterite Mg₂SiO₄ (MgSi_1100); and diopside CaMgSi₂O₆ (CaMgSi_1100). After sintering at 1200 °C, the phase composition of ceramics CaSi_1200 included pseudo-wollastonite CaSiO₃. After heat treatment at 1300 °C, the phase composition of MgSi_1300 powder included preferably protoenstatite MgSiO₃. The phase composition of all samples after heat treatment belongs to the oxide system CaO–MgO–SiO₂. Ceramic materials in this system are of interest for use in different areas, including refractories, construction materials and biomaterials. Powders prepared in the present investigation, both via precipitation and via heat treatment, can be used for the creation of materials with specific properties and in model experiments as lunar regolith simulants. Full article

Cohesive soil in the reservoir area is vulnerable to natural disasters because of its poor erosion resistance and low strength. Therefore, it needs to be reinforced. Microbially induced calcium carbonate precipitation (MICP) is a sustaibable soil reinforcement technique with low energy consumption and no pollution. Different combinations of Bacillus subtilis bacterial solution (BS) concentrations and cementing solution (CS) concentrations were set to perform MICP solidification treatment. The characterization of cohesive soil before MICP was carried out by means of Scanning Electron Microscopy (SEM), Fourier-Transform Infrared Spectroscopy (FTIR), and Laser Particle Size Analyzer (LPSA). The results showed that the unreinforced soil showed an amorphous state with low strength and the particle size distribution was dominated by powder particles. However, with the addition of BS concentrations and CS concentrations, SEM results showed that spherical and rhombohedral minerals filled the pores of the cohesive soil, which increased the content of precipitations and enhanced the cementitious characteristics. When the concentrations of CS or BS were fixed, CaCO₃ content, deviatoric stress, shear strength, cohesive force, and internal friction angle all showed a trend of first increasing and then decreasing with the increase in CS or BS concentration. The optimal combination of CS and BS concentration was 1.5 mol/L and OD₆₀₀ = 1.8. Thermochemical analyses showed an improved thermal stability of the reinforcing cohesive soil, with the lowest mass loss (32%) and the highest pyrolysis temperature (812 °C) of the samples at the optimal combination of BS and CS concentration. This study is expected to improve the understanding of the MICP reinforcement process and contribute to the optimal design of future biologically mediated soil amendments, promoting bioremediation. Full article