Search Results (2,556)

The large-scale integration of renewable energy has significantly improved the low-carbon performance of power systems, but has also increased operational uncertainty. Under extreme weather conditions, wind and solar power may experience consecutive days of simultaneous output shortfalls—referred to as “renewable energy drought”—leading to persistently high net load and severe challenges to supply guarantee. To address this issue, this paper proposes a multi-source coordinated supply-guarantee dispatch strategy for consecutive-day renewable energy drought scenarios. First, net load is defined as the total system load minus the available wind and solar output. Based on magnitude and duration thresholds, renewable energy drought events are extracted from historical data to generate representative scarcity scenarios. Second, a multi-source coordinated optimization dispatch model is constructed, incorporating wind power, solar power, thermal units, battery energy storage, and pumped-storage hydro. The objective is to minimize the total system operating cost, which includes thermal fuel cost, start-up/shut-down costs, storage cycling cost, wind/solar curtailment penalty cost, and load shedding penalty cost. The load shedding penalty coefficient is set to a magnitude much higher than conventional costs to highlight the priority of supply guarantee. The model accounts for operational constraints such as minimum up/down times, deep regulation capability, ramping limits of thermal units, and charge/discharge power limits of storage. Taking a provincial power system in China for the year 2030 as a case study, a dispatch case covering four consecutive days (96 time periods) is designed. Based on a baseline scenario, eight groups of sensitivity analyses are conducted to comprehensively investigate the impacts of key factors on the supply-guarantee strategy, including: the minimum up/down time of thermal units, deep regulation capability, load shedding penalty cost, load level, rated energy capacity and charge/discharge efficiency of battery energy storage, rated energy capacity and pumping/generating efficiency of pumped-storage hydro, thermal fuel cost coefficient, and renewable energy capacity. Simulation results show that the proposed strategy can effectively coordinate multiple resources under consecutive-day drought conditions; reducing the minimum up/down time of thermal units improves supply flexibility but increases start-up/shut-down costs; enhancing deep regulation capability optimizes storage utilization and reduces total system cost; the load shedding penalty cost directly determines the trade-off between supply guarantee and economic efficiency; and as load level decreases by 5%, 10%, and 15%, the total system operating cost reduces by approximately 6.3%, 12.5%, and 18.8%, respectively. This study provides a quantitative method and technical support for supply-guarantee dispatch decisions and resource allocation in high-renewable power systems under persistent drought conditions. Full article

The increasing penetration of variable renewable energy sources (RESs) poses significant challenges to power system flexibility and reliability, particularly in systems with high solar generation. At the same time, existing Concentrating Solar Power (CSP) plants in Europe face declining economic viability due to high capital costs and the expiration of incentivized tariff schemes. This study proposes and evaluates a novel approach to repurpose CSP plants as flexible energy assets through the integration of cold thermal energy storage (CTES) within a Thermally Integrated Power-to-Heat-to-Power Energy Storage (TI-PTES) framework. The proposed system combines an ice/water-based cold storage with a CO₂-based refrigeration cycle to enhance the efficiency of the CSP steam cycle by reducing condenser temperatures, while also enabling temporal shifting of electricity consumption. A techno-economic optimization model based on PyPSA is developed to determine the optimal sizing and operation of the storage and refrigeration system under realistic load and electricity price conditions representative of the Spanish market. Results show that the integration of cold storage significantly alters system operation, shifting the chiller from a continuous demand-following mode to an intermittent, high-intensity regime. This leads to a reduction in annual operating expenditures by approximately 32% and an increase in annual profit and net present value (NPV), despite higher capital investment. While hourly net revenue becomes more volatile, with negative values during charging periods, cumulative annual performance improves due to effective temporal optimization. However, the absence of strong electricity price arbitrage and negative price signals limits the revenue potential of the storage system, which primarily acts as a cost-reduction mechanism. The findings demonstrate that cold thermal storage can successfully reposition CSP plants as flexible, value-generating assets in modern electricity systems. The proposed concept offers a promising pathway for extending the operational lifetime of existing CSP infrastructure while supporting higher integration of renewable energy sources. Full article

Thermal energy storage (TES) is essential for improving the flexibility and efficiency of renewable and industrial energy systems. This study experimentally compares sensible and latent heat storage using basalt aggregate and an encapsulated phase change material (PCM), specifically 60 wt.% NaNO₃–40 wt.% KNO₃, as packed-bed materials under elevated-temperature operating conditions. Tests were conducted in an air-based TES rig at air flow rates of 60–120 kg/h, with packed bed temperatures exceeding 400 °C. Key parameters included temperature profiles, thermal power, energy storage, and recovery during charging and discharging phases. The results indicate that increasing the air flow rate accelerated thermal front propagation and improved charging and discharging power, but did not proportionally increase stored or recovered energy. The basalt bed achieved recovered volumetric energy densities of 108–160 MJ/m³ at about 150 °C and 351–405 MJ/m³ above 320 °C. The encapsulated solar salt bed reached higher values, from 412–508 MJ/m³ near 290 °C to 523–626 MJ/m³ at higher temperatures. Both materials showed high TES efficiencies, in the range of 80–94%. Encapsulated PCM significantly increased energy storage density in packed-bed TES systems, while basalt aggregate provides higher short-term thermal power output. Full article

The sealing performance of compressed air energy storage (CAES) caverns represents a multi-physics challenge involving coupled thermal–hydraulic–mechanical processes, characterized by complex interacting factors. As a critical determinant of the long-term operational efficiency of CAES facilities, this study developed a fiber-reinforced cement-based composite sealing material through systematic orthogonal experiments investigating four key parameters: water–cement ratio, sand ratio, fly ash–silica fume content, and basalt fiber content. An optimized mixture was formulated with a water–cement ratio (0.36), sand ratio (42%), fly ash–silica fume content (22%), and basalt fiber content (1.0%). Under this optimal mix proportion, the measured permeability coefficient of the sealing layer is 1.92 × 10⁻¹³ cm/s, and the uniaxial compressive strength and tensile strength are 37 MPa and 3.9 MPa, respectively, with a corresponding elastic modulus of 18 GPa. Meanwhile, the P-wave velocity is approximately 2823 m/s, and the porosity is 0.15, achieving balanced performance in permeability, strength, and porosity. The material was validated in a CAES physical model through gas charge–discharge tests under various operational scenarios for the composite sealing layer-lining-surrounding rock system. Full article

To alleviate grid peak-shaving pressure from high-penetration renewable energy integration, coupling thermal energy storage (TES) with coal-fired power plants is an effective approach for enhancing operational flexibility. This paper systematically investigates the peak-shaving performance of a coal-fired unit integrated with molten salt storage and heat pump storage systems, focusing on load response characteristics, peak-shaving capability, and the influence of discharge strategies on thermodynamic performance under various rated turbine heat acceptance (THA) conditions. The results indicate that, under identical peak-shaving capacity, the molten salt system exhibits greater storage capacity, which increases with rising THA levels, whereas the heat pump storage capacity remains largely THA-independent. Regarding discharge strategies, replacing high-pressure extraction steam achieves the fastest ramp rate and largest incremental power output, introducing steam into the intermediate-pressure cylinder yields the slowest response but highest round-trip efficiency, and replacing low-pressure extraction steam delivers the smallest peak-shaving capacity and lowest round-trip efficiency. Although TES integration slightly reduces thermal efficiency due to heat exchange losses, this trade-off is justified by significant flexibility improvement, demonstrating clear engineering value for high-renewable grids. Full article

This study presents a comparative evaluation of geopolymer foams incorporating either commercially available shape-stabilized phase change materials (PCMs) or laboratory-developed diatomite–paraffin PCM granules with controlled particle size fractions ranging from <1.6 mm to >2.5 mm. All PCM variants were incorporated at a constant dosage of 7.5 wt.% to isolate the influence of PCM type on the properties of the resulting composites. The commercial materials comprised PX-4, PX15, and PX20 (Rubitherm Technologies GmbH), whereas the laboratory-developed PCM consisted of paraffin immobilized within a porous diatomite matrix to produce granular shape-stabilized composites. The experimental program included the determination of bulk density, total porosity, pore size distribution, thermal conductivity (λ), thermal resistance (R), specific heat capacity (Cp), and compressive strength. The pore structure was characterized by mercury intrusion porosimetry (MIP), while the morphology and dispersion of PCM particles within the geopolymer matrix were investigated using scanning electron microscopy (SEM). All mixtures were produced using the same alkali-activated matrix and identical curing conditions, with the PCM content maintained at 7.5 wt.%. The results demonstrated that the type of PCM significantly affected the microstructure and thermophysical performance of the geopolymer foams. The laboratory-developed diatomite–paraffin PCM provided the most favorable thermal insulation performance, exhibiting the lowest thermal conductivity (0.095 W/m·K) together with the highest thermal resistance (0.278 m²·K/W). In contrast, the commercial PX15 and PX20 materials exhibited the highest specific heat capacities (1.740 and 1.778 kJ/kg·K, respectively), indicating superior thermal energy storage capability. In addition, the estimated production cost of the laboratory-developed PCM (2.5–4.0 EUR/kg) was substantially lower than that of the commercial PX materials (approximately 20 EUR/kg), highlighting its potential as a cost-effective alternative for sustainable, energy-efficient building materials. These findings demonstrate that both commercial and laboratory-developed PCM systems can effectively enhance the functionality of geopolymer foams, although they provide different balances between thermal insulation, heat storage capacity, and production cost. Full article

With the rapid development of commercial aerospace, emerging applications such as satellite constellations, space-based communications, and orbital computing platforms have significantly increased the demand for efficient and reliable spacecraft power systems. Abundant exploitable energy exists in the space environment, including Air Mass Zero (AM0) solar radiation, spacecraft surface temperature gradients, ambient electromagnetic radiation, and radioisotope thermal energy, making multi-source energy harvesting a promising approach for improving satellite energy autonomy and system redundancy. This paper reviews the following four key space energy harvesting technologies: photovoltaic power generation, radio frequency (RF) energy harvesting, thermoelectric energy harvesting, and radioisotope thermoelectric generators (RTGs). The impacts of harsh space environmental factors on device performance and reliability are analyzed, and the applicability of different technologies in low Earth orbit (LEO), geostationary orbit (GEO), and deep-space missions is discussed. Furthermore, a multi-source self-powered satellite energy architecture integrating energy harvesting, energy storage, and power management is proposed. Finally, the major challenges and future development trends of satellite energy harvesting systems are summarized. Full article

This review shows that lignocellulosic biomass is not merely an abundant feedstock for nanocellulose production but a strategic platform for building the next generation of sustainable, high-performance materials, integrating feedstock diversity, processing logic, characterization, market direction, and translational applications into a single narrative. Comparing woody and non-woody biomass through the lens of processability, recalcitrance, and value creation while showing why agricultural residues are increasingly central to low-cost, circular nanocellulose production beyond the usual acid-hydrolysis-centered discussion by emphasizing enzymatic hydrolysis as a lower-energy, lower-toxicity alternative while still acknowledging the persistent industrial advantages and environmental costs of chemical and mechanical routes. A further strength of this review is its effort to bridge structure and function: it links extraction strategy to morphology, crystallinity, thermal stability, and surface chemistry, then connects these properties to real applications in packaging, drug delivery, electronics, filtration, energy storage, and biomedical systems. Its distinctive contribution lies in showing that the future of nanocellulose depends not only on how it is extracted but also on how intelligently the biomass source, processing route, material performance, and market need are aligned. Full article

To explore the optimized operating strategies coupling floor cooling with cold storage for thermal active systems (TABSs), effects of operating time on indoor thermal environment, cold storage capacity, energy use and running cost were studied. Simulations were conducted based on an actual office building equipped with floor cooling. To take full advantage of the TABS and off−peak electricity, four operating cases with nighttime floor cold storage were proposed, namely C₁ (2:00–8:00), which operated only during the off−peak hours, C₂ (2:00–10:00), C₃ (2:00–12:00), and C₄ (2:00–14:00), which operated during the off−peak and flat hours. A simulation case of C₀ operating during daytime (7:00–17:00) was also proposed. Simulation results show that the C₁ and C₂ conditions with shorter operating hours result in higher indoor temperatures, which cannot ensure indoor thermal comfort. The PMV index in C₃ and C₄ conditions can be kept between −1 and 1, which meets the thermal comfort demand of Grade II. Considering that the operating duration of C₃ is the same as the occupied hours, the cold storage capacity, cooling loss, cooling supply and release process, etc., of this case are further analyzed based on data of a typical day. The floor and ceiling slabs store most of the cooling energy (72.7%) during the night; inner walls also store part of the cooling energy (23.3%) and cooling loss during cold storage accounts for approximately 3.1%. During working hours, the cooling energy released is lower than the cooling load, which makes indoor temperatures increase continuously. Compared with case C₀, case C₃ has same power use while saving 2.8% of running costs. Case C₄ provides a higher level of thermal comfort, while saving 0.9% of costs with a 1.5% increment in electricity use. This study provides detailed data about cold storage strategies coupling with floor cooling in TABS, which can be used to save running cost. Full article

Under the background of the green transformation and energy conservation in the aviation field, hydrogen-fueled aero-engines are the primary direction for achieving sustainable aviation power development. However, the unique thermophysical properties of hydrogen fuel induce extreme thermal load challenges to engine thermal management. Based on the requirements of energy conservation and digital-intelligent technologies, this paper reviewed the recent research progress, important challenges, and future development directions in the thermal management field for hydrogen-fueled aero-engines, and filled the gaps in existing related reviews. (1) As for the liquid hydrogen thermal properties and thermal management requirements, the unique thermal physical properties of liquid hydrogen can easily cause fluctuations in heat load, large temperature differences, and material compatibility issues such as hydrogen embrittlement during storage, transportation, and combustion. The application of thermal barrier coatings, the design of targeted cooling structures, and the regulation of heat loss in the pipeline of the hydrogen supply system require particular attention. (2) As for the technical architecture and optimization of thermal management, the optimization of the high-pressure side manifolds in the cooled cooling air heat exchanger increases the flow uniformity by 18.8% and reduces the weight by 22.5%. The intercooled recuperated engine with the optimum area ratio reduces specific fuel consumption by 5.3% compared to the baseline engine in cruise. However, the system-level optimization research of the above widely recognized solutions is relatively limited in terms of coordinating the energy flow of engines. The baseline engine employed the method of system integration optimization to achieve a 2.99% increase in thrust and a 6.78% reduction in fuel consumption. (3) As for the thermal management modeling and simulation, the intelligent optimization method based on computational fluid dynamics reduces the pressure loss coefficient of the vane-integrated heat exchanger by 36%. Nevertheless, the multiphysics coupling model confronts a contradiction between computational cost and accuracy. (4) As for the comprehensive evaluation method, the advanced configuration of the hydrogen-fueled aero-engine can approximately reduce specific fuel consumption by 68.5% and NOx emission by 12.7% under the same maximum thrust condition. The hydrogen consumption of the proton exchange membrane fuel cells system model compared with the baseline system, optimized by the multi-objective optimization algorithm, has decreased by 15%, while the thermal uniformity has improved by 20–30%. However, the current evaluation system mostly focuses on a single dimension, lacking the analysis of nonlinear coupling among multiple factors and a closed-loop mechanism for evaluation, optimization, and verification. Future research should focus on the matching model of liquid hydrogen’s thermophysical properties and full flight conditions, global multi-energy flows optimization methods, multidimensional collaborative numerical simulation, multiphysics coupling models, and multidimensional comprehensive evaluation systems, to provide closed-loop theoretical support for the efficient, intelligent, and reliable thermal management system for hydrogen-fueled aero-engines. Full article

This study presents the design and modeling of a first-of-its-kind experimental prototype integrating a high-temperature air-based Concentrated Solar Power (CSP) receiver with a diabatic Compressed Air Energy Storage (CAES) system. The prototype architecture and operating modes are defined, and a detailed thermal model of an Open Volumetric Air Receiver (OVAR) is developed and optimized, with emphasis on passive mass flow regulation under non-uniform solar flux. At nominal conditions (800 °C), the receiver achieves a predicted thermal efficiency of 81.6%. Transient simulations assess off-design dynamic behavior under realistic conditions, showing sensitivity to solar fluctuations and need for heliostat aiming strategies to reduce thermal non-uniformities and ensure stable outlet temperatures. For the CAES subsystem, a techno-economic analysis identifies high-pressure (300 bar) commercial gas cylinders as the most cost-effective aboveground storage solution, while discharge simulations yield a required storage volume of 4.8 m³. Finally, the complete piping and instrumentation diagram (P&ID) of the integrated system is presented, defining the experimental configuration. Overall, this work establishes the design basis for the future experimental demonstration of hybrid CAES-CSP operation for dispatchable renewable power generation and supports subsequent control development and scale-up analyses. Full article

Wastewater treatment plants (WWTPs) can serve as hubs for converting waste into energy, thereby supporting a city’s energy needs. Thermal processes, especially gasification, enable the transformation of sewage sludge into valuable products by producing energy-rich syngas for electricity generation. However, conventional air-based gasification introduces nitrogen as a diluent, reducing the syngas energy density. Integrating electrolyzers for hydrogen production into WWTP operations offers a strategic advantage: the oxygen co-produced during water electrolysis can be utilized as a gasification agent, thereby minimizing nitrogen dilution and enhancing syngas quality. The present work assesses the simulation of a conventional WWTP integrated with gasification and electrolysis systems using Superpro Designer V13. The results demonstrate that using pure oxygen in the gasification unit reduces the process’s thermal energy requirements and increases the syngas energy content by 5.5% when operating in a CO₂ atmosphere at an equivalence ratio (ER) of 0.15. The integration of anaerobic digestion and sludge gasification improves the overall energy balance by increasing electrical output (67%) and enabling thermal energy recovery, allowing sludge drying without auxiliary fuel. Water electrolysis is integrated as an energy storage system, allowing flexible operation during periods of excess renewable electricity. However, a simplified balance of this strategy reveals negative economic results unless electricity prices are below 7.5 c€/kwh. This approach underscores the need for further research into the use of reclaimed water for hydrogen production, as well as improving process integration to reduce the energy and water footprints of technologies supporting the green transition. Full article

Driven by the global low-carbon transition and the rapid expansion of marine energy development, offshore integrated energy systems are emerging as a critical configuration for coupling offshore renewable resources, geothermal and subsurface thermal resources, oil and gas infrastructure, hydrogen pathways, multi-carrier networks, and offshore loads. Unlike onshore integrated energy systems, offshore systems are constrained by resource intermittency, harsh marine environments, platform space and weight limits, long-distance transmission, operation and maintenance accessibility, safety risks, and cross-regional governance mechanisms. Recent studies have advanced offshore wind-to-hydrogen systems, oil and gas platform electrification, offshore energy hubs, platform repurposing, and offshore geothermal utilization. However, these studies remain fragmented in terms of system boundaries, multi-energy coupling mechanisms, engineering constraints, and optimization methods. This paper reviews offshore integrated energy systems from the perspectives of system configuration, key integration technologies, optimization and assessment methods, and future research needs. Offshore integrated energy systems are first classified into offshore renewable-energy-dominated systems, offshore wind–hydrogen systems, oil and gas platform integrated systems, offshore energy hubs and multi-carrier networks, decommissioned-platform repurposing systems, and offshore geothermal and repurposed-well systems. Resource-side, conversion-side, storage-side, network-side, and load-side integration technologies are then summarized. Capacity configuration, operational scheduling, stochastic and robust optimization, multi-objective optimization, energy, exergy, economic, and environmental (4E) assessment, advanced exergy analysis, and energy-hub modelling are further reviewed. Finally, key research gaps are identified, including resource uncertainty, offshore engineering constraints, multi-carrier network coupling, insufficient demonstration data, and policy and economic uncertainty. This review provides a structured reference for the modelling, integration, optimization, and demonstration of offshore integrated energy systems for low-carbon transition. Full article

In the context of the global transition towards energy systems with a high share of renewable energy, efficient and large-scale energy storage technologies are essential for improving the stability and flexibility of power grids. Phase change thermal energy storage has attracted considerable attention because of its high energy density and nearly isothermal heat release capability. However, its practical application remains constrained by the intrinsically low thermal conductivity of phase change materials (PCMs). For instance, 0.2–0.3 W/m·K for organic paraffins, 0.15–0.35 W/m·K for fatty acids, and 0.5–1.0 W/m·K for salt hydrates lead to slow charging and discharging rates. Incorporating metal foams into PCMs to form composite PCMs has emerged as a promising strategy, as metal foams can significantly improve effective thermal conductivity and enhance internal heat transfer. This paper systematically reviews recent advances in metal foam-enhanced phase change thermal energy storage, with particular emphasis on numerical modeling and structural optimization. First, the heat transfer enhancement mechanisms of metal foam/PCM composites are analyzed, together with the key performance indicators used to evaluate thermal storage performance. Second, material-level developments are reviewed, including pore structure parameters, interfacial engineering, and advanced fabrication methods. The review then discusses current structural design strategies, such as graded pore structures and partially filled configurations, as well as hybrid enhancement methods that combine passive and active heat transfer enhancement. Particular attention is paid to numerical modeling approaches at both pore and system scales, which are used to predict and optimize thermal behavior. In addition, optimization methods, including topology optimization, machine learning, and genetic algorithms, are examined for their potential to inversely design foam structures with tailored thermal performance. Finally, the key challenges in this field are summarized, and future research directions are proposed. These include multi-scale intelligent design, integration with complementary thermal management technologies, and the development of scalable solutions for engineering applications. This review aims to provide a systematic reference for achieving performance breakthroughs and promoting the practical deployment of phase change thermal energy storage technologies. Full article

Proton-exchange-membrane reversible fuel cells (rPEM) are emerging as key technologies for integrated hydrogen-based energy storage systems, enabling both electricity generation and hydrogen production within a single electrochemical device. However, the transition from laboratory-scale characterization to system-level deployment requires a consistent framework linking electrochemical modeling, parameter calibration, and system design. In this work, a semi-empirical electrochemical model of an rPEM cell is developed and calibrated against literature experimental data in both fuel cell (FC) and water electrolysis (WE) modes. The calibrated model achieves high predictive accuracy, with coefficients of determination exceeding 0.997. The validated model is subsequently extended to a preliminary system-level design, enabling the development of a 100 kW reversible PEM system coupled with a 300 kW electrolyzer configuration. The proposed system features symmetric hydrogen flow (6 kg h⁻¹), a 200 kWh hydrogen storage buffer, and operating conditions of 2.5 bar/70 °C in FC mode and 30 bar/65 °C in WE mode. Thermal effects and efficiency trends are analyzed, highlighting the critical role of heat management and balance of plant proposed design. The proposed methodology provides a consistent framework for scaling rPEM technology toward industrial applications. Full article