Search Results (18)

Distributed fiber-optic sensing (DFOS) with intentionally spaced mechanical fixity points was experimentally evaluated for the structural health monitoring (SHM) of reinforced concrete (RC) members. A full-scale four-point bending test was conducted on a 12 m RC beam (400 × 400 mm) instrumented with a single-mode DFOS cable incorporating internal anchors at 2 m intervals and bonded externally with structural epoxy. Brillouin time-domain analysis (BOTDA) provided distributed strain measurements at approximately 0.5 m spatial resolution, with all cables calibrated to ±15,000 µε. Under stepwise monotonic loading, the system captured smooth, repeatable strain baselines and clearly resolved localized tensile peaks associated with crack initiation and propagation. Long-gauge averages exhibited a near-linear load–strain response (R² ≈ 0.99) consistent with discrete foil and vibrating-wire strain gauges. Even after cracking, the DFOS signal remained continuous, while some discrete sensors showed saturation or scatter. Temperature compensation via a parallel fiber ensured thermally stable interpretation during load holds. The fixed-point configuration mitigated local debonding effects and yielded unbiased long-gauge strain data suitable for assessing serviceability and differential settlement. Overall, the results confirm the suitability of fixed-point DFOS as a durable, SHM-ready sensing approach for RC foundation elements and as a dense data source for emerging digital-twin frameworks. Full article

Biodegradable and bio-based polymers, such as starch and gelatin, are emerging as an important alternative to the use of conventional polymers. In this work, different proportions (1/1, 1/1.5, 1/2, and 1/2.5) of these bio-based polymers will be investigated, with the primary objective of considering their strong moisture dependence as an advantage instead of a problem, as commonly considered. For this interesting challenge, the humidity-activated shape memory effect has been studied in both neat and plasticized starch. Additionally, for the first time, to the best of our knowledge, the shape-memory behavior activated by humidity in gelatin, as well as in starch/gelatin blends, is reported. In all cases, starch, gelatin, and their plasticized blends show excellent values in terms of strain fixity ratio, obtaining values of about 100% in all cases, and strain recovery ratio, with values higher than 90% for the samples studied. Moreover, considering their potential application as food packaging, mechanical response, wettability, water permeability, water uptake rate, and roughness is also studied in this work, taking into account the effect of the different amounts of gelatin on the final behavior of the materials. Full article

Poly(lactic acid) (PLA) exhibits excellent shape memory properties but suffers from brittleness and a high glass transition temperature (T_g), limiting its utility in flexible and durable applications. This study explored the modification of PLA properties through the incorporation of poly(ethylene glycol) (PEG), varying in both content (5–20 wt%) and molecular weight (4000–12,000 g/mol), to enhance its suitability for specific applications, such as medical splints. The PLA/PEG blend, containing 15 wt% PEG and with a molecular weight of 12,000 g/mol, exhibited superior shape fixity (99.27%) and recovery (95.77%) in shape memory tests conducted at a programming temperature (T_p) of 45 °C and a recovery temperature (T_r) of 60 °C. Differential scanning calorimetry (DSC) analysis provided insights into the thermal mechanisms driving shape memory behavior of the PLA/PEG blend. The addition of PEG to the PLA blend resulted in a reduction in T_g and an increase in crystallinity, thereby facilitating enhanced chain mobility and structural reorganization. These thermal changes enhanced the shape fixity and recovery of the PLA/PEG blend. Synchrotron wide-angle X-ray scattering (WAXS) was further employed to elucidate the microstructural evolution of PLA/PEG blends during the shape memory process. Upon stretching, the PLA/PEG chains aligned predominantly along the tensile direction, reflecting strain-induced orientation. During recovery, the PLA/PEG chains underwent isotropic relaxation, reorganizing into their original configurations. This structural reorganization highlighted the critical role of chain mobility and alignment in driving the shape memory behavior of PLA/PEG blends, enabling them to effectively return to their initial shape. Mechanical testing confirmed that increasing PEG content and molecular weight enhanced elongation at break and impact strength, balancing flexibility and strength. These findings demonstrated that PLA/PEG blends, especially with 15 wt% PEG at 12,000 g/mol, offer an optimal combination of shape memory performance and mechanical properties, positioning them as promising candidates for customizable and biodegradable medical applications. Full article

In four-dimensional additive manufacturing (4DAM), specific external stimuli are applied in conjunction with additive manufacturing technologies. This combination allows the development of tailored stimuli-responsive properties in various materials, structures, or components. For shape-changing functionalities, the programming step plays a crucial role in recovery after exposure to a stimulus. Furthermore, precise tuning of the 4DAM process parameters is essential to achieve shape-change specifications. Within this context, this study investigated how the structural arrangement of infill patterns (criss-cross and concentric) affects the shape memory effect (SME) of compression cold-programmed PLA under a thermal stimulus. The stress–strain curves reveal a higher yield stress for the criss-cross infill pattern. Interestingly, the shape recovery ratio shows a similar trend across both patterns at different displacements with shallower slopes compared to a higher shape fixity ratio. This suggests that the infill pattern primarily affects the mechanical strength (yield stress) and not the recovery. Finally, the recovery force increases proportionally with displacement. These findings suggest a consistent SME under the explored interval (15–45% compression) despite the infill pattern; however, the variations in the mechanical properties shown by the stress–strain curves appear more pronounced, particularly the yield stress. Full article

In situ-generated nanofibrillar polymer–polymer composites are excellent candidates for the production of polymer materials, with high mechanical and SME properties. Their special feature is the high degree of dispersion of the in situ-generated nanofibers and the ability to form entangled nanofiber structures with high aspect ratios through an end-to-end coalescence process, which makes it possible to effectively reinforce the polymer matrix and, in many cases, increase its ductility. The substantial interfacial area, created by the in situ formed fiber/matrix morphology, significantly strengthens the interfacial interactions, which are crucial for shape fixation and shape recovery. Using the polylactide/bio-polyamide (PLA/PA) system as an example, it is shown that in situ PA fibrillation improves the mechanical and shape-memory properties of PLA. The modulus of elasticity increases by a factor of 1.4, the elongation at break increases by a factor of 30, and the shape-strain/fixity ratio and shape recovery increase from 80.2 to 97.4% and from 15.5 to 94.0%, respectively. The morphology of the minor PA phase is crucial. The best result is achieved when a physically entangled nanofibrous network is formed. Full article

This paper investigates the impact of halloysite nanotube (HNT) content on mechanical and shape memory properties of additively manufactured polyurethane (PU)/HNT nanocomposites. The inclusion of 8 wt% HNTs increases their tensile strength by 30.4% when compared with that of virgin PU at 44.75 MPa. Furthermore, consistently significant increases in tensile modulus, compressive strength and modulus, as well as specific energy absorption are also manifested by 47.2%, 34.0%, 125% and 72.7% relative to neat PU at 2.29 GPa, 3.88 MPa, 0.28 GPa and 0.44 kJ/kg respectively. However, increasing HNT content reduces lateral strain due to the restricted mobility of polymeric chains, leading to a decrease in negative Poisson’s ratio (NPR). As such, shape recovery ratio and time of PU/HNT nanocomposites are reduced by 9 and 45% with the inclusion of 10 wt% HNTs despite an increasing shape fixity ratio up to 12% relative to those of neat PU. Full article

Melt electrowriting is a relatively new additive manufacturing technique capable of the controlled deposition of polymeric fibers to manufacture pre-programmed structures at micron scale. In this research, a blend of poly (ε-caprolactone) and thermoplastic urethane displaying shape memory properties is processed using melt electrowriting. The bulk material at macro scale shows a transition temperature of around 60 °C. Fibers with diameter less than 60 µm were deposited as sinusoids and grid-like scaffolds. A high strain fixity ratio of 92% was obtained for the polymer, which is in accordance with the literature on shape memory polymers. These shape memory structures can be used for applications such as micro-sensing and actuating. Full article

Thermoresponsive shape memory polymers (SMPs) with the remarkable ability to remember a temporary shape and recover their original one using temperature have been gaining more and more attention in a wide range of applications. Traditionally, SMPs are investigated using a method named often “hot-programming”, since they are heated above their glass transition temperature (T_g) and after that, reshaped and cooled below T_g to achieve and fix the desired configuration. Upon reheating, these materials return to their original shape. However, the heating of SMPs above their T_g during a thermomechanical cycle to trigger a change in their shape creates a temperature gradient within the material structure and causes significant thermal expansion of the polymer sample resulting in a reduction in its shape recovery property. These phenomena, in turn, limit the application fields of SMPs, in which fast actuation, dimensional stability and low thermal expansion coefficient are crucial. This paper aims at a comprehensive experimental investigation of thermoplastic polyurethane shape memory polymer (PU-SMP) using the cold programming approach, in which the deformation of the SMP into the programmed shape is conducted at temperatures below T_g. The PU-SMP glass transition temperature equals approximately 65 °C. Structural, mechanical and thermomechanical characterization was performed, and the results on the identification of functional properties of PU-SMPs in quite a large strain range beyond yield limit were obtained. The average shape fixity ratio of the PU-SMP at room temperature programming was found to be approximately 90%, while the average shape fixity ratio at 45 °C (T_g − 20 °C) was approximately 97%. Whereas, the average shape recovery ratio was 93% at room temperature programming and it was equal to approximately 90% at 45 °C. However, the results obtained using the traditional method, the so-called hot programming at 65 °C, indicate a higher shape fixity value of 98%, but a lower shape recovery of 90%. Thus, the obtained results confirmed good shape memory properties of the PU-SMPs at a large strain range at various temperatures. Furthermore, the experiments conducted at both temperatures below T_g demonstrated that cold programming can be successfully applied to PU-SMPs with a relatively high T_g. Knowledge of the PU-SMP shape memory and shape fixity properties, estimated without risk of material degradation, caused by heating above T_g, makes them attractive for various applications, e.g., in electronic components, aircraft or aerospace structures. Full article

Low-melting-point alloy (LMPA) was used as an additive to prepare epoxy-resin-based shape memory polymer composites (LMPA/EP SMP), and dynamic mechanical analyzer (DMA) tests were performed to demonstrate the shape memory effect, storage modulus, and stiffness of the composites under different load cases. The composites exhibited an excellent shape recovery ratio and shape fixity ratio, and a typical turning point was observed in the storage modulus curves, which was attributed to the melting of the LMPA. In order to investigate the dynamic deformation mechanism at high strain rates, split Hopkinson pressure bar (SHPB) experiments were performed to study the influence of the strain rate and plastic work on the dynamic mechanical response of LMPA/EP composites. The results showed that there was a saturated tendency for the flow stress with increasing strain rate, and the composites exhibited a typical brittle failure mode at high strain rate. Moreover, an obvious melting phenomenon of the LMPA was observed by SEM tests, which was due to the heat generated by the plastic work at high strain rate. The fundamental of the paper provided an effective approach to modulate the stiffness and evaluate the characteristics of SMP composites. Full article

In this work, the thermally-activated shape memory behavior of poly(lactic acid)-based electrospun fibers (PLA-based efibers) reinforced with different amounts of magnesium oxide (MgO) nanoparticles (NPs) was studied at different temperatures. In particular, MgO NPs were added at different concentrations, such as 0.1, 0.5, 1 and 3 wt%, with respect to the PLA matrix. The glass-transition temperature of PLA-based efibers was modulated by adding a 20 wt% of oligomer lactic acid as plasticizer. Once the plasticized PLA-based efibers were obtained and basically characterized in term of morphology as well as thermal and mechanical properties, thermo-mechanical cycles were carried out at 60 °C and 45 °C in order to study their thermally-activated shape memory response, demonstrating that their crystalline nature strongly affects their shape memory behavior. Importantly, we found that the plastificant effect in the mechanical response of the reinforced plasticized PLA efibers is balanced with the reinforcing effect of the MgO NPs, obtaining the same mechanical response of neat PLA fibers. Finally, both the strain recovery and strain fixity ratios of each of the plasticized PLA-based efibers were calculated, obtaining excellent thermally-activated shape memory response at 45 °C, demonstrating that 1 wt% MgO nanoparticles was the best concentration for the plasticized system. Full article

Shape memory polymer composites (SMPCs) have been manufactured by press moulding of carbon fibre-reinforced (CFR) prepregs with SMP interlayers. SMPC laminates have been produced with different numbers of CFR plies (i.e., 2, 4, 6, and 8) and different thicknesses of the SMP interlayers (i.e., 100 and 300 µm) for a sum of eight combinations. Co-curing of the prepreg plies and the SMP interlayers has led to an optimal adhesion of structural and functional plies, which has been confirmed by following testing. Single thermo-mechanical cycles at increasing strains (i.e., 0.06%, 0.12%, and 0.18%) and multiple cycling have been performed to test SMPC laminate durability. Delamination and fibre cracking were not observed during testing, and laminates showed a reproducible SM behaviour after 10 consecutive thermo-mechanical cycles. SM properties have been extracted from tests in terms of residual and memory loads as well as shape fixity and shape recovery. These data may be used for comparison of the performances of the different laminates, and as a first base for designing SMPC structures. Thin laminates exhibit lower recovery loads but higher shape fixity than thick ones, but the shape recovery is very high for all the SMPCs, with an average of 98%. Full article

The ever-increasing demand for materials to have superior properties and satisfy functions in the field of soft robotics and beyond has resulted in the advent of the new field of four-dimensional (4D) printing. The ability of these materials to respond to various stimuli inspires novel applications and opens several research possibilities. In this work, we report on the 4D printing of one such Shape Memory Polymer (SMP) tBA-co-DEGDA (tert-Butyl Acrylate with diethylene glycol diacrylate). The novelty lies in establishing the relationship between the various characteristic properties (tensile stress, surface roughness, recovery time, strain fixity, and glass transition temperature) concerning the fact that the print parameters of the laser pulse frequency and print speed are governed in the micro-stereolithography (Micro SLA) method. It is found that the sample printed with a speed of 90 mm/s and 110 pulses/s possessed the best batch of properties, with shape fixity percentages of about 86.3% and recovery times as low as 6.95 s. The samples built using the optimal parameters are further subjected to the addition of graphene nanoparticles, which further enhances all the mechanical and surface properties. It has been observed that the addition of 0.3 wt.% of graphene nanoparticles provides the best results. Full article

The paper discusses the possibility of using in situ generated hybrid polymer-polymer nanocomposites as polymeric materials with triple shape memory, which, unlike conventional polymer blends with triple shape memory, are characterized by fully separated phase transition temperatures and strongest bonding between the polymer blends phase interfaces which are critical to the shape fixing and recovery. This was demonstrated using the three-component system polylactide/polybutylene adipateterephthalate/cellulose nanofibers (PLA/PBAT/CNFs). The role of in situ generated PBAT nanofibers and CNFs in the formation of efficient physical crosslinks at PLA-PBAT, PLA-CNF and PBAT-CNF interfaces and the effect of CNFs on the PBAT fibrillation and crystallization processes were elucidated. The in situ generated composites showed drastically higher values of strain recovery ratios, strain fixity ratios, faster recovery rate and better mechanical properties compared to the blend. Full article

We report a facile approach to control the shape memory effects and thermomechanical characteristics of a lignin-based multiphase polymer. Solvent fractionation of a syringylpropane-rich technical organosolv lignin resulted in selective lignin structures having excellent thermal stability coupled with high stiffness and melt-flow resistance. The fractionated lignins were reacted with rubber in melt-phase to form partially networked elastomer enabling selective programmability of the material shape either at 70 °C, a temperature that is high enough for rubbery matrix materials, or at an extremely high temperature, 150 °C. Utilizing appropriate functionalities in fractionated lignins, tunable shape fixity with high strain and stress recovery, particularly high-stress tolerance were maintained. Detailed studies of lignin structures and chemistries were correlated to molecular rigidity, morphology, and stress relaxation, as well as shape memory effects of the materials. The fractionation of lignin enabled enrichment of specific lignin properties for efficient shape memory effects that broaden the materials’ application window. Electron microscopy, melt-rheology, dynamic mechanical analysis and ultra-small angle neutron scattering were conducted to establish morphology of acrylonitrile butadiene rubber (NBR)-lignin elastomers from solvent fractionated lignins. Full article

In this paper, we experimentally investigate the influence of storage at 40 °C on the shape memory performance and mechanical behavior of a pre-stretched commercial poly(methyl methacrylate) (PMMA). This is to simulate the scenario in many applications. Although this is a very important topic in engineering practice, it has rarely been touched upon so far. The shape memory performance is characterized in terms of the shape fixity ratio (after up to one year of storage) and shape recovery ratio (upon heating to previous programming temperature). Programming in the mode of uniaxial tension is carried out at a temperature within the glass transition range to one of four prescribed programming strains (namely 10%, 20%, 40% and 80%). Also investigated is the residual strain after heating for shape recovery. The characterization of the mechanical behavior of programmed samples after storage for up to three months is via cyclic uniaxial tensile test. It is concluded that from an engineering application point view, for this particular PMMA, programming should be done at higher temperatures (i.e., above its T_g of 110 °C) in order to not only achieve reliable and better shape memory performance, but also minimize the influence of storage on the shape memory performance and mechanical behavior of the programmed material. This finding provides a useful guide for engineering applications of shape memory polymers, in particular based on the multiple-shape memory effect, temperature memory effect, and/or low temperature programming. Full article