Search Results (192)

Studies underscore the significance of coir fibers as a sustainable building material. Based on these insights, this research aims to evaluate coir fiber composite panels of various thicknesses as eco-friendly sound absorbing alternatives to synthetic construction materials like rockwool and fiberglass, aligning its use with the United Nations Sustainable Development Goals. Acoustic absorption was quantified with an impedance tube, and subsequent simulations compared the performance of coir composite panels with that of conventional materials, which constitutes an underexplored evaluation. Using 10 receiver points, the simulations reproduced the acoustic conditions of a multipurpose auditorium before and after the coir covering of parts of the rear and posterior walls. The results indicate that when coir coverings account for approximately 10% of the auditorium surface, reverberation times at 250, 500, 2000, and 4000 Hz are reduced by roughly 1 s. Furthermore, the outcomes reveal that early reflections occur more rapidly in the coir-enhanced model, while the values of the early decay time parameter decrease across all receiver points. Although the original configuration had poor speech clarity, the modified model achieved optimal values at all the measurement locations. These findings underscore the potential of coir fiber panels in enhancing acoustic performance while fostering sustainable construction practices. Full article

Lightweight powder-based sound-absorbing materials are characterized by sound absorption peaks at lower frequencies compared to other sound absorption materials of the same thickness. This behavior is attributed to the excitation of longitudinal vibration modes in the powder particles by incident sound waves, wherein acoustic energy is converted into kinetic energy and subsequently dissipated through interparticle interactions. These lightweight, fine powders are artificially engineered acoustic materials. Despite their structural simplicity, they exhibit emergent and complex sound absorption behaviors through fundamental vibrational mechanisms. Representing the powder layer with a transfer matrix simplifies model-based development and enhances versatility as an acoustic element. The powder layer was modeled as a longitudinally oscillating 1D beam, and transfer matrix of the powder layer was derived. To verify the obtained transfer matrix, the experimental values were compared with the theoretical values for a single powder layer. In addition, both were compared for the case of other acoustic elements stacked on top of each other, which were close to each other. The theoretical values were compared with the experimental values, which were close to each other. Full article

This study investigates the effectiveness of sloped horizontal shading fins in enhancing visual comfort, electricity generation, and acoustic attenuation in a south-facing office room in Wrocław, Poland (51° latitude). A simulation-based approach combined Radiance daylight simulations, PV energy modeling, and graphical acoustic analysis. Four fin configurations were tested to identify the optimal design. The results indicate that Variant 3, featuring two 1 m wide fins inclined at 45°, achieved the best overall performance, increasing UDI_{300–3000/168} from 53.1% to 95.8%, reducing DGP from 50% to 27%, and enabling an estimated annual electricity production of 4.67 MWh. Additionally, applying sound-absorbing material on the shaded side of the fins significantly reduced reflective acoustic wave bounces, significantly reducing façade-exposed noise. This multifunctional solution demonstrates a practical and scalable strategy for improving office environmental quality in temperate climates, contributing to energy efficiency, acoustic comfort, and visual well being. Full article

Material removal processes such as milling, drilling, and turning often generate harmful vibrations that can negatively impact both machine performance and operator safety. Addressing these vibrations at their source or reducing them to safe levels is, therefore, a critical challenge. This study proposes a practical solution by introducing thin-fin-type vibration-absorbing devices fabricated using 3D printing technology. These devices are designed specifically to mitigate vibration propagation during milling operations. To evaluate their effectiveness, a multi-sensor system comprising sound level meters, a vibrometer, and a vision–acoustic camera was employed to measure sound levels. The results show that the use of fabricated devices can reduce noise levels significantly, from 93 dB (comparable to power tools or a lawn mower) to 74 dB (similar to normal conversation or a busy office). This substantial reduction demonstrates the potential of the proposed devices to enhance workplace safety and acoustic comfort on the shop floor. Full article

Open-cell PU foams have a wide range of industrial applications due to their excellent cushioning, impact protection, packaging, thermal insulation, and sound reduction benefits. The foams absorb impact energy while deforming under compressing and are ideal for applications with severe and repeated loading conditions. Enhancing and improving their compressive durability is a vital area of ongoing research. We investigated the effect of incorporating shear-stiffening polymers (SSPs) and shear-thickening fluids (STFs) on the compression properties of open-cell foams. Rheological properties of STFs and SSPs prepared for incorporation into the foams confirmed the shear-thickening and shear-stiffening characteristics. Quasi-static compression tests performed at different speeds (6, 60, 120, 180, and 240 mm/s), as well as load-unload compression tests (6 and 24 mm/s), showed that the SSP-filled foam exhibited the most pronounced improvement in the elastic, plateau, and densification regions compared to the neat foam. While the STF-filled foam also improved performance over the neat foam, its advantages over the SSP-filled foam were less pronounced. The performance of the SSP-filled foam improved with increasing compression speeds, while the performance of the STF-filled foam remained relatively stable between 60 and 240 mm/s of load-unload tests. Post-test compression evaluations showed that neat and STF-filled foams quickly regained their original shape, while SSP-filled foams required more time before recovery. This research shows that combining SSP and STF smart materials with open-cell foams substantially improves their compressive performance, especially at high compression rates and load-unloading scenarios, increasing their functional life. Full article

Membranes can be used in different ways to achieve improvements in sound absorption. They can be used on top of base materials (sound-absorbing materials or other kinds) in such a way that they barely increase the thickness while increasing the sound absorption. They can be positioned inside a sandwich structure for the same purpose. They can also be used independently. There are thin membranes with different characteristics (perforated or otherwise, made up of different thin layers, fabrics made of different yarns, etc.) that are applied to surfaces with a plenum chamber. In all of these foregoing cases it can be difficult to characterise the membrane. Membranes with a smaller thickness lead to difficulties in the positioning of measuring devices thereby increasing the test error. The aim of this work is to obtain airflow resistance and the characteristic acoustic impedance of membranes in a more stable manner. Measurements of the airflow resistance and the characteristic acoustic impedance of sandwich structures with inserted membranes are considered for this purpose. The base material comprising the sandwich was characterised prior to these measurements. These measurements indirectly produce the airflow resistance and the characteristic acoustic impedance of the membrane. The results obtained show more stable measurements of the airflow resistance and the obtaining of the characteristic acoustic impedance of the membrane under the conditions in which it is set. Full article

Due to the significant impedance mismatch between water and air, two types of pipeline silencers designed for the same target frequency with different filling materials often have significantly different thickness. This increases the difficulty in designing silencers for multiple pipelines with different filling materials in narrow spaces. The paper reports a metamaterial design paradigm based on a Helmholtz cavity for low-frequency sound absorption for both air pipelines and water-filled pipelines. An asymmetric absorption metamaterial with coupled Helmholtz resonators is proposed to reduce the impact of low-frequency noise in air pipelines. By coupling the absorption mode and reflection mode, the asymmetric absorption metamaterial with a thickness of 71 mm achieves 95.6% absorption at 403 Hz. The tunable absorbing performance in broadband is confirmed by a finite element simulation. Additionally, a composite metamaterial constructed with HRs associated with a rubber layer is proposed for low-frequency broadband sound absorption in water-filled pipelines. An average absorptance of above 0.8 is achieved over the range of 380–508 Hz by coupling four basic composite metamaterial units with a thickness of 31.5 mm. The proposed design paradigm can reduce the complexity of designing multiple pipelines silencers with different filling materials because the muffler should have similar thickness in the same paradigm. Full article

Polyurethane foam (PF) is a versatile polymer widely used in various applications. By changing the composition of polyol and isocyanate, these foams can be classified into rigid polyurethane foams (PUFRs) and flexible polyurethane foams (PUFFs). The flexible polyurethane foam (PUFFs) is well known for its sound absorption capacities; nevertheless, its flammability poses significant safety hazards. The purpose of this study is to look into how flexible polyurethane foam reacts to fire, specifically its combustion properties, and the risks that come with them. The study aims to find out the rates of horizontal and vertical burning, the make-up of the reaction products, and the temperatures that build up inside the polyurethane foam mass when a support pole is placed in front of the stage and sound-absorbing material is added to stop stage sounds from reverberating. There were performed experiments to determine the fire behavior of the samples in contact with an ignition source in the form of a small flame and experiments to determine the ignition temperature of the sound-absorbing sponge, where it was found that vertical position accelerates combustion, and in practical applications, this aspect must be considered for fire prevention. To determine the combustion gases, several methods were used, namely spectrophotometric, ion chromatography, and gas-chromatographic methods. Analysis of the gases resulting from the combustion of the sound-absorbing sponge indicates the presence of dangerous toxic compounds (hydrogen cyanide, carbon monoxide, and hydrochloric acid), which can endanger human health in the event of a fire. Full article

To address the increasingly complex demands of noise control, this study investigated the integration of a micro-perforated nanofiber membrane (MPNM) with nonwoven fiber felt (NFF), exploiting their synergistic effects to achieve efficient low-frequency broadband sound absorption. Through theoretical analysis, numerical simulations, and experimental validation, the relationship between the sound absorption performance of the composite structure and factors such as the lamination sequence, bonding area, perforation parameters, thickness of the MPNM, and thickness of the NFF were elucidated. These findings provided new insights for the design of high-performance, tunable, sound-absorbing materials. The results demonstrated that the MPNM-NFF effectively combined two distinct sound absorption mechanisms, thereby expanding the effective absorption bandwidth, with particularly enhanced low-frequency sound absorption. Moreover, through algorithmic optimization of the structural parameters, targeted absorption of noise across different frequency bands was achieved, with the optimal average sound absorption coefficients reaching 0.70 in the low-frequency range, 0.91 in the mid-frequency range, and 0.82 in the full-frequency range. This research offered both theoretical foundations and practical guidance for the development of composite materials with high efficiency and broadband sound absorption characteristics, paving the way for innovative applications in noise control materials. Full article

Based on the three-parameter approximate JCAL analytical model (hereinafter referred to as the three-parameter model), this study conducted an in-depth analysis of the effects of porosity, median pore size, and pore size standard deviation on the acoustic performance of porous materials and developed a composite porous material composed of glass fibers and zeolite particles. Experimental results indicate that the pore size distribution significantly affects the acoustic performance of fibrous porous sound-absorbing materials. Specifically, smaller pores lead to better sound absorption at mid–low frequencies, with the optimal sound absorption performance observed when the median pore size is between 60 and 80 μm. Increasing the material density and decreasing the fiber diameter help reduce the internal pore size, thereby improving the material’s sound absorption performance. Additionally, the appropriate addition of zeolite can further optimize the internal pore size and effective sound-absorbing interface, thus enhancing the material’s sound absorption performance. When the material density is 120 kg/m³ and the zeolite substitution rate is around 10%, the material exhibits the best acoustic performance, with a noise reduction coefficient (NRC) reaching 0.65, which is a 10.17% increase compared to the material without zeolite. Comparing the simulation data from the three-parameter model with the actual measurement data shows that the model has excellent predictive performance for the sound absorption coefficient (SAC) of single-fiber porous materials (with an error of approximately 5%). However, for composite porous materials, due to the complex changes in interfaces, there is a certain prediction error (with the maximum error reaching 12.81%), indicating that the model needs further optimization and correction when applied to composite materials. Full article

The structure of foam sound absorbers is not strictly regular, and it is difficult to create a geometric model. In this study, a method for estimating the sound absorption properties of foam sound absorbers with the membrane removed was proposed based on computed tomography (CT) scan images: the circumference of the structure and the cross-sectional area of the voids in the foam cross-section were determined from CT scans of foam materials. The propagation constant and characteristic impedance at the voids were obtained by approximating the foam material cross-section as the clearance between two planes, and the transfer matrix method was used to calculate the normal incident sound absorption coefficient. Further, the sound absorption coefficient was theoretically derived using the effective density with the measured tortuosity applied and compared with the experimental value using a two-microphone impedance measuring tube. By extracting the skeletal part of foam materials by using image processing and removing the residual noise in CT images, and then varying the correction factor for the skeleton surface area, the theoretical value of the sound-absorbing foam without a membrane was closer to the measured value. Full article

Pumice forms when a volcanic explosion ejects highly pressurized, superheated rock, rapidly cooling and depressurizing, resulting in a porous structure. In countries with high volcanic activity, pumice stone is a low-cost natural material that is lightweight, non-toxic, eco-friendly, durable, and heat-resistant. Among other applications, pumice has been used as an aggregate to produce lightweight concrete or cementitious material to produce blended cement or geopolymer. Since pumice stone is highly porous, it could be used as a naturally occurring multiscale porous sound-absorbing material, which may add interesting properties for absorbing sound energy. Normally, a double-porosity granular material presents higher sound absorption at low frequencies than a solid-grain material with the same mesoscopic characteristics at a reduced weight. This study uses theoretical and experimental approaches to investigate the sound absorption characteristics of granular pumice samples. The tests were conducted on crushed pumice stones in granular form. The study suggests that pumice stones can be used as a novel material for sound absorption in room acoustics and noise control applications. Full article

This study draws upon bio-inspiration from anatomical sutures found in hard structures, such as turtle shells, to explore if impact energy can be dissipated through geometric parameterization rather than relying on energy-absorbing materials. While previous finite element analysis studies identified optimal dovetail suture geometries for maximizing the global stiffness and toughness of archway structures, this paper explores how different suture geometries might optimize localization effects through segmentation to isolate damage caused by the propagation of strain energy. We compare the global toughness of each suture geometry to its scaling factor, defined as the ratio of strain energy in the center segment(s) of the archway over the total strain energy absorbed during deformation, normalized by the expected strain energy consistent with uniform volumetric distribution. Our findings indicate that the scaling factor tended to correlate positively with global toughness, suggesting that suture geometries that performed well globally would also exhibit the localization effect. However, there is some nuance in selecting suture geometries that perform well for both metrics, as well as ensuring that geometries that perform well for one type of segmentation are still structurally sound in others, due to little control over where impact may occur, relative to the location of a suture, in real scenarios. Full article

Sheep wool is a precious, renewable raw material that is nowadays disregarded and wasted. To better use local sources of wool, it was used to manufacture tufted carpets. The coarse wool of mountain sheep was used to form a carpet pile layer, while the waste wool from the tannery industry was applied to form carpet underlayment. During investigations, the acoustic performance of the carpets was assessed. The carpets’ sound absorption coefficients and transmission loss were determined using the impedance tube. It was revealed that the adding of underlayment improves the carpet’s sound absorption only at medium sound wave frequencies. The underlayment significantly increases transmission loss in the whole frequency range. The acoustic performance of the carpets with the wool underlayment is similar to the acoustic characteristics of the carpets with an underlayment made from polyester. It was concluded that wool nonwovens can be used as an effective, eco-friendly, sound-absorbing carpet underlayment, which can improve wool utilisation and contribute to the reduction in environmental pollution caused by plastic residues. Full article

The acoustic product development process, crucial for effective noise control, emphasises efficient testing and validation of materials for sound absorption in the R&D phase. Balancing cost-effectiveness, speed, and sustainability, the focus is on minimising excess materials. While strides have been made in reducing sample sizes for estimating random-incident absorption, challenges persist, particularly in establishing validity thresholds for smaller samples with increasing thickness, susceptible to potential overestimation due to edge effects. This study delves into analysing the absorption coefficients of widely used acoustic absorber types—polyester, fibreglass, and open-cell foam—in a full-scale reverberation chamber at Ventac, Blessington, and Wicklow. Demonstrating significant absorption above 500 Hz, these porous absorbers exhibit diminished effectiveness at lower frequencies. The strategic combination of these absorbers with different facings enhances their theoretical broadband absorption characteristics in practical applications. Moreover, the study assesses the validity threshold for reduced sample sizes, employing statistical analysis against ISO 354:2003 standard control samples of the absorber types. Analysis of Variance (ANOVA) on material groups underscores the significant influence of frequency components and sample sizes on the absorption coefficient. The determined validity threshold for 12.8 sqm ISO 354 standard control size is 7.7 sqm for the 25 mm open-cell foam. Similarly, the validity threshold of the 12 sqm ISO 354 standard control size is 9.6 sqm for the 20 mm 800 gsm polyester, 7.2 sqm for the 25 mm fibreglass, and the vinyl black on 25 mm fibreglass. Full article