Search Results (467)

Hydrogel films receive significant attention among researchers because they combine increased stimuli responsiveness and faster responses to the already excellent properties of their component materials. However, their preparation is complex and requires that many difficulties are overcome. The present work presents a new study regarding the preparation of pure and nanoparticle-loaded alginate-based films by spin-coating. Two-microliter solutions of sodium alginate and calcium chloride with different concentrations were deposited on a glass substrate and subjected to rapid rotations of between 100 and 1000 RPM. Film formation can be achieved by optimizing the ratio between the viscosity of the solutions, depending on their concentrations and the rotation speed. When these conditions are in the right range, a homogeneous film is obtained, showing good adherence to the substrate and uniform thickness. Films containing silver nanoparticles were prepared, exploiting the reaction between sodium borohydride and silver nitrate. The two reagents were added to the sodium alginate and calcium nitrate solution, respectively. Their concentration is the driving force for the formation of a uniform film: particles of about 50 nm that are well-dispersed throughout the film are obtained using AgNO₃ at 4 mM and NaBH₄ at 2 or 0.2 mM; meanwhile, at higher concentrations, one can also obtain the precipitation of inorganic crystals. Full article

Eco-friendly mortars have been manufactured with hybrid binders made of blast furnace slag and a reduced amount of clinker. The objective is to explore new formulations suitable for reinforced structures. Previous studies are mainly focused on activation with sulfates, a salt that is corrosive to reinforcing steel. Sodium nitrate and sodium carbonate, easily implementable in construction, have been used as activators in two different concentrations that involve similar Na content. A Type II PC mortar is used as reference. The dimensional stability of the mortars during curing (at 99% RH) and subsequent drying at 40% RH, has been evaluated, as well as their porosity and mechanical properties. Böhme tests revealed that studied hybrid binders have lower wear resistance than PC mortar. Activation with Na₂CO₃ allows the obtention of mortars with reduced porosity and good compression resistance, but generates microcracking that favors chloride diffusion. Activation with nitrates favors precipitation of AFm phases identified through differential thermal analysis. Nitrates in moderate amounts (4% w/w) allow manufacturing hybrid mortars with good resistance to chloride penetration and reasonably good mechanical properties. Hence, this binder can be a promising option for reinforced structures. Higher amounts of nitrates (8%) for activation give rise to more porous mortars. Full article

Improper emissions from industrial activities pose toxicological risks to groundwater safety. Based on an environmental forensic identification case involving livestock (sheep) damage caused by groundwater pollution in a pastoral area, we comprehensively evaluated groundwater quality risks, toxicological risks, and pollution sources using multivariate statistical methods, the Nemerow index method, and a non-carcinogenic health risk model. The potential specific pollutants in the region mainly included calcium, potassium, sodium, magnesium, manganese, fluoride, chloride, sulfate, ammonia nitrogen, total dissolved solids, and nitrate. An evaluation of the groundwater health risk factors showed that fluoride, nitrate, and manganese pose higher health risks (HQ > 1), as fluoride > nitrate > manganese. This suggests that these three pollutants were the primary causes of livestock damage. Identification of pollution sources using multivariate statistical analysis revealed that the main pollutants in the groundwater originate from two rare earth enterprises in the surrounding industrial park, followed by the emissions from animal husbandry. This study provides guidelines into comprehensive regional toxicological risk assessment and source tracing, offering an identification method for similar forensic environmental damage cases. Full article

The clean-label movement has markedly increased consumer demand for meat products free from synthetic additives, such as sodium nitrite, ascorbate, and phosphate. This review summarizes strategies to replace these additives with natural alternatives while preserving the functional and quality properties of traditionally cured meats. Nitrite replacement commonly employs nitrate-rich vegetables, alongside nitrate-reducing starter cultures or pre-converted nitrite powders for adequate nitric oxide production and meat pigment stabilization. Ascorbate substitutes include vitamin C-rich materials and polyphenol-based antioxidants from green tea and rosemary, supporting nitrite reduction and contributing to meat pigment and oxidative stability. To compensate for phosphate functions, natural substitutes such as hydrocolloids, dietary fibers, protein isolates, and calcium powders from eggshells or oyster shells have shown partial success in restoring water-holding capacity, pH buffering, and textural integrity. In addition, non-thermal processing technologies, such as high-pressure processing, ultrasound, and cold plasma are explored as complementary strategies to enhance the efficacy of natural ingredients and support industrial scalability. However, challenges persist regarding ingredient variability, dose-dependent effects, and consistency in functional performance. Future research should focus on synergistic ingredient combinations, formulation standardization, and scalable application in industrial production to ensure the production of high-quality clean-label meat products. Full article

Soil salinization severely limits global agricultural sustainability, particularly across the saline–alkaline landscapes of the Qinghai–Tibet Plateau. We examined how potassium fulvate (PF) modulates oat (Avena sativa L.) performance, soil chemistry, and rhizospheric microbiota in the saline–alkaline soils of the Qaidam Basin. PF markedly boosted shoot and root biomass, with the greatest response observed at 150 kg hm⁻². At the same time, it enhanced soil fertility by increasing organic matter, nitrate-N, ammonium-N, and available potassium, and improved ionic balance by lowering Na⁺ concentrations and the sodium adsorption ratio (SAR), while increasing Ca²⁺ levels and soil moisture content. Under the high-dose treatment (F2), endogenous fungal contributions declined sharply, exogenous replacements increased, and fungal α-diversity fell; multivariate ordinations confirmed that PF reshaped both bacterial and fungal communities, with fungi exhibiting the stronger response. We integrated three machine learning algorithms—least absolute shrinkage and selection operator (LASSO), Random Forest (RF), and eXtreme Gradient Boosting (XGBoost)—to minimize the bias inherent in any single method. We identified microbial β-diversity, organic matter, and Na⁺ and Ca²⁺ concentrations as the most robust predictors of the Soil Salinization and Alkalization Index (SSAI). Structural equation modeling further showed that PF mitigates salinity chiefly by improving soil physicochemical properties (path coefficient = −0.77; p < 0.001), with microbial assemblages acting as key intermediaries. These findings provide compelling theoretical and empirical support for deploying PF to rehabilitate saline–alkaline soils in alpine environments and offer practical guidance for sustainable land management in the Qaidam Basin. Full article

Paddlewheel dirhodium complexes are cytotoxic compounds that are also used as catalysts and in the formation of Rh-based artificial metalloenzymes. Low-temperature structures of adducts formed by the model protein hen egg white lysozyme (HEWL) with dirhodium tetraacetate ([Rh₂(μ-O₂CCH₃)₄]) when crystals of the protein were treated with the metal compound at 20 °C demonstrated that [Rh₂(μ-O₂CCH₃)₄] in part breaks down upon reaction with HEWL; dimeric Rh-Rh units bind the side chains of Asp18 and the C-terminal carboxylate, and monometallic fragments coordinate the side chains of Arg14 and His15 in 20% ethylene glycol, 0.100 M sodium acetate at pH 4.5 and 0.600 M sodium nitrate, while dimeric Rh-Rh units bind the side chains of Asn93 and Lys96, the C-terminal carboxylate and Asp101, with monometallic fragments that bind the side chains of Lys33 and His15 in 0.010 M HEPES pH 7.5 and 2.00 M sodium formate. To verify whether the binding of this metallodrug to proteins also occurs at body temperature, crystals of HEWL were grown in 0.010 M HEPES pH 7.5 and 2.00 M sodium formate at 37 °C and soaked with [Rh₂(μ-O₂CCH₃)₄] at the same temperature. X-ray diffraction data collected on these crystals at 37 °C demonstrate that [Rh₂(μ-O₂CCH₃)₄] reacts with proteins at body temperature. The structures of the Rh/HEWL adduct formed at 20 °C (obtained from data collected at 100 K) and at 37 °C under the same experimental conditions are very similar, with metal binding sites that are conserved. However, metal-containing fragment occupancy is higher in the structure obtained at 37 °C, suggesting a role of temperature in defining the protein metalation process. Full article

The increasing resistance of pathogenic microorganisms to antimicrobials has driven the search for safe and sustainable alternatives. In this context, microbial biosurfactants have gained prominence due to their antimicrobial activity, low toxicity, and high stability under extreme conditions. This study presents the production and characterization of a biosurfactant with antimicrobial potential, obtained from Bacillus subtilis isolated from soil, for application in the control of resistant strains. Bacterial identification was performed using mass spectrometry (MALDI-TOF), confirming it as Bacillus subtilis. The strain B. subtilis UCP 1533 was cultivated using different carbon sources (glucose, soybean oil, residual frying oil, and molasses) and nitrogen sources (ammonium chloride, sodium nitrate, urea, and peptone), with evaluations at 72, 96, and 120 h. The best condition involved a mineral medium supplemented with 2% soybean oil and 0.12% corn steep liquor, resulting in the production of 16 g·L⁻¹ of biosurfactant, with a critical micelle concentration (CMC) of 0.3 g·L⁻¹ and a reduction in water surface tension to 25 mN·m⁻¹. The biosurfactant showed an emulsification index of 100% for used motor oil and ranged from 50% to 100% for different vegetable oils, maintaining stability across a wide range of pH, salinity, and temperature. FT-IR and NMR analyses confirmed its lipopeptide nature and anionic charge. Toxicity tests with Tenebrio molitor larvae showed 100% survival at all the tested concentrations. In phytotoxicity assays, seed germination rates above 90% were recorded for Solanum lycopersicum and Lactuca sativa. Antimicrobial tests revealed inhibitory activity against resistant strains of Escherichia coli and Pseudomonas aeruginosa, as well as against species of the genus Candida (C. glabrata, C. lipolytica, C. bombicola, and C. guilliermondii), highlighting the biosurfactant as a promising alternative in combating antimicrobial resistance (AMR). These results indicate the potential application of this biosurfactant in the development of antimicrobial agents for pharmaceutical formulations and sustainable strategies for phytopathogen control in agriculture. Full article

The unprecedented development of coastal cities in West Africa is marked by anarchic urbanization accompanied by ineffective environmental management, leading to water pollution. This study is conducted in the southern districts of Lomé, Togo, an area built on sandbars where inappropriate attitudes, behaviors, and inadequate hygiene and sanitation practices prevail. The objective of this study is to characterize the quality of groundwater in the study area. Bacteriological and physicochemical analyses were carried out on 11 wells in 10 districts in the southern districts during the four seasons of the year. The analysis shows that the groundwater is polluted in all seasons. Nitrate concentrations exceed 50 mg/L in 65% of the samples, while chloride levels surpassed 250 mg/L in 18% of the cases. Regardless of the season, the dominant facies is sodium chloride and potassium chloride. In all districts, the analysis of microbiological parameters including total germs (30 °C, 100/mL), total coliforms (30 °C, 0/mL), Escherichia coli (44 °C, 2/250 mL), fecal streptococci (0/100 mL), and anaerobic sulfite reducers (44 °C, 2/20 mL) reveals values exceeding the European Union standards (2007). Groundwater contamination is facilitated by the sandy nature of the soil, which increases its vulnerability to various pollutants. Togo continues to experience cholera outbreaks, aggravated by poor sanitation infrastructure and limited vaccination coverage. Public health efforts are directed toward improving sanitation and raising awareness about waterborne and non-communicable diseases. Full article

Platinum was supported on ZSM5 at loadings from 0.1 to 1 wt% and tested for the Selective Catalytic Reduction of NO with H₂ under excess O₂ in a fixed bed reactor to address the issue of NO_x emission abatement from H₂-fueled internal combustion engines avoiding the additional devices for urea storage and injection. To reduce the undesired NO oxidation to NO₂, which is activated by platinum at T > 200 °C, the 0.1%Pt/ZSM5 catalyst was further promoted with sodium. 5 wt% loading of Na strongly inhibited the NO oxidation while giving only a limited impact on the H₂-SCR activity. Unpromoted and Na-promoted catalysts were characterized by XRD, SEM/EDX, N₂ physisorption, and NH₃-TPD to investigate the morphological, structural, and acid properties; H₂ pulse chemisorption and DRIFTS of CO chemisorption were used to investigate the nature of Pt active species. Steady-state and transient operando DRIFTS experiments under NO+H₂+O₂ flow were employed to identify the adsorbed NO_x species interacting with H₂, and reaction intermediates as a function of the reaction conditions. The formation of ammonium intermediates via the reduction of surface nitrate species, playing a key role in H₂-SCR catalyzed by 0.1Pt/ZSM5, was preserved at low Na load whilst NO₂ formation was largely inhibited. Full article

While rhizosphere microbiome functions in saline soils are well documented, complementary microbial strategies between pioneer and late-successional halophytes remain unexplored. Here, we used 16S rRNA sequencing and FAPROTAX functional prediction to compare the rhizosphere bacterial communities of two key halophytes—Suaeda glauca and Phragmites communis—in a reclaimed coastal wetland. The results demonstrate that both plants significantly restructured microbial communities through convergent enrichment of stress-tolerant taxa (Firmicutes, Pseudomonas, Bacillus, and Planococcus) while suppressing sulfur-oxidizing bacteria (Sulfurovum and Thiobacillus). However, they exhibited distinct microbial specialization: S. glauca uniquely enriched organic-matter-degrading taxa (Promicromonospora and Zhihengliuella) and upregulated aromatic compound degradation (2.29%) and ureolysis (0.86%) according to FAPROTAX analysis, facilitating carbon mobilization in early successional stages. Notably, P. communis selectively recruited nitrogen-cycling Serratia, with increased nitrate respiration (3.51% in P. communis vs. 0.91% in S. glauca) function, reflecting its higher nitrogen demand. Environmental factors also diverged: S. glauca’s microbiome correlated with potassium and sodium, whereas P. communis responded to phosphorus and chloride. These findings uncover distinct microbial recruitment strategies by halophytes to combat saline stress—S. glauca–P. communis synergy through microbial carbon-nitrogen coupling—offering a template for consortia design in saline soil restoration. Full article

Coating diamond particle surfaces with a layer of high-temperature resistant nickel, which possesses weldability, effectively enhances the bonding strength between diamond particles and substrates in pre-grinding tools. This improves their stability and strength at high temperatures, thereby enhancing the performance, lifespan, and efficiency of grinding tools. This paper explores the electroless nickel plating process on diamond surfaces, analyzes the working principle of electroless nickel plating on diamond surfaces, and proposes the use of 2 g/L AgNO₃ solution and 2 g/L AgNO₃ + 10 mL/L NH₃·H₂O solution as Pd-free activating solutions. Experimental studies have demonstrated the feasibility of using silver nitrate as an activator, and it has been found that the 2 g/L AgNO₃ + 10 mL/L NH₃·H₂O solution achieves a higher surface plating ratio when used as an activator for electroless nickel plating on diamond surfaces. Based on this, through orthogonal and single-factor experimental methods, the effects of ammonia solution concentration, sodium hypophosphite concentration, plating temperature, and diamond particle size on electroless nickel plating on diamond surfaces were investigated. The optimal process for electroless nickel plating on diamond surfaces was obtained: ammonia solution concentration of 17.5 mL/L, sodium hypophosphite concentration of 33 g/L, and plating temperature of 80 °C. Under this process, using diamond particles with a size of 120/140 for electroless nickel plating, a surface plating ratio of 10.75% electroless nickel-plated diamond can be achieved. Full article

Morocco’s Témara Plain relies heavily on its aquifer system as a critical resource for drinking water, irrigation, and industrial activities. However, this essential groundwater reserve is increasingly threatened by over-extraction, seawater intrusion, and complex hydrogeochemical processes driven by the region’s geological characteristics and anthropogenic pressures. This study aims to assess groundwater quality and its vulnerability to pollution risks and map the spatial distribution of key hydrochemical processes through an integrated approach combining Geographic Information System (GIS) techniques and multivariate statistical analysis, as well as applying the DRASTIC model to evaluate water vulnerability. A total of fifty-eight groundwater samples were collected across the plain and analyzed for major ions to identify dominant hydrochemical facies. Spatial interpolation using Inverse Distance Weighting (IDW) within GIS revealed distinct patterns of sodium chloride (Na-Cl) facies near the coastal areas with chloride concentrations exceeding the World Health Organization (WHO) drinking water guideline of 250 mg/L—indicative of seawater intrusion. In addition to marine intrusion, agricultural pollution constitutes a major diffuse pressure across the aquifer. Shallow groundwater zones in agricultural areas show heightened vulnerability to salinization and nitrate contamination, with nitrate concentrations reaching up to 152.3 mg/L, far surpassing the WHO limit of 45 mg/L. Furthermore, other anthropogenic pollution sources—such as wastewater discharges from septic tanks in peri-urban zones lacking proper sanitation infrastructure and potential leachate infiltration from informal waste disposal sites—intensify stress on the aquifer. Principal Component Analysis (PCA) identified three key factors influencing groundwater quality: natural mineralization due to carbonate rock dissolution, agricultural inputs, and salinization driven by seawater intrusion. Additionally, The DRASTIC model was used within the GIS environment to create a vulnerability map based on seven key parameters. The map revealed that low-lying coastal areas are most vulnerable to contamination. Full article

Biol is a liquid product, obtained by anaerobic fermentation of local inputs, which improves the health of agroecosystems, which is an emerging area in agronomy. The aim of this study consists of the preparation of two biols from inoculums of cow dung (BCD) and native forest duff (BNF) by using specific biodigesters and commercial inputs. The biol characterization was made in terms of mineral (ionic and complex forms), amino acids, hormones and volatile compounds, along with Pfeiffer circular chromatography during fermentation monitoring. The results showed a pH acidic in both biols (4.5–5.5), which is higher for BCD. Also, this biol had higher content in several macro- and micronutrients in ionic (nitrates, phosphates, calcium, iron and sodium) and complex forms (calcium, iron and potassium). Both have interesting content in amino acids and hormones. The absence of microorganisms in the final products could be due to the presence of volatile compounds such as pyrazines and sulfoxides. Along with this, other volatile compounds such as esters were identified, which can be responsible for their pleasant odor. The novelty of this work is to provide a protocol for obtaining biols and to demonstrate their potential to be used as biofertilizers. Full article

Sodium nitrite is an additive commonly used in meat processing to provide technological effects. However, the presence of nitrates in food can lead to the formation of carcinogenic N-nitrosamines; so, its use should be limited. This study concerns the possibility of reducing sodium nitrite (III) addition in the production of canned meat to 50 mg/kg by enriching the product with tomato peels and seeds powder (TPSP). The aim of this study was to evaluate the effect of TPSP on the physicochemical, chemical and microbiological quality of canned pork. Four different products were tested in this study: a control sample and samples with the addition of 0.5%, 1.5%, and 2.5% tomato peels and seeds powder. The addition of TPSP decreased the pH values of meat products and increased yellowness (b*) and redness (a*) values. The influence of TPSP on the increase in antioxidant activity of canned meat was also observed. However, the plant-based additive did not affect the chemical composition or water activity of the tested product. The control samples were characterized by a lower TBARS compared to the other samples of meat products. Microbiological analysis results indicate that the canned pork samples meet the product requirements. The most commonly isolated species from the samples were Enterobacter cloacae, Serratia liquefaciens, and Enterococcus faecalis. Full article

The 4Rs of sports nutrition were proposed in recent years as an evidence-based framework to optimize post-exercise recovery within the context of allostasis. Under this paradigm, it is important to consider that each R represents a factor with a tremendous influence on the allostatic response and improves individual components of the allostatic load (AL), which will positively impact the exercise-induced adaptations and the athlete’s recovery. The 4Rs correspond to the following. (i) Rehydration—This is necessary to guarantee the post-exercise consumption of at least 150% of the body mass lost during the exercise accompanied by sodium (if faster replacement is required). (ii) Refuel—Carbohydrate intake (~1.2 g/kg body mass per hour for up to 4 h post-exercise) is essential not only in restoring glycogen reserves but also in supporting the energy needs of the immune system and facilitating tissue repair. Despite changes in substrate utilization, a ketogenic diet generally has neutral or negative effects on athletic performance compared to carbohydrate-rich diets. (iii) Repair—The ingestion of high-quality protein stimulates post-exercise net muscle protein anabolism and might contribute to faster tissue growth and repair. The use of certain supplements, such as creatine monohydrate, might help to enhance recovery, while tart cherry, omega-3 fatty acids, and dietary nitrate (e.g., Beta vulgaris, Amaranthus L.), as well as other herbal extracts containing flavonoid-rich polyphenols, deserve further clinical research. (iv) Recuperate—Pre-sleep nutrition (casein- or protein-rich meal with slow digestion rate) has a restorative effect, facilitating the recovery of the musculoskeletal, endocrine, immune, and nervous systems. In this article, we update the 4Rs framework, delve deeper into the allostasis paradigm, and offer theoretical foundations and practical recommendations (the 4Rs app) for the assessment of AL in athletes. We cautiously propose an AL index (AL_index) for physique competitors and elite athletes to evaluate the cumulative physiological stress induced by exercise and, thereby, to adjust exercise and nutrition interventions. Full article