Search Results (296)

This study evaluates the potential use of reclaimed sand from municipal wastewater treatment plants (WWTP), categorized as waste under code 19 08 02, as a full substitute for natural sand in cement mortars. The sand was subjected to alkaline pretreatment using sodium hydroxide (NaOH) at concentrations of 0.5%, 1% and 2% to reduce organic impurities and improve surface cleanliness. All mortar mixes were prepared using CEM I 42.5 R as the binder, maintaining a constant water-to-cement ratio of 0.5. Mechanical testing revealed that mortars produced with 100% WWTP-derived sand, pretreated with 0.5% NaOH, achieved a mean compressive strength of 51.9 MPa and flexural strength of 5.63 MPa after 28 days, nearly equivalent to reference mortars with standardized construction sand (52.7 MPa and 6.64 MPa, respectively). In contrast, untreated WWTP sand resulted in a significant performance reduction, with compressive strength averaging 30.0 MPa and flexural strength ranging from 2.55 to 2.93 MPa. The results demonstrate that low-alkaline pretreatment—particularly with 0.5% NaOH—allows for the effective reuse of WWTP waste sand (code 19 08 02) in cement mortars based on CEM I 42.5 R, achieving performance comparable to conventional materials. Although higher concentrations, such as 2% NaOH, are commonly recommended or required by standards for the removal of organic matter from fine aggregates, the results suggest that lower concentrations (e.g., 0.5%) may offer a better balance between cleaning effectiveness and mechanical performance. Nevertheless, 2% NaOH remains the obligatory reference level in some standard testing protocols for fine aggregate purification. Full article

In recent years, biofuels and bioenergy derived from algae have gained increasing attention, fueled by the growing demand for renewable energy sources and the urgent need to lower CO₂ emissions. This research examines the generation of bioethanol and biomethane using freshly harvested and sedimented algal biomass. Employing a factorial experimental design, various trials were conducted, with ethanol yield as the primary optimization target. The findings indicated that the sodium hydroxide concentration during pretreatment and the amylase dosage in enzymatic hydrolysis were key parameters influencing the ethanol production efficiency. Under optimized conditions—using 0.3 M NaOH, 25 μL/g starch, and 250 μL/g cellulose—fermentation yielded ethanol concentrations as high as 2.75 ± 0.18 g/L (45.13 ± 2.90%), underscoring the significance of both enzyme loading and alkali treatment. Biomethane potential tests on the residues of fermentation revealed reduced methane yields in comparison with the raw algal feedstock, with a peak value of 198.50 ± 25.57 mL/g volatile solids. The integrated process resulted in a total energy recovery of up to 809.58 kWh per tonne of algal biomass, with biomethane accounting for 87.16% of the total energy output. However, the energy recovered from unprocessed biomass alone was nearly double, indicating a trade-off between sequential valorization steps. A comparison between fresh and dried feedstocks also demonstrated marked differences, largely due to variations in moisture content and biomass composition. Overall, this study highlights the promise of integrated algal biomass utilization as a viable and energy-efficient route for sustainable biofuel production. Full article

The aim of the study was to develop a suitable pre-treatment (and more specifically, the etching operation) of 3D-printed PET and PETG samples with different filling densities of the inner layers for subsequent electroless metallization. The influence of temperature, etching time, and sodium hydroxide concentration in the etching solution on the deposition rate, adhesion, and composition of Ni-P coatings was determined. The studies show that a high temperature and concentration of the etching solution do not improve the properties of the coating. The etching not only plays an important role in improving adhesion but also affects the composition and thickness of the nickel layer. It was also established how the degree of filling densities of the inner layers affects the uniformity, penetration depth, and thickness of electrolessly deposited Cu and Ni-P coatings on 3D PETG samples. Full article

This study investigates the structural effects of dilute acid and alkali treatments on cotton fibers, aiming to understand the influence of chemical pretreatment on cellulose morphology. Cotton samples were exposed to 1% sulfuric acid and 1% sodium hydroxide at 90 °C, and the resulting changes were evaluated using scanning electron microscopy and nonlinear optical imaging techniques. The results indicate that sulfuric acid causes significant fiber degradation, leading to fragmentation and reduced fiber thickness. In contrast, sodium hydroxide treatment results in a roughened, flaky surface while preserving the overall structural integrity, with fibers appearing fluffier and more accessible to enzymatic processes. Untreated cotton fibers maintained a smooth and uniform surface, confirming the chemical specificity of the observed changes. These findings are crucial for optimizing biomass pretreatment methods, demonstrating that dilute chemical treatments primarily affect macrostructural features without significantly disrupting the cellulose microfibrils. The study provides valuable insights for the development of efficient biorefining processes and sustainable bio-based materials, highlighting the importance of selecting appropriate chemical conditions to enhance enzymatic hydrolysis and biomass conversion while maintaining the core structure of cellulose. This research contributes to advancing the understanding of cellulose’s structural resilience under mild chemical pretreatment conditions. Full article

The treatment with an alkali (sodium hydroxide) solution of acid-activated montmorillonite clay minerals resulted in a reduction in specific surface area. However, a significant enhancement in the removal of basic blue-41 dye solution was achieved compared to acid-activated samples only (first step of activation) and to the raw montmorillonite clay. The obtained products were characterized using different techniques. The results indicated that the acid-activated montmorillonites exhibited different physicochemical properties than the starting raw montmorillonite, with a reduction in the cation exchange capacity and improvements in the specific surface area (from 5 m²/g to 274 m²/g) and total pore volume (from 0.031 cm³/g to 0.450 cm³/g) due to the formation of the amorphous silica phase. However, the treatment with NaOH solution was accompanied by significant reductions in the specific surface area (from 274 m²/g to 18 m²/g) and total pore volume (from 0.450 cm³/g to 0.02 cm³/g) due to the dissolution of the formed amorphous silica phase, as confirmed through ²⁹Si MAS NMR and FTIR techniques. In addition, the SiO₂/Al₂O₃ molar ratios were close to those of the starting montmorillonite clay. The removal of the cationic basic blue-41 was optimized under different conditions, such as different initial concentrations, adsorbent doses, and pHs of the dye solution. The maximum removal capacities of acid-activated clays were in the range of 45 mg/g to 80 mg/g and decreased with the extent of the acid activation process. However, the capacities were enhanced after NaOH treatment and reached values in the range of 80 to 120 mg/g. Enhancing the surface area had less of an impact on the materials’ removal ability. The obtained materials performed well in seven adsorption–regeneration cycles, showing a 70% reduction in removal effectiveness. Full article

Water regeneration in PVC production is a key issue to consider, given the high freshwater consumption rate of the process. This research evaluates the inherent safety of poly(vinyl chloride) (PVC) production via suspension polymerization by implementing mass and energy integration strategies in combination with wastewater regeneration under a zero-liquid-discharge (ZLD) approach. The impact of these integrations on process safety was examined by considering the risks associated with the handling of hazardous materials and critical operations, as well as the reduction in waste generation. To this end, the Inherent Safety Index (ISI) methodology was employed, which quantifies hazards based on factors such as toxicity and flammability, enabling the identification of risks arising from system condition changes due to the implementation of sustainable water treatment technologies. Although the ISI methodology has been applied to various chemical processes, there are few documented cases of its specific application in PVC plants that adopt circular production strategies and water resource sustainability. Therefore, in this study, ISI was used to thoroughly evaluate each stage of the process, providing a comprehensive picture of the safety risks associated with the use of sustainable technologies. The assessment was carried out using simulation software, computer-aided process engineering (CAPE) methodologies, and information obtained from safety repositories and expert publications. Specifically, the Chemical Safety Index score was 22 points, with the highest risk associated with flammability, which scored 4 points, followed by toxicity (5 points), explosiveness (2 points), and chemical interactions, with 4 points attributed to vinyl chloride monomer (VCM). In the toxicity sub-index, both VCM and PVC received 5 points, while substances such as sodium hydroxide (NaOH) and sodium chloride (NaCl) scored 4 points. In the heat of reaction sub-index, the main reaction scored 3 points due to its high heat of reaction (−1600 kJ/kg), while the secondary reactions from PVA biodegradation scored 0 points for the anoxic reaction (−156.5 kJ/kg) and 3 points for the aerobic reaction (−2304 kJ/kg), significantly increasing the total index. The Process Safety Index scored 15 points, with the highest risk found in the inventory of hazardous substances within the inside battery limits (ISBL) of the plant, where a flow rate of 3241.75 t/h was reported (5 points). The safe equipment sub-index received 4 points due to the presence of boilers, burners, compressors, and reactors. The process structure scored 3 points, temperature 2, and pressure 1, reflecting the criticality of certain operating conditions. Despite sustainability improvements, the process still presented significant chemical and operational risks. However, the implementation of control strategies and safety measures could optimize the process, balancing sustainability and safety without compromising system viability. Full article

Investigating viable processes for the use of lignocellulosic biomass in clean fuels and high-value-added chemical products is essential for sustainable development. Large amounts of lignin are available every year as by-products of the paper and biorefinery industries, causing a series of problems, particularly environmental ones. Its structure and composition make lignin compatible with the concept of sustainability, since it can be used to produce new chemical products with high added value. As such, this study aims to extract lignin from green coconut fiber (LIG), with the subsequent impregnation of a sodium-octanoate-based surfactant (LIG-SUR), and determine its applicability as an adsorbent for removing copper ions from synthetic waste. To this end, the green coconut fiber lignocellulosic biomass was initially subjected to alkaline pre-treatment with 2% (w/v) sodium hydroxide in an autoclave. Next, the surface of the lignin was modified by impregnating it with sodium octanoate, synthesized from the reaction of octanoic acid and NaOH. The physical and chemical traits of the lignin were studied before and after surfactant impregnation, as well as after copper ion adsorption. The lignin was analyzed by X-ray fluorescence (XRF), Fourier transform infrared (FTIR) and scanning electron microscopy (SEM). The adsorption tests were carried out using lignin pre-treated with surfactant in a batch system, where the effects of pH and adsorbent concentration were investigated. XRF and SEM analyses confirmed surfactant impregnation, with Na₂O partially replaced by CuO after Cu²⁺ adsorption. FTIR analysis revealed shifts in O–H, C–H, C=O, and C=C bands, indicating electrostatic interactions with lignin. Adsorption kinetics followed the pseudo-second-order model, suggesting chemisorption, with equilibrium reached in approximately 10 and 60 min for LIG-SUR and LIG, respectively. The Langmuir model best described the isotherm data, indicating monolayer adsorption. LIG-SUR removed 91.57% of Cu²⁺ and reached a maximum capacity of 30.7 mg·g⁻¹ at 25 °C and a pH of 6. The results of this research showed that pre-treatment with NaOH, followed by impregnation with surfactant, significantly increased the adsorption capacity of copper ions in solution. This technique is a viable and sustainable alternative to the traditional adsorbents used to treat liquid waste. In addition, by using green coconut fiber lignin more efficiently, the research contributes to adding value to this material and strengthening practices in line with the circular economy and environmental preservation. Full article

Sustainable valorization of lignocellulosic biomass, such as wheat straw (WS), into valuable products is key for efficient resource utilization. This study investigated an integrated strategy combining Irpex lacteus fermentation with subsequent alkali extraction to improve WS valorization. Alkali extraction parameters, including sodium hydroxide concentration, solid-to-liquid (S:L) ratio, temperature, and time, were optimized based on polysaccharide yield and purity. Optimal conditions were identified as 0.8 mol/L sodium hydroxide, a 1:25 S:L ratio, 90 °C, and 1 h, yielding 6.63% polysaccharides with 52.01% purity. Compared to untreated straw, the combined fermentation and alkali extraction treatment significantly altered the WS residue’s composition and structure, substantially reducing hemicellulose and acid detergent lignin while consequently increasing relative cellulose content. This enhanced cellulose accessibility resulted in a markedly improved glucose yield upon enzymatic hydrolysis, reaching 586 g/kg dry matter for the residue after combined treatment. Demonstrating a strong synergistic effect, this yield represents a 5.42-fold increase compared to untreated WS and a 3.30-fold increase compared to solely fermented straw. Analyses of SEM, FTIR, and XRD confirmed that the integrated treatment effectively disrupted the lignocellulosic structure by removing lignin and hemicellulose. This created a more porous morphology and increased cellulose exposure, which was deemed more critical for hydrolysis than the observed 18.58% increase in the cellulose crystallinity index relative to untreated straw. Thermogravimetric analysis further reflected these structural and compositional changes through altered thermal decomposition profiles. Therefore, integrating polysaccharide extraction with fungal fermentation is a highly effective strategy for improving resource efficiency in WS valorization. This approach enables the efficient co-production of valuable polysaccharides alongside significantly boosted platform sugar yields, offering a promising route towards more economically viable and sustainable WS utilization. Full article

The uranium tailings mineral body is large and loose, and this could lead to radioactive contamination. Nuclides and heavy metals released from uranium tailings can be reduced through reinforcement treatment. The current study investigated the effect of CaCl₂ solutions with the same volume and different mass fractions on uranium tailing reinforcement under the premise of fixing the dosage of metakaolin, sodium hydroxide, sodium silicate, and the water reducer. It was found that, when 20.0% CaCl₂ was injected, the hydration reaction occurred more efficiently, and a more uniform gel polymer was produced. The degree of polymerization was higher, as well as the degree of aggregation near macropores. A large number of closed mesopores formed on the solidified surface. The pore structure of the solidified body was significantly improved; uranium ore particles had smaller gaps between them; the solidified body was better compacted; the leaching rates of uranium and its heavy metal ions were significantly reduced; and the compressive strength of the solidified body improved. In the triaxial test, the solidified body had a strength increase of 4.7 times. In addition to SEM, XPS, and XRD, the solidified samples were analyzed. In uranium slag solidified bodies, C-S-H and C-A-H gels and C-A-S-H and N-A-S-H polymers were formed. The gel polymers were wrapped around the uranium tailing particles, resulting in an 82.6% reduction in uranium leaching and a 57.2% reduction in radon exhalation. Full article

Feeding accounts for approximately 70% of total costs in livestock production, underscoring the need for cost-effective and high-quality alternative feed sources. Almond hulls (AHs), a byproduct of the almond processing industry, represent a promising option due to their availability and potential nutritional value. Moreover, their inclusion in animal diets contributes to a reduction in environmental waste associated with their disposal. This study examined the effects of incorporating 4% sodium hydroxide (NaOH)-treated AHs into the diets of Assaf sheep (rams, ewes, and growing lambs) on feed utilization and animal performance. The experiment evaluated the chemical composition of AHs, nutrient digestibility, sexual behavior and semen quality in rams, milk composition in ewes, and the performance of growing lambs fed diets with increasing levels of inclusion of AHs. A total of 60 ewes and 21 rams were randomly assigned to one of three treatment groups, receiving diets containing 0%, 20%, or 40% AHs. NaOH treatment reduced the concentrations of organic matter and fiber fractions, while increasing the crude protein concentration of AHs (p < 0.01). Diets containing AHs did not affect nutrient digestibility (p > 0.05). Feeding a diet with 40% Na-OH-treated AHs significantly improved the daily weight gain (p = 0.002) of growing lambs up to 70 days after birth, and enhanced (p < 0.05) the libido, scrotal circumference, and semen quality of mature rams. In addition, ewes fed a diet containing 40% AHs showed (p < 0.05) improved fertility, prolificacy, and milk quality. NaOH-treated AHs are a cost-effective and sustainable feed ingredient that can improve reproductive performance and milk production, thereby increasing overall livestock productivity. The 40% inclusion level yielded the most favorable outcomes across all performance parameters evaluated in rams, ewes, and lambs. Full article

Fly ash, a byproduct of coal burning and gasification, is a significant source of global pollution and is classified as hazardous waste. However, physicochemical treatments can improve their adsorption capacity by increasing their surface area. This research aimed to enhance the adsorption capacity of fly ash from the brick manufacturing industry to remove Cd(II) ions by optimizing its surface area. The treatment process was designed with two factors: sodium hydroxide concentration and stirring time, each evaluated at three levels. The modification was confirmed through X-ray diffraction analysis of its mineralogical composition. Using the BET method, the initial fly ash exhibited a surface area of 8.59 m²/g, which increased to a maximum of 33.99 m²/g after treatment. The proposed modification method successfully quadrupled the surface area under optimal conditions: 2.0 M NaOH concentration and 60 min of stirring. The 3² factorial design shows that the highest degree of Cd(II) removal is 99.75%, which is achieved using the modified fly ash with a surface area of 33.99 m²/g under favorable operating conditions of 30 min and 600 rpm stirring speed. Full article

Improving surface bioactivity is crucial to acquiring zirconia implants with ideal osteoconductivity. In this work, we enhanced the surface properties of zirconia implants, specifically roughness, hydrophilicity, and osteoconductivity, using a “one-step” femtosecond laser (FSL) treatment in air, deionized water, and sodium hydroxide solution. Zirconia specimens were treated in these media, and their surface morphology, chemical composition, and osteoconductivity were evaluated through various assays. The results showed that FSL treatment successfully created micro/nanoporous structures and increased roughness across all specimens. The liquid media treatment facilitated the grafting of hydroxyl (-OH) groups, significantly improving hydrophilicity. The L-NaOH group exhibited a higher hydroxyl content (28%) compared to the L-Air group (10%), reducing the contact angle significantly. Enhanced osteoblast differentiation and mineralization, along with improved gene expression, were observed in the L-Water and L-NaOH groups. In conclusion, the one-step FSL treatment developed a dual-function bioactive zirconia surface, offering an effective method for the biomedical functionalization of zirconia implants. Full article

The metabolic cycle of L-proline plays a crucial role in cancer cell survival, proliferation, and metastasis. A key intermediate in the biosynthesis and degradation of proline is 3,4-dihydro-2H-pyrrole-2-carboxylic acid. A direct route for synthesizing substituted derivatives of this acid involves the cyclization of 2-amino-5-oxonitriles. Michael additions of [(diphenylmethylene)amino]acetonitrile to enones in a basic medium—either with aqueous sodium hydroxide or under solid–liquid phase-transfer catalysis conditions using CaO as a base—enable the synthesis of substituted 2-amino-5-oxonitriles as single diastereoisomers or as diastereoisomeric mixtures. Selective removal of the diphenylmethylene-protecting group, followed by in situ cyclization in acidic conditions, yields trans- and cis-3,5-diaryl-3,4-dihydro-2H-pyrrole-2-carbonitriles. The reaction of nitriles with HCl/dioxane/methanol followed by treatment with water produces esters and amides as by-products. In vitro screening of the synthesized compounds against multiple human cancer cell lines revealed that some compounds exhibit a good or high selectivity index. In conclusion, the synthetic schemes presented offer simple and efficient routes for the preparation of the derivatives of substituted 3,4-dihydro-2H-pyrrole-2-carboxylic acids, with some compounds exhibiting promising antiproliferative activity. Full article

The traditional alkaline process used to prepare sodium stannate faces the challenges of high temperature, low utilization rate, and large hydrogen peroxide consumption, which is mainly due to the low oxidation dissolution efficiency of tin. Here, a new process by ultrasonic-enhanced oxidation and dissolution efficiency of tin at room temperature was proposed. The effects of temperature, ultrasonic power, sodium hydroxide concentration, hydrogen peroxide dosage, and ultrasonic time on the oxidation dissolution efficiency of tin were systematically investigated. The results show that the process of ultrasonic-enhanced oxidation dissolution of tin is a new method with high efficiency and low cost. At room temperature, the tin dissolution efficiency was as high as 99.3% under ultrasound, which was 28% higher than that of the conventional method under the same conditions. The introduction of ultrasound promoted the generation of strong oxidizing hydroxyl radicals (·OH) from hydrogen peroxide, significantly improved the surface roughness of the tin sheet from 6.875 μm in the conventional treatment to 34.135 μm in the ultrasonic treatment, and destroyed the passivation layer on the surface of the tin sheet, thereby improving the dissolution efficiency of tin. Compared with conventional tin dissolution conditions, ultrasonic-enhanced oxidation could decrease the reaction temperature by 30 °C, reduce the consumption of sodium hydroxide by 33.3%, and save the consumption of hydrogen peroxide by 15% while achieving the same tin dissolution effect. This new technology provides new ideas for the oxidation and dissolution of this valuable metal. Full article

This study examined the hierarchical structuring of *BEA zeolite using two distinct approaches: double aluminum removal with solid ammonium hexafluorosilicate (2x-AHFS) and a solution of 0.2 M sodium hydroxide followed by 0.5 M hydrochloric acid (T-NaOH). Additionally, niobium pentoxide (Nb₂O₅) was impregnated at different loadings (5, 10, 15, and 20 wt.%) onto the hierarchized materials. Both treatments increased the SiO₂/Al₂O₃ ratio and produced crystals with domains of about the same size. The hierarchization methods generated secondary mesopores and reduced the micropores in the treated HB zeolite. The solid-state NMR analysis by ²⁷Al and ²⁹Si indicated that the 2x-AHFS treatment increased the hydrophobic character of the zeolite, while the treatment with NaOH/HCl resulted in a less hydrophobic material. A balanced quantity of Brønsted and Lewis sites was observed for all treated zeolites. Thus, these combined physicochemical characteristics of the new catalysts may explain their superior performance in the dehydration reactions. In the case of ethanol dehydration at 230 °C, the 20 wt.% Nb₂O₅ supported on the T-NaOH catalyst produced an 84% conversion and 86% selectivity for ethylene (EE), with 14% diethyl ether (DEE) as the only products. Conversely, in the 1-propanol dehydration reaction, the 20 wt.% Nb₂O₅ supported on 2x-AHFS achieved 99% conversion, producing 99% propene. Full article