Search Results (21)

Sensitive and on-site detection of pesticide residues remains a critical challenge for food safety, particularly in developing regions where rapid screening tools are urgently needed. Herein, we report a flexible surface-enhanced Raman scattering (SERS) platform based on triangular silver nanoplates (TSNPs) integrated onto a polydimethylsiloxane (PDMS) substrate, enabling sensitive and conformal detection of paraquat residues on agricultural surfaces. TSNPs were synthesized via a seed-mediated photochemical growth method and formulated into a TSNP ink, which was directly deposited onto oxygen-plasma-treated and thiol-functionalized PDMS substrates. Owing to the highly anisotropic geometry and sharp edges of TSNPs, the flexible SERS substrate exhibits strong localized surface plasmon resonance (LSPR) enhancement and mechanically stable electromagnetic hot spots. Systematic optimization of TSNP optical absorbance revealed that uniform nanoplate distribution and optimal hotspot density were achieved at an absorbance of 2.0. The SERS performance was evaluated using rhodamine 6G under front-side and back-side illumination configurations, demonstrating good signal reproducibility and a detection limit of approximately 10⁻⁵ M. Notably, back-side illumination through the PDMS layer provided superior SERS responses due to improved optical transmission and light–matter interaction. The practical applicability was further demonstrated through back-side SERS detection of paraquat on aluminum foil as a model surface, achieving a lowest detectable concentration of 5 × 10⁻⁶ M, followed by damage-free detection on Chinese pear peels. This work highlights a reliable and nondestructive flexible SERS platform for on-site pesticide residue monitoring. Full article

Direct-writing submicron copper circuits on glass with laser precision—without lithography, vacuum deposition, or etching—represents a transformative step in next-generation microfabrication. We present a high-resolution, maskless method for metallizing glass using ultrashort pulse Bessel beam laser processing, followed by silver ion activation and electroless copper plating. The laser-modified glass surface hosts nanoscale chemical defects that promote the in situ reduction of Ag⁺ to metallic Ag⁰ upon exposure to AgNO₃ solution. These silver seeds act as robust catalytic and adhesion sites for subsequent copper growth. Using this approach, we demonstrate circuit traces as narrow as 0.7 µm, featuring excellent uniformity and adhesion. Compared to conventional redistribution-layer (RDL) and under-bump-metallization (UBM) techniques, this process eliminates multiple lithographic and vacuum-based steps, significantly reducing process complexity and production time. The method is scalable and adaptable for applications in transparent electronics, fan-out packaging, and high-density interconnects. Full article

Photodetectors and gas sensors are vital in modern technology, spanning from environmental monitoring to biomedical diagnostics. This paper explores the UV detection and gas sensing properties of a zinc oxide (ZnO) nanorod array (ZNA) grown on silver nanowire mesh (AgNM) using a hydrothermal method. We examined the impact of different zinc acetate precursor concentrations on their properties. Results show the AgNM forms a network with high transparency (79%) and low sheet resistance (7.23 Ω/□). A sol–gel ZnO thin film was coated on this mesh, providing a seed layer with a hexagonal wurtzite structure. Increasing the precursor concentration alters the diameter, length, and area density of ZNAs, affecting their performance. The ZNA-AgNM-based photodetector shows enhanced dark current and photocurrent with increasing precursor concentration, achieving a maximum photoresponsivity of 114 A/W at 374 nm and a detectivity of 6.37 × 10¹⁴ Jones at 0.05 M zinc acetate. For gas sensing, the resistance of ZNA-AgNM-based sensors decreases with temperature, with the best hydrogen response (2.71) at 300 °C and 0.04 M precursor concentration. These findings highlight the potential of ZNA-AgNM for high-performance UV photodetectors and hydrogen gas sensors, offering an alternative way for the development of future sensing devices with enhanced performance and functionality. Full article

Due to the lower cost compared to screen-printed silver contacts, the Ni/Cu/Ag contacts formed by plating have been continuously studied as a potential metallization technology for solar cells. To address the adhesion issue of backside grid lines in electroplated n-Tunnel Oxide Passivating Contacts (n-TOPCon) solar cells and reduce ohmic contact, we propose a novel approach of adding a Ni/Si alloy seed layer between the Ni and Si layers. The metal nickel layer is deposited on the backside of the solar cells using electron beam evaporation, and excess nickel is removed by H₂SO₄:H₂O₂ etchant under annealing conditions of 300–425 °C to form a seed layer. The adhesion strength increased by more than 0.5 N mm⁻¹ and the contact resistance dropped by 0.5 mΩ cm² in comparison to the traditional direct plating Ni/Cu/Ag method. This is because the resulting Ni/Si alloy has outstanding electrical conductivity, and the produced Ni/Si alloy has higher adhesion over direct contact between the nickel–silicon interface, as well as enhanced surface roughness. The results showed that at an annealing temperature of 375 °C, the main compound formed was NiSi, with a contact resistance of 1 mΩ cm⁻² and a maximum gate line adhesion of 2.7 N mm⁻¹. This method proposes a new technical solution for cost reduction and efficiency improvement of n-TOPCon solar cells. Full article

In this study, a mesoscale Weather Research and Forecast (WRF) model coupled with an AgI (silver iodide) cold cloud catalytic module were used to explore the potential impact of the catalytic position and rate in the catalytic module based on a ground rain enhancement operation in the Qilian Mountains, on 16 August 2020. Results show that the simulated precipitation, liquid water content (LWC), and water vapor content (PWV) are in good agreement with the observations, demonstrating that the WRF model using the coupled AgI cloud-seeding scheme is well-applicable to the precipitation simulation of the Qilian Mountains. It is also observed that there are some differences in the catalytic effect of catalysis at different cloud temperatures. The precipitation enhancement effect is the most favorable in the fifth layer of 15 km, followed by that in the fourth layer of 12 km and the sixth layer of 18 km. Considering the flight cost and catalytic efficiency, the fourth layer is highly recommended for seeding. Furthermore, the AgI seeding rate also plays a crucial impact on ground precipitation. In the case of a seeding rate of about 1.2 g·s⁻¹, the precipitation enhancement effect tends to be stable, and the percentage of the precipitation increase reaches up to 10.4%. While in the case of a seeding rate of about 1.5 g·s⁻¹, the percentage of ground precipitation increase is 10%, which is 0.4% lower than that of 1.2 g·s⁻¹. In summary, the introduction of a AgI catalyst with a seeding rate of 1.2 g·s⁻¹ can significantly increase the ground precipitation at a height of 12 km and a temperature of −3 °C in the Qilian Mountains. Full article

Aflatoxins produced by some species of Aspergillus are considered secondary toxic fungal by-products in feeds and food. Over the past few decades, many experts have focused on preventing the production of aflatoxins by Aspergillus ochraceus and also reducing its toxicity. Applications of various nanomaterials in preventing the production of these toxic aflatoxins have received a lot of attention recently. The purpose of this study was to ascertain the protective impact of Juglans-regia-mediated silver nanoparticles (AgNPs) against Aspergillus-ochraceus-induced toxicity by exhibiting strong antifungal activity in in vitro (wheat seeds) and in vivo (Albino rats) settings. For the synthesis of AgNPs, the leaf extract of J. regia enriched with high phenolic (72.68 ± 2.13 mg GAE/g DW) and flavonoid (18.89 ± 0.31 mg QE/g DW) contents was used. Synthesized AgNPs were characterized by various techniques, including TEM, EDX, FT-IR, and XRD, which revealed that the particles were spherical in shape with no agglomeration and fine particle size in the range of 16–20 nm. In vitro antifungal activity of AgNPs was tested on wheat grains by inhibiting the production of toxic aflatoxins by A. ochraceus. According to the results obtained from High-Performance Liquid Chromatography (HPLC) and Thin-Layer Chromatography (TLC) analyses, there was a correlation between the concentration of AgNPs and a decrease in the production of aflatoxin G1, B1, and G2. For in vivo antifungal activity, Albino rats were administrated with different doses of AgNPs in five groups. The results indicated that the feed concentration of 50 µg/kg feed of AgNPs was more effective in improving the disturbed levels of different functional parameters of the liver (alanine transaminase (ALT): 54.0 ± 3.79 U/L and aspartate transaminase (AST): 206 ± 8.69 U/L) and kidney (creatinine 0.49 ± 0.020 U/L and BUN 35.7 ± 1.45 U/L), as well as the lipid profile (LDL 22.3 ± 1.45 U/L and HDL 26.3 ± 2.33 U/L). Furthermore, the histopathological analysis of various organs also revealed that the production of aflatoxins was successfully inhibited by AgNPs. It was concluded that the harmful effects of aflatoxins produced by A. ochraceus can be successfully neutralized by using J. regia-mediated AgNPs. Full article

Silver films with a thickness below 50 nanometer were deposited on glass using DC magnetron sputtering. The chemical stability of the films was investigated by exposure of the film to a droplet of a HCl solution in a humid atmosphere. The affected area was monitored with a digital microscope. The affected area increases approximately linearly with time which points to a diffusive mechanism. The slope of the area versus time plot, or the diffusivity, was measured as a function of the acid concentration, the presence of an aluminum seed layer, and film thickness. The diffusivity scales linearly with the acid concentration. It is shown that the diffusivity for Al-seeded Ag films is much lower. The behavior as function of the film thickness is more complex as it shows a maximum. Full article

Ag has the lowest electrical resistivity among all metals, and at the same time, the best optical properties in the visible and near-IR spectral range; it is therefore the most widely employed material for thin-metal-film-based transparent conductors. In this work, an ultra-thin transparent silver film electrode with aluminum as seed layer was prepared by a resistive thermal evaporation technique. Using a range of electrical, optical and surface morphology techniques, it can be noted that the presence of the thin layer of aluminum changes the growth kinetics (nucleation and evolution) of the thermal evaporation of Ag, leading to silver films with smooth surface morphology and high electrical conductivity, and the threshold thickness of the silver film is reduced. It is inferred that the aluminum layer showed a good infiltration effect on the ultra-thin silver film, by analyzing the transmittance spectrum, sheet resistance and surface morphology. Moreover, the average transmittance of silver film with 10 nm is 40% in the 400–2500 nm band, whereas the sheet resistance is 13 Ωsq ⁻¹. A series of experiments show that the introduction of Al seed layer has certain effect on improving the properties of transparent conductive silver films. Then, a new method for deposition of 1 nm Al seed layer was proposed; that is, the 1 nm aluminum infiltrated layer is divided into two or more layers, and the average transmittance of silver film with 5 nm is 60% in the 400–2500 nm band, whereas the sheet resistance does not exceed 100 Ω sq⁻¹. Full article

The demand for transparent conductive coatings has increased over recent years, leading to the development of various technical solutions. One of the approaches is to use metallic coatings very close to their coalescence thickness, so that a good compromise between transparency and conductivity is obtained. In this contribution, a combination of two elements with high potential in this field is used, namely silver and copper. The continuity of silver films on a dielectric transparent substrate is significantly improved by the addition of a copper seed layer that promotes the formation of a continuous layer at smaller effective thicknesses. Two distinct deposition processes are used for the deposition of the two materials, namely HiPIMS (High Power Impulse magnetron sputtering) for copper and DC sputtering for silver. The use of HiPIMS enables a better control of the structure and quantity of deposited material, allowing us to deposit a very small amount of material. The mono-element coatings are characterized from the optical and electrical point of view, and then mixed to form a structure with better transparency, up to 80% in the visible spectrum, good electrical properties, resistivity of ~2 × 10⁻⁵ (Ω × cm), and significantly lower surface roughness, down to 0.2 nm. Full article

A novel and cost-effective method for the fabrication of highly conductive Al/Ag core-shell structured microspheres was proposed and investigated. The oxidative co-deposition of catechol and polyamine was firstly performed to modify the surface of the aluminum microsphere. Then, a two-step electroless plating was conducted to fabricate the Al/Ag microspheres. During the first step of the electroless plating process, the surface of the aluminum microsphere was deposited with silver nanoparticle seeds using n-octylamine and ethylene glycol. Then, during the second step of the electroless plating process, silver particles grew evenly to form a compact silver shell on the surface of aluminum via a silver mirror reaction. According to the scanning electron microscope and energy dispersive X-ray results, a compact and continuous silver layer was successfully generated on the surface of the aluminum. The valence of the sliver on the surface of the aluminum was confirmed to be zero, based on the X-ray photoelectron spectrometer and X-ray diffractometer analyses. As a result, the as-prepared Al/Ag microspheres exhibited a high conductivity of 10,000 S/cm. The Al/Ag/MVQ composite demonstrated low electrical resistivity of 0.0039 Ω·cm and great electromagnetic interference shielding effectiveness at more than 70 dB against the X-band, and this result suggests that the as-prepared composite is a promising conductive and electromagnetic shielding material. Full article

Nitric oxide (NO) is a toxic gas, which is dangerous for human health and causes many respiratory infections, poisoning, and lung damage. In this work, we have successfully grown ZnO nanorod film on annealed ZnO seed layer in different ambient temperatures, and the morphology of the nanorods sensing layer that affects the gas sensing response to nitric oxide (NO) gas were investigated. To acknowledge the effect of annealing treatment, the devices were fabricated with annealed seed layers in air and argon ambient at 300 °C and 500 °C for 1 h. To simulate a vertical device structure, a silver nanowire electrode covered in ZnO nanorod film was placed onto the hydrothermal grown ZnO nanorod film. We found that annealing treatment changes the seed layer’s grain size and defect concentration and is responsible for this phenomenon. The I–V and gas sensing characteristics were dependent on the oxygen defects concentration and porosity of nanorods to react with the target gas. The resulting as-deposited ZnO seed layer shows better sensing response than that annealed in an air and argon environment due to the nanorod morphology and variation in oxygen defect concentration. At room temperature, the devices show good sensing response to NO concentration of 10 ppb and up to 100 ppb. Shortly, these results can be beneficial in the NO breath detection for patients with chronic inflammatory airway disease, such as asthma. Full article

Thymoquinone is a natural bioactive with significant therapeutic activity against multiple ailments including wound healing. The poor aqueous solubility and low skin permeability limit its therapeutic efficacy. The present investigation aimed to improve the biopharmaceutical attributes of thymoquinone to enhance its topical efficacy in wound healing. A nanoemulsion-based hydrogel system was designed and characterized as a nanotechnology-mediated drug delivery approach to improve the therapeutic efficacy of thymoquinone, utilizing a high-energy emulsification technique. The black seed oil, as a natural home of thymoquinone, was utilized to improve the drug loading capacity of the developed nanoemulsion system and reduced the oil droplet size to <100 nm through ultrasonication. The influence of formulation composition, and the ultrasonication process conditions, were investigated on the mean globule size and polydispersity index of the generated nanoemulsion. Irrespective of surfactant/co-surfactant ratio and % concentration of surfactant/co-surfactant mixture, the ultrasonication time had a significant (p < 0.05) influence on the mean droplet size and polydispersity index of the generated nanoemulsion. The developed nanoemulgel system of thymoquinone demonstrated the pseudoplastic behavior with thixotropic properties, and this behavior is desirable for topical application. The nanoemulgel system of thymoquinone exhibited significant enhancement (p < 0.05) in skin penetrability and deposition characteristics after topical administration compared to the conventional hydrogel system. The developed nanoemulgel system of thymoquinone exhibited quicker and early healing in wounded Wistar rats compared to the conventional hydrogel of thymoquinone, while showing comparable healing efficacy with respect to marketed silver sulfadiazine (1%) cream. Furthermore, histopathology analysis of animals treated with a developed formulation system demonstrated the formation of the thick epidermal layer, papillary dermis along with the presence of extensive and organized collagen fibers in newly healed tissues. The outcome of this investigation signifies that topical delivery of thymoquinone through nanoemulgel system is a promising candidate which accelerates the process of wound healing in preclinical study. Full article

From electronic devices to large-area electronics, from individual cells to skin substitutes, printing techniques are providing compelling applications in wide-ranging fields. Research has thus fueled the vision of a hybrid, printing platform to fabricate sensors/electronics and living engineered tissues simultaneously. Following this interest, we have fabricated interdigitated-electrode sensors (IDEs) by inkjet printing to monitor epithelial cell cultures. We have fabricated IDEs using flexible substrates with silver nanoparticles as a conductive element and SU-8 as the passivation layer. Our sensors are cytocompatible, have a topography that simulates microgrooves of 300 µm width and ~4 µm depth, and can be reused for cellular studies without detrimental in the electrical performance. To test the inkjet-printed sensors and demonstrate their potential use for monitoring laboratory-growth skin tissues, we have developed a real-time system and monitored label-free proliferation, migration, and detachment of keratinocytes by impedance spectroscopy. We have found that variations in the impedance correlate linearly to cell densities initially seeded and that the main component influencing the total impedance is the isolated effect of the cell membranes. Results obtained show that impedance can track cellular migration over the surface of the sensors, exhibiting a linear relationship with the standard method of image processing. Our results provide a useful approach for non-destructive in-situ monitoring of processes related to both in vitro epidermal models and wound healing with low-cost ink-jetted sensors. This type of flexible sensor as well as the impedance method are promising for the envisioned hybrid technology of 3D-bioprinted smart skin substitutes with built-in electronics. Full article

Direct analysis of matrix and admixture elements in non-conducting crystals is a relevant analytical task in terms of quality assurance of optical materials. The current study aimed to develop a method capable to assess the inhomogeneity of optical crystals with sufficient sensitivity. K_1−xRb_xTiOPO₄ (x = 0.002 and 0.05) and KGd_1−yNd_y(WO₄)₂ (y = 0.05) were grown using the top-seeded solution growth method (TSSG). The samples were analyzed by microsecond direct current pulsed glow discharge time-of-flight mass spectrometry (µs-PDC TOF GDMS). The data were compared with the results obtained by scanning electron microscope-energy dispersive X-ray spectroscopy (SEM EDX) and spectrophotometry and validated by the analysis of certified reference material. Sample glow discharge sputtering and analysis were optimized and implemented in real samples. Sample coating with a silver layer and sample pressing in the metallic matrix were proposed to ensure effective sputtering for K_1−xRb_xTiOPO₄ and KGd_1−yNd_y(WO₄)₂, respectively. Using the designed method, the inhomogeneity of the dopant’s distribution was demonstrated along the growth axis and in the case of K_1−xRb_xTiOPO₄, also in the growth sectors of different faces. The designed method is applicable for the direct analysis of optical crystal and may be implemented in quality assurance in the manufacturing of optical materials. Full article

Dye-sensitized solar cells (DSSCs) are low-cost solar cells belonging to the thin-film photovoltaic cell type. In this study, we studied the photovoltaic performances of DSSCs based on titanium dioxide (TiO₂) nanofibers (NFs) containing silver (Ag) nanoparticles (NPs) under low illumination. We used the sol-gel method with the electrospinning technique to prepare the TiO₂ NFs containing Ag NPs. Herein, we used two ways to add TiO₂/Ag NFs to modify the photoelectrode successfully and enhance the performance of DSSCs. One way was that the TiO₂/Ag NFs were mixed with pristine TiO₂; the other way was that the TiO₂/Ag NFs were seeded beside the TiO₂ colloid layer as an additional layer on the photoelectrode of the DSSC. According to this experiment, the photovoltaic conversion efficiency of the DSSC which had TiO₂/Ag NF seeded as an additional layer on the photoelectrode (5.13%) was increased by 28% compared to the DSSC without the photoelectrode modification (3.99%). This was due to the suppression of electron recombination and the more effective utilization of the light radiation by adding the TiO₂/Ag NFs. Because of the good conductivity of Ag, the electrons were quickly transported and electron recombination was reduced. In addition, the photovoltaic conversion efficiency of the DSSC which had TiO₂/Ag NF seeded as an additional layer on the photoelectrode increased from 5.13% to 6.23% during the decrease in illumination from 100 mW/cm² to 30 mW/cm²; however, its photovoltaic conversion efficiency decreased to 5.31% when the illumination was lowered to 10 mW/cm². Full article