Search Results (464)

In the final phases of casing production, shale gas horizontal wells with a downward slope frequently find it difficult to sustain self-flow production. The ideal tubing insertion depth for self-flow production in gas wells has not been thoroughly studied, even though the timely adoption of tubing production can successfully prolong the self-flow production period. Using a fully dynamic multiphase flow simulation program, the ideal tubing depth for gas well self-flow production was ascertained. A wellbore structural model was built using a particular well as an example. By altering the tubing depth, the formation pressure limit values necessary to sustain gas well self-flow production at various tubing depths were simulated. The appropriate tubing depth for gas well self-flow production was examined, along with the well’s cumulative gas output at various tubing depths. Using the example as a case study, it was discovered that the critical formation pressure for gas well self-flowing production dropped to 7.8 MPa when the tubing was lowered to 2600 m. This effectively increased cumulative production by 56.19 × 10⁶ m³ and extended the self-flow production time by roughly 135 days. The study’s findings offer strong evidence in favor of maximizing shale gas wells’ self-flow production performance in later phases of production. Full article

The persistent challenge of fracture-driven interference (FDI) during large-scale hydraulic fracturing in the southern Sichuan Basin has severely compromised shale gas productivity, while the existing research has inadequately addressed both FDI risk reductions and the optimization of reservoir stimulation. To bridge this gap, this study developed a mechanistic model of the competitive multi-cluster fracture propagation under non-uniform perforation conditions and established a perforation-based design methodology for the mitigation of horizontal well interference. The results demonstrate that spindle-shaped perforations enhance the uniformity of fracture propagation by 20.3% and 35.1% compared to that under uniform and trapezoidal perforations, respectively, with the perforation quantity (48) and diameter (10 mm) identified as the dominant control parameters for balancing multi-cluster growth. Through a systematic evaluation of the fracture communication mechanisms, three distinct inter-well types of FDI were identified: Type I (natural fracture–stress anisotropy synergy), Type II (natural-fracture-dominated), and Type III (stress-anisotropy-dominated). To mitigate these, customized perforation schemes coupled with geometry-optimized fracture layouts were developed. The surveillance data for the offset well show that the pressure interference decreased from 14.95 MPa and 6.23 MPa before its application to 0.7 MPa and 0 MPa, achieving an approximately 95.3% reduction in the pressure interference in the application wells. The expansion morphology of the inter-well fractures confirmed effective fluid redistribution across clusters and containment of the overextension of planar fractures, demonstrating this methodology’s dual capability to enhance the effectiveness of stimulation while resolving FDI challenges in deep shale reservoirs, thereby advancing both productivity and operational sustainability in complex fracturing operations. Full article

The Silurian marine shale in the Sichuan Basin is currently the main reservoir for shale gas reserves and production in China. This study investigates the reservoir evolution of the Silurian marine shale based on fractal dimension, quantifying the complexity and heterogeneity of the shale’s pore structure. Physical simulation experiments were conducted on field-collected shale samples, revealing the evolution of total organic carbon, mineral composition, porosity, and micro-fractures. The fractal dimension of shale pore was characterized using the Frenkel–Halsey–Hill and capillary bundle models. The relationships among shale components, porosity, and fractal dimensions were investigated through a correlation analysis and a principal component analysis. A comprehensive evolution model for porosity and micro-fractures was established. The evolution of mineral composition indicates a gradual increase in quartz content, accompanied by a decline in clay, feldspar, and carbonate minerals. The thermal evolution of organic matter is characterized by the formation of organic pores and shrinkage fractures on the surface of kerogen. Retained hydrocarbons undergo cracking in the late stages of thermal evolution, resulting in the formation of numerous nanometer-scale organic pores. The evolution of inorganic minerals is represented by compaction, dissolution, and the transformation of clay minerals. Throughout the simulation, porosity evolution exhibited distinct stages of rapid decline, notable increase, and relative stabilization. Both pore volume and specific surface area exhibit a trend of decreasing initially and then increasing during thermal evolution. However, pore volume slowly decreases after reaching its peak in the late overmature stage. Fractal dimensions derived from the Frenkel–Halsey–Hill model indicate that the surface roughness of pores (D1) in organic-rich shale is generally lower than the complexity of their internal structures (D2) across different maturity levels. Additionally, the average fractal dimension calculated based on the capillary bundle model is higher, suggesting that larger pores exhibit more complex structures. The correlation matrix indicates a co-evolution relationship between shale components and pore structure. Principal component analysis results show a close relationship between the porosity of inorganic pores, microfractures, and fractal dimension D2. The porosity of organic pores, the pore volume and specific surface area of the main pore size are closely related to fractal dimension D1. D1 serves as an indicator of pore development extent and characterizes the changes in components that are “consumed” or “generated” during the evolution process. Based on mineral composition, fractal dimensions, and pore structure evolution, a comprehensive model describing the evolution of pores and fractal dimensions in organic-rich shale was established. Full article

Against the backdrop of global energy transition and strict environmental regulations, supercritical carbon dioxide (scCO₂) fracturing and oil displacement technologies have emerged as pivotal green approaches in shale gas exploitation, offering the dual advantages of zero water consumption and carbon sequestration. However, the inherent low viscosity of scCO₂ severely restricts its sand-carrying capacity, fracture propagation efficiency, and oil recovery rate, necessitating the urgent development of high-performance thickeners. The current research on scCO₂ thickeners faces a critical trade-off: traditional fluorinated polymers exhibit excellent philicity CO₂, but suffer from high costs and environmental hazards, while non-fluorinated systems often struggle to balance solubility and thickening performance. The development of new thickeners primarily involves two directions. On one hand, efforts focus on modifying non-fluorinated polymers, driven by environmental protection needs—traditional fluorinated thickeners may cause environmental pollution, and improving non-fluorinated polymers can maintain good thickening performance while reducing environmental impacts. On the other hand, there is a commitment to developing non-noble metal-catalyzed siloxane modification and synthesis processes, aiming to enhance the technical and economic feasibility of scCO₂ thickeners. Compared with noble metal catalysts like platinum, non-noble metal catalysts can reduce production costs, making the synthesis process more economically viable for large-scale industrial applications. These studies are crucial for promoting the practical application of scCO₂ technology in unconventional oil and gas development, including improving fracturing efficiency and oil displacement efficiency, and providing new technical support for the sustainable development of the energy industry. This study innovatively designed an amphiphilic modified amino silicone oil polymer (MA-co-MPEGA-AS) by combining maleic anhydride (MA), methoxy polyethylene glycol acrylate (MPEGA), and amino silicone oil (AS) through a molecular bridge strategy. The synthesis process involved three key steps: radical polymerization of MA and MPEGA, amidation with AS, and in situ network formation. Fourier transform infrared spectroscopy (FT-IR) confirmed the successful introduction of ether-based CO₂-philic groups. Rheological tests conducted under scCO₂ conditions demonstrated a 114-fold increase in viscosity for MA-co-MPEGA-AS. Mechanistic studies revealed that the ether oxygen atoms (Lewis base) in MPEGA formed dipole–quadrupole interactions with CO₂ (Lewis acid), enhancing solubility by 47%. Simultaneously, the self-assembly of siloxane chains into a three-dimensional network suppressed interlayer sliding in scCO₂ and maintained over 90% viscosity retention at 80 °C. This fluorine-free design eliminates the need for platinum-based catalysts and reduces production costs compared to fluorinated polymers. The hierarchical interactions (coordination bonds and hydrogen bonds) within the system provide a novel synthetic paradigm for scCO₂ thickeners. This research lays the foundation for green CO₂-based energy extraction technologies. Full article

Currently, the Longmaxi shale in the Sichuan Basin is the most successful stratum of shale gas production in China. However, because Longmaxi shale mostly has high over-maturity, a low-maturity sample cannot be obtained for gas generation thermal simulations, and as a result, a gas generation model has not yet been established for it. Therefore, models of other shales are usually used to calculate the amount of gas generated from Longmaxi shale, but they may produce inaccurate results. In this study, a Longmaxi shale sample with an equivalent vitrinite reflectance calculated from Raman spectroscopy (EqVR_o) of 1.26% was obtained from Well Yucan 1 in the Chengkou area, northeast Sichuan Province. This Longmaxi shale may have the lowest maturity in nature. Pyrolysis simulations based on gold tubes were performed on this sample, and the gas generation line was obtained. The amount of gas generated during the low-maturity stage was compensated by referring to gas generation data obtained from Lower Silurian black shale in western Lithuania. Thus, a gas generation model of the Longmaxi shale was built. The model showed that the gas generation process of Longmaxi shale could be divided into three stages: (1) First, there is the quick generation stage (EqVR_o 0.5–3.0%), where hydrocarbon gases were generated quickly and constantly, and the generation rate was steady. A maximum of 458 mL/g TOC was reached at a maturity of 3.0% EqVR_o. (2) Second, there is the stable stage (EqVR_o 3.0–3.25%), where the amount of generated gas reached a plateau of 453–458 mL/g TOC. (3) Third, there is the rapid descent stage (EqVR_o > 3.25%), where the amount of generated gas started to decrease, and it was 393 mL/g TOC at an EqVR_o of 3.34%. This model allows us to more accurately calculate the amount of gas generated from the Longmaxi shale in the Sichuan Basin. Full article

The gas-production potential of shale gas is a comprehensive evaluation metric that assesses the reservoir quality, gas-content properties, and gas-production capacity. Currently, the evaluation of gas-production potential is generally conducted through qualitative comparisons of relevant parameters, which can lead to multiple solutions and make it difficult to establish a comprehensive evaluation index. This paper introduces a gas-production potential evaluation method based on the Analytic Hierarchy Process (AHP). It uses judgment matrices to analyze key parameters such as gas content, brittleness index, total organic carbon content, the length of high-quality gas-layer horizontal sections, porosity, gas saturation, formation pressure, and formation density. By integrating fuzzy mathematics, a mathematical model for gas-production potential is established, and corresponding gas-production levels are defined. The model categorizes gas-production potential into four levels: when the gas-production index exceeds 0.65, it is classified as a super-high-production well; when the gas-production index is between 0.45 and 0.65, it is classified as a high-production well; when the gas-production index is between 0.35 and 0.45, it is classified as a medium-production well; and when the gas-production index is below 0.35, it is classified as a low-production well. Field applications have shown that this model can accurately predict the gas-production potential of shale gas wells, showing a strong correlation with the unobstructed flow rate of gas wells, and demonstrating broad applicability. Full article

In the global energy sector, water-bearing reservoir-typed gas storage accounts for about 30% of underground gas storage (UGS) reservoirs and is vital for natural gas storage, balancing gas consumption, and ensuring energy supply stability. However, when constructing the UGS in the M gas reservoir, selecting suitable areas poses a challenge due to the complicated gas–water distribution in the multi-layered water-bearing gas reservoir with a long production history. To address this issue and enhance energy storage efficiency, this study presents an integrated geomechanical-hydraulic assessment framework for choosing optimal UGS construction horizons in multi-layered water-bearing gas reservoirs. The horizons and sub-layers of the gas reservoir have been quantitatively assessed to filter out the favorable areas, considering both aspects of geological characteristics and production dynamics. Geologically, caprock-sealing capacity was assessed via rock properties, Shale Gouge Ratio (SGR), and transect breakthrough pressure. Dynamically, water invasion characteristics and the water–gas distribution pattern were analyzed. Based on both geological and dynamic assessment results, the favorable layers for UGS construction were selected. Then, a compositional numerical model was established to digitally simulate and validate the feasibility of constructing and operating the M UGS in the target layers. The results indicated the following: (1) The selected area has an SGR greater than 50%, and the caprock has a continuous lateral distribution with a thickness range from 53 to 78 m and a permeability of less than 0.05 mD. Within the operational pressure ranging from 8 MPa to 12.8 MPa, the mechanical properties of the caprock shale had no obvious changes after 1000 fatigue cycles, which demonstrated the good sealing capacity of the caprock. (2) The main water-producing formations were identified, and the sub-layers with inactive edge water and low levels of water intrusion were selected. After the comprehensive analysis, the I-2 and I-6 sub-layer in the M 8 block and M 14 block were selected as the target layers. The numerical simulation results indicated an effective working gas volume of 263 million cubic meters, demonstrating the significant potential of these layers for UGS construction and their positive impact on energy storage capacity and supply stability. Full article

A novel externally heated retort for Jimsar oil shale resources is proposed, and the symmetrical mathematical model of the transport process in the retort is established through intensively studying the mechanisms of shale gas flows, heat transfer, and pyrolysis reactions in the retort. The descriptions of axial and radial movements and temperature of oil shale and gases, and the distribution of pyrolysis reaction and yielding of gaseous products and semi-coke in various regions of the retort are simulated. The results show that oil shale can pyrolyze gradually from the region near the wall to the core region of the retorting chamber and pyrolyze completely at the bottom of the retorting zone through receiving the heat flux transferring from the combustion channels. The final pyrolysis temperature of oil shale is 821.05 K, and the outlet temperature of semi-coke cooled by cold recycled gas is 676.35 K, which are in agreement with the design requirements. In total, 75 toil shales can be retorted in one retorting chamber per day, and the productivity of the retort can be increased by increasing the number of retorting chambers. The fuel self-sufficiency rate of this externally heated oil shale retort can reach 82.83%. Full article

Anthropogenic CO₂ emissions are a major driver of climate change, highlighting the urgent need for effective mitigation strategies. Carbon Capture, Utilization, and Storage (CCUS) offers a promising approach, particularly through CO₂-enhanced gas recovery (EGR) in shale reservoirs, which enables simultaneous hydrocarbon production and CO₂ sequestration. This study employs a numerical simulation model to compare two injection strategies: CO₂ flooding and huff-and-puff (H&P). The results indicate that, without accounting for key mechanisms such as adsorption and molecular diffusion, CO₂ H&P provides minimal improvement in methane recovery. When adsorption is included, methane recovery increases by 9%, with 14% of the injected CO₂ stored over 40 years. Incorporating diffusion enhances recovery by 19%, although with limited storage potential. In contrast, CO₂ flooding improves methane production by 26% and retains up to 94% of the injected CO₂. Higher storage efficiency is observed in reservoirs with high porosity and low permeability, particularly in nano-scale pore systems. Overall, CO₂ H&P may be a viable EGR option when adsorption and diffusion are considered, while CO₂ flooding demonstrates greater effectiveness for both enhanced gas recovery and long-term CO₂ storage in shale formations. Full article

Numerous uncertainties persist regarding the differential enrichment mechanisms of shale gas reservoirs in southern China. This investigation systematically examines the sedimentary environments and reservoir characteristics of the Wufeng–Longmaxi formations in the Changning area of the Sichuan Basin, through the integration of comprehensive drilling data, core samples, and analytical measurements. Multivariate sedimentary proxies (including redox conditions, terrigenous detrital influx, basinal water restriction, paleoclimatic parameters, paleowater depth variations, and paleo-marine productivity) were employed to elucidate environmental controls on reservoir development. The research findings demonstrate that during the depositional period of the Wufeng Formation in the Changning area, the bottom water was characterized by suboxic to anoxic conditions under a warm-humid paleoclimate, with limited terrigenous detrital input and strong water column restriction throughout the interval. Within the Longmaxi Formation, the depositional environment evolved from intensely anoxic conditions in the LM1 through suboxic states in the LM3 interval, approaching toxic conditions by the LM2 depositional phase. Concurrently, the paleoclimate transitioned towards warmer and more humid conditions, accompanied by progressively intensified terrigenous input from the LM1-LM6, while maintaining semi-restricted water circulation. Both paleowater depth and paleoproductivity peaked from the Wufeng Formation to the LM1 interval, followed by gradual shallowing of water depth and declining productivity during the LM3–LM6 depositional phases. Comparative analysis of depositional environments and reservoir characteristics reveals that sedimentary conditions exert a controlling influence on multiple reservoir parameters, including shale mineral composition, organic matter enrichment, pore architecture, petrophysical properties (e.g., porosity, permeability), and gas-bearing potential. Full article

Transitional shale gas represents a critical frontier for China’s oil and gas exploration, characterized by extensive distribution and substantial resource potential. However, its frequent interbedding with coal seams and tight sandstones results in a complex reservoir architecture, significantly increasing extraction challenges. Hydraulic fracturing remains the primary method for effectively stimulating production in such reservoirs. Nevertheless, due to the complex stacking patterns of coal, shale, and tight sandstone layers, fracturing often generates complex fracture networks, leading to pronounced stress-sensitive effects and fracture interference during production. Moreover, the development of transitional shale gas reservoirs typically employs multi-well pad fracturing (“factory-mode” drilling) with tight well spacing, intensifying the well interference and its impact on well group productivity. These factors collectively complicate post-fracturing production forecasting. Existing productivity models predominantly focus on single-lithology reservoirs with idealized fracture networks, neglecting critical factors such as the fracture interference, well interference, and stress sensitivity. To address this gap, this study targets the Ordos Basin’s transitional shale gas reservoirs. By integrating the multi-lithology, multi-layer stacked reservoir characteristics, we developed a productivity model for infill wells in such reservoirs. Using a semi-analytical approach, we analyzed post-fracturing production behavior in horizontal wells, optimized key development parameters, and provided a scientific basis for the efficient development of these reservoirs. Full article

Coalbed methane (CBM), a significant unconventional natural gas resource, holds a crucial position in China’s ongoing energy structure transformation. However, the inherent low permeability, high brittleness, and strong sensitivity of CBM reservoirs to drilling fluids often lead to severe formation damage during drilling operations, consequently impairing well productivity. To address these challenges, this study developed a novel low-damage, plugging, and anti-collapse water-based drilling fluid gel system (ACWD) specifically designed for coalbed methane drilling. Laboratory investigations demonstrate that the ACWD system exhibits superior overall performance. It exhibits stable rheological properties, with an initial API filtrate loss of 1.0 mL and a high-temperature, high-pressure (HTHP) filtrate loss of 4.4 mL after 16 h of hot rolling at 120 °C. It also demonstrates excellent static settling stability. The system effectively inhibits the hydration and swelling of clay and coal, significantly reducing the linear expansion of bentonite from 5.42 mm (in deionized water) to 1.05 mm, and achieving high shale rolling recovery rates (both exceeding 80%). Crucially, the ACWD system exhibits exceptional plugging performance, completely sealing simulated 400 µm fractures with zero filtrate loss at 5 MPa pressure. It also significantly reduces core damage, with an LS-C1 core damage rate of 7.73%, substantially lower than the 19.85% recorded for the control polymer system (LS-C2 core). Field application in the JX-1 well of the Ordos Basin further validated the system’s effectiveness in mitigating fluid loss, preventing wellbore instability, and enhancing drilling efficiency in complex coal formations. This study offers a promising, relatively environmentally friendly, and cost-effective drilling fluid solution for the safe and efficient development of coalbed methane resources. Full article

Shale plays with pre-existing natural fractures can yield significant production when operating horizontal wells with multi-stage hydraulic fracturing (HWMHF). This work proposes a general, robust, and integrated framework for estimating optimal HWMHF design parameters in an unconventional naturally fractured oil reservoir. This work considers uncertainty in both the distribution of the natural fractures and uncertainty in three geo-mechanical parameters: the internal friction factor, the cohesion coefficient, and the tensile strength. Because a maximum of five design variables is considered, it is appropriate to apply derivative-free algorithms. This work considers versions of the genetic algorithm (GA), particle swarm optimization (PSO), and general pattern search (GPS) algorithms. The forward model consists of two linked software programs: a geo-mechanical simulator and an unconventional shale oil simulator. The two simulators run sequentially during the optimization process without human intervention. The in-house geo-mechanical simulator model provides sufficient computational efficiency so that it is feasible to solve the robust optimization problem. An embedded discrete fracture model (EDFM) is implemented to model large-scale fractures. Two cases strongly verified the feasibility of the framework for the optimization of HWMHF, and the average comprehensive NPV increases by 35% and 102.4%, respectively. By comparison, the pattern search algorithm is more suitable for HWMHF optimization. In this way, oil and gas scientists are contributing to the energy industry more accurately and resolutely. Full article

In the production process of horizontal wells, wellbore temperature data play a critical role in predicting shale gas production. This study proposes a coupled thermo-hydro-mechanical (THM) mathematical model that accounts for the influence of the stress field when determining the distribution of wellbore temperature. The model integrates the effects of heat transfer in the temperature field, gas transport in the seepage field, and the mechanical deformation of shale induced by the stress field. The coupled model is solved using the finite difference method. The model was validated against field data from shale gas production, and sensitivity analyses were conducted on seven key parameters related to the stress field. The findings indicate that the stress field exerts an influence on both the wellbore temperature distribution and the total gas production. Neglecting the stress field effects may lead to an overestimation of shale gas production by up to 12.9%. Further analysis reveals that reservoir porosity and Langmuir volume are positively correlated with wellbore temperature, while permeability, Young’s modulus, Langmuir pressure, the coefficient of thermal expansion, and adsorption strain are negatively correlated with wellbore temperature. Full article

Current models of sedimentary environments and organic matter (OM) enrichment for the Lower Cambrian black shales in the Yangtze Platform have not yet incorporated its northern carbonate platform margin where the related research is lacked. This study focuses on the SNZ1 well in the northern carbonate platform margin, utilizing total organic carbon (TOC) content and major and trace element data to reveal the main controlling factors of OM enrichment during the Early Cambrian. The results show that the shale stratum is tentatively ascribed to the Lower Cambrian Stage 3 and that, during its deposition, the redox transitioned from anoxic to suboxic–oxic conditions, the hydrodynamic conditions weakened initially and then strengthened, the primary productivity first increased and then decreased, the paleoclimate shifted from arid–cold to warm–humid conditions, and the terrigenous clastic input gradually diminished. Overall, the OM enrichment is primarily controlled by preservation conditions. By systematically analyzing the data from the intraplatform basin to the deep-sea basin across the Yangtze Block, a model of the sedimentary environments and OM enrichment during the Early Cambrian was suggested. Additionally, this study highlights the intrinsic link between the expansion of oxygenated surface water and the Cambrian explosion. These results provide critical insights for shale gas exploration in this region. Full article