Search Results (878)

This study proposes a CatBoost-enhanced hyperspectral modeling approach for accurate prediction of wood dyeing formulations. Using Pinus sylvestris var. mongolica veneer as the substrate, 306 samples with gradient dye concentrations were prepared, and their reflectance spectra (400–700 nm) were acquired. After noise reduction and sensitive band selection (400–450 nm, 550–600 nm, and 600–650 nm), spectral descriptors were extracted as model inputs. The CatBoost algorithm, optimized via k-fold cross-validation and grid search, outperformed XGBoost, random forest, and SVR in prediction accuracy, achieving MSE = 0.00271 and MAE = 0.0349. Scanning electron microscopy (SEM) revealed the correlation between dye particle distribution and spectral response, validating the model’s physical basis. This approach enables intelligent dye formulation control in industrial wood processing, reducing color deviation (ΔE < 1.75) and dye waste by approximately 25%. Full article

Pinus massoniana Lamb. is an economically important conifer native to China. However, it is highly susceptible to the pine wood nematode (Bursaphelenchus xylophilus, PWN), the causal agent of pine wilt disease (PWD), resulting in substantial ecological and economic losses. To elucidate potential molecular defense mechanisms, 50 NAC (NAM, ATAF1/2, and CUC2) transcription factors (PmNACs) were identified in the P. massoniana genome. Phylogenetic analysis divided these PmNACs into seven subfamilies, and motif analysis identified ten conserved motifs associated with stress responses. Twenty-three genes were selected for expression analysis in various tissues and under exogenous salicylic acid (SA), methyl jasmonate (MeJA), and PWN infection. Six genes (PmNAC1, PmNAC8, PmNAC9, PmNAC17, PmNAC18, and PmNAC20) were significantly up-regulated by both hormonal treatment and PWN infection, implying their involvement in JA/SA-mediated immune pathways. Functional characterization showed PmNAC8 is a nuclear-localized transcription factor with autoactivation activity. Furthermore, transient overexpression of PmNAC8 in Nicotiana benthamiana induced reactive oxygen species (ROS) accumulation and necrotic lesions. Collectively, these results elucidate NAC-mediated defense responses to PWN infection in P. massoniana and identify candidate genes for developing PWD-resistant pine varieties. Full article

Climate extremes threaten the resilience of Eucalyptus plantations, yet hybridization with drought-tolerant species may enhance stress tolerance. This study analyzed xylem anatomical and functional drought responses in commercial Eucalyptus grandis (GG) clones and hybrids: E. grandis × camaldulensis (GC), E. grandis × tereticornis (GT), and E. grandis × urophylla (GU1, GU2). We evaluated vessel traits (water transport), fibers (mechanical support), and wood density (D) in stems and branches. Theoretical stem hydraulic conductivity (k_Stheo), vessel lumen fraction (F), vessel composition (S), and associations with previous hydraulic and growth data were assessed. While general drought responses occurred, GC had the most distinct xylem profile. This may explain it having the highest performance in different irrigation conditions. Red gum hybrids (GC, GT) maintained k_Stheo under drought, with stable F and a narrower vessel size, especially in branches. Conversely, GG and GU2 reduced F and S; and stem k_Stheo declined for a similar F in these clones, indicating vascular reconfiguration aligning the stem with the branch xylem. Almost all clones increased D under drought in any organ, with the highest increase in red gum hybrids. These results reveal diverse anatomical adjustments to drought among clones, partially explaining their growth responses. Full article

With the growing severity of environmental pollution, people are paying increasing attention to their health. However, naturally occurring wood with health benefits and applications in human healthcare is still scarce. Natural wood exhibits a limited negative oxygen ion release capacity, and this release has a short duration, failing to meet practical application requirements. This study innovatively developed a humidity-responsive, healthy wood material with a high negative oxygen ion release capacity based on fast-growing poplar. Through vacuum cyclic impregnation technology, hexagonal stone powder was infused into the pores of poplar wood, endowing it with the ability to continuously release negative oxygen ions. The healthy wood demonstrated a static average negative oxygen ion release rate of 537 ions/cm³ (peaking at 617 ions/cm³) and a dynamic average release rate of 3,170 ions/cm³ (peaking at 10,590 ions/cm³). The results showed that the particle size of hexagonal stone powder in suspension was influenced by the dispersants and dispersion processes. The composite dispersion process demonstrated optimal performance when using 0.5 wt% silane coupling agent γ-(methacryloxy)propyltrimethoxysilane (KH570), achieving the smallest particle size of 8.93 μm. The healthy wood demonstrated excellent impregnation performance, with a weight gain exceeding 14.61% and a liquid absorption rate surpassing 165.18%. The optimal impregnation cycle for vacuum circulation technology was determined to be six cycles, regardless of the type of dispersant. Compared with poplar wood, the hygroscopic swelling rate of healthy wood was lower, especially in PEG-treated samples, where the tangential, radial, longitudinal, and volumetric swelling rates decreased by 70.93%, 71.67%, 69.41%, and 71.35%, respectively. Combining hexagonal stone powder with fast-growing poplar wood can effectively enhance the release of negative oxygen ions. The static average release of negative oxygen ions from healthy wood is 1.44 times that of untreated hexagonal stone powder, and the dynamic release reaches 2 to 3 times the concentration of negative oxygen ions specified by national fresh air standards. The water-responsive mechanism revealed that negative oxygen ion release surged when ambient humidity exceeded 70%. This work proposes a sustainable and effective method to prepare healthy wood with permanent negative oxygen ion release capability. It demonstrates great potential for improving indoor air quality and enhancing human health. Full article

While boreal forests constitute 30% of the Earth’s forested area and are responsible for 20% of the global carbon sink, there is considerable concern about their sustainability. This paper focuses on the role of elevated CO₂, examining whether wood volume in these forests has responded to increased CO₂ over the last 60 years. To accomplish this, we use a rich set of wood volume measurement data from the Province of Alberta, Canada, and deploy quasi-experimental techniques to determine the effect of elevated CO₂. While the few experimental studies that have examined boreal forests have found almost no effect of elevated CO₂, our results indicate that a 1.0% increase in lifetime exposure to CO₂ leads to a 1.1% increase in aboveground wood volume in these boreal forests. This study showcases the value of research designs that use natural settings to better account for the effects of prolonged exposure to elevated CO₂. Our results should enable improved delineation of the drivers of historical changes in wood volume and carbon storage in boreal forests. In addition, when combined with other studies, these results will likely aid policymakers in designing management or policy approaches that will enhance the sustainability of forests in boreal regions. Full article

Quercus faginea Lam., a winter-deciduous oak native to the Iberian Peninsula, typically grows under a Mediterranean climate. To identify the main drivers influencing radial wood increment, we analyzed the climatic signals in tree-ring width and wood anatomical traits using increment cores. Winter conditions influenced both latewood width and earlywood vessel size in the first row. Latewood was positively correlated with precipitation and temperature, with the long-term positive effect of winter water supply supported by SPEI. In contrast, vessel size showed negative correlations, also reflecting a long-term negative effect of winter precipitation. Consequently, conditions that enhanced latewood width and overall tree-ring growth appear to be associated with the formation of smaller earlywood vessels. Although ample winter precipitation replenishes soil water reserves and supports prolonged wood formation, it may also induce anaerobic soil conditions that promote root fermentation, depleting carbohydrates needed for cell turgor and expansion, and ultimately regulating earlywood vessel size. This physiological decoupling may help explain the lack of a significant correlation between latewood width and earlywood vessel size, underscoring their independent responses to environmental influences. Our findings highlighted the complex interplay between various climatic conditions affecting Q. faginea, with implications for understanding its adaptive capacity in changing climates. Full article

Industrial building renovation is a sustainable strategy to preserve urban heritage while meeting modern needs. However, how interior material scenes affect users’ emotions, thermal perception, and functional preferences remains underexplored in adaptive reuse contexts. This study used virtual reality (VR) to examine four common material scenes—wood, concrete, red brick, and white-painted surfaces—within industrial renovation settings. A total of 159 participants experienced four Lumion-rendered VR environments and rated them on thermal perception (visual warmth, thermal sensation, comfort), emotional response (arousal, pleasure, restoration), and functional preference. Data were analyzed using repeated measures ANOVA and Pearson correlation. Wood and red brick scenes were associated with warm visuals; wood scenes received the highest ratings for thermal comfort and pleasure, white-painted scenes for restoration and arousal, and concrete scenes, the lowest scores overall. Functional preferences varied by space: white-painted and concrete scenes were most preferred in study/work settings, wood in social spaces, wood and red brick in rest areas, and concrete in exhibition spaces. By isolating material variables in VR, this study offers a novel empirical approach and practical guidance for material selection in adaptive reuse to enhance user comfort, emotional well-being, and spatial functionality in industrial heritage renovations. Full article

Anoplophora glabripennis, is one of the most devastating wood borers of many broad leaf trees. Our previous results indicated that antennae of A. glabripennis showed electroantennogram (EAG) responses to several host plant volatiles. However, the quantities of active compounds necessary to trigger an EAG response remains unclear. To relate EAG responses with quantities of active molecules, we quantified the level of molecular triggering in the EAG response of A. glabripennis by a series of procedures. First, we used the EAG apparatus to measure EAG responses of A. glabripennis to five concentrations of eight chemicals and obtained dose–response curves. Second, volatiles released after blowing air over filter paper loaded with volatiles for different numbers of times (purging) were collected by solid-phase microextraction (SPME) and quantified by gas chromatography (GC), so we obtained the quantity of chemical released from each purge; the minimum number of molecules in each purge in the EAG was calculated by the molar mass for different compounds. For instance, the number of molecules of (Z)-3-hexenol reaching the female antennal segment in EAG was 8.68 × 10⁸ at 0.01 ng/μL concentration, and 1.39 × 10⁵ at 0.01 mV potential value. Finally, by comparing sensilla numbers on tested antennal segments with the entire antennae, the minimum number of molecules, or molecular flow, of tested compounds required to elicit an electrophysiological response from two antennae of ALB could be estimated either at a minimum concentration (2.49 × 10⁸ at 0.01 ng/μL concentration of (Z)-3-Hexenol, for female) or at a minimum potentiometric response value (3.99 × 10⁴ at 0.01 mV potential value). Full article

Rammed earth (RE), a traditional material aligned with circular economy (CE) principles, has been gaining renewed interest in contemporary construction due to its low environmental impact and compatibility with sustainable building strategies. Though not a modern invention, it is being reintroduced in response to the increasingly strict European Union (EU) regulations on carbon footprint, life cycle performance, and thermal efficiency. RE walls offer multiple benefits, including humidity regulation, thermal mass, plasticity, and structural strength. This study also draws attention to their often-overlooked ability to mitigate indoor overheating. To preserve these advantages while enhancing thermal performance, this study explores insulation strategies that maintain the vapor-permeable nature of RE walls. A parametric analysis using Delphin 6.1 software was conducted to simulate heat and moisture transfer in two main configurations: (a) a ventilated system insulated with mineral wool (MW), wood wool (WW), hemp shives (HS), and cellulose fiber (CF), protected by a jute mat wind barrier and finished with wooden cladding; (b) a closed system using MW and WW panels finished with lime plaster. In both cases, clay plaster was applied on the interior side. The results reveal distinct hygrothermal behavior among the insulation types and confirm the potential of natural, low-processed materials to support thermal comfort, moisture buffering, and the alignment with CE objectives in energy-efficient construction. Full article

Wood, as a natural material that stores carbon, is gaining increasing attention and has potential for use in interior architectural applications. Given the long indoor stay time characteristic of modern society, it is important to scientifically understand the effects of indoor wood application on the occupants. In this study, three residential buildings with an identical area and structure were constructed with different degrees of wood coverage (0%, 45%, 90%) using Larix kaempferi. Subsequently, indoor air quality (IAQ) evaluations and relative humidity measurements were conducted to assess the physical and chemical changes in each environment. The IAQ in wooden and non-wooden environments met the recommended IAQ standards established in South Korea. The results of the 8-month observation showed that, the higher the wood coverage ratio, the more the indoor humidity fluctuations were alleviated, and, in the case of the 90% wood coverage ratio condition, the humidity was maintained 5.2% lower in the summer and 10.9% higher in the winter compared to the 0% condition. To further assess the physiological responses induced by the wooden environment, the heart rate variability (HRV) was measured and compared for 26 participants exposed to each environment for two hours. In environments with a 0% and 90% degree of wood coverage, no statistically significant differences were found in the participants’ HRV indicators. But, in the group exposed to the 45% wooden environment, the results showed an increase in HRV indicators, natural logarithm of high frequency power (lnHF): 4.87 → 5.40 (p < 0.05), and standard deviation of normal-to-normal intervals (SDNN): 30.57 → 38.48 (p < 0.05), which are known indicators of parasympathetic nervous system activation. Full article

This research aimed to evaluate the biological resistance to xylophagous organisms and the dimensional stability related to water absorption in plastic wood panels manufactured by compression molding and produced with pine wood and recycled thermoplastics. The wood–plastic composites (WPCs) were prepared from 50% pine sawdust and 50% recycled plastics (polyethylene terephthalate-PET, high-density polyethylene-HDPE, and polypropylene-PP). The thickness swelling test was carried out by immersing of the WPC samples in water at room temperature (25–30 °C) and evaluating the total change in WPC thickness after 1500 h (≈9 weeks or two months). In addition, the coefficient of initial swelling was evaluated to verify the variability of the swelling. For the biological resistance evaluation of the WPCs, tests were carried out with soil or arboreal termites (Nasutitermes corniger) and drywood termites (Cryptotermes brevis). The WPC loss of mass and termite mortality were evaluated. The use of PP promoted the best response to thickness swelling. The simple mathematical model adopted offers real predictions to evaluate the thickness of the swelling of the compounds in a given time. For some variables there were no statistical differences. It was shown that treatment 3 (T3) presented visual damage values between 0.4 for drywood termites and 9.4 for soil termites, in addition to 26% termite mortality, represented by the lowest survival time of 12 days. The developed treatments have resistance to termite attacks; these properties can be an important starting point for its use on a larger scale by the panel industries. Full article

Thermal modification applies to a technique for the enhancement of biological durability, stability, and appearance of wood. Much is known about its effects on the chemical and physical attributes of wood. However, there is a knowledge gap concerning the effects of heat treatment on surface coating performance of different wood species. The focus of this research is heat treatment regulation of 160 °C, 180 °C, and 200 °C for three commercially important wood species which are Populus (poplar), Quercus (oak), and Pinus (pine). These treatments were evaluated in relation to coating performance indicators adhesion, integrity, and visual stability during and after natural and artificial weathering. It was revealed that specific responses among species differences exist. Populus behaved differently and exhibited a steady loss in mass and volume. Quercus demonstrated gradual degradation alongside enhanced lignin stability. Pinus exhibited maintenance of volume and mass until 180 °C after which accelerated degradation was observed. Coating durability and adhesion exhibited dependence on thermal condition, wood species, porosity, surface chemistry and microstructural variations that occurred. The research results can be used to streamline finishing processes for thermally modified wood while underscoring the critical nature of precise treatment parameter adjustments guided by species-specific responses to ensure long-term stability. Full article

Methods for the improvement of regional lignocellulosic resources (wood and agriculture waste) were studied and analyzed using blends with optimized compositions and a selective pretreatment of the blends using microwaves to enhance their thermochemical conversion and energy production efficiency. A batch-size pilot device was used to provide the thermochemical conversion of biomass blends of different compositions, analyzing the synergy of the effects of thermal and chemical interaction between the components on the yield and thermochemical conversion of volatiles, responsible for producing heat energy at various stages of flame formation. To control the thermal decomposition of the biomass, improving the flame characteristics and the produced heat, a selective pretreatment of blends using microwaves (2.45 GHz) was achieved by varying the temperature of microwave pretreatment. Assessing correlations between changes in the main characteristics of pretreated blends (elemental composition and heating value) on the produced heat and composition of products suggests that selective MW pretreatment of biomass blends activates synergistic effects of thermal and chemical interaction, enhancing the yield and combustion of volatiles with a correlating increase in produced heat energy, thus promoting the wider use of renewable biomass resources for sustainable energy production by limiting the use of fossil fuels for heat-energy production and the formation of GHG emissions. Full article

The aim of the study was to determine the relationship between selected features of wood and the surface properties after sanding operations. Woods presenting different anatomical structures, i.e., ring-porous hardwood (European oak) and diffuse-porous hardwood (Norway maple), were used in the study. The wood surfaces were finished by sanding with aluminum oxide sandpapers of different grits: P60, P120, P180, and P240. It was shown that among the analyzed factors (wood species, anatomical section, measurement direction, and sandpaper grit size) and the interactions between them, the direction of measurement had the greatest influence (47%) on the Ra parameter values for oak wood. The sandpaper grit determined 22% of the Ra parameter variability. The measurement direction and the grit size of the sandpaper were identified as the most influential factors affecting the Rsm parameter values. Comparable patterns were observed in the case of Norway maple wood. Due to its diffuse-porous structure, the roughness of maple wood was less affected by the sandpaper grit compared to that of oak wood. Wood species had the greatest influence, increased from 41% to 71% when examining the contact angle at phase boundary wood-water after 3 s and 30 s. Sandpaper grit showed the greatest impact on the contact angles at the wood–diiodomethane phase boundary. This impact was practically at the same level after testing the contact angles after 3 s (27%) and after 30 s (28%). Wood species determined the color parameters, being responsible for 93% of the L* parameter, 50% of parameter a*, and 78% of parameter b*. The influence of sandpaper grit on the a* and b* parameter values was at a low level, i.e., 4%. SEM micrographs revealed the diverse structural characteristics of the wood following the sanding process. Full article

The antimicrobial activity of silver nanoparticles (AgNPs) makes them a valuable tool in various industries. Recently, biosynthesis has become the preferred method for nanoparticle synthesis, and among organisms that can be used as AgNP producers, filamentous fungi have attracted the greatest interest. In particular, wood decay fungi are considered promising candidates for AgNP biosynthesis. Biogenic AgNPs have been proven to have strong antibacterial potential and antifungal activity. The aim of this study was to evaluate the antifungal potential of AgNPs synthesized using the brown-rot decay fungus Gloeophyllum striatum DSM 9592 against four pathogenic fungal strains: Candida albicans, Malassezia furfur, Aspergillus flavus and Aspergillus fumigatus. Moreover, changes in the tested strains’ lipidome and cell membrane properties induced by the presence of AgNPs were investigated. The results revealed that the obtained AgNPs exerted fungistatic activity against all the strains tested. M. furfur, with a MIC value of 0.39 μg/mL obtained for all AgNP types, was found to be the most susceptible to the action of AgNPs. The lipidomic analysis revealed that the presence of AgNPs caused an increase in cell membrane fluidity in both A. flavus and C. albicans, and the mechanisms of response to AgNPs differed between the tested strains. Full article