Search Results (130)

This study investigates the carbonation degree of reclaimed water (RW) and its potential use as mixing water for cementitious materials under controlled laboratory conditions using a simplified CO₂ injection method. To reproduce the chemical environment of actual RW, a synthetic reclaimed water (SRW) system with a cement-to-sand ratio of 8:2 was prepared and used throughout the evaluation. Thermogravimetric analysis revealed that the cementitious solids suspended in SRW exhibit high reactivity with CO₂, achieving a net CO₂ uptake of 16.8%, equivalent to 8.31 g of CO₂ sequestered per kilogram of RW. The use of untreated RW as mixing water slightly reduced flowability and increased superplasticizer demand compared with distilled water, whereas carbonation treatment of RW improved workability and mitigated the rapid initial setting typically observed with untreated RW. Notably, replacing 3% of the cement with carbonated RW solids did not cause any reduction in compressive strength, indicating that the carbonated solids can be incorporated without compromising mechanical performance. These results confirm that the CaCO₃ formed during RW carbonation remains stably retained within mortar and concrete, demonstrating the feasibility of using carbonated RW as a dual-function material—serving both as mixing water and as a medium for CO₂ sequestration. Full article

Industrial effluents often contain azeotropic mixtures that are difficult to separate by conventional distillation. An illustrative case is the methanol/methyl acetate/ethyl acetate (MA/ME/EA) mixture. To address these challenges, this work studies the conceptual design and optimization of the reactive distillation-based hybrid processes for separating the MA/ME/EA mixture with an EA-rich feed composition (0.25/0.20/0.55 mol fraction). An improved triple-column extractive–reactive distillation with a side-draw product (TCERD-SP) and its heat-integrated variant (TCERD-SP-HI) have been developed. In the TCERD-SP process, EA is strategically withdrawn as a side product, reconfiguring the extractive column into integrated pre-separation and entrainer-recovery sections, thereby reducing entrainer and energy demands. A four-step process design methodology is applied, including thermodynamics analysis, conceptual design, rigorous optimization via Aspen Plus integrated with the genetic algorithm to minimize total annual cost (TAC), and comparative evaluation of economic and environmental performance. The results show that the basic double-column pre-separation-reactive distillation (DCPSRD) process, optimal for a previous feed composition, exhibits unsatisfactory TAC performance for this EA-rich feed composition. Among the configurations studied, the TCERD-SP process exhibits superior performance, saving TAC by 8.4% and 14.4% compared to the TCERD and DCPSRD processes, respectively. In addition, based on the advantage of convenient heat integration between the side reboiler and the reactive distillation column condenser, the heat-integrated TCERD-SP-HI process achieves a further 10.7% TAC reduction. Thus, for this EA-rich feed examined in this work, the TCERD-SP and TCERD-SP-HI processes are demonstrated as effective solutions for recovering these valuable chemicals. Full article

The commitment to the Sustainable Development Goals and the need for increasing the circularity of industrial processes call for the exploitation of byproducts to generate value-added chemicals in cost- and energy-advantageous processes. In this process simulation-based research, two technologies were evaluated for the synthesis of isoamyl acetate from fusel oil: (A) an indirect process, and (B) a direct process using reactive distillation. Aspen Hysys v14.0 was used for simulation. A sensitivity analysis was performed to identify the influence of operating parameters on product purity, isoamyl acetate recovery and productivity, and energy consumption. Technology B was found to be the most favorable, obtaining 22.27 kg/h of isoamyl acetate with a purity of 98%. The total consumption values of cooling water and heating were 24.33 kW and 24.50 kW, respectively. Based on the best conditions, a technical–economic analysis was performed that demonstrated the viability of the process, obtaining a net present value (NPV) of US$3,587,110/year, an internal rate of return (IRR) of 38.95% and a payback period (PP) of 5.05 years. If acid recirculation is considered in the process, an NPV of US$7,232,950, an IRR of 56.34%, and a PP of 3.56 years are obtained. Full article

Ultrafine bubble (UFB) priming has recently emerged as a promising technique to enhance seed germination, yet its physiological mechanisms remain unclear. This study investigated the effects of UFB priming on adzuki bean (Vigna angularis) seeds under stress-free and drought conditions. Four treatments were tested: Control (non-primed), DW (primed with distilled water), UFB1 (4.56 × 10⁷ particles/mL), and UFB2 (1.13 × 10⁸ particles/mL). For priming, seeds were immersed in each solution at 25 ± 1 °C for 24 h. Seed traits, including water uptake, coat thickness, and total reactive oxygen species (ROS) levels in the priming solutions and seeds, were analyzed. UFB priming reduced seed coat thickness and slowed early water uptake without affecting final moisture content. Total ROS levels displayed a concentration-dependent pattern, with higher UFB increasing ROS in water but reducing them on the seed surface. Under stress-free conditions, all priming treatments accelerated germination, although higher UFB slightly prolonged T50. Under drought simulated by polyethylene glycol (PEG 10 and 15%), non-primed seeds were strongly inhibited, whereas primed seeds maintained high germination rates (>97%). Our results demonstrated that UFB priming improved water uptake, seed coat structure, and ROS signaling, enhancing seed performance of adzuki bean under favorable and drought conditions. Full article

Process intensification has gained significant importance during the last few years because of its potential to develop innovative structures with improved energy efficiency and better economics. One approach that has been developed in this field is the transformation of a process flowsheet with a series of conventional units into another one with minimal pieces of equipment. In this work we consider a base process to produce ethyl tert-butyl ether, which consists of a reactor and an isobaric distillation sequence. Given a set of design options provided by the gradual intensification of any processes that contain a dividing wall, reactive distillation, or reactive dividing wall columns, we take those intensified structures and make them subject to a multi-objective optimization task. The formulation consists of the minimization of the combination of economic, environmental, and inherent safety components. Different policies are simulated through weights assigned to each of those components. It is shown that the optimal structure depends on the priorities given to each term of the multi-objective formulation, and that the application of the optimization procedure further improves the economic and environmental potential provided by the base, fully intensified process, with reductions of up to 27.9 and 6.2 percent in those metrics. Full article

Mercury exposure has been linked to male infertility. Given that mercury chloride (HgCl₂) may promote an oxido-inflammatory milieu associated with pathophysiological derangements, it is hypothesised that Thymoquinone (TQ), an antioxidant and anti-inflammatory agent, may mitigate the gradual harmful effects of mercury exposure on rat testes, epididymis, and hypothalamus, as these organs are vital to reproductive function. To test this hypothesis, 40 rats (strain: Wistar; sex: male) were randomly assigned to five cohorts of eight rats each. After a 7-day acclimation, treatments were dispensed for 28 consecutive days accordingly: Cohort I: distilled water only, as control; Cohort II: HgCl₂ only (20 µg/mL); Cohort III: TQ only (2.5 mg/kg); Cohort IV: HgCl₂ + TQ (20 µg/mL + 2.5 mg/kg); and Cohort V: HgCl₂ + TQ (20 µg/mL + 5 mg/kg). Co-treatment with TQ preserved the body and organ weight of the HgCl₂ exposed animals. However, TQ did not reduce HgCl₂-induced dysfunction in sperm function and morphology. The serum follicle-stimulating hormone (FSH), luteinising hormone (LH), and testosterone were increased significantly (p < 0.05) by TQ co-treatment, while decreasing the prolactin level. TQ administration also increased (p < 0.05) testicular enzymes, including alkaline phosphatase (ALP), lactate dehydrogenase (LDH), acid phosphatase (ACP), and glucose-6-phosphate dehydrogenase (G6PD) activities, which HgCl₂ decreased. TQ administration increased (p < 0.05) HgCl₂-induced decreases in catalase (CAT), superoxide dismutase (SOD), glutathione peroxidase (GPx), glutathione (GSH), glutathione-s-transferase (GST), and total sulfhydryl group (TSH) levels in the testes, epididymis, and hypothalamus of experimental rats. Further, TQ reduced HgCl₂-mediated increases in RONS-reactive oxygen and nitrogen species; LPO–lipid peroxidation; PC–protein carbonyl formation; and XO–xanthine oxidase activity. Furthermore, levels of inflammatory biomarkers, including tumour necrosis factor alpha (TNF-α), nitric oxide (NO), interleukin-1 beta (IL-1β), and myeloperoxidase (MPO), were decreased (p < 0.05) in the co-treated groups, with a higher dose of TQ (5.0 mg/kg) showing a more pronounced protective effect. Additionally, TQ co-administration increased Bax and decreased Bcl-2 and p53 protein levels (p < 0.05), thereby protecting the rats’ testes, epididymis, and hypothalamus from HgCl₂-induced apoptosis. Molecular docking simulation analysis revealed TQ interaction dynamics with PPAR-α and PPAR-δ to suppress NF-kB-mediated pro-inflammatory sequela as well as activate Nrf-2-mediated antioxidant defence system. These predicted biological effects of TQ resonate with the findings from the in vivo studies. Therefore, supplementation with TQ may help reduce chemical-induced toxicities, including HgCl₂‘s reproductive toxicity. Full article

A transition metal-free synthesis of 1,2,5-trisubstituted 1H-indoles by a deprotonation–S_NAr cyclization sequence from 1-aryl-2-(2-fluoro-5-nitrophenyl)ethan-1-one (deoxy-benzoin) Schiff bases is reported. The starting deoxybenzoins were prepared by Friedel-Crafts acylation of activated aromatic compounds by 2-(2-fluoro-5-nitrophenyl)acetyl chloride with AlCl₃ or the corresponding acid with (CH₃SO₂)₂O. The Schiff bases were generated by slow distillation of toluene (18–24 h) from a heated solution of each deoxybenzoin (1 equiv) with a benzyl- or phenethylamine, a high-boiling aliphatic amine, or an aniline derivative (5 equiv). Subsequent addition of N,N-dimethylformamide, 2 equiv of anhydrous K₂CO₃, and heating at 90–95 °C for 18–24 h completed the synthesis. Benzyl-, phenethyl-, and high-boiling amines gave excellent yields while the heating requirements for the initial condensation made volatile aliphatic amines difficult to use and gave low yields. Aniline reactivities correlated with substituent-derived base strength, although modified conditions allowed some yields to be improved. Several anticipated competing processes had minimal impact on the outcome of the cyclizations. Full article

Tetrahydrofuran (THF) and methanol (MeOH) are widely used as organic solvents in chemical, pharmaceutical, and other industrial fields. The wastewater from producing 1,4-butanediol contains THF, MeOH, and water ternary azeotropic mixture. In this study, to protect the environment and improve economic feasibility, THF and MeOH from the wastewater must be recovered. Triple-column extractive distillation (TED), pressure-swing azeotropic distillation (PSAD) and reactive extractive dividing-wall column (REDWC) are introduced to separate this ternary system, and the NSGA-III algorithm is introduced to optimize the processes, taking the total annual cost (TAC), CO₂ emissions, and process route index (PRI) as objective functions. The results indicate that in comparison with TED process, TAC of PSAD and REDWC is reduced by 29.92% and 24.25%, respectively, and CO₂ emissions decreased by 18.01% and 25.13%, while PRI increased by 150.25% and 100.50%. This study can provide an insight for the design of ternary azeotropic system separation. Full article

Sensor-enabled digital twins (DTs) are reshaping precision dairy nutrition by seamlessly integrating real-time barn telemetry with advanced biophysical simulations in the cloud. Drawing insights from 122 peer-reviewed studies spanning 2010–2025, this systematic review reveals how DT architectures for dairy cattle are conceptualized, validated, and deployed. We introduce a novel five-dimensional classification framework—spanning application domain, modeling paradigms, computational topology, validation protocols, and implementation maturity—to provide a coherent comparative lens across diverse DT implementations. Hybrid edge–cloud architectures emerge as optimal solutions, with lightweight CNN-LSTM models embedded in collar or rumen-bolus microcontrollers achieving over 90% accuracy in recognizing feeding and rumination behaviors. Simultaneously, remote cloud systems harness mechanistic fermentation simulations and multi-objective genetic algorithms to optimize feed composition, minimize greenhouse gas emissions, and balance amino acid nutrition. Field-tested prototypes indicate significant agronomic benefits, including 15–20% enhancements in feed conversion efficiency and water use reductions of up to 40%. Nevertheless, critical challenges remain: effectively fusing heterogeneous sensor data amid high barn noise, ensuring millisecond-level synchronization across unreliable rural networks, and rigorously verifying AI-generated nutritional recommendations across varying genotypes, lactation phases, and climates. Overcoming these gaps necessitates integrating explainable AI with biologically grounded digestion models, federated learning protocols for data privacy, and standardized PRISMA-based validation approaches. The distilled implementation roadmap offers actionable guidelines for sensor selection, middleware integration, and model lifecycle management, enabling proactive rather than reactive dairy management—an essential leap toward climate-smart, welfare-oriented, and economically resilient dairy farming. Full article

This study aimed to investigate the efficacy of a composite coating composed of 150 mg/L ε-Poly-L-lysine (ε-PL) and 5 g/L chitosan (CTS) in extending the shelf life and maintaining the postharvest quality of fresh Tremella fuciformis. Freshly harvested T. fuciformis were treated by surface spraying, with distilled water serving as the control. The effects of the coating on storage quality, physicochemical properties, reactive oxygen species (ROS) metabolism, and membrane lipid metabolism were evaluated during storage at (25 ± 1) °C. The results showed that the ε-PL/CTS composite coating significantly retarded quality deterioration, as evidenced by reduced weight loss, maintained whiteness and color, and higher retention of soluble sugars, soluble solids, and soluble proteins. The coating also effectively limited water migration and loss. Mechanistically, the coated T. fuciformis exhibited enhanced antioxidant capacity, characterized by increased superoxide anion (O₂⁻) resistance capacity, higher activities of antioxidant enzymes (SOD, CAT, APX), and elevated levels of non-enzymatic antioxidants (AsA, GSH). This led to a significant reduction in malondialdehyde (MDA) accumulation, alongside improved DPPH radical scavenging activity and reducing power. Furthermore, the ε-PL/CTS coating preserved cell membrane integrity by inhibiting the activities of lipid-degrading enzymes (lipase, LOX, PLD), maintaining higher levels of key phospholipids (phosphatidylinositol and phosphatidylcholine), delaying phosphatidic acid accumulation, and consequently reducing cell membrane permeability. In conclusion, the ε-PL/CTS composite coating effectively extends the shelf life and maintains the quality of postharvest T. fuciformis by modulating ROS metabolism and preserving membrane lipid homeostasis. This study provides a theoretical basis and a practical approach for the quality control of fresh T. fuciformis. Full article

The combined effect of non-thermal plasma (NTP) and hydropriming on the germination performance and seedling characteristics of specific varieties of cucumber (Cucumis sativus L.) and broccoli (Brassica oleracea var. italica Plenck.) seeds after short-term storage is reported. Seeds were treated with NTP for 10 and 15 min, followed by hydropriming in distilled water for 24 h, and then stored for six months in the dark before evaluation. The treated cucumber seeds demonstrated a statistically significant enhancement in seed germination and seedling vitality indices. In contrast, broccoli seeds showed no significant improvement. The stimulatory effects observed in cucumber may be attributed to reactive oxygen and nitrogen species, which act as signaling molecules to promote stress tolerance and early growth. This study also highlights the potential of combined NTP treatment and hydropriming as a pre-sowing treatment for select crops, underscoring the need for species-specific optimization. The used, portable, and relatively inexpensive NTP device offers practical advantages for agricultural applications. Full article

In the present study, a process for the production of 2,2,3,3,4,4,4-heptafluorobutyl acetate (HFBAc) is proposed for the first time. The production process of HFBAc from acetic acid (AAc) and 2,2,3,3,4,4,4-heptafluorobutan-1-ol (HFBol) was carried out at laboratory scale using batch reactive distillation (BRD). The process was conducted at atmospheric pressure in the presence of an acid catalyst, with an excess of AAc relative to HFBol (initial molar ratio of reagents HFBol/AAc is 45/55). During the BRD, the aqueous phase of the distillate was withdrawn from the system, while the organic phase of the distillate was returned as reflux. Since part of AAc is lost along with the aqueous phase of the distillate, a minor excess of AAc is reasonable for maximizing the conversion of the most expensive reagent—HFBol. The losses of AAc and HFBol with the aqueous phase of the distillate were less than 2 mole % and less than 0.5 mole % of the feed, respectively. The purity of HFBAc after BRD was 97.9 wt. %, and the conversion of HFBol exceeded 99 mole % of the feed. The purity of certain product fractions of HFBAc was greater than 99.6 wt. %. The obtained data can be used for industrial technology development to obtain HFBAc. Full article

This review examines the chemical functionalization of Camelina, hemp, and rapeseed oils for the development of sustainable bio-based resins. Key strategies, including epoxidation, acrylation, and click chemistry, are discussed in the context of tailoring molecular structure to enhance reactivity, compatibility, and material performance. Particular emphasis is placed on overcoming the inherent limitations of vegetable oil structures to enable their integration into high-performance polymer systems. The agricultural sustainability and environmental advantages of these feedstocks are also highlighted alongside the technical challenges associated with their chemical modification. Functionalized oils derived from Camelina, hemp, and rapeseed have been successfully applied in various resin systems, including protective coatings, pressure-sensitive adhesives, UV-curable oligomers, and polyurethane foams. These advances demonstrate their growing potential as renewable alternatives to petroleum-based polymers and underline the critical role of structure–property relationships in designing next-generation sustainable materials. Ultimately, the objective of this review is to distill the most effective functionalization pathways and design principles, thereby illustrating how Camelina, hemp, and rapeseed oils could serve as viable substitutes for petrochemical resins in future industrial applications. Full article

Reactive oxygen–nitrogen species (RONS) production in a Peltier-cooled hybrid dielectric barrier discharge (HDBD) reactor operated with humid air is characterized. Fourier-transform infrared spectroscopy (FTIR) is used to determine the RONS in the HDBD-produced gases. The presence of molecules ${\mathrm{O}}_3$, ${\mathrm{NO}}_2$, ${\mathrm{N}}_2$O, ${\mathrm{N}}_2{\mathrm{O}}_5$, and ${\mathrm{HNO}}_3$ is evaluated. The influence of HDBD reactor operation parameters on the FTIR result is discussed. The strongest influence of Peltier cooling on RONS chemistry is reached at conditions related to a high specific energy input (SEI): high voltage and duty cycle of plasma width modulation (PWM), and low gas flow. Both PWM and Peltier cooling can achieve a change in the chemistry from oxygen-based to nitrogen-based. ${\mathrm{N}}_2{\mathrm{O}}_5$ and ${\mathrm{HNO}}_3$ are detected at a low humidity of 7% in the reactor input air but not at humidity exceeding 90%. In addition to the FTIR analysis, the plasma-activated water (PAW) is investigated. PAW is produced by bubbling the HDBD plasma gas through 12.5 mL of distilled water in a closed-loop circulation at a high SEI. Despite the absence of ${\mathrm{N}}_2{\mathrm{O}}_5$ and ${\mathrm{HNO}}_3$ in the gas phase, the acidity of the PAW is increased. The pH value decreases on average by 0.12 per minute. Full article

The insufficient optimization of calcination process parameters severely restricts the enhancement of rice husk ash (RHA) volcanic ash activity. In this study, an intelligent muffle furnace was used for multi-parameter coupled regulation, combined with microscopic characterization techniques, to elucidate the effects of temperature, cooling mode, heating rate, and holding time on the reactivity of RHA. The results showed that the effect of calcination temperature on the volcanic ash activity of RHA was dominant. RHA calcined at 600–700 °C showed a honeycomb porous structure, displayed broad amorphous SiO₂ diffraction peaks and up to 95% content of SiO₂, and exhibited the best volcanic ash activity. The increased crystallinity of RHA calcined at 800 °C led to a decrease in its activity. The subcooling treatment with distilled water effectively rebuilt the lamellar structure, reduced the crystallinity, and enhanced the reactivity. The samples incorporated with 600 °C calcined RHA showed higher compressive strength at 3 days compared to 800 °C calcined RHA. Full article