Search Results (729)

This study investigated a novel method of recovering energy from iron ore sinter using solid iron oxide heat transfer materials. Traditionally, air is passed through the sinter either in an open conveyor or a sealed vessel to recover energy. The bed materials used were a magnetite concentrate, hematite ore, goethite–hematite ore and sinter fines. A shortwave thermal camera and quartz reactor were used measure infrared radiation from the process. The thermal imaging was combined with image analysis techniques to visualise the transfer of thermal energy through the system. The results showed that energy moved rapidly through the system with peak heating rates of 18 °C/min at a lump sinter temperature of 600 °C. The ratio of heating rate to cooling rate was as high as 8.6:1.0, indicating efficient retention of energy by the bed materials. The bed composition, determined by X-ray fluorescence and X-ray diffraction was used to calculate the heat capacity based on pure material properties. The resultant energy balance determined thermal efficiency to be between 32 and 46% for the sinter fines and hematite–goethite ore, resulting in predicted fuel savings of up to 9.4kg/tonne with similar heat utilisations to the air recovery process. Thermal imaging combined with Brunauer–Emmett–Teller surface area measurements and scanning electron microscopy analysis experimentally replicated mathematical heat transfer model predictions that a smaller total pore volume resulted in less thermally resistive bed. Image analysis illustrated the breaking of the heat front between the less resistive solid and more resistive air in porous beds versus even conduction of heat through a dense bed. The oxide distribution in the bed materials impacted heat transfer, as at a lump temperature of 500 °C was controlled by hydrated oxide content whereas at 600 °C Fe₂O₃ was the more dominant driver. Full article

Myoglobin (Mb), a heme-containing protein, plays crucial roles in storing and transporting oxygen in muscle cells. Various Mb structures have been extensively determined using conventional cryogenic crystallography, providing valuable information for understanding the molecular mechanisms of the protein. However, this approach has limitations attributable to cryogenic temperatures and radiation damage. Serial femtosecond crystallography (SFX) using X-ray free-electron lasers is an emerging technique that enables the determination of biologically relevant room-temperature structures without causing radiation damage. In this study, we assessed the crystallization, collection, and processing of SFX diffraction data of Mb from equine skeletal muscle. Needle- and needle cluster-shaped Mb crystals were obtained using the microbatch method. Fixed-target SFX data collection was performed at the Pohang Accelerator Laboratory X-ray Free Electron Laser, yielding 1389 indexed diffraction patterns. The phase problem was solved by molecular replacement. The preliminary Mb structure determined at 2.3-Å resolution in this study exhibited subtle structural differences in the heme environment compared with previously reported Mb structures determined by SFX. These results both confirm the feasibility of myoglobin SFX experiments and establish a foundation for future time-resolved studies aiming to visualize ligand binding and oxygen transport. Full article

Diffractive sail components may be used in part or whole for in-space propulsion and attitude control. A sun-facing hybrid diffractive solar sail having reflective front facets and transmissive side facets is described. This hybrid design seeks to minimize the undesirable scattering from side facets. Predictions of radiation pressure are compared for analytical geometrical optics and numerical finite difference time domain approaches. Our calculations across a spectral irradiance band from 0.5 to 3 μm suggest the transverse force in a sun facing configuration reaches 48% when the refractive index of the sail material is 1.5. Diffraction measurements at a representative optical wavelength of 633 nm support our predictions. Full article

Background/Objectives: We report the development of a novel intraocular sustained-release implantable pharmaceutical formulation, designed to be placed in the anterior chamber of the eye after cataract surgery. The device is intended to reduce postoperative inflammation, and to prevent opportunistic bacterial infections that may lead to endophthalmitis. Methods: The implants were produced via hot-melt extrusion, using a twin-screw extruder to process a homogeneous mixture of polylactide-co-glycolic acid, moxifloxacin hydrochloride (MOX HCl) and dexamethasone (DEX). Quality control tests included drug content determination, release rate profile evaluation, and several instrumental characterization techniques (scanning electron microscopy (SEM), confocal Raman microscopy, differential scanning calorimetry, and X-ray diffraction). Long-term and accelerated stability tests were also performed, following ICH guidelines. Sterilization was achieved by exposing samples to gamma radiation. In vivo exploratory studies were carried out in healthy rabbits to evaluate the safety and overall performance of the implantable formulation. Results: In terms of quality control, drug content was found to be homogeneously distributed throughout the implants, and it also met the label claim. In vitro release rate was constant for MOX HCl, but non-linear for DEX, increasing over time. In vivo preliminary tests showed that the inserts completely biodegraded within approximately 20 days. No clinical signs of anterior segment toxic syndrome or statistically significant intraocular pressure differences were found between treatment and control groups. Conclusions: The implants developed in this study can act as sustained-release depots for the delivery of both DEX and MOX HCl, and are biocompatible with ocular structures. Full article

Hybrid organic–inorganic materials incorporating high-Z nanocompounds represent an emerging area of research with high, cost-effective potential for radiation detection applications, owing to their ability to enable unprecedented architectures and functional devices. Herein, we introduce a new hybrid system composed of tungstate nanoparticles (SrWO₄ or CdWO₄) blended with P3HT:PCBM, engineered for direct X-ray detection without the need for external bias. The nanocrystalline tungstates were synthesized through a hydrothermal route. X-ray diffraction and scanning electron microscopy were employed to characterize the nanoparticle structure and morphology, respectively. Incorporation of high-Z tungstate nanoparticles was found to substantially enhance detector sensitivity within specific energy ranges, with performance tunable by varying the tungstate composition. The use of the fabricated detectors was demonstrated for both spectroscopic and imaging applications. Full article

Waveguide-integrated metasurfaces offer a promising platform for ultracompact on-chip optical systems, enabling applications such as fluorescence sensing, holography, and near-eye displays. In particular, integrated achromatic metalenses that couple guided modes to free-space radiation are highly desirable for single-molecule fluorescence sensing, where high numerical aperture (NA), efficient light focusing, and consistent focal volume overlap across excitation and emission wavelengths are critical. However, designing integrated high-NA metalenses with multi-wavelength operation remains fundamentally challenging due to the wavelength-dependent propagation of guided modes. Here, we present an inverse design framework that simultaneously optimizes the geometries and positions of silicon nitride nanofins atop a slab waveguide to achieve diffraction-limited focusing at three wavelengths with unity NA. The resulting metalens outperforms conventional segmented designs in focusing efficiency and sidelobe suppression, particularly at wavelengths corresponding to the excitation and emission bands of the model fluorophore Alexa Fluor 647. Numerical analysis shows that the design yields a high molecule detection efficiency suitable for epi-fluorescence single-molecule sensing. This work highlights the potential of inverse-designed metalenses as a versatile on-chip platform for advanced applications in fluorescence spectroscopy, augmented reality, or optical trapping. Full article

This study presents a new approach for generating the symmetrical plan curve of a double-curved antenna reflector’s radiation pattern as an alternative to optimizing it when the primary radiation source has a given pattern. The results obtained are compared with those achieved using a source with a different characteristic, clearly indicating the potential to minimize the reflector surface area through illumination with a specific characteristic. Moreover, diffraction calculations for an antenna including a reflector that employs the calculated vertical profile derived from a primary radiation source characterized by a given beam pattern are presented. This analysis considers two cases: one with horizontal polarization and the other with vertical polarization. Simulation results are provided for the diffraction calculation of a reflector with radiation characteristics that employs a sectorial horn antenna with directivity characteristics. In this setup, the angular limits of the reflected beam are sequentially adjusted, allowing the changes in the directivity characteristic to be observed and discussed to determine the optimal configuration for the intended application. Full article

Traditionally, an open window is considered a kind of reference for perfect sound absorption. The sound reflection and absorption of an aperture is analyzed by means of an impedance model representing a rectangular absorbing surface surrounded by a thin, infinite rigid baffle. The most important part of the model is the complex radiation impedance. It is shown that the sound absorption coefficient of the open window is not exactly 1, but it is angle-dependent and decreases towards low frequencies. Two diffraction effects are identified: the refraction that appears when a wave passes through an aperture, and the scattering of waves from the edges of the aperture. A revised model for sound absorption is presented, taking these diffraction effects into account. It is shown that the refraction effect is the reason for measured absorption coefficients greater than 1, whereas the scattering effect can explain the typical decrease in absorption towards lower frequencies. The revised model is validated against examples of measured sound absorption. Finally, it is discussed how room acoustic calculation models can handle realistic absorption data. Full article

Spinels like Co₃O₄ have acquired relevance because of their photocatalytic, electrocatalytic, optical and magnetic properties. In this context, we investigated the defect structure evolution of compounds synthetized using the nitrate precursor method and after annealing cycles at temperatures ranging from 260 to 650 °C by means of thermogravimetric analysis (TGA), neutron powder diffraction (NPD), X-ray powder diffraction (XRPD) coupled to Pair Distribution Function (PDF) analysis, and Density Functional Theory (DFT) calculations. Deuterated and hydrogenated precursors were adopted to produce the samples for NPD and XRPD experiments, respectively. TGA measurements displayed weight losses, the extent of which increased on lowering the preparation annealing temperature, suggesting that the adopted wet synthesis introduces structural water in the sample. Both XRPD and NPD revealed the presence of vacancies in tetrahedral cobalt sites ($V_{Co1}^{″}$) whose concentration at RT decreases on raising the annealing temperatures, while octahedral cobalt and oxygen sites were fully occupied in all the samples. In addition, the $V_{Co1}^{″}$ presence induces a shrinking of the volume of the CoO₄ tetrahedra. The combination of DFT calculation and diffraction revealed that deuterium/hydrogen ions ($D_i^{•}$/$H_i^{•}$), introduced during the synthesis by the nitrate precursor balanced the $V_{Co1}^{″}$. Finally, DFT calculations revealed that ($D_i^{•}$/$H_i^{•}$) in Co₃O₄ forms hydroxyl groups. Full article

The Planck constant is a fundamental parameter of nature that appears in the description of phenomena on a microscopic scale. Its origin is associated with an explanation of the distribution of the blackbody spectrum performed by Max Planck. This constant stands the basis for the definition of the International System of Units (SI), and, in particular, the new mass definition. This paper presents different methods for determining the Planck constant based on phenomena such as blackbody radiation, light diffraction through a single slit, the current–voltage characteristics of a light-emitting diode, the photoelectric phenomenon, and the hydrogen atom spectrum in the visible range. The Planck constant was measured using instruments in a stationary laboratory and via remote access. The influence of various factors on the accuracy of the measurements was determined, and the consistency of the obtained results with the accepted value of the Planck constant are examined and discussed. Full article

This paper investigates the performance of a spacecraft equipped with a diffractive sail in a heliocentric mission scenario that requires phasing along a prescribed elliptical orbit. The diffractive sail represents an evolution of the more traditional reflective solar sail, which converts solar radiation pressure into thrust using a large reflective surface typically coated with a thin metallic film. In contrast, the diffractive sail proposed by Swartzlander leverages the properties of an advanced metamaterial-based film to generate a net transverse thrust even when the sail is Sun-facing, i.e., in a configuration that can be passively maintained by a suitably designed spacecraft. Specifically, this study considers a sail membrane covered with a set of electro-optically controlled diffractive panels. These panels employ a (controlled) binary metamaterial arrayed grating to steer the direction of photons exiting the diffractive film. This control technique has recently been applied to achieve a circle-to-circle interplanetary transfer using a Sun-facing diffractive sail. In this work, an optimal control law is employed to execute a rapid phasing maneuver along an elliptical heliocentric orbit with specified characteristics, such as those of Earth and Mercury. The analysis also includes a limiting case involving a circular heliocentric orbit. For this latter scenario, a simplified and elegant control law is proposed based on a linearized form of the equations of motion to describe the heliocentric dynamics of the diffractive sail-based spacecraft during the phasing maneuver. Full article

One of the advantages of the EPR spectroscopy method in assessing structural defects caused by irradiation is the fact that using this method it is possible to determine not only the concentration dependences of the defect structure but to also establish their type, which is not possible with methods such as X-ray diffraction or scanning electron microscopy. Based on the data obtained, the role of variation in the ratio of components in Li₄SiO₄–Li₂TiO₃ ceramics on the processes of softening under high-dose irradiation with protons simulating the accumulation of hydrogen in the damaged layer, as well as the concentration of structural defects in the form of oxygen vacancies and radiolysis products on the processes of high-temperature degradation of ceramics, was determined. It was found that the main changes in the defect structure during the prolonged thermal exposure of irradiated samples are associated with the accumulation of oxygen vacancies, the density of which was estimated by the change in the intensity of singlet lithium, characterizing the presence of E-centers. At the same time, it was found that the formation of interphase boundaries in the structure of Li₄SiO₄–Li₂TiO₃ ceramics leads to the inhibition of high-temperature degradation processes in the case of post-radiation thermal exposure for a long time. Also, during the conducted studies, the role of thermal effects on the structural damage accumulation rate in Li₄SiO₄–Li₂TiO₃ ceramics was determined in the case when irradiation is carried out at different temperatures. During the experiments, it was determined that the main contribution of thermal action in the process of proton irradiation at a fluence of 5 × 10¹⁷ proton/cm² is an increase in the concentration of radiolysis products, described by changes in the intensities of spectral maxima, characterized by the presence of defects such as ≡Si–O, SiO₄³⁻ and Ti³⁺ defects. Full article

The frequency-domain free-surface Green’s function method is widely used in solving ship hydrodynamic problems, with its core challenge lying in the computation of the Green’s function and its partial derivatives. This study analyzes the relationship between the free-surface Green’s function and its derivatives, proposing a machine learning-based recursive prediction method termed the pulsating source recursive prediction method. The accuracy and efficiency of this method under various parameter settings are investigated, and its application to the hydrodynamic calculations of container ship S175 and a bulk carrier is demonstrated. Results show that the predicted Green’s function achieves an accuracy of 3–6 decimals, with computational efficiency surpassing numerical methods and matching analytical approaches. The hydrodynamic results are reliable, confirming the method’s practical value. Full article

Understanding the limitations of cold-formed aluminum alloys in practice applications is essential, particularly due to the risk of substructural changes and a reduction in strength when exposed to elevated temperatures. In this study, the thermal stability of the ultra-fine-grained (UFG) structure formed by equal channel angular pressing (ECAP) at room temperature and the mechanical properties of the AlSi7MgCu0.5 alloy were investigated. Prior to ECAP, the plasticity of the as-cast alloy was enhanced by a heat treatment consisting of solution annealing, quenching, and artificial aging to achieve an overaged state. Four repetitive passes via ECAP route A resulted in the homogenization of eutectic Si particles within the α-solid solution, the formation of ultra-fine grains and/or subgrains with high dislocation density, and a significant improvement in alloy strength due to strain hardening. The main objective of this work was to assess the microstructural and mechanical stability of the alloy after post-ECAP annealing in the temperature range of 373–573 K. The UFG microstructure was found to be thermally stable up to 523 K, above which notable grain and/or subgrain coarsening occurred as a result of discontinuous recrystallization of the solid solution. Mechanical properties remained stable up to 423 K; above this temperature, a considerable decrease in strength and a simultaneous increase in ductility were observed. Synchrotron radiation X-ray diffraction (XRD) was employed to analyze the phase composition and crystallographic characteristics, while transmission electron microscopy (TEM) was used to investigate substructural evolution. Mechanical properties were evaluated through tensile testing, impact toughness testing, and hardness measurements. Full article

Efficient detection of toxic and flammable vapors remains a major technological challenge, especially for environmental and industrial applications. This paper reports on the fabrication technology and gas-sensing properties of nanostructured Ga₂O₃/GaS_0.98Se_0.02. The β-Ga₂O₃ nanowires/nanoribbons with inclusions of Ga₂S₃ and Ga₂Se₃ microcrystallites were obtained by thermal treatment of GaS_0.98Se_0.02 slabs in air enriched with water vapors. The microstructure, crystalline quality, and elemental composition of the obtained samples were investigated using electron microscopy, X-ray diffraction, and Raman spectroscopy. The obtained structures show promising results as active elements in gas sensor applications. Vapors of methanol (CH₃OH), ethanol (C₂H₅OH), and acetone (CH₃-CO-CH₃) were successfully detected using the nanostructured samples. The electrical signal for gas detection was enhanced under UV light irradiation. The saturation time of the sensor depends on the intensity of the UV radiation beam. Full article