Search Results (215)

This paper proposes an Adam-optimized Deep Belief Networks (Adam-DBNs) denoising method for throat-attached piezoelectric signals. The method aims to process mechanical vibration signals captured through polyvinylidene fluoride (PVDF) sensors attached to the throat region, which are typically contaminated by environmental noise and physiological noise. First, the short-time Fourier transform (STFT) is utilized to convert the original signals into the time–frequency domain. Subsequently, the masked time–frequency representation is reconstructed into the time domain through a diagonal average-based inverse STFT. To address complex nonlinear noise structures, a Deep Belief Network is further adopted to extract features and reconstruct clean signals, where the Adam optimization algorithm ensures the efficient convergence and stability of the training process. Compared with traditional Convolutional Neural Networks (CNNs), Adam-DBNs significantly improve waveform similarity by 6.77% and reduce the local noise energy residue by 0.099696. These results demonstrate that the Adam-DBNs method exhibits substantial advantages in signal reconstruction fidelity and residual noise suppression, providing an efficient and robust solution for throat-attached piezoelectric sensor signal enhancement tasks. Full article

Vibration energy offers promising potential for renewable energy harvesting, especially in conditions where conventional sources such as solar power may be limited or intermittent. This study proposes a rain energy harvester (REH) that converts the kinetic energy of raindrops into electrical energy using nonlinear thin plates, integrated with piezoelectric elements. Two plate configurations—fully hinged (H-H-H-H) and clamped–hinged–free–hinged (C-H-F-H)—are investigated. Theoretical modeling and simulation results are compared with experimental data, with special attention paid to the role of slapping forces in improving prediction accuracy. A power management system is also introduced to stabilize and regulate the harvested voltage. Results confirm the feasibility of rain-induced energy harvesting, showing potential for application in rain-prone areas and integration with existing infrastructure such as solar panels, tents, or canopies. Full article

This paper presents a low-power data acquisition (DAQ) chip tailored for impulsive charge sensing, featuring a comparator-gated dynamic acquisition (CG-DAQ) architecture. A dynamic comparator triggers both the gain stage and a 12-bit successive-approximation register (SAR) analog-to-digital converter (ADC) through a shared timing path, enabling event-driven amplification and digitization. Programmable conversion gain ranging from 5 to 40 mV/pC is achieved by switching the sampling capacitance. Fabricated in TSMC 65 nm CMOS, the chip detects input charges from 0.01 to 36 pC, supports a signal bandwidth of 10 kHz to 100 kHz, and enables sampling rates up to 1 MS/s. It achieves an input-referred noise of 5.5 fC_rms and a peak signal-to-noise ratio (SNR) of 67 dB, all within a 54 μW power envelope and a compact 0.03 mm² core area. The proposed architecture facilitates accurate and energy-efficient charge-domain sensing for capacitive and piezoelectric sensor applications. Full article

This paper presents a comprehensive summary of recent advances in circuit topologies for piezoelectric energy harvesting, leading to self-powered systems (SPSs), covering the full-bridge rectifier (FBR) and half-bridge rectifier (HBR), AC-DC converters, and maximum power point tracking (MPPT) techniques. These approaches are analyzed with respect to their advantages, limitations, and overall impact on energy harvesting efficiency. Th work explores alternative methods that leverage phase shifting between voltage and current waveform components to enhance conversion performance. Additionally, it provides detailed insights into advanced design strategies, including adaptive power management algorithms, low-power control techniques, and complex impedance matching. The paper also addresses the fundamental principles and challenges of converting mechanical vibrations into electrical energy. Experimental results and performance metrics are reviewed, particularly in relation to hybrid approaches, load impedance, vibration frequency, and power conditioning requirements in energy harvesting systems. This review aims to provide researchers and engineers with a critical understanding of the current state of the art, key challenges, and emerging opportunities in piezoelectric energy harvesting. By examining recent developments, it offers valuable insights into optimizing interface circuit design for the development of efficient and self-sustaining piezoelectric energy harvesting systems. Full article

This study presents a closed-form solution for the dynamic response of a sandwich beam subjected to arbitrary impact loading, with a particular focus on energy harvesting from an attached piezoelectric layer. A thin piezoelectric patch is bonded to the bottom surface of the beam to convert mechanical vibrations into electrical energy. The governing equations of motion are derived using Hamilton’s principle, considering a non-symmetric sandwich cross-section and incorporating higher-order shear deformation effects. The state–space method is employed to obtain the exact dynamic response of the beam under impact excitation. The differential equations governing the output voltage and harvested power are solved analytically based on the derived response. The natural frequencies and dynamic responses are validated against classical beam theory, highlighting the significance of shear deformation. Numerical examples are provided to evaluate the generated voltage and energy harvesting efficiency. The results demonstrate the strong potential for energy harvesting from sandwich beam vibrations and elucidate the influence of impact loading conditions, distributed load amplitude, and the geometric dimensions of the beam on the harvested output. Full article

With the rapid rise in Internet of Things (IoT) and artificial intelligence (AI) technologies, there is an increasing need for portable, wearable, and self-powered flexible sensing devices. In such scenarios, self-powered nanogenerators have emerged as promising energy harvesters capable of converting ambient mechanical stimuli into electrical energy, enabling the development of autonomous flexible sensors and sustainable systems. This review highlights recent advances in nanogenerator technologies—particularly those based on piezoelectric and triboelectric effects—with a focus on soft, flexible, and gel-based polymer materials. Key mechanisms of energy conversion are discussed alongside strategies to enhance performance through material innovation, structural design, and device integration. Special attention is given to the role of gel-type composites, which offer unique advantages such as mechanical tunability, self-healing ability, and biocompatibility, making them highly suitable for next-generation wearable, biomedical, and environmental sensing applications. We also explore the evolving landscape of energy applications, from microscale sensors to large-area systems, and identify critical challenges and opportunities for future research. By synthesizing progress across materials, mechanisms, and application domains, this review aims to guide the rational design of high-performance, sustainable nanogenerators for the next era of energy technologies. Full article

The currently used electrical energy devices for portable applications are in limited life and need of frequent recharging, it is a big bottleneck for wireless and transportation systems. The scientific community is motivated to find innovative and efficient devices to convert environmental energy into useful forms. Nanogenerator can mitigate this issue by harvesting ambient energy of different forms into useful electrical energy. Particularly flexible nanogenerators can efficiently convert ambient mechanical energy into electrical energy which can be fruitfully used for self-powered sensors and electronic appliances. Zinc oxide is an interesting photosensitive and piezoelectric material that is expected to play a vital role in the synergetic harvesting of environmental thermal, sound, mechanical, and solar energies. As ZnO can be synthesized using easy methods and materials at low cost, the conversion efficiencies of solar and other energy forms can increase considerably. ZnO is a versatile material with interesting semiconducting, optical, and piezoelectric properties; it can be used advantageously to harvest more than one type of ambient energy. The coupled semiconducting and piezoelectric properties of ZnO are attractive for fabricating nanogenerators capable of harvesting both ambient optical and mechanical energies simultaneously. These nanolevel conversion devices are much required to power remote and implantable devices without the need for additional power sources. The present review briefly discusses the principles and mechanisms of different energy harvesting abilities of ZnO nanorods and their composites by consolidating available literature. In addition, the developments taking place in nanogenerators of different kinds—such as photovoltaic, piezoelectric, pyroelectric, and triboelectrics for self-powered technology—and their progress in hybrid energy harvesting application is reviewed. Full article

For complex mechanical transmission equipment, shaft bearings are usually enclosed together with the shaft in the internal space of the housing to maintain good sealing and reliability. However, it is difficult to monitor the status of the shaft bearing through external sensors on the housing, while internal sensors face challenges in energy supply and data transmission. Therefore, a piezoelectric transducer ring-based energy harvesting microelectromechanical system (PTR-EH-MEMS) is proposed for the condition monitoring of shaft bearings. Specifically, the piezoelectric transducer ring is designed to convert mechanical vibrations into electrical energy, which simultaneously acts as a self-powered monitoring sensor through energy harvesting. In addition, the MEMS is embedded for piezoelectric data processing and condition monitoring of the shaft bearings. To verify the proposed PTR-EH-MEMS, an experimental investigation is implemented under different conditions. The experimental results demonstrate that the system can achieve the maximum DC output of 0.8 V and the root mean square power of 43.979 μW within 128 s, which can effectively identify early-stage bearing faults frequency through a self-powered mode. By combining energy harvesting with condition monitoring capability, the PTR-EH-MEMS offers a compact and sustainable approach for predictive maintenance in rotating machinery, reducing the reliance on external power sources and enhancing the reliability of industrial systems. Full article

This paper focuses on the mathematical and numerical modeling of a non-classical macro fiber composite (MFC) piezoelectric transducer, MFC-P2, integrated with an aluminum cantilever beam for energy harvesting applications. It seeks to harness the transverse vibration energy in the environment to power small electronic devices, such as wireless sensors, where conventional power sources are inconvenient. The P2-type macro fiber composites (MFC-P2) are specifically designed for transverse energy harvesting applications. They offer high electric source capacitance and improved electric charge generation due to the strain developed perpendicularly to the voltage produced. The system is modeled analytically using Euler–Bernoulli beam theory and piezoelectric constitutive equations, capturing the electromechanical coupling in the d31 mode. Numerical simulations are conducted using COMSOL Multiphysics 6.29 to reduce the complexity of the mathematical model and analyze the effects of material properties, geometric configurations, and excitation conditions. The theoretical model is based on the transverse vibrations of a cantilevered beam using Euler–Bernoulli theory. The natural frequencies and mode shapes for the first four are determined. Depending on these, the resonance frequency, voltage, and power outputs are evaluated across a 12 kΩ resistive load. The results demonstrate that the energy harvester effectively operates near its fundamental resonant frequency of 10.78 Hz, achieving the highest output voltage of approximately 0.1952 V and a maximum power output of 0.0031 mW. The generated power is sufficient to drive ultra-low-power devices, validating the viability of MFC-based cantilever structures for autonomous energy harvesting systems. The application of piezoelectric phenomena and obtaining electrical energy from mechanical vibrations can be powerful solutions in such systems. The application of piezoelectric phenomena to convert mechanical vibrations into electrical energy presents a promising solution for self-powered mechatronic systems, enabling energy autonomy in embedded sensors, as well as being used for structural health monitoring applications. Full article

Industrial motors generate vibration energy that can be converted into electrical energy using piezoelectric vibration energy harvesters (pVEHs). These energy harvesters can power devices or function as self-powered sensors. However, optimal electromechanical designs of pVEHs are required to improve their output performance under different vibration frequency and amplitude conditions. To address this challenge, we performed the electromechanical modeling of a multilayer pVEH that harvests vibration energy from induction electric motors at frequencies close to 30 Hz. In addition, a parametric analysis of the geometry of the multilayer piezoelectric device was conducted to optimize its deflection and output voltage, considering the substrate length, piezoelectric patch position, and dimensions of the central hole. Our analytical model predicted the deflection and first bending resonant frequency of the piezoelectric device, with good agreement with predictions from finite element method (FEM) models. The proposed piezoelectric device achieved an output voltage of 143.2 V and an output power of 3.2 mW with an optimal resistance of 6309.5 kΩ. Also, the principal stresses of the pVEH were assessed using linear trend analysis, finding a safe operating range up to an acceleration of 0.7 g. The electromechanical design of the pVEH allowed for effective synchronization with the vibration frequency of an induction electric motor. This energy harvester has a potential application in industrial electric motors to transform their vibration energy into electrical energy to power sensors. Full article

The growing demand for sustainable and self-powered technologies in automotive applications has led to increased interest in energy harvesting from vehicle suspensions. Recovering mechanical energy from road-induced vibrations offers a viable solution for powering wireless sensors and autonomous electronic systems, reducing dependence on external power sources. This study presents the design, modeling, and experimental validation of a hybrid energy-harvesting system that integrates piezoelectric and magnetoelectric effects to efficiently convert mechanical vibrations into electrical energy. A model-based systems engineering (MBSE) approach was used to optimize the system architecture, ensuring high energy conversion efficiency, durability, and seamless integration into suspension systems. The theoretical modeling of both piezoelectric and magnetoelectric energy harvesting mechanisms was developed, providing analytical expressions for the harvested power as a function of system parameters. The designed system was then fabricated and tested under controlled mechanical excitations to validate the theoretical models. Experimental results demonstrate that the hybrid system achieves a maximum power output of 16 µW/cm² from the piezoelectric effect and 3.5 µW/cm² from the magnetoelectric effect. The strong correlation between theoretical predictions and experimental measurements confirms the feasibility of this hybrid approach for self-powered automotive applications. Full article

The growing global demand for sustainable energy solutions has led to increased interest in kinetic energy harvesting as a viable alternative to traditional power sources. High-foot-traffic environments, such as public spaces and religious sites, generate significant mechanical energy that often remains untapped. This study explores energy-harvesting technologies applicable to public areas with heavy foot traffic, focusing on Al-Haram Mosque in Saudi Arabia—one of the most densely populated religious sites in the world. The research investigates the potential of piezoelectric, triboelectric, and hybrid systems to convert pedestrian foot traffic into electrical energy, addressing challenges such as efficiency, durability, scalability, and integration with existing infrastructure. Piezoelectric materials, including PVDF and BaTiO₃, effectively convert mechanical stress from footsteps into electricity, while triboelectric nanogenerators (TENGs) utilize contact electrification for lightweight, flexible energy capture. In addition, this study examines material innovations such as 3D-printed biomimetic structures, MXene-based composites (MXene is a two-dimensional material made from transition metal carbides, nitrides, and carbonitrides), and hybrid nanogenerators to improve the longevity and scalability of energy-harvesting systems in high-density footfall environments. Proposed applications for Al-Haram Mosque include energy-harvesting mats embedded with piezoelectric and triboelectric elements to power IoT devices, LED lighting, and environmental sensors. While challenges remain in material degradation, scalability, and cost, emerging hybrid systems and advanced composites present a promising pathway toward sustainable, self-powered infrastructure in large-scale, high-foot-traffic settings. These findings offer a transformative approach to energy sustainability, reducing reliance on traditional energy sources and contributing to Saudi Arabia’s Vision 2030 for renewable energy adoption. Full article

Energy harvesting in the automotive sector is a rapidly growing field aimed at improving vehicle efficiency and sustainability by recovering wasted energy. Various technologies have been developed to convert mechanical, thermal, and environmental energy into electrical power, reducing dependency on traditional energy sources. This manuscript provides a comprehensive review of energy harvesting applications/methodologies, aiming to trace the research lines and future developments. This work identifies the main categories of harvesting solutions, namely mechanical, thermal, and hybrid/environmental solar–wind systems; each section includes a detailed review of the technical and scientific state of the art and a comparative analysis with detailed tables, allowing the state of the art to be mapped for identification of the strengths of each solution, as well as the challenges and future developments needed to enhance the technological level. These improvements focus on energy conversion efficiency, material innovation, vehicle integration, energy savings, and environmental sustainability. The mechanical harvesting section focuses on energy recovery from vehicle vibrations, with emphasis on regenerative suspensions and piezoelectric-based solutions. Specifically, solutions applied to suspensions with electric generators can achieve power outputs of around 1 kW, while piezoelectric-based suspension systems can generate up to tens of watts. The thermal harvesting section, instead, explores methods for converting waste heat from an internal combustion engine (ICE) into electrical power, including thermoelectric generators (TEGs) and organic Rankine cycle systems (ORC). Notably, ICEs with TEGs can recover above 1 kW of power, while ICE-based ORC systems can generate tens of watts. On the other hand, TEGs integrated into braking systems can harvest a few watts of power. Then, hybrid solutions are discussed, focusing on integrated mechanical and thermal energy recovery systems, as well as solar and wind energy harvesting. Hybrid solutions can achieve power outputs above 1 kW, with the main contribution from TEGs (≈1 kW), compared to piezoelectric systems (hundreds of W). Lastly, a section on commercial solutions highlights how current scientific research meets the automotive sector’s needs, providing significant insights for future development. For these reasons, the research results aim to be guidelines for a better understanding of where future studies should focus to improve the technological level and efficiency of energy harvesting solutions in the automotive sector. Full article

Flexible wearable electronic devices have found widespread applications in health monitoring and human–machine interaction. Piezoelectric sensors, capable of converting mechanical stress into electrical signals, serve as critical components in these systems. In this study, we enhanced the piezoelectric performance of PVDF-based composite materials through MoS₂ incorporation. Experimental results demonstrated that MoS₂ addition effectively increased the β-phase content in PVDF, achieving a maximum value of 70.0% at an optimal MoS₂ concentration of 0.75 wt%. Density functional theory (DFT) calculations revealed that while β-phase PVDF possesses slightly higher energy than other phases, it exhibits stronger adsorption interactions and enhanced charge transfer with MoS₂, thereby promoting β-phase formation. The fabricated MoS₂/PVDF composite nanofiber film maintained stable voltage output under repeated mechanical stress through 2000 operational cycles. When implemented as a body-mounted sensor, the composite material demonstrated exceptional responsiveness to human motions, confirming its practical potential for wearable electronics applications. Full article

This review investigates the role of vortex-induced vibrations (VIVs) in hydrokinetic energy harnessing, shedding light on their dual nature as both a challenge in offshore engineering and an untapped resource for renewable energy. VIVs serve as a novel energy source, converting the kinetic energy of fluid flows into mechanical or electrical power. The review discusses the various energy conversion mechanisms, highlighting the unique benefits and challenges of electromagnetic, piezoelectric, and triboelectric systems. A significant emphasis is placed on optimizing VIV energy harnessing to balance maximizing energy output while maintaining structural stability. The review provides insights into the geometric configurations, material properties, and advanced computational methods that are pivotal in this optimisation process. In conclusion, this review provides a comprehensive analysis of the current progress and persistent challenges in VIV research, offering actionable insights and innovative solutions that will advance the field of efficient and sustainable energy. Full article