Search Results (12)

This paper reports on the testing and evaluation of a passive autoranging (AR) method designed to dynamically extend the measurement range of a photonic current transducer (PCT) to pave the way toward a realization of a combined metering- and protection-class current sensor. The PCT utilizes a current transformer (CT), a piezoelectric transducer (PZT), and a fiber Bragg grating (FBG) to enable current measurement at multiple points in an electrical power network whereby multiple sensors are deployed and interrogated serially using a single optical fiber. The autoranging technique relies on incorporating static MOSFET switches to instantaneously short individual serially connected CT burdens in response to a measured current magnitude exceeding pre-set thresholds. The AR circuit switching events produce distinctive signal features that are used by the proposed switching algorithm to apply appropriate scaling factors to reconstruct the measured current from the optical signal. It is shown through laboratory experiments that the AR circuit correctly reacts to pre-set burden current thresholds of 130% of the nominal value and 22 times the nominal value, signifying its “metering” and “protection” range boundaries. The circuit reaction time is below 4 ms, rendering it suitable for standard power system protection purposes. Moreover, the operation of the AR circuit is demonstrated for burden currents of up to 100 A for over 1 s, satisfying a test procedure for the secondary CT circuit, as required by some power system operators. It is demonstrated that the proposed switching algorithm allows for a correct reconstruction of the burden currents from the optical signal acquired by the FBG interrogator, offering the potential to realize a dual-class optical current sensor. Full article

As human–computer interaction has become increasingly popular, haptic technology has become a research topic of great interest, since vibration perception, as a type of haptic feedback, can enhance user experience during an interaction. However, the high power consumption of existing drivers makes them unsuitable for use in portable devices. In this paper, a bidirectional four-switch buck–boost converter (FSBBC) and Proportional–Integral (PI)–Proportional (P) feedback control are proposed to implement a driver in a high-capacitance piezoelectric actuator which is capable of recovering the energy stored in the high-capacitance load and increasing efficiency. The FSBBC offers an extended input voltage range, rendering significant technological advantages in diverse applications such as automobiles, laptops, and smartphones. By implementing specific control strategies, the FSBBC not only outperforms conventional buck–boost converters in boosting performance, but also ensures that the output and input voltages retain the same polarity. This effectively addresses the polarity inversion challenge inherent to traditional buck–boost circuits. Within the FSBBC, the significant reduction in voltage stress endured by the MOSFET effectively minimizes system costs and size and enhances reliability. The proposed system was simulated in Simulink, which was combined with testing on a field-programmable gate array (FPGA). The driver is capable of driving capacitors of up to 2.9 $\mathsf{\mu }$F, with 80 Vpp output and 2.75% total harmonic distortion (THD) observed in the test. Full article

This paper presents a piezoelectric (PE) energy harvesting circuit based on the DSSH (double synchronized switch harvesting) principle. The circuit consisted of a rectifier and a DC–DC circuit, which achieves double synchronized switch operation for the PE transducer in each vibration half-cycle. One of the main challenges of the DSSH scheme was precisely controlling the switch timing in the second loop of the resonant loops. The proposed circuit included a MOS transistor in the second loop to address this challenge. It utilized its threshold voltage to manage the stored energy in the intermediate capacitor per vibration half-cycle to simplify the controller for the DSSH circuit. The circuit can operate under either the DSSH scheme or the ESSH (enhanced synchronized switch harvesting) scheme, depending on the value of the intermediate capacitor. In the DSSH scheme, the following DC–DC circuit reused the rectifier’s two diodes for a short period. The prototype circuit was implemented using 16 discrete components. The proposed circuit can be self-powered and started up without a battery. The experimental results showed that the proposed circuit increased the power harvested from the PE transducer compared to the full-bridge (FB) rectifier. With two different intermediate capacitors of 100 nF and 320 nF, the proposed circuit achieved power increases of 3.2 and 2.7 times, respectively. The charging efficiency of the proposed circuit was improved by a factor of 5.1 compared to the typical DSSH circuit. Full article

In this paper, we present a novel technique for passively autoranging a photonic current transducer (PCT) that incorporates a current transformer (CT), piezoelectric transducer (PZT) and fiber Bragg grating (FBG). Due to the usage of single-mode fiber and FBG, multiple PCTs can be interconnected and distributed over a long distance, for example along a power network, greatly reducing the cost of sensor deployment and offering other unique advantages. The autoranging technique relies on the usage of multiple, serially connected CT burden resistors and associated static MOSFET switches to realize instantaneous shortening of the resistors in response to increasing measured current. This functionality is realized passively, utilizing a modular, μW-power comparator circuit that powers itself from the electrical energy supplied by the CT within a small fraction of the 50/60 Hz cycle. The resultant instantaneous changes in sensor gain will be ultimately detected by the central FBG interrogator through real-time analysis of the optical signals and will be used to apply appropriate gain scaling for each sensor. The technique will facilitate the usage of a single PCT to cover an extended dynamic range of the measurement that is required to realize a combined metering- and protection-class current sensor. This paper is limited to the description of the design process, construction, and testing of a prototype passive autoranging circuitry for integration with the PCT. The two-stage circuitry that is based on two burden resistors, 1 Ω and 10 Ω, is used to prove the concept and demonstrate the practically achievable circuit characteristics. It is shown that the circuit correctly reacts to input current threshold breaches of approximately 2 A and 20 A within a 3 ms reaction time. The circuit produces distinct voltage dips across burden resistors that will be used for signal scaling by the FBG interrogator. Full article

Remotely driven smart actuator technology by microwave is attractive since it simplifies and reduces the complexity and weight of the remote system. A rectifying antenna (rectenna) array receives and converts microwave power into DC power for actuators, and the power collected from the rectenna array should be accurately allocated and distributed to each actuator. In this research, a new power distribution (PD) logic circuit is studied to control an actuator array effectively. The PD logic circuit was designed and tested to validate it. The preliminary design was tested for a 4 × 4 piezoelectric actuator array with a 16 dual-gate MOSFET array and a computer-controlled 16-channel DAC board. Additionally, power compensation as a remedial approach for a partial power failure of the array was integrated. This PD scheme with a new logic device simplifies the thousands of control cables required for connecting each array element. The performance and limitations of the designed PD circuit are discussed. Full article

Harvesting energy from human motion for powering small scale electronic devices is attracting research interest in recent years. A piezoelectric device (PD) is capable of harvesting energy from mechanical motions, in the form of alternating current (AC) voltage. The AC voltage generated is of low frequency and is often unstable due to the nature of human motion, which renders it unsuitable for charging storage device. Thus, an electronic circuit such as a full bridge rectifier (FBR) is required for direct current (DC) conversion. However, due to forward voltage loss across the diodes, the rectified voltage and output power are low and unstable. In addition, the suitability of existing rectifier circuits in converting AC voltage generated by PD as a result of low frequency human motion induced non-sinusoidal vibration is unknown. In this paper, an improved H-Bridge rectifier circuit is proposed to increase and to stabilise the output voltage. To study the effectiveness of the proposed circuit for human motion application, a series of experimental tests were conducted. Firstly, the performance of the H-Bridge rectifier circuit was studied using a PD attached to a cantilever beam subject to low frequency excitations using a mechanical shaker. Real-life testing was then conducted with the source of excitation changed to a human performing continuous cycling and walking motions at a different speed. Results show that the H-Bridge circuit prominently increases the rectified voltage and output power, while stabilises the voltage when compared to the conventional FBR circuit. This study shows that the proposed circuit is potentially suitable for PEH from human motion. Full article

This paper presents an ultrasound transceiver application-specific integrated circuit (ASIC) directly integrated with an array of 12 × 80 piezoelectric transducer elements to enable next-generation ultrasound probes for 3D carotid artery imaging. The ASIC, implemented in a 0.18 µm high-voltage Bipolar-CMOS-DMOS (HV BCD) process, adopted a programmable switch matrix that allowed selected transducer elements in each row to be connected to a transmit and receive channel of an imaging system. This made the probe operate like an electronically translatable linear array, allowing large-aperture matrix arrays to be interfaced with a manageable number of system channels. This paper presents a second-generation ASIC that employed an improved switch design to minimize clock feedthrough and charge-injection effects of high-voltage metal–oxide–semiconductor field-effect transistors (HV MOSFETs), which in the first-generation ASIC caused parasitic transmissions and associated imaging artifacts. The proposed switch controller, implemented with cascaded non-overlapping clock generators, generated control signals with improved timing to mitigate the effects of these non-idealities. Both simulation results and electrical measurements showed a 20 dB reduction of the switching artifacts. In addition, an acoustic pulse-echo measurement successfully demonstrated a 20 dB reduction of imaging artifacts. Full article

In order to improve the output sensitivity of the piezoelectric acceleration sensor, this paper proposed a high sensitivity acceleration sensor based on a piezoelectric metal oxide semiconductor field effect transistor (MOSFET). It is constituted by a piezoelectric beam and an N-channel depletion MOSFET. A silicon cantilever beam with Pt/ZnO/Pt/Ti multilayer structure is used as a piezoelectric beam. Based on the piezoelectric effect, the piezoelectric beam generates charges when it is subjected to acceleration. Due to the large input impedance of the MOSFET, the charge generated by the piezoelectric beam can be used as a gate control signal to achieve the purpose of converting the output charge of the piezoelectric beam into current. The test results show that when the external excitation acceleration increases from 0.2 g to 1.5 g with an increment of 0.1 g, the peak-to-peak value of the output voltage of the proposed sensors increases from 0.327 V to 2.774 V at a frequency of 1075 Hz. The voltage sensitivity of the piezoelectric beam is 0.85 V/g and that of the proposed acceleration sensor was 2.05 V/g, which is 2.41 times higher than the piezoelectric beam. The proposed sensor can effectively improve the voltage output sensitivity and can be used in the field of structural health monitoring. Full article

An energy-harvesting interface for kinetic energy harvesting from high-voltage piezoelectric and triboelectric generators is proposed in this paper. Unlike the conventional kinetic energy-harvesting interfaces optimized for continuous sinusoidal input, the proposed harvesting interface can efficiently handle irregular and random high voltage energy inputs. An N-type mosfet (NMOS)-only power stage design is introduced to simplify power switch drivers and minimize conduction loss. Controller active mode power is also reduced by introducing a new voltage peak detector. For efficient operation with potentially long intervals between random kinetic energy inputs, standby power consumption is minimized by monitoring the input with a 43 pW wake-up controller and power-gating all other circuits during the standby intervals. The proposed harvesting interface can harvest energy from a wide range of energy inputs, 10 s of nJ to 10 s of µJ energy/pulse, with an input voltage range of 5–200 V and an output range of 2.4–4 V under discontinuous as well as continuous excitation. The proposed interface is examined in two scenarios, with integrated power stage devices (maximum input 45 V) and with discrete power stage devices (maximum input 200 V), and the harvesting efficiency is improved by up to 600% and 1350%, respectively, compared to the case when harvesting is performed with a full bridge rectifier. Full article

Piezoelectric vibration based energy harvesting systems have been widely utilized and researched as powering modules for various types of sensor systems due to their ease of integration and relatively high energy density compared to RF, thermal, and electrostatic based energy harvesting systems. In this paper, a low-power CMOS full-bridge rectifier is presented as a potential solution for an efficient energy harvesting system for piezoelectric transducers. The energy harvesting circuit consists of two n-channel MOSFETs (NMOS) and two p-channel MOSFETs (PMOS) devices implementing a full-bridge rectifier coupled with a switch control circuit based on a PMOS device driven by a comparator. With a load of 45 kΩ, the output rectifier voltage and the input piezoelectric transducer voltage are 694 mV and 703 mV, respectably, while the V_OUT versus V_IN conversion ratio is 98.7% with a PCE of 52.2%. The energy harvesting circuit has been designed using 130 nm standard CMOS process. Full article

A logging-while-drilling (LWD) caliper is a tool used for the real-time measurement of a borehole diameter in oil drilling engineering. This study introduces the mechanical structure and working principle of a new LWD caliper based on ultrasonic distance measurement (UDM). The detection range is a major performance index of a UDM system. This index is determined by the blind zone length and remote reflecting interface detection capability of the system. To reduce the blind zone length and detect near the reflecting interface, a full bridge acoustic emission technique based on bootstrap gate driver (BGD) and metal-oxide-semiconductor field effect transistor (MOSFET) is designed by analyzing the working principle and impedance characteristics of a given piezoelectric transducer. To detect the remote reflecting interface and reduce the dynamic range of the received echo signals, the relationships between the echo amplitude and propagation distance of ultrasonic waves are determined. A signal compensation technique based on time-varying amplification theory, which can automatically change the gain according to the echo arrival time is designed. Lastly, the aforementioned techniques and corresponding circuits are experimentally verified. Results show that the blind zone length in the UDM system of the LWD caliper is significantly reduced and the capability to detect the remote reflecting interface is considerably improved. Full article

This paper presents a new method for a vibration-based piezoelectric energy harvesting system using a backtracking search algorithm (BSA)-based proportional-integral (PI) voltage controller. This technique eliminates the exhaustive conventional trial-and-error procedure for obtaining optimized parameter values of proportional gain (Kp), and integral gain (Ki) for PI voltage controllers. The generated estimate values of Kp and Ki are executed in the PI voltage controller that is developed through the BSA optimization technique. In this study, mean absolute error (MAE) is used as an objective function to minimize output error for a piezoelectric energy harvesting system (PEHS). The model for the PEHS is designed and analyzed using the BSA optimization technique. The BSA-based PI voltage controller of the PEHS produces a significant improvement in minimizing the output error of the converter and a robust, regulated pulse-width modulation (PWM) signal to convert a MOSFET switch, with the best response in terms of rise time and settling time under various load conditions. Full article