Search Results (870)

Nanofiltration (NF) is considered a competitive purification method for acidic stream treatments. However, conventional thin-film composite NF membranes degrade under acid exposures, limiting their applications in industrial acid treatment. For example, wet-process phosphoric acid contains impurities of multivalent metal ions, but NF membrane technologies for impurity removal under harsh conditions are still immature. In this work, we develop a novel strategy of acid-resistant nanofiltration membranes based on interfacial polymerization (IP) of polyethyleneimine (PEI) and cyanuric chloride (CC) with the s-triazine ring. The IP process was optimized by orthogonal experiments to obtain positively charged PEI-CC membranes with a molecular weight cut-off (MWCO) of 337 Da. We further applied it to the approximate industrial phosphoric acid purification condition. In the tests using a mixed solution containing 20 wt% P₂O₅, 2 g/L Fe³⁺, 2 g/L Al³⁺, and 2 g/L Mg²⁺ at 0.7 MPa and 25 °C, the NF membrane achieved 56% rejection of Fe, Al, and Mg and over 97% permeation of phosphorus. In addition, the PEI-CC membrane exhibited excellent acid resistance in the 48 h dynamic acid permeation experiment. The simple fabrication procedure of PEI-CC membrane has excellent acid resistance and great potential for industrial applications. Full article

This study evaluated the effect of various adhesive systems, particularly silane application, on the repair bond strength of a nanofill resin composite and associated stress distribution using finite element analysis (FEA). A total of 105 composite specimens (4 × 6 mm) were aged by thermal cycling (10,000 cycles), roughened, etched with phosphoric acid, and assigned to seven groups (n = 15): G1. control—no adhesive; G2. Single Bond Universal Adhesive; G3. composite primer; G4. PQ1; G5. Silane + PQ1; G6. Clearfil Universal Bond; G7. All-Bond Universal. Shear bond strength was measured using a universal testing machine (1 mm/min), and failure modes were microscopically classified. FEA was conducted under static and fatigue conditions using 3D models built in Fusion-360. Mechanical properties were obtained from technical data and the literature. A 300 N load was applied and contact detection (0.05 mm) and constraint zones were defined. Statistical analysis was performed using one-way ANOVA and Tukey’s HSD (p = 0.05). Pearson’s correlation was used to assess the relationship between bond strength and von Mises stress. The highest bond strength was found in G2 (21.54 MPa) while G1 showed the lowest (8.86 MPa). Silane-treated groups exhibited favorable stress distribution and a strong correlation between experimental and simulated outcomes. Silane applications significantly enhance composite repair performance. Full article

Phosphorous slag is an industrial by-product generated in the process of producing yellow phosphorus by electric furnace, which occupies a substantial number of land resources and causes serious environmental pollution. The comprehensive utilization of phosphorous slag is a major topic relevant to the sustainability of the yellow phosphorus industry. In this paper, we attempted to utilize phosphorous slag as a supplementary cementing material to prepare silica-aluminum based cementitious material (SAC-PHS). To determine how phosphorus influences the early-age hydration reaction process of silica-aluminum based cementitious material, three groups of samples, PHS₂₀, PHS₂₅, and PHS₃₀, with better mechanical properties were selected to deeply investigate their one-week hydration characteristics. Characterization results showed that the main hydration products of SAC-PHS were C-A-S-H gels and ettringite. PHS₂₅ specimen produced more C-A-S-H gels and ettringite than the other two samples after one-week hydration. Interestingly, the P/Si atomic ratio indicated that chemical bonds were formed between Si and P during the formation of C-A-S-H gels, which improved the strength of SAC-PHS. Our findings offer valuable insights for the application of phosphorous slag in construction and building materials and promote the efficient resource utilization of phosphorous residue. Full article

The deep defluorination of water remains a significant environmental challenge. In this work, aluminum was loaded onto the bifunctional resin S957 containing a phosphoric-sulfonic acid difunctional group for efficient fluoride removal. Al-S957 demonstrated excellent fluoride removal performance across a broad pH range. When anions and organics coexisted, Al-S957 exhibited significantly better fluoride adsorption performance compared to aluminum-loaded monofunctional resins. The adsorption followed an endothermic chemisorption process on a monolayer surface. FTIR and XPS analyses further revealed that fluoride removal relied on a ligand exchange mechanism. Column adsorption conducted over five cycles highlighted the strong practical potential of Al-S957. The results suggested that Al-S957 exhibits significant potential for practical applications. Full article

The spectroscopic properties of Pr³⁺ ions in the aluminosilicate matrix were investigated for the first time. Synthesis of CaAl₂SiO₆ (CASO) polycrystals doped with Pr³⁺ ions was carried out using the sol–gel method. The crystalline structures have been confirmed with XRD measurement. The absorption, excitation, emission spectra, and time decay profiles of the praseodymium (III) ions were measured and analyzed. It was found that upon excitation with visible light, this material exhibits emission mainly in the UVC region, via an upconversion emission process. The Stokes emission in the visible range is observed mainly from the ³P₀ and ¹D₂ energy levels. The ¹D₂→³H₄ emission is very stable even at very high temperatures. The studied aluminosilicate phosphors possess characteristics that confirm their potential in upconversion emission applications. Full article

Rare earth elements (REEs) have garnered significant global attention due to their essential role in advanced technologies. Sri Lanka is endowed with various REE-bearing minerals, including the apatite-rich deposit in the Eppawala area, commonly known as Eppawala rock phosphate (ERP). However, direct extraction of REEs from ERP is technically challenging and economically unfeasible. This study introduces a novel, integrated approach for recovering REEs from ERP as a by-product of nitrophosphate fertilizer production. The process involves nitric acid-based acidolysis of apatite, optimized at 10 M nitric acid for 2 h at 70 °C with a pulp density of 2.4 mL/g. During cooling crystallization, 42 wt% of calcium was removed as Ca(NO₃)₂.4H₂O while REEs remained in the solution. REEs were then selectively precipitated as REE phosphates via pH-controlled addition of ammonium hydroxide, minimizing the co-precipitation with calcium. Further separation was achieved through selective dissolution in a sulfuric–phosphoric acid mixture, followed by precipitation as sodium rare earth double sulfates. The process achieved over 90% total REE recovery with extraction efficiencies in the order of Pr > Nd > Ce > Gd > Sm > Y > Dy. Samples were characterized for their phase composition, elemental content, and morphology. The fertilizer results confirmed the successful production of a nutrient-rich nitrophosphate (NP) with 18.2% nitrogen and 13.9% phosphorus (as P₂O₅) with a low moisture content (0.6%) and minimal free acid (0.1%), indicating strong agronomic value and storage stability. This study represents one of the pioneering efforts to valorize Sri Lanka’s apatite through a novel, dual-purpose, and circular approach, recovering REEs while simultaneously producing high-quality fertilizer. Full article

Objectives: In the animal model, we aim to evaluate the bone behavior in two innovative and different laser-treated (L1–L2) titanium implants compared to sandblasted and acid-etched (SBAE) used as control. Materials and Methods: A total of twenty-seven dental implants (8.5 × 3.3 mm) used for the study (Sweden & Martina, Due Carraie Padova-Italy) were placed in three Pelibuey female sheep. Implant surface profilometric, contact angle and EDX analysis were detected. After 15, 30 and 90 days, histological, histomorphometric, SEM-EDX analysis and Bone-to-implant Contact (BIC), Dynamic Osseointegration Index (DOI) and Bone Quality Index (BQI) (as Calcium and Phosphorous atomic percentages ratio) were performed. Results: All surfaces showed relevant profilometric and wettability differences. After 15 days, BIC₁₅ showed great differences in L2 (42.1 ± 2.6) compared to L1 (5.2 ± 3.1) and SBAE (23.3 ± 3.9) as well as after 30 days (L2 (82.4 ± 2.2), L1 (56.2 ± 1.3) and SBAE (77.3 ± 0.4)). After 90 days, relevant lower BIC₉₀ values were detected in L1 (68.4 ± 0.2) compared to L2 (86.4 ± 0.1) and SBAE (86.2 ± 0.6). The DOI showed higher rates of bone growth in L2 after 15 (DOI₁₅ = 2.81) and 30 days (DOI₃₀ = 2.83), compared to L1 (DOI₁₅ = 0.38, DOI₃₀ = 3.40) and SBAE (DOI₁₅ = 1.55, DOI₃₀ = 2.58). The DOI₉₀ drastic slowdown in SBAE (0.96), L1 (0.76), and L2 (0.95) confirmed the Early Osseointegration (EO) as a crucial phase. Moreover, before loading, the lower global BQI in L1 (Ca 44.43 ± 0.08–P 46.14 ± 5.15) and SBAE (Ca 45.31 ± 2.08–P 48.28 ± 1.12) compared to L2 (Ca 79.81 ± 2.08–P 81.85 ± 3.14) allows to assert that osseointegration process and bone healing could not be considered complete if compared to the native bone. Conclusions: The BIC, DOI, and BQI results showed that osseointegration is a dynamic process, confirming the crucial role of surface characteristics able to influence it, especially the early osseointegration (EO) phase. The short-time L2 implants’ higher bone quantity and quality results, compared to L1 and SBAE, suggested the fundamental role of this innovative laser-obtained surface in “secondary stability” and predictable long-term clinical outcomes. Full article

The objective of this study was to evaluate the effect of morpholine on saliva-contaminated resin-based composite (RBC)-CAD/CAM material repaired with resin composite. Fifty RBC-CAD/CAM materials were fabricated and assigned to five groups and surface-treated with saliva, phosphoric acid (PHR), morpholine (MRL), and a universal adhesive agent (Scotchbond universal plus, SCP) based on the following techniques: group 1, saliva; group 2, SCP; group 3, saliva + SCP; group 4, saliva + PHR + SCP; and group 5, saliva + MRL + SCP. An ultradent model was placed on the specimen center, and then the resin composite was pressed and light-cured for 20 s. A mechanical testing device was used to evaluate the samples’ shear bond strength (SBS) scores. The debonded specimen areas were inspected under a stereomicroscope to identify the failure mechanisms. The data were analyzed using one-way ANOVA, and the significance level (p < 0.05) was set with Tukey’s test. The highest SBS values were in groups 2, 4 and 5, with values of 21.43 ± 1.93, 20.93 ± 1.46, and 22.02 ± 1.77 MPa, respectively. However, they were not statistically different (p > 0.05). Group 1 had the lowest SBS value by a significant amount (1.88 ± 1.01 MPa). All specimens in group 1 showed adhesive failures. Moreover, groups 2–5 found cohesive and mixed failures. In conclusion, morpholine and phosphoric acid effectively enhance bond strength. These results indicate that alternative surface modifications with morpholine for saliva-contaminated RBC-CAD/CAM materials can significantly improve the outcome. Full article

The escalating threats of climate change, pollution, and a rapidly growing global population are putting immense pressure on water resources, highlighting the urgent need for innovative wastewater recycling solutions. This study explores the potential of biochar, derived from common kitchen waste as a sustainable and efficient adsorbent for copper removal from contaminated water. Seven factors were studied for their influence on the adsorption process, including heavy metal concentration (50–250 ppm), biochar dosage (0.5–2.5 g), contact time (30 min to 29 h), temperature (20–80 °C), pH (2.67–8.07), and the efficacy of activated versus non-activated biochar, with activation carried out using phosphoric acid, silver nitrate, and sulfuric acid. Biochar characterization using Raman spectroscopy, specific surface area by Brunauer–Emmett–Teller analysis (BET), Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), Scanning Electron Microscopy—Energy Dispersive X-ray Spectroscopy (SEM-EDX), and zeta potential analysis revealed its robust adsorption capacity. Notably, silver nitrate-loaded biochar exhibited the highest adsorption capacity (24.44 mg/g) at 250 ppm of copper and the highest removal rate at about 99.3%, whereas phosphoric acid activation reduced this capacity to 5 mg/g due to structural damage. Importantly, biochar’s adsorption capacity was found to be pH-independent, simplifying operational requirements for treatment systems. Optimal conditions for maximum copper removal were determined to be 100 ppm of copper, a temperature of 60 °C, and a contact time of 30 min. The Langmuir isotherm model best described the adsorption process, indicating a monolayer adsorption with a maximum capacity of 23.25 mg/g. This comprehensive analysis underscores biochar’s potential as a cost-effective, efficient, and environmentally friendly solution for copper removal from wastewater. Full article

The overuse of synthetic nitrogen fertilizer in vineyards degrades soil quality and poses environmental risks. Partial substitution of synthetic nitrogen with organic alternatives may enhance grapevine performance and soil sustainability, depending on the substitution rate. This study evaluated the effects of replacing synthetic nitrogen with composted spent mushroom substrate at five different rates (0%, 25%, 50%, 75%, and 100%, denoted as NOS, OS-25, OS-50, OS-75, and OS-100, respectively) and a control with no nitrogen fertilization applied (CK), on soil fertility, root growth, and photosynthetic performance in grapevine seedlings. Compared to CK, nitrogen fertilization and organic substitution significantly increased soil electrical conductivity, organic matter, and macronutrient contents, but had no significant effect on soil pH. Organic substitution markedly improved leaf photosynthetic capacity in the summer, with the highest rates observed under OS-25, exceeding CK and NOS by 32.98–63.19% and 13.93–27.38%, respectively. Root growth was also significantly enhanced by organic substitution, with OS-25 exhibiting the best performance. Fine roots in the 0.0–0.5 mm diameter class were dominant, accounting for 56.88–63.06% of total root length and 96.22–97.31% of total root tip count. Increasing substitution rates beyond 25% yielded no further improvements in photosynthesis or root growth. Mantel test analysis indicated strong positive correlations between soil fertility parameters (e.g., alkali-hydrolyzable nitrogen, available phosphorous and potassium) and both photosynthetic efficiency and root growth. These findings suggest that an appropriate substitution rate (i.e., 25%) of organic nitrogen using spent mushroom substrate effectively improves soil fertility, simultaneously optimizing photosynthetic capacity and root growth of grapevine seedlings. Full article

The expansion of the livestock industry has led to an increase in biogas slurry discharge, which contains high levels of nitrogen (N) and phosphorous (P). Struvite precipitation is an effective method for the recovery of N and P from biogas slurry, and the recovered N and P can be applied as a slow-release fertilizer in agricultural production. To form an industrial chain for struvite recovery and application in agriculture, we investigated the factors affecting struvite recovery from biogas slurry generated on a pig farm and evaluated its efficacy as a fertilizer. The N and P recovery efficiency was higher when magnesium chloride (MgCl₂) was used as a magnesium (Mg) source compared with magnesium oxide (MgO), and the optimal reaction conditions were pH 10, a reaction time of 20 min, a stirring rate of 200 rpm, and a Mg/P/N ratio of 1.2:1.0:1.0, which achieved N and P recovery rates of 81.83% and 99.67%, respectively. To further investigate the commercial utility of using struvite recovered from biogas slurry as a fertilizer, the growth and content of nutrients in two common vegetables in China were measured. The vegetable quality-related parameters of bock choy (Brassica chinensis) improved as the proportion of struvite in the fertilizer increased. Fresh weight, soluble sugar, and soluble protein increased by 194.47%, 46.13%, and 82.42%, respectively. The quality-related parameters of water celery (Oenanthe javanica (Blume) DC.) increased with an increasing proportion of struvite (27.90 mg·g⁻¹ soluble sugar and 42.20 mg·g⁻¹ soluble protein). The application of struvite precipitated from biogas slurry in plant cultivation shows great potential and lays a solid foundation for the resourceful recovery and utilization of biogas slurry. Full article

Compressed earth blocks (CEBs) obtained by laterite material geopolymerization have great potential as building materials; however, plastic waste recycling remains an important challenge for the 21st century. Samples of lateritic materials (LAT) from the locality of Kompina and its surroundings (Littoral-Cameroon) were collected, given the region’s association with polyethylene terephthalate powder (P). They were used to make geopolymeric laterite bricks using a phosphoric acid solution (A) concentrated at 10 mol/L, at a fixed value of 20% phosphoric acid, and values of 0, 5, 10, 15, and 20% polyethylene terephthalate (PET) powder. To assess the suitability of these formulations for construction, the CEBs were tested and their physico-mechanical and thermal characteristics determined, including water absorption rate, compressive strength (CS), thermal conductivity, and effusivity. It was revealed that water absorption decreased for the LAT1 and LAT6 formulas, at 6.73% and 5.01%, respectively, with the lowest value being recorded when 10% of the PET powder was used. The water absorption increased beyond this percentage; the CS values did too, with a peak at 10% PET powder, reaching 6.92 MPa and 6.96 MPa for LAT1 and LAT6, respectively, and values decreasing beyond this point. The thermal conductivity and effusivity decreased, with the lowest values at 20% of the PET powder being 0.289 W·m⁻¹·K⁻¹ and 1078.46 J·K⁻¹·m⁻²·s^−1/2, and 0.289 W·m⁻¹·K⁻¹ and 1078.2 J·K⁻¹·m⁻²·s^−1/2 for LAT1 and LAT6, respectively. Based on the results obtained, we conclude that the formulation LAT-P10A20 is the most recommendable. Full article

Hollow fibre renewal liquid membranes (HFRLMs) are susceptible to third-phase formation during rare earth element (REE) extraction using D2EHPA (bis(2-ethylhexyl phosphoric acid)), potentially leading to membrane fouling and decreased mass transfer efficiency. This study investigated the effects of various parameters, such as the composition of the aqueous feed and organic phases, on the third-phase formation and limiting organic concentration (LOC) of REE(III) in D2EHPA. Higher concentrations of REEs and a higher pH in the feed phase correlated with decreased mass transfer, while yttrium showed a greater propensity to induce third-phase formation compared to other REEs. Conditions favouring the use of linear aliphatic diluents, low extractant concentrations (5–10 v/v% D2EHPA) and the absence of modifiers also contributed to third-phase formation. The addition of tri-n-butyl phosphate (TBP) mitigated third-phase formation without evidence of synergy with D2EHPA. These findings provide key insights into formulating extraction systems that prevent third-phase formation in HFRLM processes. Full article

Soil microorganisms are crucial in global biogeochemical cycles, impacting ecosystems’ energy flows and material cycling. This study, via high-throughput sequencing in four forests—the original Larix gmelinii (Rupr.) Kuzen. forest (LG), the conifer–broad-leaved mixed Pinus sylvestris var. mongolica Litv. forest (PS), the original pure Betula platyphylla Sukaczev forest (BP), and the original pure Populus L. forest (PL) in Shuanghe National Nature Reserve, Daxing’anling mountains—explored soil microbial community structures and diversities. The results indicated that the BP and PL forests had the lowest soil bacterial ACE and Chao1 indices, and the original pure birch forest’s Shannon index was higher than that of the poplar forest. The soil’s fungal Chao1 index of the birch forest was higher than that of the larch forests. Bradyrhizobium and Roseiarcus were the dominant soil bacterial genera; the dominant soil fungal genera were Podila, Russula, and Sebacina. RDA and mantel analyses indicated that soil microbial community structures varied across forest types mainly because of the effective phosphorous and pH levels, soil’s total nitrogen level, and available phosphorus level. This study offers a scientific foundation for cold-temperate-forest ecosystem management regarding soil microbial diversity and community structural changes in different forest types. Full article

The present study deals with the fabrication of activated carbon from longan peels (LPAC) using a phosphoric acid (H₃PO₄) activation method and an evaluation of LPAC’s capability for the adsorption of Reactive Black 5 (RB5) dye from aqueous solutions. The synthesized LPAC was characterized using XRD, SEM, FT-IR, and EDX, confirming a porous, carbon-rich structure with the dominant elemental composition of carbon (85.21%) and oxygen (12.43%), and a surface area of 1202.38 m²/g. Batch adsorption experiments revealed that optimal performance was achieved at pH 3.0, with equilibrium reached after 240 min. The experimental data were well fitted to the Elovich model p, suggesting a heterogeneous adsorption process with diffusion limitations. The intraparticle diffusion model further supported a multi-stage mechanism involving both film diffusion and intraparticle transport. Isotherm studies conducted at varying temperatures (293–323 K) showed a maximum adsorption capacity exceeding 370 mg/g. The adsorption data fit best with the Freundlich (R² = 0.962) and Temkin (R² = 0.970) models, indicating multilayer adsorption on a heterogeneous surface. Thermodynamic analysis revealed that the adsorption process was spontaneous and endothermic, with ΔG° values ranging from −23.15 to −26.88 kJ/mol, ΔH° = 14.23 kJ/mol, and ΔS° = 0.127 kJ/mol×K, consistent with physisorption as the dominant mechanism. Predictive modeling using an artificial neural network (ANN) achieved superior accuracy (R² = 0.989 for RRE; R² = 0.991 for q) compared to multiple linear regression (MLR). Calculation from ANN indicated that pH and contact time were the most influential factors for RB5 removal efficiency, while initial dye concentration and temperature were most critical for adsorption capacity. Furthermore, LPAC demonstrated excellent reusability, retaining over 83% removal efficiency after five adsorption–desorption cycles. These findings confirm that LPAC is an efficient and renewable adsorbent for the treatment of RB5 dye in wastewater treatment applications. Full article