Search Results (55)

Background: Noble gases, such as argon, have been observed to exhibit cytoprotective effects. The non-anesthetic properties, abundance, and cost-effectiveness of argon suggest its clinical potential. While its efficacy in mitigating ischemia–reperfusion injury has been demonstrated in cellular and small animal models, data on its effects in large animals remain limited. This study evaluated the effects of argon inhalation on pulmonary ischemia–reperfusion injury in miniature swine with potential applications in transplantation. Methods: The left bronchial and pulmonary artery and veins were clamped for 90 min, and then the clamps were released to induce lung ischemia–reperfusion injury in 10 CLAWN miniature swine. The argon group (n = 5) inhaled a mixture of 30% oxygen and 70% argon for 360 min, whereas the control group (n = 5) inhaled a mixture of 30% oxygen and 70% nitrogen for an equivalent duration. Lung function was evaluated using chest X-ray, lung biopsies, and blood gas analysis. Results: The PaO₂/FiO₂ ratio significantly decreased in the control group 2 h post-reperfusion (568 ± 12 to 272 ± 39 mmHg), but was better preserved in the argon group (562 ± 17 to 430 ± 48 mmHg). Blood gas from the left pulmonary vein showed a superior PvO₂/FiO₂ ratio in the argon group (331 ± 40 vs. 186 ± 17 mmHg at 2 h; 519 ± 19 vs. 292 ± 33 mmHg at 2 days). Chest X-ray revealed reduced infiltration in the left lung. The lung biopsy histological scores improved in the argon group at 2 h and 2 days. Serum superoxide dismutase analysis and tissue TUNEL assays suggested that antioxidant and anti-apoptotic mechanisms, respectively, were involved. Conclusions: Perioperative argon inhalation attenuates ischemia–reperfusion injury in swine lungs, likely via anti-apoptotic and antioxidant effects. Full article

This article analyzes the reactive magnetron sputtering process, using a two-element Zn-Al target, for depositing aluminum-doped zinc oxide (AZO) layers, aimed at transparent electronics. AZO films were deposited on Corning 7059 glass, flexible Corning Willow^® glass and amorphous silica substrates. To optimize the process, the study examined the target surface state across varying argon/oxygen ratios. The gas mixture significantly influenced the Al/Zn atomic ratio in the films, affecting their structural, optical and electrical performance. Films deposited at 80/20 argon/oxygen ratio—near the dielectric mode—showed high light transmission (84%) but high resistivity (47.4·10⁻³ Ω·cm). Films deposited at ratio of 84/16—close to metallic mode—exhibited lower resistivity (1.9·10⁻³ Ω·cm) but reduced light transmission (65%). The best balance was achieved with an 82/18 ratio, yielding high light transmission (83%) and low resistivity (1.4·10⁻³ Ω·cm). These findings highlight the critical role of sputtering atmosphere in tailoring AZO layer properties for use in transparent electronics. Full article

Polylactic acid (PLA) is a promising biobased polymer celebrated for its biocompatibility, biodegradability, and advantageous mechanical properties. However, its inherent hydrophobicity and lack of hydrophilic functional groups restrict its application in advanced uses, such as nonwoven fabrics (NWFs) for masks, diapers, and biomedical products. This study explores the application of cold plasma treatments to modify the surface of PLA-based NWFs using oxygen and oxygen–argon gas mixtures. We varied power levels and exposure times to optimize surface activation. The samples treated with plasma under different conditions were analyzed to understand the impact of these treatments on the surface functionalization, morphology, and thermal properties of PLA_NWF. Additionally, as a proof of concept, the plasma-treated samples were dip-coated in green tea extract, which is rich in (-)-epigallocatechin gallate (EGCG), a natural antioxidant. The findings demonstrate that plasma treatment significantly enhances the adhesion and functionality of the active ingredient, thereby paving the way for innovative sustainable applications of surface-activated PLA-NWFs in the biomedical and cosmetic sectors or food preservation. Full article

The laser pyrolysis technique was used in the synthesis of magnetic iron oxide nanopowders in the presence of ethanol vapors as a sensitizer. This technique uses the energy from a continuous-wave CO₂ laser operating at a 9.25 μm wavelength, which is transferred to the reactive precursors via the excited ethanol molecules, inducing a rapid heating of the argon-entrained Fe(CO)₅ vapors in the presence of oxygen. For a parametric study, different samples were prepared by changing the percentages of sensitizer in the reactive mixture. Moreover, the raw samples were thermally treated at different temperatures and their morpho-structural and magnetic properties were investigated. The results indicated a high degree of crystallinity (mean ordered dimension) and enhanced magnetic properties when high percentages of ethanol vapors were employed. On the contrary, at low ethanol concentrations, due to a decrease in the reaction temperature, nanoparticles with a very low size were synthesized. The raw particles have a dimension in the range of 2.5 to 10 nm (XRD and TEM). Most of them exhibited superparamagnetic behavior at room temperature, with saturation magnetization values up to 60 emu/g. The crystalline phase detected in samples is mainly maghemite, with a decreased carbon presence (up to 8 at%). In addition to the expected Fe-OH on the particles surfaces, C (and O) bearing functional groups such as C-OH or C=O that act as a supplementary hydrophilic agent in water-based suspension were detected. Using the as-synthesized and thermally treated nanopowders, water suspensions without or with hydrophilic agents (CMCNa, L-Dopa, chitosan) were prepared by means of a horn ultrasonic homogenizer at 0.5 mg/mL concentrations. DLS analyzes revealed that some powder suspensions maintained stable agglomerates over time, with a mean size of 100 nm, pH values between 4.8 and 5.3, and zeta-potential values exceeding 40 mV. All tested agents greatly improved the stability of 250–450 °C thermally treated NPs, with L-Dopa and Chitosan inducing smaller hydrodynamic sizes. Full article

This study aimed to functionalize the surface of activated carbon, and thus render the surface more hydrophilic and reactive. To attain this goal, sequential surface functionalization was carried out using (i) oxidation (pre-activation) and (ii) secondary functionalization. The carbon surface was pre-activated in an autoclave via solvothermal oxidation (i.e., wet oxidation) with nitric acid. Alternatively, plasma-assisted oxidation with a mixture of argon and oxygen (i.e., dry oxidation) was employed. A subsequent step included the reduction in formed carbonyl groups with LiAlH₄. Following that, secondary functionalization was performed with 3-(aminopropyl)trimethoxysilane (APTMS) or (3-glycidyloxypropyl)trimethoxysilane (GPTMS), respectively. Changes in the surface composition of carbon after functionalization and morphology were examined by X-ray photoelectron spectroscopy, ATR-FTIR spectroscopy, and scanning electron microscopy. Oxidized carbon samples were successfully modified at their surfaces with APMTS and GPTMS, yielding Si content of 3.2 at. % and 1.9 at. % for wet-oxidized carbon and 5.1 at. % and 2.8 at. % for dry-oxidized carbon, respectively. Full article

The noble gas argon is one of the most promising neuroprotective agents for hypoxic-reperfusion injuries of the brain. However, its effect on traumatic injuries has been insufficiently studied. The aim of this study was to analyze the effect of the triple inhalation of the argon-oxygen mixture Ar 70%/O₂ 30% on physical and neurological recovery and the degree of brain damage after traumatic brain injury and to investigate the possible molecular mechanisms of the neuroprotective effect. The experiments were performed in male Wistar rats. A controlled brain injury model was used to investigate the effects of argon treatment and the underlying molecular mechanisms. The results of the study showed that animals with craniocerebral injuries that were treated with argon inhalation exhibited better physical recovery rates, better neurological status, and less brain damage. Argon treatment significantly reduced the expression of the proinflammatory markers TNFα and CD68 caused by TBI, increased the expression of phosphorylated protein kinase B (pAKT), and promoted the expression of the transcription factor Nrf2 in intact animals. Treatment with an argon-oxygen breathing mixture after traumatic brain injury has a neuroprotective effect by suppressing the inflammatory response and activating the antioxidant and anti-ischemic system. Full article

The purpose of this study was to fully explore the mechanical properties of five different doses of an Argon–Oxygen Decarburization slag mixture in an unconfined compressive strength test. The peak stress, elastic modulus, and stress–strain curve of the mixture were studied for 90 days. Based on the experimental data and according to the theory of damage mechanics, the concept of damage threshold (t) was introduced to construct a damage constitutive model. Referring to the damage threshold of concrete, that of the mixture was determined to be 0.7 times higher than the peak strain, and the correlation coefficient between the established model and the test curve was above 0.85. These results indicate that the addition of AOD slag and fly ash can cause hydration reactions, increase the quantity of hydration products, and enhance the peak stress and elastic modulus of the mixture. The maximum increases were 94.9% and 43.1%, respectively. Parameters a and b reflect the peak stress and brittleness of the mixture, respectively. The incorporation of Argon–Oxygen Decarburization slag can make the mixture less brittle and improve its properties. The incorporation of Argon–Oxygen Decarburization slag can protect the mixture from damage. The maximum decrease is 40.2%. Full article

We performed an electrochromic investigation to optimize the composition of reactive magnetron-sputtered mixed layers of zinc oxide and tin oxide (ZnO-SnO₂). Deposition experiments were conducted as a combinatorial material synthesis approach. The binary system for the samples of SnO₂-ZnO represented the full composition range. The coloration efficiency (CE) was determined for the mixed oxide films with the simultaneous measurement of layer transmittance, in a conventional three-electrode configuration, and an electric current was applied by using organic propylene carbonate electrolyte cells. The optical parameters and composition were measured and mapped by using spectroscopic ellipsometry (SE). Scanning Electron Microscopy (SEM) and Energy-Dispersive X-ray Spectroscopy (EDS) measurements were carried out to check the SE results, for (TiO₂-SnO₂). Pure metal targets were placed separately from each other, and the indium–tin-oxide (ITO)-covered glass samples and Si-probes on a glass holder were moved under the two separated targets (Zn and Sn) in a reactive argon–oxygen (Ar-O₂) gas mixture. This combinatorial process ensured that all the compositions (from 0 to 100%) were achieved in the same sputtering chamber after one sputtering preparation cycle. The CE data evaluated from the electro-optical measurements plotted against the composition displayed a characteristic maximum at around 29% ZnO. The accuracy of our combinatorial approach was 5%. Full article

Thermogravimetry coupled with thermal analysis and quadrupole mass spectroscopy TGA/DTA-QMS were primarily used to assess the oxidation susceptibility of a pool of nanocrystalline powders of the semiconductor kesterite Cu₂ZnSnS₄ for prospective photovoltaic applications, which were prepared via the mechanochemically assisted synthesis route from two different precursor systems. Each system, as confirmed by XRD patterns, yielded first the cubic polytype of kesterite with defunct semiconductor properties, which, after thermal annealing at 500 °C under neutral gas atmosphere, was converted to the tetragonal semiconductor polytype. The TGA/DTA-QMS determinations up to 1000 °C were carried out under a neutral argon Ar atmosphere and under a dry, oxygen-containing gas mixture of O₂:Ar = 1:4 (vol.). The mass spectroscopy data confirmed that under each of the gas atmospheres, a distinctly different, multistep evolution of such oxygen-bearing gaseous compounds as sulfur oxides SO₂/SO₃, carbon dioxide CO₂, and water vapor H₂O was taking place. The TGA/DTA changes in correlation with the nature of evolving gases helped in the elucidation of the plausible chemistry linked to kesterite oxidation, both in the stage of nanopowder synthesis/storage at ambient air conditions and during forced oxidation up to 1000 °C in the dry, oxygen-containing gas mixture. Full article

Stainless steel pickling sludge (SSPS) is classified as hazardous solid waste, while Argon Oxygen Decarburization (AOD) slag is challenging to utilize due to the leaching toxicity of Cr. This study introduces a novel in-line co-processing technique for AOD slag and SSPS, parallel to the steelmaking process, aimed at metal recovery, sulfur fixation, and slag detoxification: pre-treatment-AOD slag bath approach. The transformations and migrations of sulfur and metal elements, such as Fe and Cr, in the co-processed mixture were analyzed using thermogravimetric–mass spectrometry (TG-MS) and scanning electron microscopy–energy dispersive spectroscopy (SEM-EDS). The results indicated that sulfur in SSPS could be transformed from CaSO₄ to CaS under controlled low pre-reduction temperatures (below 800 °C), facilitating its stabilization in the slag and achieving a sulfur fixation rate of over 99%. Metal elements, including iron and chromium, first formed a small portion of spinel (FeCr₂O₄) during the pre-reduction phase, then Fe-Cr or Fe-Cr-C-based alloy particles were rapidly formed at high temperatures and in the presence of reducers in the slag bath (1550 °C), aggregating and growing spontaneously, ultimately achieving a metal recovery rate of over 95%. Furthermore, a reaction model for SSPS briquettes in the AOD slag bath was established to further reveal the mechanisms of sulfur, iron, and chromium stabilization and migration, thereby providing a basis for the harmless disposal of both materials. The product alloys are expected to be used as additives in stainless steel production, while the harmless slag could be safely utilized in the preparation of cementitious auxiliary materials. Full article

To promote resourceful utilization of argon oxygen decarburization (AOD) slag, this research developed a new three-ash stabilized recycled aggregate with AOD slag, cement, fly ash (FA), and recycled aggregate (RA) as raw materials. The AOD slag was adopted as an equal mass replacement for fly ash. The application of this aggregate in a road base layer was investigated in terms of its mechanical properties and mechanistic analysis. First, based on a cement: FA ratio of 1:4, 20 sets of mixed proportion schemes were designed for four kinds of cement dosage and AOD slag replacement rates (R/%). Through compaction tests and the 7-day unconfined compressive strength test, it was found that a 3% cement dosage met the engineering requirements. Then, the unconfined compressive strength test, indirect tensile strength test, compressive rebound modulus test, and expansion rate test were carried out at different age thresholds. The results showed that the mixture’s strength, modulus, and expansion rate increased initially and then stabilized with age, while the strength and modulus initially increased and then decreased with increasing R. Secondly, based on X-ray diffraction (XRD) and scanning electron microscopy (SEM) used to analyze the mechanism, it was found that the strength, modulus, and expansion rate of the new material can be promoted by blending AOD slag, due to its ability to fully stimulate the hydration reaction and pozzolanic reaction of the binder. Finally, based on the strength and modulus results, R = 3% was identified as the optimal ratio, which provides a reference point for the effective application of AOD slag and RA in road base materials. Full article

Anion doping of tungsten trioxide by nitrogen is used to obtain electrochrome cathode materials, the spectral transmittance of which can be controlled by the doping level. A series of samples was synthesized by reactive magnetron sputtering of a metal tungsten target in a mixture of argon, nitrogen, and oxygen gases, the flow rate of the latter was varied at a constant pressure of the gas mixture. Warm-colored tungsten oxynitride films were prepared at higher doping levels with their morphology and elemental composition characterized using scanning electron microscopy, crystal structure described using X-ray diffraction and the valence state of constituents revealed with X-ray photoelectron spectroscopy techniques. Optical properties were measured by making use of transmission spectrophotometry and spectroscopic ellipsometry. These extensive experimental studies revealed an increase in absorption towards shorter wavelengths below the wavelength of 0.5 µm with an increase in the doping level. At the same time, it was found that with an increase in the doping level, partial reduction of the tungsten occurs, and the fraction of non-stoichiometric oxygen steadily increases to half of the total oxygen content. It is a common belief that the imperfection of the doped material facilitates the intercalation of the material by electrolyte ions. Full article

This paper presents the results of measurements of ignition delay times in hydrogen–oxygen mixtures highly diluted with argon. The experiments were carried out behind an incident shock wave at temperatures from 870 to 2500 K, pressures from 0.5 to 1.5 atm, and equivalence ratios from 0.1 to 2.0. The results obtained were processed in terms of the partial pressure of the combustible mixture stoichiometric part that is consumed in the combustion process. An almost linear dependence of the ignition delay time on the reciprocal value of the partial pressure was found for both rich and lean mixtures. The measured data are compared with calculations based on the previously developed kinetic model and experimental data from other authors. Full article

The often overlooked and annoying aspects of the propensity of no-oxygen semiconductor kesterite, Cu₂ZnSnS₄, to oxidation during manipulation and storage in ambient air prompted the study on the prolonged exposure of kesterite nanopowders to air. Three precursor systems were used to make a large pool of the cubic and tetragonal polytypes of kesterite via a convenient mechanochemical synthesis route. The systems included the starting mixtures of (i) constituent elements (2Cu + Zn + Sn + 4S), (ii) selected metal sulfides and sulfur (Cu₂S + ZnS + SnS + S), and (iii) in situ made copper alloys (from the high-energy ball milling of the metals 2Cu + Zn + Sn) and sulfur. All raw products were shown to be cubic kesterite nanopowders with defunct semiconductor properties. These nanopowders were converted to the tetragonal kesterite semiconductor by annealing at 500 °C under argon. All materials were exposed to the ambient air for 1, 3, and 6 months and were suitably analyzed after each of the stages. The characterization methods included powder XRD, FT-IR/UV-Vis/Raman/NMR spectroscopies, SEM, the determination of BET/BJH specific surface area and helium density (d_He), and direct oxygen and hydrogen-content analyses. The results confirmed the progressive, relatively fast, and pronounced oxidation of all kesterite nanopowders towards, mainly, hydrated copper(II) and zinc(II) sulfates, and tin(IV) oxide. The time-related oxidation changes were reflected in the lowering of the energy band gap E_g of the remaining tetragonal kesterite component. Full article

We determined the optimal composition of reactive magnetron-sputtered mixed layers of Titanium oxide and Tin oxide (TiO₂-SnO₂) for electrochromic purposes. We determined and mapped the composition and optical parameters using Spectroscopic Ellipsometry (SE). Ti and Sn targets were put separately from each other, and the Si-wafers on a glass substrate (30 cm × 30 cm) were moved under the two separated targets (Ti and Sn) in a reactive Argon-Oxygen (Ar-O₂) gas mixture. Different optical models, such as the Bruggeman Effective Medium Approximation (BEMA) or the 2-Tauc–Lorentz multiple oscillator model (2T–L), were used to obtain the thickness and composition maps of the sample. Scanning Electron Microscopy (SEM) with Energy-Dispersive X-ray Spectroscopy (EDS) has been used to check the SE results. The performance of diverse optical models has been compared. We show that in the case of molecular-level mixed layers, 2T–L is better than EMA. The electrochromic effectiveness (the change of light absorption for the same electric charge) of mixed metal oxides (TiO₂-SnO₂) that are deposited by reactive sputtering has been mapped too. Full article