Search Results (786)

The dairy industry generates significant amounts of wastewater, including microfiltration (MF) retentate, a byproduct thickened with organic and inorganic pollutants. This study focuses on the treatment of two times concentrated MF retentate using a hybrid system based on biological treatment in a sequential batch reactor (SBR) and adsorption on activated carbon. The first stage involved cross-flow microfiltration using a 0.2 µm PVDF membrane at 0.5 bar, resulting in reductions of 99% in turbidity and 79% in chemical oxygen demand (COD), as well as a partial reduction in conductivity. The second stage involved 24-h biological treatment in a sequential batch reactor (SBR) with activated sludge (activated sludge index: 80 cm³/g, MLSS 2500 mg/dm³), resulting in further reductions in COD (62%) and TOC (30%), as well as the removal of 46% of total phosphorus (TP) and 35% of total nitrogen (TN). In the third stage, the decantate underwent adsorption in a column containing powdered activated carbon (PAC; 1 g; S_(BET) = 969 m² g⁻¹), reducing the concentrations of key indicators to the following levels: COD 84%, TOC 70%, TN 77%, TP 87% and suspended solids 97%. Total pollutant retention ranged from 24.6% to 97.0%. These results confirm that the MF–SBR–PAC system is an effective, compact solution that significantly reduces the load of organic and biogenic pollutants in MF retentates, paving the way for their reuse or safe discharge into the environment. Full article

Fibrate pharmaceuticals (fibrates), as a widespread class of emerging contaminants, pose potential risks to both ecological systems and human health. The photocatalytic system based on nitrogen (N) and fluorine (F) co-doped TiO₂ nanotube arrays (NF-TNAs) provides a renewable solution for fibrate pharmaceutical removal from water, powered by inexhaustible sunlight. In this study, the degradation of two typical fibrates, i.e., bezafibrate (BZF) and ciprofibrate (CPF), under simulated sunlight irradiation through NF-TNAs were investigated. The photocatalytic degradation of BZF/CPF was achieved through combined radical and non-radical oxidation processes, while the generation and reaction mechanisms of associated reactive oxygen species (ROS) were examined. Electron paramagnetic resonance detection and quenching tests confirmed the existence of h⁺, •OH, O₂^•−, and ¹O₂, with O₂^•− playing the predominant role. The transformation products (TPs) of BZF/CPF were identified through high-resolution mass spectrometry analysis combined with quantum chemical calculations to elucidate the degradation pathways. The influence of co-existing ions and typical natural organic matters (NOM) on BZF/CPF degradation were also tested. Eventually, the ecological risk of BZF/CPF transformation products was assessed through quantitative structure–activity relationship (QSAR) modeling, and the results showed that the proposed photocatalytic system can largely alleviate fibrate toxicity. Full article

The growing environmental concerns associated with petroleum-based plastics require the development of sustainable, biodegradable alternatives. Polyhydroxyalkanoates (PHAs), a family of biodegradable bioplastics, offer a promising potential as eco-friendly substitutes due to their renewable origin and favorable degradation properties. This research investigates the use of synthetic condensate, mimicking the liquid fraction from drying and shredding of household food waste, as a viable substrate for PHA production using mixed microbial cultures. Two draw-fill reactors (DFRs) were operated under different feed organic concentrations (2.0 ± 0.5 and 3.8 ± 0.6 g COD/L), maintaining a consistent carbon-to-nitrogen ratio to selectively enrich microorganisms capable of accumulating PHAs through alternating nutrient availability and deficiency. Both reactors achieved efficient organic pollutant removal (>95% soluble COD removal), stable biomass growth, and optimal pH levels. Notably, the reactor with the higher organic load (DFR-2) demonstrated a modest increase in PHA accumulation (19.05 ± 7.18%) compared to the lower-loaded reactor (DFR-1; 15.19 ± 6.00%), alongside significantly enhanced biomass productivity. Polymer characterization revealed the formation of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV), influenced by the substrate composition. Microbial community analysis showed an adaptive shift towards Proteobacteria dominance, signifying successful enrichment of effective PHA producers. Full article

To address the slow growth rate of photosynthetic bacteria (PSB), this study introduces pantothenic acid as a biological enhancing factor. The effects of pantothenic acid on PSB proliferation and its effectiveness in treating high-concentration ammonia–nitrogen wastewater were systematically evaluated. Additionally, the effects of different culture conditions, including dark aeration, darkness, light exposure, and light aeration, on PSB growth were investigated. The results show that optimal PSB growth was achieved with 20 mg/L of pantothenic acid; however, higher concentrations of pantothenic acid inhibited bacterial growth. The addition of pantothenic acid also significantly enhanced the performance of PSB in treating high-concentration organic wastewater, increasing the removal rates of COD, ammonia nitrogen, total phosphorus, and total nitrogen to 43.0%, 94.0%, 49.7%, and 51.0%, respectively. Furthermore, a synergistic effect between dark aeration and light exposure was observed. When the time of light and dark aeration was set at 1:1, the highest PSB yield was recorded, and the removal efficiencies of COD, ammonia nitrogen, total nitrogen, and total phosphorus increased to 71.4%, 95.3%, 57.1%, and 74.7%, respectively. Through the introduction of pantothenic acid and optimization of culture mode, the rapid growth of PSB and highly efficient treatment of organic wastewater were achieved, providing a new approach for advanced wastewater treatment and resource utilization. Full article

Moroccan oil shale ash (MOSA) represents an underutilized industrial by-product, particularly in the Rif region, where its high mineral content has often led to its neglect in value-added applications. This study highlights the successful conversion of MOSA into amorphous mesoporous silica (AS-Si) using a sol–gel process assisted by polyethylene glycol (PEG-6000) as a soft template. The resulting AS-Si material was extensively characterized to confirm its potential for environmental remediation. FTIR analysis revealed characteristic vibrational bands corresponding to Si–OH and Si–O–Si bonds, while XRD confirmed its amorphous nature with a broad diffraction peak at 2θ ≈ 22.5°. SEM imaging revealed a highly porous, sponge-like morphology composed of aggregated nanoscale particles, consistent with the nitrogen adsorption–desorption isotherm. The material exhibited a specific surface area of 68 m²/g, a maximum in the pore size distribution at a pore diameter of 2.4 nm, and a cumulative pore volume of 0.11 cm³/g for pores up to 78 nm. DLS analysis indicated an average hydrodynamic diameter of 779 nm with moderate polydispersity (PDI = 0.48), while a zeta potential of –34.10 mV confirmed good colloidal stability. Furthermore, thermogravimetric analysis (TGA) and DSC suggested the thermal stability of our amorphous silica. The adsorption performance of AS-Si was evaluated using methylene blue (MB) and ciprofloxacin (Cipro) as model pollutants. Kinetic data were best fitted by the pseudo-second-order model, while isotherm studies favored the Langmuir model, suggesting monolayer adsorption. AS-Si could be used four times for the removal of MB and Cipro. These results collectively demonstrate that AS-Si is a promising, low-cost, and sustainable adsorbent derived from Moroccan oil shale ash for the effective removal of organic contaminants from aqueous media. Full article

The presence of recalcitrant organic compounds in oilfield-produced-water poses significant challenges for conventional biological treatment technologies. In this study, an Fe³⁺-augmented composite bioreactor was developed to enhance the multi-pollutant removal performance and to elucidate the associated microbial community dynamics. The Fe³⁺-augmented system achieved efficient removal of oil (99.18 ± 0.91%), suspended solids (65.81 ± 17.55%), chemical oxygen demand (48.63 ± 15.15%), and polymers (57.72 ± 14.87%). The anaerobic compartment served as the core biotreatment unit, playing a pivotal role in microbial pollutant degradation. High-throughput sequencing indicated that Fe³⁺ supplementation strengthened syntrophic interactions between iron-reducing bacteria (Trichococcus and Bacillus) and methanogenic archaea (Methanobacterium and Methanomethylovorans), thereby facilitating the biodegradation of long-chain hydrocarbons (e.g., eicosane and nonadecane). Further metabolic function analysis identified long-chain-fatty-acid CoA ligase (EC 6.2.1.3) as a key enzyme mediating the interplay between hydrocarbon degradation and nitrogen cycling. This study elucidated the ecological mechanisms governing Fe³⁺-mediated multi-pollutant removal in a composite bioreactor and highlighted the potential of this approach for efficient, sustainable, and adaptable management of produced water in the petroleum industry. Full article

This study examines the effects of polyester and denim microfibers (MFs) on aerobic granular sludge (AGS) over a 42-day period. Treatment performance, granulation, and microbial community changes were assessed at 0, 10, 70, 210, and 1500 MFs/L. Reactors with 70 MFs/L achieved rapid granulation and showed improved settling by day 9, while 0 and 10 MFs/L reactors showed delayed granule formation, which was likely due to limited nucleation and weaker shear conditions. Severe clogging and frequent maintenance occurred at 1500 MFs/L. Despite > 98% MF removal in all reactors, treatment performance declined at higher MF loads. Nitrogen removal dropped from 93% to 68%. Phosphate removal slightly increased in reactors with no or low microfiber loads (96–99%), declined in reactors with 70 or 210 MFs/L (92–91%, 89–88%), and dropped significantly in the reactor with1500 MFs/L (86–70%, p < 0.05). COD removal declined with increasing MF load. Paracoccus (denitrifiers) dominated low-MF reactors; Acinetobacter (associated with complex organic degradation) and Nitrospira (nitrite-oxidizing genus) were enriched at 1500 MFs/L. Performance decline likely stemmed from nutrient transport blockage and toxic leachates, highlighting the potential threat of MFs to wastewater treatment and the need for upstream MF control. Full article

Population growth has led to an increased volume of wastewater from industrial, domestic, and municipal sources, contaminating aquatic bodies in the state of Veracruz. This study aimed to assess the efficacy of a water treatment system incorporating a DAF stage, followed by the cultivation of a microalgal consortium to eliminate pollutants from the blended effluent. The cultivation of Nannochloropsis oculata in wastewater entailed the assessment of a single variable (operating pressure) within the DAF system, in conjunction with two supplementary variables (residence time and F:M ratio), resulting in removal efficiencies of 70% for CODt, 77.24% for CODs, 78.34% for nitrogen, and 77% for total organic carbon. The water sample was found to contain elevated levels of organic matter and pollutants, beyond the permitted limits set forth in NOM-001-SEMARNAT-2021. The obtained removal percentages indicate that the suggested physicochemical–biological process (DAF-microalgae) is a suitable method for treating mixed wastewater. This approach reduces atmospheric pollution by sequestering greenhouse gases such as carbon dioxide through the photosynthetic activity of N. oculata cells, so facilitating the production of oxygen and biomass while limiting their accumulation in the atmosphere. Full article

Nanotechnology plays an increasingly important role in the economy and human life, which means that more and more amounts of nanosubstances, including nanoparticles of metal oxides, together with wastewater, end up in the environment. This study aimed to study the impact of iron(III) oxide nanoparticles (n-Fe₂O₃), which have magnetic properties, on the efficiency of the Anammox wastewater treatment process. The results indicate that n-Fe₂O₃ in the range of low concentrations may have a positive effect on nitrogen metabolism, increasing the efficiency of NH₄-N removal to 98% in 120 min and at 30 °C. During the first 30 min of the process, when almost anaerobic conditions arose, nanoparticles of Fe₂O₃, stabilized the system by producing ROS. However, a constant control of TOC and pH is necessary because of the constant increase in the amount of organic compounds and H⁺ ions during the reaction. However, a longer contact of n-Fe₂O₃ with biomass causes the efficiency to decrease, and, as a result, the efficiency is lower compared to the system containing only Anammox. Full article

Hydrothermal liquefaction (HTL) is a thermochemical conversion process that converts wet biomass into biocrude oil, a gas phase, a solid phase, and an aqueous phase (HTL-AP). An obstacle to the development and scaling of HTL is the volume of HTL-AP produced during the process, which has high concentrations of nitrogen and carbon and cannot be disposed of in the environment without treatment. The HTL-AP is enriched with organic compounds, particularly light polar organics and nitrogenous compounds, which are inhibitory to microbial treatment in wastewater treatment plants. For this reason, the valorization of the HTL-AP is significant for the circular economy of HTL. This review synthesizes published findings on different types of treatment of the HTL-AP for the recovery of valuable nutrients and the removal of toxic compounds. This work outlines the trade-offs of the treatments to serve as a guide for future research to address these weaknesses and improve the valorization of the HTL-AP. Furthermore, this work uniquely focuses on HTL-AP treatment for recovering plant-available nitrogen, targeting its potential use as a fertilizer. The literature highlights the importance of increasing nitrogen bioavailability in HTL-AP through two-step treatments and by selecting HTL-AP derived from protein-rich feedstocks, which offer higher initial nitrogen content. According to the current state of research, further work is needed to optimize chemical and biological treatments for nutrient recovery from HTL-AP, particularly regarding treatment scale and duration. Additionally, economic analyses across different treatment types are currently lacking, but are essential to evaluate their feasibility and practicality. Full article

Urban forests provide essential ecosystem services, including improving soil health, sequestering carbon (C), and supporting biodiversity. However, the effects of anthropogenic litter and root management on soil biogeochemical processes in urban environments remain poorly understood. This study applied the Detritus Inputs and Removal Treatment (DIRT) framework to examine how aboveground and belowground organic inputs influence soil organic carbon (SOC), total nitrogen (TN), soil water content (SWC), and enzymatic activities in subtropical urban camphor tree forests in China. Six treatments were implemented: litter removal (LR), litter addition (LA), root exclusion (RE), combined litter and root removal (LR + RE), combined litter addition and root exclusion (LA + RE), and an undisturbed litter control (LC). The results showed that the LA treatment significantly enhanced SOC, TN, SWC, and key soil enzyme activities (protease, catalase, and urease) compared to the LC, highlighting the crucial role of litter in enhancing soil fertility and microbial functioning. These elevated enzyme activities suggest intensified microbial nutrient cycling and metabolic activity in response to organic matter inputs. In contrast, the combined LR + RE treatment reduced SOC and enzyme activities but unexpectedly increased TN, indicating disrupted nutrient cycling, possibly due to accelerated microbial nitrogen mineralization and decomposition of existing soil organic matter in the absence of fresh carbon inputs. The LA treatment also showed the highest carbon-to-nitrogen (C:N) ratio, reflecting a carbon-enriched environment that may favor long-term carbon stabilization. Additionally, SWC was most improved under the LA + RE treatment, suggesting its potential for enhancing soil moisture retention in urban settings. These findings underscore the complementary roles of litter and root inputs in maintaining soil health and biogeochemical balance in urban forests. The study provides insights into enzyme-mediated soil processes under varying organic input regimes and highlights the value of targeted organic matter management to enhance urban ecosystem services. Full article

Long-term irrational farming practices and low return of organic materials to the fields in the black soil area have led to reduced soil carbon and nitrogen stability and nutrient imbalance, which in turn affect soil fertility and crop yields. Straw return is an effective way to enhance soil organic matter and crop productivity, but the effects of long-term straw return under tilling practices on carbon and nitrogen sequestration and soil microbial stoichiometric equilibrium in black soil need to be further investigated. This study investigated the physical, chemical and biological properties of the 0–60 cm soil layer under deep tillage with straw return to the field (DTS), deep harrow with straw return to the field (DHS), rotary tillage with straw return to the field (RTS), no tillage with straw return to the field (NTS), and conventional tillage with straw removal (CT) on the basis of seven consecutive years of tillage pattern location trials in the black soil area of eastern Inner Mongolia. The results showed that DTS and NTS significantly increased the soil organic carbon (SOC), soil total nitrogen (TN), soil microbial biomass carbon (MBC), soil microbial biomass nitrogen (MBN) contents, and the SOC/TN ratio in the 0–40 cm soil layer, enhancing soil carbon and nitrogen sequestration capacity, while the concomitant increase in the average MBC/MBN ratio in the plow layer from 6.8 to 8.2. The soil microbial quotient increased by 29.0% and 26.2%, respectively, and the stoichiometric imbalance ratio decreased by 7.9% and 5.7%, respectively. Meanwhile, in terms of maize yield from 2018 to 2024, DTS showed the most stable and significant yield increase with 41.53%. Whereas NTS showed a higher yield increase potential with a 27.36% increase in yield as the number of years of straw return increased. Therefore, DTS and NTS are superior tillage methods to improve the quality of the black soil tillage layer, to promote soil microbial carbon and nitrogen balance, and to increase crop yields. Full article

Implementing efficient strategies for the circular recovery and reuse of nutrients from wastewaters is mandatory to meet the Green Deal objectives and Sustainable Development Goals. In this context we investigated the use of zeolitic tuff (containing chabazite and phillipsite) in the selective recovery and reuse of N from various anaerobic liquid digestates in view of their implementation in farm-scale treatment plants. We tested the method on three livestock digestates and two municipal organic solid waste digestates. Adsorption isotherms and kinetics were assessed on each digestate, and a large set of parameters, including (i) contact time, (ii) initial NH₄⁺ concentration, (iii) presence of competing ions, (iv) total solids content, and (vi) separation methods (microfiltration and clarification), were considered in the experimental design. Our results showed that the adsorption mechanism can be explained by the Freundlich model (R² up to 0.97), indicating a multilayer and heterogeneous adsorption, while the kinetic of adsorption can be explained by the pseudo-second-order model, indicating chemical adsorption and ion exchange. The efficiency in the removal of NH₄⁺ was indirectly related to the K⁺ and total solids content of the digestate. Maximum NH₄⁺ removal exceeded 90% in MSW-derived digestates and 80% within 60 min in livestock-derived digestates at a 5% solid/liquid ratio. Thermodynamic parameters confirmed favorable and spontaneous adsorption (ΔG up to −7 kJ⋅mol⁻¹). Farm-scale projections estimate a nitrogen recovery potential of 1.2 to 16 kg N⋅day⁻¹, depending on digestate type and process conditions. These findings support the application of natural zeolitic tuffs as a low-cost, chemical-free solution for ammonium recovery, contributing to sustainable agriculture and circular economy objectives. Full article

Anaerobic digestion (AD) for food waste (FW) treatment has faced many challenges, especially ammonia nitrogen, acid, and salinity inhibition at a high organic loading rate (OLR). Therefore, a systematic understanding of the issues arising during the FW AD process is a necessity under a high OLR (over 3 g-VS/L d). Primarily, in terms of ammonia nitrogen inhibition, ammonia ions inhibit methane synthesis enzymes, and free ammonia (FAN) contributes to the imbalance of microbial protons. Regulation strategies include substrate C/N ratio regulation, microbial domestication, and ammonia nitrogen removal. In addition, with regard to acid inhibition, including volatile fatty acid (VFA) and long-chain fatty acid (LCFA) accumulation, the elevated acid concentration can contribute to reactive oxygen species stress, and a solution to this includes the addition of alkaline agents and trace elements or the use of microbial electrochemical and biofortification technology and micro-aeration-based AD technology. Furthermore, in terms of salinity inhibition, high salinity can result in a rapid increase in cell osmotic pressure, which can cause cell rupture, and water washing and bio-electrochemical AD are defined as solutions. Future research directions are proposed, mainly in terms of avoiding the introduction of novel containments into these regulation strategies and applying them in large-scale AD plants under a high OLR. Full article

Potamogeton crispus (P. crispus), with strong nitrogen uptake capacity, plays an important ecological role during winter and early spring when most aquatic plants are inactive. Its presence can also influence microbial denitrification in sediments by regulating oxygen levels and organic carbon availability. In this study, an indoor hydroponic simulation system was used to systematically evaluate the effects of P. crispus under different nitrogen-loading conditions on nitrogen removal from water, changes in sediment carbon and nitrogen fractions, microbial community structure, and greenhouse gas fluxes. The results showed that P. crispus effectively removed TN, NH₄⁺-N, NO₃⁻-N, and NO₂⁻-N, maintaining strong denitrification capacity even under high-nitrogen loading. Under all nitrogen conditions, TN removal exceeded 80%, while NH₄⁺-N and NO₃⁻-N removal efficiencies surpassed 90%, with effective suppression of NO₂⁻-N accumulation. Rhizosphere-mediated regulation by P. crispus enhanced the transformation and stabilization of DOC and NO₃⁻-N in sediments, while also mitigating nitrogen-induced disturbances to carbon–nitrogen balance. The plant also exhibited strong CO₂ uptake capacity, low CH₄ emissions with a slight increase under higher nitrogen loading, and N₂O fluxes that were significantly affected by nitrogen levels—showing negative values under low nitrogen and sharp increases under high-nitrogen conditions. Correlation analyses indicated that CO₂ and N₂O emissions were mainly regulated by microbial taxa involved in carbon and nitrogen transformation, while CH₄ emissions were primarily driven by methanogenic archaea and showed weaker correlations with environmental factors. These findings highlight the importance of water restoration during low-temperature seasons and provide a theoretical basis for integrated wetland management strategies aimed at coordinated pollution reduction and carbon mitigation. Full article