Search Results (36)

In order to improve the lubrication efficiency in the bearing cavity, this study establishes a simulation model of the fluid domain of the bearing cavity based on the computational fluid dynamics (CFD) method and systematically studies the flow characteristics of the lubricant and its lubrication mechanism in the high-speed rotary bearing. In the process of high-speed bearing operation, the lubricant is subject to the combined effect of centrifugal force and contact pressure, gradually spreads to both sides of the steel ball, and forms a stable oil film after injection from the nozzle. However, due to the influence of high pressure distribution in the contact area, the actual formation of the oil film coverage is relatively limited. In order to further optimize the lubrication effect, this study focuses on investigating the influence law of different injection speeds and rotational speeds on the bearing air curtain effect. The results of the study show that when the air curtain effect is enhanced, there will be significant shear interference on the trajectory of the lubricant, which is manifested in the phenomenon of “buckling” at the end of the lubricant, thus reducing the lubrication efficiency. To address this problem, this study innovatively proposes the air curtain obstruction coefficient K as a quantitative evaluation index, and through numerical simulation, it is found that the lubricant can effectively overcome the air curtain obstruction and achieve a better lubrication coverage when the value of K is reduced to below 0.4. Based on this finding, the study further confirmed that the lubrication efficiency of bearings can be significantly improved under different operating conditions by rationally regulating the injection rate. Full article

Under the trend of lightweight and high-efficiency development in industrial equipment, precise regulation of lubrication in gear reducers is a key breakthrough for enhancing transmission system efficiency and reliability. This study establishes a three-dimensional numerical model for high-speed gear jet lubrication using computational fluid dynamics (CFD) and dynamic mesh technology. By implementing the volume of fluid (VOF) multiphase flow model and the standard k-ω turbulence model, the study simulates the dynamic distribution of lubricant in gear meshing zones and analyzes critical parameters such as the oil volume fraction, eddy viscosity, and turbulent kinetic energy. The results show that reducing the oil injection distance significantly enhances lubricant coverage and continuity: as the injection distance increases from 4.8 mm to 24 mm, the lubricant shifts from discrete droplets to a dense wedge-shaped film, mitigating lubrication failure risks from secondary atomization and energy loss. The optimized injection distance also improves the spatial stability of eddy viscosity and suppresses excessive dissipation of turbulent kinetic energy, enhancing both the shear-load capacity and thermal management. Dynamic data from monitoring point P show that reducing the injection distance stabilizes lubricant velocity and promotes more consistent oil film formation and heat transfer. Through multiphysics simulations and parametric analysis, this study elucidates the interaction between geometric parameters and hydrodynamic behaviors in jet lubrication systems. The findings provide quantitative evaluation methods for structural optimization and energy control in gear lubrication systems, offering theoretical insights for thermal management and reliability enhancement in high-speed transmission. These results contribute to the lightweight design and sustainable development of industrial equipment. Full article

For the gas injection process in the underground natural gas storage, it is of great significance to separate lubricating oil droplets from natural gas to ensure the capacity of gas injection. However, the interaction mechanism, among various factors, is still unclear in real field conditions. In this study, the filtration performances of filter elements were investigated in a range of gas temperatures from 20 °C to 70 °C, aerosol concentrations from 400 mg/m³ to 1200 mg/m³ and flowrates from 37.2 m³/h to 74.4 m³/h. The results show that at the same flowrate, the steady-state filtration efficiency decreases with increasing temperature, resulting from a shift in the upstream aerosol towards the smaller size and an increase in the concentration for droplets within the range of 0.3 to 2 μm. The filtration efficiency only increases by 0.02% at 20 °C, while the steady-state efficiency increases by more than 0.10% at 70 °C and all the flowrates. At the same gas temperature and aerosol concentration, the steady-state filtration efficiency increases with the increase in flowrate. In practical applications, the filtration performance can be improved by lowing the gas temperature, setting up fewer filter elements in the separator, and appropriately reducing the injection amount of lubricating oil. Full article

The performance improvement potential with the optimisation of vane geometry and port timing angle in oil-injected Rotary Vane Compressors (RVCs) is not yet fully understood. Commonly, studies have used single-phase CFD models without consideration of lubricating oil. However, the presented analysis uses a more complex oil–gas two-phase CFD model. A fully analytical grid generation method was used for discretisation of the rotor domain, and the numerical method was validated against the experimental results. Coupled with the analysis of the flow field, the effects of five vane parameters and four configurations of port timing angles on the compressor performance were studied. The results show that the baseline case of the RVC achieved the volumetric and adiabatic efficiencies of 95.4% and 62.3%, respectively, while the specific power was 9.47 kW/(m³·min⁻¹), which is consistent with typical industrial RVCs. The RVC as a high-efficiency compressor highly relies on the vane tip clearance size. The baseline parameters of the vane geometry and the port timing angles are relatively reasonable, and further optimisation of vane thickness, vane tip radius, vane eccentric angle, vane tip eccentric angle, intake port closing angle and exhaust port closing angle contributes to 1.7% decrease in the specific power. Overall, the structural parameter optimisation carried out in this paper, combined with the operational parameter optimisation conducted in previous studies, leads to a power reduction of 5.6%. Full article

Gears play an important role in modern machinery and are indispensable transmission components, particularly at high speeds, where lubrication is essential for the reliability and efficiency of the gear unit. In order to study the oil coverage law and heat dissipation mechanism of high-speed rotating meshing gears by injection angle, this paper adopts the moving particle semi-implicit method to establish a high-speed rotating gear lubrication model, study the intrinsic effect of different jet angles on gear lubrication, and build a gear lubrication bench for experimental verification. Numerical simulation found that with an increase in spray angle, the gear surface coverage and heat transfer coefficient of the high-speed rotating transmission gears initially increase and then decrease. They reflect the same lubrication law characteristics. When the injection angle was 90°, the surface coverage and heat transfer coefficient values were at their greatest, resulting in the best spray lubricating effect. According to the experimental results, under the conditions of 0.5 MPa injection pressure and high-speed rotation of the transmission gear with vertical injection, the lubricant covers the largest surface area of the gear and the least power loss. Simultaneously, in our previous study, we experimentally obtained the optimal parameter conditions on the basis of which we derived. The effect of nozzle diameter on jet lubrication was investigated in a previous study, and in this article, the effect of nozzle angle and distance on gear lubrication is investigated; the optimal conditions for high-speed lubrication of gears are the incident distance of 3.5 cm, incident angle of 90°, incident diameter of 1.5 mm, and gear speed of 2000 r/min, and the lubrication effect reaches the best ideal state; reduction in oil loss due to oil injection lubrication and power loss due to different parameters of the lubrication system. Lubrication design provides a theoretical foundation for the transmission system. Full article

As the world transitions to decarbonized fuels, understanding the impact of engine oil on emissions remains crucial. Lubricant-derived particulate emissions can influence air quality and regulatory compliance in future transport. Researchers have predominantly focused on transient driving cycles to replicate real-world conditions and capture the full range of particle size. This emphasis has led to a lack of comprehensive data on oil-related particulate emissions during steady-state operations, particularly for particles smaller than 23 nm. This paper addresses this gap as upcoming regulations, such as Euro 7, are expected to impose stricter limits by extending measurement thresholds down to 10 nm. The investigation was conducted on a 1.0 L gasoline direct injection engine, assessing total particulate number (TPN) emissions using three oil formulations: a baseline oil with mid-ash content and mid-volatility, a low-ash and low-volatility oil (LoLo), and a high-ash and high-volatility oil (HiHi). A DMS500, with and without a catalytic stripper, measured particle size distribution and TPN. Two digital filters were applied to obtain particle number (PN) metrics comparable to condensation particle counters: “F1-PN > 23” with d50 = 23 nm and “F3-PN > 10” with d50 = 10 nm. Sub-23 nm particles dominated emissions, with baseline oil generally producing higher PN emissions except at low loads. Using F1-PN > 23, HiHi exhibited higher PN counts across moderate to high speeds, while F3-PN > 10 revealed lower PN emissions for HiHi at specific conditions, excluding 2250 rpm-fast idle. By a weighted arithmetic mean, HiHi’s emissions were 9.7% higher than LoLo with F1-PN > 23 and 3.6% higher with F3-PN > 10. Oil formulation did not influence nucleation mode diameter. A three-way ANOVA demonstrated that load and speed were the predominant factors affecting emissions over the entire testing map; albeit at specific operating conditions the effect of the oil is evident. This suggests that under steady-state conditions, carbon-based fuel still plays a key role in particle formation. Future work will investigate decarbonised fuels to further isolate the effect of oil on emissions. Full article

Variable tooth thickness gears have significant effects on the characteristics of the flow field inside the gearbox and the lubrication efficiency under high-speed operating conditions due to their complex parameters, such as tooth profile, cone angle, rotational speed, and oil injection speed. To investigate the impact mechanism of oil injection velocity on the working flow field of high-speed variable tooth thickness gears under varying parameters, this paper establishes an oil injection lubrication model under high rotational speeds of variable tooth thickness gears, based on computational fluid dynamics (CFD) methods and the Volume of Fluid (VOF) model, combined with the dynamic mesh technique. This paper analyzes the lubrication issues at the initial oil injection moment of involute variable tooth thickness gears. By computing the lubricant distribution state at 0.1 s after the oil injection onset based on the stabilized flow field under no-oil-injection condition, discussions are conducted on the single-phase and two-phase flow fields within the gear casing at different cone angles and rotational speeds separately examining the flow states near the oil nozzle and the distribution patterns of lubricant at the meshing portions. The results indicate that, without oil injection, the pressure near the oil nozzle gradually increases with an increase in rotational speed and decreases with an increase in cone angle; at the initial oil injection moment, the lubricant volume fraction at the gear meshing portions gradually increases with an increase in rotational speed and rises with an increase in cone angle. Full article

High-speed gears are crucial transmission components found in airplanes and other systems, and they are maintained primarily through oil injection. However, due to their high operating speeds and the influence of oil injection settings, gear surface lubrication efficacy is frequently insufficient, compromising the transmission system’s precision, durability, and safety. Currently, the parameter choices for oil injection in high-speed gears mostly rely on empirical judgment, which results in significant time and resource expenses. This study focuses on one pair of internal meshing gears within a specific aircraft gearbox, establishing an oil injection lubrication model for high-speed internal meshing gears using the computational fluid dynamics (CFD) approach. This research provides insights and references for optimizing oil injection parameters and improving lubrication efficiency in high-speed internal meshing gear systems by examining the dynamic characteristics of internal meshing wind resistance in addition to the effects of injection tube position, angle, and speed on lubrication performance. Full article

This study investigates the power losses of rolling element bearings (REBs) lubricated using an oil bath. Experimental tests conducted on two different deep-groove ball bearings (DGBBs) provide valuable insights into the behaviour of DGBBs under different oil levels, generating essential data for developing accurate models of power losses. Observations of the oil bath dynamics reveal the formation of an oil ring at high oil levels, as observed for planetary gear trains, leading to modifications in the oil flow behaviour. The experiments demonstrate that oil bath lubrication generates power losses comparable to injection lubrication when the oil level is low. However, as the oil level increases, so do the power losses due to increased drag within the bearing. This study presents a comprehensive model for calculating drag losses. The proposed drag power loss model accounts for variations in oil level and significantly improves loss predictions. A comparison of existing models with the experimental results shows good agreement for both bearings, demonstrating the effectiveness of the developed model in accounting for oil bath height in loss calculations. Full article

The atomization mechanism of lubrication fluid in rolling bearings under high-speed airflow between the rings was investigated. A simulation model of gas–liquid two-phase flow in angular contact ball bearings was developed, and the jet lubrication process between the bearing rings was simulated using FLUENT computational fluid dynamics software (Ansys 19.2). The complex motion boundary conditions of the rolling elements were addressed through a layered approach. We can obtain more accurate boundary layer flow field changes and statistics of the diameter of oil particles in lubricating oil atomization, which lays the foundation for analyzing the law of influence on lubricating oil atomization. The results show that as the number of boundary layer layers increases, the influence of the boundary layer flow field on the lubricating oil is more obvious. The oil particle size is excessively flat, and the concentration of large particles of oil appears to decrease. As the speed increases, the amount of oil in the cavity decreases, but the oil droplets are also fragmented, which intensifies the atomization and reduces the particle diameter. This reduces the Sauter Mean Diameter (SMD), which is not conducive to the lubrication of the bearing. Under different injection pressures, when the injection pressure is large, it is beneficial to the lubrication of the bearing. Full article

The temperature field distribution of high-speed double-helical gears under oil injection lubrication is investigated by obtaining heat flux density and convective heat transfer coefficients through theoretical calculations and CFD (computational fluid dynamics) simulations. Based on the CFD method, fluid simulations are performed to obtain the distribution of lubricating oil on the surface of the double-helical gears, the velocity streamline diagram of the lubricating oil, and the convective heat transfer coefficients of different surfaces of the gears. The friction heat flux density is calculated using Hertzian contact theory and theoretical formula of heat generation. The double-helical gears’ steady-state temperature field simulation uses this heat flux density as a boundary condition. The correctness of the calculation method is verified through experiments. The study shows that increasing the jet velocity allows the jet to reach the tooth surface more effectively, improving the cooling effect and reducing the maximum gear temperature. However, the relationship between the jet velocity and the minimum gear temperature is non-linear. Within a certain range, increasing the jet diameter makes the jet wider, and the area covered by the lubricating oil becomes larger as the jet spreads around the gear teeth, enhancing the cooling effect. An increase in gear speed leads to an increase in frictional heat flux density; moreover, the high-velocity airflow generated by the increased speed reduces the amount of lubricant entering the mesh zone, which in turn causes the maximum temperature of the gears to continue to rise. Full article

The aim of this study was to investigate the tribological characteristics of commercially available high-strength polyphthalamide-based composites with great contents (30–50 wt.%) of both carbon and glass fibers in point and linear contacts against metal and ceramic counterfaces under dry friction and oil-lubricated conditions at various loads and sliding speeds. The lengths of both types of fibers were varied simultaneously with their contents while samples were fabricated from granules by injection molding. When loading PPA with 30 wt.% SCFs at an aspect ratio (AR) of 200, the ultimate tensile strength and the elastic modulus increased up to 142.7 ± 12.5 MPa and 12.9 ± 0.6 GPa, respectively. In the composites with the higher contents of reinforcing fibers PPA/40CCF and AR~1000, the ultimate tensile strength and the elastic modulus were 240 ± 3 MPa and 33.7 ± 1.9 GPa, respectively. Under the applied test conditions, a composite reinforced with 40 wt.% carbon fibers up to 100 μm long at an aspect ratio of ~1000 possessed the best both mechanical properties and tribological characteristics. One of the reasons that should be considered for improving the tribological characteristics of the composite is the fatigue wear mechanism, which is facilitated by the high filling degree, the strong interfacial adhesion, and the great aspect ratio for fibers. Under the oil-lubricated conditions, both friction coefficients and wear rates decreased, so such friction units could be implemented whenever possible. The reported data can be used as practical recommendations for applying fibrous polyphthalamide-based composites as friction unit components. Full article

In order to clarify the effect of mixed lubrication methods on the oil flow and power loss of the gearbox, this study adopts a high-precision moving particle semi-implicit (MPS) method to investigate the lubrication of the gearbox under the joint influence of splash lubrication and oil injection lubrication. The accuracy of the numerical method to calculate the churning torque was verified by the constructed test rig. The effects of rotational speed, immersion depth, injection volume rate, and oil injection angle were analyzed and evaluated for lubrication. The results show that better lubrication can be achieved with relatively small churning torques by using a hybrid lubrication method. This provides some references for engineering applications of gearboxes. Full article

PEEK (Poly Ether Ether Ketone) is a high-performance thermoplastic polymer with excellent mechanical, thermal and chemical stability. PEEK has good performance, and is widely used in hydraulic motors. However, there are few studies on the friction and wear properties of materials under the condition of oil lubrication with wide application. The modification of PEEK and the expansion of its application have become a hot research topic in the industry. This study focuses on the modification of the design of PEEK and explores the friction and wear characteristics of self-lubricating materials under different modification schemes. Friction and wear samples were prepared using PEEK-modification pelletizing and injection-molding processes, followed by fixed-condition friction and wear tests. The tribological mechanisms and wear properties of the materials under different modification schemes were analyzed, leading to the identification of several sets of improved reinforced materials. Experimental results demonstrate that modified materials can enhance surface tribological performance, with the best modification effect observed at an SCF filling rate of 15%. The modified PEEK material can better meet the requirements of specific applications, such as high-temperature environments, chemically aggressive environments, or applications requiring high strength and wear resistance. Full article

Resource and energy efficiency are of high importance in gearbox applications. To reduce friction and wear, an external lubricant supply like dip or injection lubrication is used to lubricate tribosystems in machine elements. This leads to the need for large lubricant volumes and elaborate sealing requirements. One potential method of minimizing the amount of lubricant and simplifying sealing in gearboxes is the self-lubrication of tribosystems using oil-impregnation of porous materials. Although well established in low-loaded journal bearings, self-lubrication of rolling-sliding contacts in gears is poorly understood. This study presents the self-lubrication method using oil-impregnated porous sinter material variants. For this, the tribosystem of gear contacts is transferred to model contacts, which are analyzed for friction and temperature behavior using a twin-disk tribometer. High-resolution surface images are used to record the surface changes. The test results show a significant increase in self-lubrication functionality of tribosystems by oil-impregnated porous sinter material and a tribo-performance comparable to injection-lubricated tribosystems of a sinter material with additionally solid lubricant added to the sinter material powder before sintering. Furthermore, the analyses highlight a significant influence of the surface finish, and in particular the surface porosity, on the overall tribosystem behavior through significantly improved friction and wear behavior transferable to gear applications. Full article