Search Results (239)

Wave deformation and sediment transport nearest the shoreside are among the main reasons for sand erosion and beach profile changes. In particular, identifying the areas of incident-wave breaking and longshore current generation parallel to the shoreline is important for understanding the morphological changes of coastal beaches. In this study, a two-phase incompressible flow model along with a sandy sloping topography was employed to investigate the wave deformation and longshore current generation areas in a circular wave basin model. The finite volume method (FVM) was implemented to discretize the governing equations in cylindrical coordinates, the volume-of-fluid method (VOF) was adopted to differentiate the air–water interfaces in the control cells, and the zonal embedded grid technique was employed for grid generation in the cylindrical computational domain. The water surface elevations and velocity profiles were measured in different wave conditions, and the measurements showed that the maximum water levels per wave were high and varied between cases, as well as between cross-sections in a single case. Additionally, the mean water levels were lower in the adjacent positions of the approximated wave-breaking zones. The wave-breaking positions varied between cross-sections in a single case, with the incident-wave height, mean water level, and wave-breaking position measurements indicating the influence of downstream flow variation in each cross-section on the sloping topography. The cross-shore velocity profiles became relatively stable over time, while the longshore velocity profiles predominantly moved in the alongshore direction, with smaller fluctuations, particularly during the same time period and in measurement positions near the wave-breaking zone. The computed velocity profiles also varied between cross-sections, and for the velocity profiles along the cross-shore and longshore directions nearest the wave-breaking areas where the downstream flow had minimal influence, it was presumed that there was longshore-current generation in the sloping topography nearest the shoreside. The computed results were compared with the experimental results and we observed similar characteristics for wave profiles in the same wave period case in both models. In the future, further investigations can be conducted using the presented circular wave basin model to investigate the oblique wave deformation and longshore current generation in different sloping and wave conditions. Full article

We propose a single-phase chiral elastic metamaterial capable of simultaneously exhibiting negative effective mass density and negative bulk modulus in the ultrasonic frequency range. The unit cell consists of a regular hexagonal frame connected to a central circular mass through six obliquely oriented, slender aluminum beams. The design avoids the manufacturing complexity of multi-phase systems by relying solely on geometric topology and chirality to induce dipolar and rotational resonances. Dispersion analysis and effective parameter retrieval confirm a double-negative frequency region from 30.9 kHz to 34 kHz. Finite element simulations further demonstrate negative refraction behavior when the metamaterial is immersed in water and subjected to 32 kHz and 32.7 kHz incident plane wave. Equifrequency curves (EFCs) analysis shows excellent agreement with simulated refraction angles, validating the material’s double-negative performance. This study provides a robust, manufacturable platform for elastic wave manipulation using a single-phase metallic metamaterial design. Full article

Using numerical simulations, this study investigated the seismic response of concrete dams when subjected to near-fault obliquely incident P waves. For comparison, several near-fault pulse-like movements with different motion parameters were selected and decomposed into non-pulse residual components. A seismic input procedure for P wave oblique incidence was developed and verified based on the viscous-spring artificial boundary theory. A finite element model of a concrete dam system was used for nonlinear time history analyses. The damage and displacement responses were analyzed under pulse-like and non-pulse motions with incident angles varying from −90° to 90°. The response differences induced by the pulse characteristics incident direction were examined. The relationship between the seismic parameters and response indices was also determined to obtain the optimal seismic parameter describing the variation under different incident conditions. Moreover, the coupled effect of the pulse feature and oblique incidence on the dynamic response and seismic behavior was examined. Finally, a nonlinear three-dimensional predictive model was proposed based on the optimal seismic parameter S_a(T₁) and incident angle, exhibiting high correlation and accuracy. The results demonstrated that incident angles between 60° and 75° (with higher spectral acceleration values) intensified the dam damage and vibration when subjected to the oblique near-fault P waves, a crucial discovery for improving the seismic design and safety measure of concrete dams located in regions prone to near-fault seismic hazards. Full article

The theory of orbital forcing as formulated by Milankovitch involves the mediation by the advance (retreat) of ice sheets and the resulting variations in terrestrial albedo. This approach poses a major problem: that of the period of glacial cycles, which varies over time, as happened during the Mid-Pleistocene Transition (MPT). Here, we show that various hypotheses are called into question because of the finding of a second transition, the Early Quaternary Transition (EQT), resulting from the million-year period eccentricity parameter. We propose to complement the orbital forcing theory to explain both the MPT and the EQT by invoking the mediation of western boundary currents (WBCs) and the resulting variations in heat transfer from the low to the high latitudes. From observational and theoretical considerations, it appears that very long-period Rossby waves winding around subtropical gyres, the so-called “gyral” Rossby waves (GRWs), are resonantly forced in subharmonic modes from variations in solar irradiance resulting from the solar and orbital cycles. Two mutually reinforcing positive feedbacks of the climate response to orbital forcing have been evidenced: namely the change in the albedo resulting from the cyclic growth and retreat of ice sheets in accordance with the standard Milankovitch theory, and the modulation of the velocity of the WBCs of subtropical gyres. Due to the inherited resonance properties of GRWs, the response of the climate system to orbital forcing is sensitive to small changes in the forcing periods. For both the MPT and the EQT, the transition occurred when the forcing period merged with one of the natural periods of the climate system. The MPT occurred 1.25 Ma ago, when the dominant period shifted from 41 ka to 98 ka, with both periods corresponding to changes in the Earth’s obliquity and eccentricity. The EQT occurred 2.38 Ma ago, when the dominant period shifted from 408 ka to 786 ka, with both periods corresponding to changes in the Earth’s eccentricity. Through this paradigm shift, the objective of this self-consistent approach is essentially to spark new debates around a problem that has been pending since the discovery of glacial–interglacial cycles, where many hypotheses have been put forward without, however, fully answering all our questions. Full article

Rip currents at featureless beaches (i.e., beaches lacking sandbars or channels) are often hydrodynamically controlled, exhibiting intermittent and unpredictable behaviors that pose significant risks to recreational beach users. This study assessed occurrences of rip currents under a range of idealized morphology configurations and hydrodynamic wave forcing parameters using a wave-resolving Boussinesq-type model. Numerical experiments revealed that rip currents with durations on the time scale of 10 min are generated in the forms of vortex pairs, intensified eddies, mega-rips, and eddies shedding from longshore currents. In general, the key conditions that promote rip current formation at featureless beaches include shoreline curvature, headlands, moderately mild beach slopes (e.g., 0.02–0.03), normal or near-normal wave incidence, and large wave heights. Most importantly, this study highlights inherent uncertainties in rip current occurrences, particularly under conditions usually perceived as low risk: low wave heights, short wave periods, oblique wave incidence, and straight shorelines. These conditions can lead to transient rip currents and pose an unexpected hazard that coastal communities should be aware of. Full article

In this paper, we design an ultra-thin broadband transparent absorber based on indium tin oxide (ITO) film, and we choose polymethyl methacrylate (PMMA) high-transmittance dielectric sheet instead of the traditional dielectric sheet and polyethylene glycol terephthalate (PET) as the ITO film substrate. Simulation results indicate that the absorber achieves more than 90% absorption for positively incident electromagnetic waves in the broadband range of 5–21.15 GHz with a fractional bandwidth (FBW) of 123.5% and a thickness of 6.3 mm (0.105 λ_L, where λ_L is the wavelength at the lowest frequency). Meanwhile, this paper introduces the interference theory to explain the broadband absorption mechanism of the absorber, which makes up for the defect that the equivalent circuit model (ECM) method cannot analyze the oblique incidence electromagnetic wave. This paper also compares the HFSS simulation results, ECM theoretical values, and interference theoretical values under positively incident electromagnetic waves to clarify the advantages of interference theory in the design of wave absorbers. Full article

An analytical hydroelastic model formulation in three-dimensional and oblique wave cases is developed to analyze the dynamic response of a horizontal, floating elastic plate subject to wave-current interaction under linearized small-amplitude wave theory. The floating elastic plate is moored to the bottom bed and free to the channel walls. Green’s function’s technique is utilised to determine the dispersion relation in 3D, and the series form of Green’s function in different water depths is derived in the oblique wave case. Further, the comparative analysis of phase and group velocities for different wave angles, between the present the existing models, is discussed. The derived dispersion relation is used in the solution by applying the geometrical symmetry velocity decomposition method. The present theoretical results of wave quantities are validated with the recently published and existing numerical hydroelastic model. A comparative analysis revealed a 1.7% difference between the present model and the existing hydroelastic models, and a 7.7% difference when compared to the model’s limiting cases. Several numerical results of the wave quantities, wave force, and vertical displacements are conducted to investigate the influence of current velocity on the hydroelastic response in three dimensions. It has been noted that the value of reflection coefficient diminishes for larger values of current velocity and the vertical displacement correspondingly becomes greater. This analysis will inform the design of elastic plate-based wave energy converters and breakwaters by clarifying how current loads affect the hydroelastic of a floating elastic plate with an oblique angle and three dimensions. Full article

A causal electromagnetic (EM) metasurface is backed by a lossless substrate and partially absorbs obliquely incoming rays. The integral of the absorbed power along the entire frequency axis is analytically evaluated, and the obtained sum rules indicate the global absorption by such a generic configuration. The beneficial influence of the plasma frequency and damping factor on the total absorbance score as well as the opposite effect of the angle of excitation, is noted. An overall lossless behavior at the incidence direction where the propagating waves into the substrate turn into evanescent is identified, once the magnetic field is parallel to the interface. The reported results can be useful in the tailoring of spectrally dependent absorption by a whole class of planar structures and, accordingly, in the forward and inverse design of lossy photonic metasurface setups. Full article

Metasurfaces, as subwavelength planar structures, offer unprecedented electromagnetic wavefront manipulation capabilities. However, most existing focusing metasurfaces operate in a single polarization mode, support only one focusing function, or rely on complex multi-unit configurations, limiting their versatility in practical applications. This study proposes a dual-polarization multiplexed transmissive focusing metasurface operating at 5.8 GHz. Through theoretical analysis and full-wave simulations, the electromagnetic response of the metasurface unit is systematically investigated. To overcome the limitations of conventional transmissive units, an anisotropic low-profile unit is designed using a hybrid stacking strategy that combines dielectric substrates and an air layer, achieving a compact profile of only 0.16λ. This unit achieves 360° phase modulation with a transmission magnitude exceeding 0.85 while being lightweight and cost-effective. Based on the unit, three metasurface arrays are developed to achieve various focusing functions, including single-point offset focusing, dual-point focusing, and multi-focal energy-controlled focusing, offering over 15% operational bandwidth and maintaining satisfactory performance under a 25° oblique incidence, with respective efficiencies of 35.59%, 25.11%, and 33.42%. This work provides a novel solution for multifunctional focusing applications, expanding the potential of metasurfaces in wireless communication, wireless power transfer, and beyond. Full article

With the rapid development of 5G communication technology, there is an increasing demand for high-performance antennas and beam control technologies, making the development of novel metamaterial structures capable of precise electromagnetic wave manipulation a current research hotspot. This paper presents a coding metasurface specifically designed for 5G communication applications, operating at a frequency of 3.5 GHz. The design employs a unique annular metasurface unit structure capable of achieving both single-beam and dual-beam functionalities. Through convolution operations, precise control over the reflection angle is achieved, with an adjustable range from 51.5° to 17.5° and a resolution of 10°. This design overcomes the inherent limitations of traditional gradient coding methods, providing a comprehensive framework for wide-angle reflection control in metasurface design. The research results demonstrate that the coding metasurface can effectively control the reflection direction of electromagnetic waves at 3.5 GHz, exhibiting dual-polarization modulation capabilities and maintaining stable performance under oblique incidence conditions within 20°. Experimental validation confirms the beam control functionality of the design in real-world environments, highlighting its potential to enhance signal reception sensitivity and transmission efficiency in 5G wireless communications. This work opens new avenues for research in reconfigurable and intelligent metasurfaces, with potential applications extending beyond 5G to future 6G networks and Internet of Things (IoT) systems. Full article

In the present study, abilities of various macroscopic models (Navier–Stokes–Fourier, Burnett, original and regularized Grad’s 13-moment equations) in predicting the nonequilibrium molecular velocity distribution are examined. The results of the local distribution function reconstruction from flow macroparameters for the models considered are compared with each other and with the reference solution. Two different flows are considered: normal shock wave and stationary regular reflection of oblique shock waves. The Direct Simulation Monte Carlo method is used to obtain the reference solution and the flow macroparameters required for the distribution function reconstruction. All models under consideration predict the distribution function in the upstream low-density region rather poorly, with strong oscillations and unphysical negative values (especially regularized Grad’s 13-moment equations). In the high-density downstream region, the shape of the reference distribution is close to equilibrium, and all macroscopic models predict it rather accurately. Full article

The ongoing research in Environmental Scanning Electron Microscopy (ESEM) is contributed to in this paper. Specifically, this study investigates supersonic flow in a nozzle aperture under low-pressure conditions at the continuum mechanics boundary. This phenomenon is prevalent in the differentially pumped chamber of an ESEM, which separates two regions with a significant pressure gradient using an aperture with a pressure ratio of approximately 10:1 in the range of 10,000 to 100 Pa. The influence of nozzle wall roughness on the boundary layer characteristics and its subsequent impact on the oblique shock wave behavior, and consequently, on the static pressure distribution along the flow axis, is solved in this paper. It demonstrates the significant effect of varying inertial-to-viscous force ratios at low pressures on the resulting impact of roughness on the oblique shock wave characteristics. The resulting oblique shock wave distribution significantly affects the static pressure profile along the axis, which can substantially influence the scattering and loss of the primary electron beam traversing the differential pumping stage. This, in turn, affects the sharpness of the resulting image. The boundary layer within the nozzle plays a crucial role in determining the overall flow characteristics and indirectly affects beam scattering. This study examines the influence of surface roughness and quality of the manufactured nozzle on the resulting flow behavior. The initial results obtained from experimental measurements using pressure sensors, when compared to CFD simulation results, demonstrate the necessity of accurately setting roughness values in CFD calculations to ensure accurate results. The CFD simulation has been validated against experimental data, enabling further simulations. The research combines physical theory, CFD simulations, advanced experimental sensing techniques, and precision manufacturing technologies for the critical components of the experimental setup. Full article

In a supersonic flow, disturbances of different parameters arise. These perturbations can have a significant impact on the interaction of the flow with the surface. When gas flow passes through a shock wave, perturbations are transformed depending on the initial parameters of the flow. Therefore, it is important to be able to correctly assess the intensity of these transformations. In this work, for the first time, a method has been proposed that allows us to estimate the dynamics of variation of disturbances of flow parameters when passing through an oblique shock wave. The influence of the shock wave inclination angle β, Mach number, intensity of disturbances of velocity, density, temperature, and pressure in front of the shock wave on perturbations of the flow parameters behind the shock wave was investigated. The Mach numbers ranged from 1.2 to 10 and the shock wave inclination angle varied from 15° to 90°. It was shown that the interaction of a supersonic gas flow with an oblique shock wave has a significant effect on the transformation of the perturbations of the flow parameters. The perturbations of temperature and pressure behind the shock wave increase significantly with the increasing angle β and Mach number in front of the shock wave. With the increasing Mach number, the velocity perturbations behind the shock wave first increase, then decrease, passing through a maximum, and afterwards the flow becomes more stable. Full article

The transmittance characteristics and the band structure of photonic heterostructures consisting of four distinct dielectric materials are analyzed using the transfer matrix method. An enhanced band structure of such crystals is discovered. It is shown that the band structure is strongly influenced by the arrangement of unit cells in the periodic building blocks of the crystals. The transmission spectra are evaluated for varying layer thicknesses and incident angles to investigate their impact on wave propagation. The symmetrical results for periodicities, sub-layer thickness, and oblique incident angles indicate robust bandgaps with blue shifting and enhanced transmission. Moreover, the periodicity in different cases, followed by the period, has also shown to have a great impact on the emergence of multiple bandgaps. The photonic bandgap and frequency are associated with the lattice elements of the unit cell, shifting naturally as a fundamental property of the structure, which has been achieved by the alteration of unit cells. Hence, the proposed photonic heterostructures offer significant potential for developing efficient band-stop and band-pass filters, facilitating their use in multi-functional integrated optical circuits within the Terahertz spectrum. Full article

To measure the angles of oblique surface cracks on a specimen, the method of using the time difference between the reflected and scattered waves generated by the interaction of the surface waves and the crack is proposed. Based on the reflection and scattering waves’ paths at the surface crack, an analytical equation that involves the crack depth, width, and inclined angle is developed. On the basis of establishing the ratio of width to depth, ∆t-φ curves and estimated error images without the width term can be analyzed in detail. The finite element simulation and experimental results for aluminum alloy samples show that a crack’s angle can be detected using the time difference method. The effects of the width term in the analytical equation on the estimated angles of the surface cracks are also verified. Measurement of the quantitative angle of inclined surface cracks is first regarded as a multiparameter inversion problem. The simulation and the experimental discussion of the interrelation between the depth, width, and angle of the inclined surface crack in this work are very meaningful for quantitative determination using laser ultrasound. Full article