Search Results (108)

The development of efficient and stable oxygen evolution reaction (OER) electrocatalysts based on non-precious metals is pivotal for advancing sustainable energy conversion technologies. We present a facile and green strategy for synthesizing a high-performance HO-CDs-FeOOH/NF(D) composite catalyst by leveraging a synergistic system of FeCl₃/urea deep eutectic solvent (DES) and hydroxyl-functionalized carbon dots (HO-CDs). This system orchestrates the rapid, in situ growth of FeOOH on nickel foam (NF) via simple immersion, wherein the DES acts as both an etchant and an iron source, while the HO-CDs induce a morphological transformation from sheet-like to granular stacking, thereby constructing highly active interfaces and increasing the density of accessible catalytic sites. The optimized catalyst exhibits exceptional OER performance, requiring an overpotential of only 251 mV to achieve 50 mA cm⁻², with a Tafel slope of 55.4 mV dec⁻¹. Moreover, it demonstrates outstanding stability, maintaining 98% of its initial current density after 24 h of continuous operation and showing negligible performance decay after 3000 cycles. This work presents a straightforward approach for designing high-performance Fe-based electrocatalysts through carbon dot-mediated morphology control via a facile DES-based impregnation strategy. Full article

Metal–organic framework (MOF) materials were extensively studied in the removal of pollutants in wastewater. However, catalysts in the powder form usually suffered from the strong tendency to agglomerate and the intricate operation for recycling, which significantly limited their practical application. In comparison, monolithic catalysts with their high macroscopic operability and recoverability as well as impressive specific surface area have attracted tremendous attention in recent years. To address these issues, a monolithic Fe-based catalyst was prepared via in situ synthesis, using nickel–iron foam (NFF) as the substrate with cobalt (Co) incorporation. XPS analysis showed that Co doping enhanced the synergistic interaction among Fe, Ni, and Co, accelerating the redox cycle among species, thus improving electron transfer and laying a kinetic foundation for efficient peroxymonosulfate (PMS) activation. Quenching experiments and EPR indicated singlet oxygen (¹O₂) as the main reactive species; Co doping shifted the degradation pathway from radicals to non-radicals. Under optimized conditions (PMS: 0.08 mmol/L; catalyst: 1 cm²; initial Chlortetracycline (CTC): 50 mg/L), 95.7% CTC degradation was achieved within 60 min, and efficiency only dropped to 90.5% after 5 cycles. This catalyst provided theoretical and technical support for the application of monolithic MOF-derived catalysts and highly efficient PMS activators. Full article

The oxygen evolution reaction (OER) in water splitting involves complex multi-electron–proton transfer processes and represents the rate-determining step limiting overall electrolysis efficiency. Developing non-noble-metal catalysts with high activity and stability is therefore essential. Herein, a heterogeneous synthesis strategy was employed to in situ construct an iron-rich layered sulfate precursor (Fe_0.42Co_0.58-SO₄/NF) on nickel foam, which underwent deep self-reconstruction in alkaline electrolyte to form nanoflower-like Fe_0.42Co_0.58OOH/NF. The optimized catalyst maintained its iron-rich composition and hierarchical structure, delivering outstanding OER performance with an overpotential of 220 mV at 10 mA·cm⁻², a Tafel slope of 31.9 mV·dec⁻¹, and stability exceeding 12 h at 600 mA·cm⁻². Synchrotron analyses revealed dynamic transitions between mono-μ-O and di-μ-O Fe–M (M = Fe, Co) oxygen bridges during reconstruction, which enhanced both structural robustness and active-site density. The Fe-rich environment promoted the formation of Fe³⁺–O–Fe³⁺ units that synergized with Co⁴⁺ species to activate the lattice oxygen mechanism (LOM), thereby accelerating OER kinetics. This work elucidates the key role of oxygen-bridge geometry in optimizing catalytic activity and durability, providing valuable insights into the rational design of Fe–Co-based non-noble-metal catalysts with high iron content for efficient water oxidation. Full article

Nickel–iron (Ni-Fe) catalysts are widely used in industry due to their cost-effectiveness and versatile catalytic properties. This work investigates the structural and morphological characteristics of Ni-Fe catalysts supported on γ-Al₂O₃, synthesized with varying Ni/Fe atomic ratios (from 1:1 to 20:1). The catalysts were characterized using a combination of experimental techniques including X-ray fluorescence (XRF), X-ray diffraction (XRD), scanning and transmission electron microscopy (SEM/TEM), and selected-area electron diffraction (SAED). Theoretical modeling using the USPEX evolutionary algorithm complemented the experimental data by predicting stable Ni-Fe crystal structures. The results revealed uniform metal distribution on the support with particle sizes ranging from 4.1 to 4.5 nm. SAED analysis confirmed the formation of an intermetallic FeNi phase, particularly in samples with higher iron content. This study demonstrates Ni-Fe interaction effects and will be of interest to researchers in catalysis and materials science working on the development of bimetallic systems. Full article

Naproxen (NPX), a nonsteroidal anti-inflammatory drug, is considered an emerging contaminant due to its persistence and potential environmental risks. In this study, NPX degradation was investigated through ozonation using nickel–iron foam (NiFeF) and NiO-modified NiFeF (NiO/NiFeF). The effect of the foam size was investigated using three configurations: S1 (1 cm × 2.5 cm), S2 (2 cm × 2.5 cm), and S3 (2 cm × 5 cm). Complete NPX removal was achieved in all systems, with degradation times of 4 min for ozonation alone, 2 min for NiFeF-S1, and 1 min for NiO/NiFeF-S2 and NiO/NiFeF-S3. The NiO/NiFeF catalyst was synthesized via ultrasonic spray pyrolysis, resulting in a porous structure with abundant active sites. Compared with conventional ozonation, NiO/NiFeF-S1 improved the total organic carbon (TOC) removal rate by 6.2-fold and maintained 87.5% of its activity after five reuse cycles, demonstrating excellent stability. High-resolution mass spectrometry revealed that catalytic ozonation generated fewer by-products (22 vs. 27 for ozonation alone) and promoted more selective pathways, including demethylation, ring-opening oxidation, and partial mineralization to CO₂ and H₂O. This enhanced performance is attributed to the synergy between NiO and NiFeF, which facilitates reactive oxygen species generation and electron transfer. These results demonstrate the potential of NiO/NiFeF as an efficient and stable catalyst for pharmaceutical removal from water. Full article

Despite intense interest in the catalytic potential of transition metal oxide heterostructures, originating from their large surface area and tunable chemistry, the fabrication of well-defined multicomponent oxide coatings with controlled architectures remains challenging. Here, we demonstrate a simple and effective swelling-assisted sequential infiltration synthesis (SIS) strategy to fabricate hierarchically porous multicomponent metal-oxide electrocatalysts with tunable bimetallic composition. A combination of solution-based infiltration (SBI) of transition metals, iron (Fe), nickel (Ni), and cobalt (Co), into a block copolymer (PS73-b-P4VP28) template, followed by vapor-phase infiltration of alumina using sequential infiltration synthesis (SIS), was employed to synthesize porous, robust, conformal and transparent multicomponent metal-oxide coatings like Fe/AlO_x, Fe+Ni/AlO_x, and Fe+Co/AlO_x. Electrochemical assessments for the oxygen evolution reaction (OER) in a 0.1 M KOH electrolyte demonstrated that the Fe+Ni/AlO_x composite exhibited markedly superior catalytic activity, achieving an impressive onset potential of 1.41 V and a peak current density of 3.29 mA/cm². This superior activity reflects the well-known synergistic effect of alloying transition metals with a trace of Fe, which facilitates OER kinetics. Overall, our approach offers a versatile and scalable path towards the design of stable and efficient catalysts with tunable nanostructures, opening new possibilities for a wide range of electrochemical energy applications. Full article

Waste lithium-ion batteries (LIBs), which usually contain dangerous organic electrolytes and transition metals, including nickel, cobalt, iron, and manganese, can hurt the environment and human health. Substantial advancements have been achieved in employing high-efficiency, economical, and environmentally sustainable techniques for the recycling of spent LIBs. Converting exhausted LIBs into efficient energy conversion catalysts straightforwardly is a good strategy for addressing metal resource constraints and clean energy concerns. This transforms waste cathodes, anodes, binders, and separators from depleted LIBs into electrocatalysts free of platinum group metals for the oxygen evolution reaction (OER) and the oxygen reduction reaction (ORR). The composite, including transition metal oxide, graphene oxide, and carbon mass, will be synthesized from spent LIBs, demonstrating enhanced electrocatalytic activity. Utilizing “waste-to-energy” methods for used LIBs as catalysts would provide substantial benefits in environmental preservation and the effective production of functional materials in metal–air batteries. Full article

Doping a third element or external functional components into binary alloy nanostructured catalysts typically significantly enhances their electrocatalytic performance. This study demonstrates that doping nickel selenide (NiSe₂) with approximately $10 \mathrm{a}\mathrm{t}\%$ iron (Fe) is an effective strategy for improving its oxygen evolution reaction (OER) catalytic activity. The resulting Ni_0.9Fe_0.1Se₂ undergoes a structural transformation from its original nanodendritic morphology and exhibits outstanding OER catalytic performance in alkaline media. It achieves a low overpotential of $231 \mathrm{m}\mathrm{V}$ at a current density of $10 \mathrm{m}\mathrm{A} {\mathrm{c}\mathrm{m}}^{-2}$, which is approximately $30\%$ lower than that of NiSe₂ ($301 \mathrm{m}\mathrm{V}$). The Tafel slope of Ni_0.9Fe_0.1Se₂ is $116 \mathrm{m}\mathrm{V} {\mathrm{d}\mathrm{e}\mathrm{c}}^{-1}$. However, degradation observed after 5 h of stability testing suggests that the doping process requires further optimization. Full article

A comprehensive literature review highlights how the nature of active metals, support materials, promoters, and synthesis methods influences catalytic performance, with particular attention to ruthenium-based catalysts as the current benchmark. Kinetic models are presented to describe the reaction pathway and predict catalyst behavior. Various reactor configurations, including fixed-bed, membrane, catalytic membrane, perovskite-based, and microreactors, are evaluated in terms of their suitability for ammonia decomposition. While ruthenium remains the benchmark catalyst, alternative transition metals such as iron, nickel, and cobalt have also been investigated, although they typically require higher operating temperatures (≥500 °C) to achieve comparable conversion levels. At the industrial scale, catalyst development must balance performance with cost. Inexpensive and scalable materials (e.g., MgO, Al₂O₃, CaO, K, Na) and simple preparation techniques (e.g., wet impregnation, incipient wetness) may offer lower performance than more advanced systems but are often favored for practical implementation. From a reactor engineering standpoint, membrane reactors emerge as the most promising technology for combining catalytic reaction and product separation in a single unit operation. This review provides a critical overview of current advances in ammonia decomposition for hydrogen production, offering insights into both catalytic materials and reactor design strategies for sustainable energy applications. Full article

Electrochemical water splitting for hydrogen production is considered a key pathway for achieving sustainable energy conversion. However, the sluggish reaction kinetics of the oxygen evolution reaction (OER) and high overpotentials severely hinder the large-scale application of water electrolysis technology. Nickel–iron layered double hydroxide (NiFe-LDH) has gained attention as a promising non-precious metal OER catalyst due to its abundant active sites and good intrinsic activity. However, its relatively low conductivity and charge transfer efficiency limit the improvement of catalytic performance. Therefore, this study used a simple hydrothermal method to generate a NiFe-LDH/Cs_0.32WO₃ heterojunction composite catalyst, relying on the excellent electronic conductivity of Cs_0.32WO₃ to improve overall charge transfer efficiency. According to electrochemical testing results, the modified NiFe-LDH/Cs_0.32WO₃-20 mg achieved a low overpotential of 349 mV at a current density of 10 mA cm⁻², a Tafel slope of 67.0 mV dec⁻¹, and a charge transfer resistance of 65.1 Ω, which represent decreases of 39 mV, 23.1%, and 40%, respectively, compared to pure NiFe-LDH. The key to performance improvement lies in the tightly bonded heterojunction interface between Cs_0.32WO₃ and NiFe-LDH. X-ray photoelectron spectroscopy (XPS) shows a distinct interfacial charge transfer phenomenon, with a notable negative shift of the W4f peak (0.85 eV), indicating the directional transfer of electrons from Cs_0.32WO₃ to NiFe-LDH. Under the influence of the built-in electric field within the heterojunction, this interfacial charge redistribution improved the electronic structure of NiFe-LDH, increased the proportion of high-valent metal ions, and significantly enhanced the OER reaction kinetics. This study provides new insights for the preparation of efficient heterojunction electrocatalysts. Full article

Nowadays, nanosized mesoporous oxides are of increasing interest to scientists. They can be used as components of heterogeneous catalysts, for photo- and electrocatalysis, as gas sensors, etc. For instance, the desired properties in catalysts include a nano size and homogeneity of the particles that form the catalyst. The particle sizes of oxides are set at the initial stage of their formation, as precursors of precipitation in the context of wet chemistry. The creation of optimal conditions is possible through the use of homogeneous precipitation, where the precipitant is formed within the solution itself as a result of a hydrolysis reaction. The resolution of this issue involved the utilization of urea in our experimental setup, obtaining the hydrolysis products of ammonia and carbon dioxide. Consequently, precipitation reactions can be utilized to obtain hydroxides, carbonates, or hydroxy carbonates of metals. The precursors were calcined, obtaining nanosized mesoporous oxides, which can have a wide range of applications. Nanosized 0.1–50 nm metal oxides were obtained, including those aluminum, iron, indium, zinc, nickel, and cobalt. Full article

Anion exchange membrane (AEM) water electrolysis is a potentially inexpensive and efficient source of hydrogen production as it uses effective low-cost catalysts. The catalytic activity and performance of nickel iron oxide (NiFeO_x) catalysts for hydrogen production in AEM water electrolyzers were investigated. The NiFeO_x catalysts were synthesized with various iron content weight percentages, and at the stoichiometric ratio for nickel ferrite (NiFe₂O₄). The catalytic activity of NiFeO_x catalyst was evaluated by linear sweep voltammetry (LSV) and chronoamperometry for the oxygen evolution reaction (OER). NiFe₂O₄ showed the highest activity for the OER in a three-electrode system, with 320 mA cm⁻² at 2 V in 1 M KOH solution. NiFe₂O₄ displayed strong stability over a 600 h period at 50 mA cm⁻² in a three-electrode setup, with a degradation rate of 15 μV/h. In single-cell electrolysis using a X-37 T membrane, at 2.2 V in 1 M KOH, the NiFe₂O₄ catalyst had the highest activity of 1100 mA cm⁻² at 45 °C, which increased with the temperature to 1503 mA cm⁻² at 55 °C. The performance of various membranes was examined, and the highest performance of the tested membranes was determined to be that of the Fumatech FAA-3-50 and FAS-50 membranes, implying that membrane performance is strongly correlated with membrane conductivity. The obtained Nyquist plots and equivalent circuit analysis were used to determine cell resistances. It was found that ohmic resistance decreases with an increase in temperature from 45 °C to 55 °C, implying the positive effect of temperature on AEM electrolysis. The FAA-3-50 and FAS-50 membranes were determined to have lower activation and ohmic resistances, indicative of higher conductivity and faster membrane charge transfer. NiFe₂O₄ in an AEM water electrolyzer displayed strong stability, with a voltage degradation rate of 0.833 mV/h over the 12 h durability test. Full article

Catalytic CO₂ methanation represents a promising process route for converting carbon dioxide into methane, a valuable energy carrier. This study investigates the performance of Ni-based catalysts on mixed silica and MgO support materials for CO₂ methanation. Silica was derived from rice husk (SiO₂(RH)), representing a sustainable, cost-effective source for catalyst support, and MgO was used as a reference and to enhance the catalytic activity of the Ni-based catalysts through admixture with SiO₂(RH). The results were compared to CO₂ methanation over Ni-based catalysts on reduced iron ore from natural siderite (siderite_reduced), providing another abundant source for catalyst support. The experiments were conducted in a tubular reactor with a feed gas composition of H₂:CO₂:N₂ = 56:14:30, feed gas flow rates ranging from 4.01 to 14.66 m³·kg⁻¹·h⁻¹ (STP), and reaction temperatures of 548–648 K. The highest CO₂ conversion with the Ni/SiO₂(RH) catalyst was 39.01% at a methane selectivity of 92.64%. The use of mixed silica and MgO supports (SiO₂(RH)/MgO) for nickel revealed a beneficial effect, enhancing CO₂ conversion and methane formation. In this case, methane selectivities consistently exceeded 91.57%. Superior methane selectivity and CO₂ conversion were obtained with Ni/MgO catalysts and Ni/SiO₂(RH)/MgO catalysts with high MgO fractions, highlighting the fundamental effect of MgO in the catalyst support for CO₂ methanation. Full article

In this study, catalytically active coatings on titanium were synthesized by plasma electrolytic oxidation (PEO) in aqueous electrolytes based on sodium tungstate with the addition of sodium phosphate or sodium borate and chelate complexes of iron, cobalt or nickel. Taking into account the EDX, XPS and XRD data, the oxide–phosphate coatings (PWFe, PWCo, PWNi) contained crystalline titanium oxide and amorphous tungstates and/or phosphates of iron triad metals. Amorphization was facilitated by high phosphorus concentrations (up to 6 at.%). Replacing phosphate with borate in the electrolyte with Ni(II)-EDTA complexes led to the crystallization of WO₃ and NiWO₄ in the PEO coatings (BWNi). All formed PEO coatings were active in reactions of the oxidative desulfurization (ODS) of thiophene and dibenzothiophene and oxidative denitrogenation (ODN) of pyridine, as well as in the simultaneous removal of S- and N-containing substrates from their mixture. The stability of samples with MWO₄ increased in the following series: PWNi < PWCo < PW < PWFe < BWNi. Replacing phosphate with borate in the electrolyte resulted in the preparation of catalysts with enhanced stability and activity. In contrast to PWM catalysts, the BWNi catalyst had selectivity toward the oxidation of pyridine in its mixture with thiophene. Full article

Nickel-doped iron oxide/graphene oxide powders were synthesized by the co-precipitation method varying the Ni/Fe ratio, and the activity of the materials towards the oxygen reduction reaction in a microbial fuel cell (MFC) was studied. The samples presented X-ray diffraction peaks associated with magnetite, maghemite and Ni ferrite, as well as evidence of hematite. Raman spectra confirmed the presence of maghemite (γ-Fe₂O₃) and NiFe₂O₄. Scanning electron micrographs showed exfoliated sheets decorated with nanoparticles, and transmission electron micrographs showed spherical nanoparticles about 10 nm in diameter well distributed on the individual graphene sheet. The electrocatalytic activity for the oxygen reduction reaction (ORR) was studied by cyclic voltammetry in an air-saturated electrolyte, finding that the best catalyst was the sample with a 1:2 Ni/Fe ratio, using a catalyst concentration of 15 mg·cm⁻² on graphite felt. The 1:2 Ni/Fe catalyst provided an oxygen reduction potential of 397 mV and a maximum oxygen reduction current of −0.13 mA; for comparison, an electrode prepared with GO/γ-Fe₂O₃ showed a maximum ORR of 369 mV and a maximum current of −0.03 mA. Microbial fuel cells with a vertical proton membrane were prepared with Ni-doped Fe₃O₄ and Fe₃O₄/graphene oxide and tested for 24 h; they reached a stable OCV of +400 mV and +300 mV OCV, and an efficiency of 508 mW·m⁻² and 139 mW·m⁻², respectively. The better performance of Ni-doped material was attributed to the combined presence of catalytic activity between γ-Fe₂O₃ and NiFe₂O₄, coupled with lower wettability, which led to better dispersion onto the electrode. Full article