Search Results (39)

Açaí, a berry emblematic of Amazonian biodiversity, is a major Brazilian product whose market value is largely concentrated in its pulp, leaving the residual biomass—particularly the fibrous seed—underexploited and typically discarded in landfills, with negative environmental and social consequences. To address this gap, this study employs a systematic technology roadmapping approach, integrating bibliometric analysis, patent landscaping, and expert consultations to consolidate fragmented data. This methodology enables the mapping of innovation trajectories across technology readiness levels, product categories, market segments, and key stakeholders. The roadmap identifies emerging trends and opportunity windows for valorizing açaí biomass via integrated biorefinery approaches, moving beyond traditional low-complexity uses such as thermal energy and seed-derived coffee substitutes. The highlighted products include pharmaceutical extracts, cosmetic ingredients, nanopapers, and cellulose nanocrystals, leveraging the biomass’s biochemical composition, notably antioxidants, mannose, and inulin. This methodological framework facilitates a dynamic analysis of technological maturation and market evolution, offering strategic insights to guide industrial investments and policy development. Findings indicate that biorefinery integration enhances resource efficiency and product diversification, situating açaí biomass valorization within broader bioeconomy strategies. The study demonstrates the efficacy of technology roadmapping in structuring prospective innovation pathways and in supporting the sustainable utilization of the Amazonian biomass. Full article

This research investigated the selected properties of nanocellulose films intended to serve as protective patches on fissured surfaces of wooden artefacts. The effects of their plasticisation with glycerol and functionalisation with selected silanes ((3-Glycidyloxypropyl)trimethoxysilane, and Methyltrimethoxysilane) were also determined. The obtained pure cellulose nanopapers (CNPs) had a homogeneous and compact structure but were very brittle, stiff, and wavy. Functionalisation with silanes made their structure more packed and reduced their equilibrium moisture content by 87–96%, depending on the type and concentration of the silane. Silane functionalisation also slightly improved nanopapers’ resistance to moulds. Plasticisation with glycerol provided CNPs with higher flexibility and resistance to fracture and made them flatter and smoother, reducing the wettability of their surfaces but increasing their hygroscopicity (EMC values increased 1.7–3.5 times for pure CNPs and 5–33 times for functionalised CNPs) and vulnerability to mould infestation. All prepared nanopapers can be easily glued to the wood surface and colour-matched using a nitro wood stain, oil paint or waterborne acrylic paint. The research showed that cellulose nanopapers modified with silanes and plasticised with glycerol seem to be a promising solution for protecting the cracked surface of wooden artefacts against further degradation due to external conditions. Full article

In this study, we present a novel method for fabricating semi-transparent electrodes by combining silver nanowires (AgNW) with titanium nitride (TiN) layers, resulting in conductive nanocomposite coatings with exceptional electromechanical properties. These nanocomposites were deposited on cellulose nanopaper (CNP) using a plasma-enhanced pulsed laser deposition (PE-PLD) technique at low temperatures (below 200 °C). Repetitive bending tests demonstrate that incorporating AgNW into TiN coatings significantly enhances the microstructure, increasing the electrode’s electromechanical robustness by up to four orders of magnitude compared to commercial PET/ITO substrates. Furthermore, the optical and electrical conductivities can be optimized by adjusting the AgNW network density and TiN synthesis temperature. Our results also indicate that the nanocomposite electrodes exhibit improved stability in air and superior adhesion compared to bare AgNW coatings. Full article

Multiwalled carbon nanotube (MWCNT) nanopaper (NP)-reinforced in-mold coating (IMC) nanocomposites were fabricated by dip soaking without organic solvent. The thermally activated IMC resin was selected to provide electromagnetic interference shielding protection for sheet molding compound (SMC) material as well as other plastic materials due to the proven good adhesion of IMC resin to the substrate. In this work, the technical feasibility of a continuous fabrication process was evaluated for a nanopaper/IMC (NP/IMC) composite. The curing behavior of the candidate IMC resin was studied for a better understanding of the fabrication of NP/IMC nanotape as a prepreg (with 10% polymerization), as well as the final curing once the nanotape was applied to the substrate. The required limiting maximum temperature to prevent curing during infiltration was established. This allows the fabrication of multilayer nanotape or coatings by stacking several layers of tape to improve the EMI shielding protection. To be specific, the average EMI shielding effectiveness for a one-layer composite was 21 dB, while it increased to 48 dB on average for a six-layer composite. Full article

In this study, we are reporting the fabrication of a nanocellulose (NFC) paper-based food indicator for chicken breast spoilage detection by both visual color change observation and smartphone image analysis. The indicator consists of a nanocellulose paper (nanopaper) substrate and a pH-responsive dye, bromocresol green (BCG), that adsorbs on the nanopaper. The nanopaper is prepared through vacuum filtration and high-pressure compression. The nanopaper exhibits good optical transparency and strong mechanical strength. The color change from yellow to blue in the nanopaper indicator corresponding to an increase in the solution pH and chicken breast meat storage data were observed and analyzed, respectively. Further, we were able to use color differences determined by the RGB values from smartphone images to analyze the results, which indicates a simple, sensitive, and readily deployable approach toward the development of future smartphone-based food spoilage tests. Full article

Artificial photosynthesis has rapidly developed as an actual field of research, mimicking natural photosynthesis processes in plants or bacteria to produce energy or high-value chemicals. The nanocelluloses are a family of biorenewable materials that can be engineered into nanostructures with favorable properties to serve as a host matrix for encapsulation of photoreactive moieties or cells. In this review, the production of different nanocellulose structures such as films, hydrogels, membranes, and foams together with their specific properties to function as photosynthetic devices are described. In particular, the nanocellulose’s water affinity, high surface area and porosity, mechanical stability in aqueous environment, and barrier properties can be tuned by appropriate processing. From a more fundamental viewpoint, the optical properties (transparency and haze) and interaction of light with nanofibrous structures can be further optimized to enhance light harvesting, e.g., by functionalization or appropriate surface texturing. After reviewing the basic principles of natural photosynthesis and photon interactions, it is described how they can be transferred into nanocellulose structures serving as a platform for immobilization of photoreactive moieties. Using photoreactive centers, the isolated reactive protein complexes can be applied in artificial bio-hybrid nanocellulose systems through self-assembly, or metal nanoparticles, metal-organic frameworks, and quantum dots can be integrated in nanocellulose composites. Alternatively, the immobilization of algae or cyanobacteria in nanopaper coatings or a porous nanocellulose matrix allows to design photosynthetic cell factories and advanced artificial leaves. The remaining challenges in upscaling and improving photosynthesis efficiency are finally addressed in order to establish a breakthrough in utilization of nanocellulose for artificial photosynthesis. Full article

Sustainable biomass-derived carbons have attracted research interest because of their ability to effectively absorb and convert solar light to thermal energy, a phenomenon known as solar thermal heating. Although their carbon-based molecular and nanoporous structures should be customized to achieve enhanced solar thermal heating performance, such customization has insufficiently progressed. In this study, we transformed a chitin nanofiber/water dispersion into paper, referred to as chitin nanopaper, with subwavelength nanoporous structures by spatially controlled drying, followed by temperature-controlled carbonization without any pretreatment to customize the carbon-based molecular structures. The optimal carbonization temperature for enhancing the solar absorption and solar thermal heating performance of the chitin nanopaper was determined to be 400 °C. Furthermore, we observed that the nitrogen component, which afforded nitrogen-doped carbon structures, and the high morphological stability of chitin nanofibers against carbonization, which maintained subwavelength nanoporous structures even after carbonization, contributed to the improved solar absorption of the carbonized chitin nanopaper. The carbonized chitin nanopaper exhibited a higher solar thermal heating performance than the carbonized cellulose nanopaper and commercial nanocarbon materials, thus demonstrating significant potential as an excellent solar thermal material. Full article

In the first part of the review article “General considerations” we give information about conventional flexible platforms and consider the advantages and disadvantages of paper when used in humidity sensors, both as a substrate and as a humidity-sensitive material. This consideration shows that paper, especially nanopaper, is a very promising material for the development of low-cost flexible humidity sensors suitable for a wide range of applications. Various humidity-sensitive materials suitable for use in paper-based sensors are analyzed and the humidity-sensitive characteristics of paper and other humidity-sensitive materials are compared. Various configurations of humidity sensors that can be developed on the basis of paper are considered, and a description of the mechanisms of their operation is given. Next, we discuss the manufacturing features of paper-based humidity sensors. The main attention is paid to the consideration of such problems as patterning and electrode formation. It is shown that printing technologies are the most suitable for mass production of paper-based flexible humidity sensors. At the same time, these technologies are effective both in the formation of a humidity-sensitive layer and in the manufacture of electrodes. Full article

Carboxycellulose nanofibers (CNFs) promise to be a sustainable and inexpensive alternative material for polymer electrolyte membranes compared to the expensive commercial Nafion membrane. However, its practical applications have been limited by its relatively low performance and reduced mechanical properties under typical operating conditions. In this study, carboxycellulose nanofibers were derived from wood pulp by TEMPO oxidation of the hydroxyl group present on the C6 position of the cellulose chain. Then, citric acid cross-linked CNF membranes were prepared by a solvent casting method to enhance performance. Results from FT-IR spectroscopy, ¹³C NMR spectroscopy, and XRD reveal a chemical cross-link between the citric acid and CNF, and the optimal fuel cell performance was obtained by cross-linking 70 mL of 0.20 wt % CNF suspension with 300 µL of 1.0 M citric acid solution. The membrane electrode assemblies (MEAs), operated in an oxygen atmosphere, exhibited the maximum power density of 27.7 mW cm⁻² and the maximum current density of 111.8 mA cm⁻² at 80 °C and 100% relative humidity (RH) for the citric acid cross-linked CNF membrane with 0.1 mg cm⁻² Pt loading on the anode and cathode, which is approximately 30 times and 22 times better, respectively, than the uncross-linked CNF film. A minimum activation energy of 0.27 eV is achieved with the best-performing citric acid cross-linked CNF membrane, and a proton conductivity of 9.4 mS cm⁻¹ is obtained at 80 °C. The surface morphology of carboxycellulose nanofibers and corresponding membranes were characterized by FIB/SEM, SEM/EDX, TEM, and AFM techniques. The effect of citric acid on the mechanical properties of the membrane was assessed by tensile strength DMA. Full article

Nanopapers fabricated from cellulose nanofibers (CNFs) are flexible for bending while they are rather stiff against stretching, which is a common feature shared by conventional paper-based materials in contrast with typical elastomers. Cellulose nanopapers have therefore been expected to be adopted in flexible device applications, but their lack of stretching flexibility can be a bottleneck for specific situations. The high stretching flexibility of nanopapers can effectively be realized by the implementation of Kirigami structures, but there has never been discussion on the mechanical resilience where stretching is not a single event. In this study, we experimentally revealed the mechanical resilience of nanopapers implemented with Kirigami structures for stretching flexibility by iterative tensile tests with large strains. Although the residual strains are found to increase with larger maximum strains and a larger number of stretching cycles, the high mechanical resilience was also confirmed, as expected for moderate maximum strains. Furthermore, we also showed that the round edges of cut patterns instead of bare sharp ones significantly improve the mechanical resilience for harsh stretching conditions. Thus, the design principle of relaxing the stress focusing is not only important in circumventing fractures but also in realizing mechanical resilience. Full article

We combine renewable and waste materials to produce hydrophobic membranes in the present work. Cellulose nanopaper prepared from paper waste was used as a structural component for the membrane. The pine wax was reclaimed from pine needle extraction waste and can be regarded as a byproduct. The dip-coating and spray-coating methods were comprehensively compared. In addition, the solubility of wax in different solvents is reported, and the concentration impact on coating quality is presented as the change in the contact angle value. The sensile drop method was used for wetting measurements. Spray-coating yielded the highest contact angle with an average of 114°, while dip-coating reached an average value of 107°. Scanning electron microscopy (SEM) was used for an in-depth comparison of surface morphology. It was observed that coating methods yield significantly different microstructures on the surface of cellulose fibers. The wax is characterized by nuclear magnetic resonance (NMR) spectroscopy and differential scanning calorimetry (DSC). Pine wax has a melting temperature of around 80 °C and excellent thermal stability in oxygen, with a degradation peak above 290 °C. Fourier transform infrared spectroscopy (FTIR) was used to identify characteristic groups of components and show the changes on coated nanopaper. Overall, the results of this work yield important insight into wax-coated cellulose nanopapers and a comparison of spray- and dip-coating methods. The prepared materials have a potential application as membranes and packaging materials. Full article

The route for the preparation of cellulose nanofiber dispersions from bacterial cellulose using ethylene glycol- or glycerol-based deep eutectic solvents (DES) is demonstrated. Choline chloride was used as a hydrogen bond acceptor and the effect of the combined influence of DES treatment and ultrasound on the thermal and mechanical properties of bacterial cellulose nanofibers (BC-NFs) is demonstrated. It was found that the maximal Young’s modulus (9.2 GPa) is achieved for samples prepared using a combination of ethylene glycol-based DES and ultrasound treatment. Samples prepared with glycerol-based DES combined with ultrasound exhibit the maximal strength (132 MPa). Results on the mechanical properties are discussed based on the structural investigations that were performed using FTIR, Raman, WAXD, SEM and AFM measurements, as well as the determination of the degree of polymerization and the density of BC-NF packing during drying with the formation of paper. We propose that the disordering of the BC-NF surface structure along with the preservation of high crystallinity bulk are the key factors leading to the improved mechanical and thermal characteristics of prepared BC-NF-based papers. Full article

Cellulose materials and products are frequently affected by environmental factors such as light, temperature, and humidity. Simulated UV irradiation, heat, and moisture exposure were comprehensively used to characterize changes in cellulose nanopaper (NP) tensile properties. For the preparation of NP, high-purity cellulose from old, unused filter paper waste was used. Lignin and xylan were used as sustainable green interface engineering modifiers for NP due to their structural compatibility, low price, nontoxic nature, and abundance as a by-product of biomass processing, as well as their ability to protect cellulose fibers from UV irradiation. Nanofibrillated cellulose (NFC) suspension was obtained by microfluidizing cellulose suspension, and NP was produced by casting films from water suspensions. The use of filler from 1 to 30 wt% significantly altered NP properties. All nanopapers were tested for their sensitivity to water humidity, which reduced mechanical properties from 10 to 40% depending on the saturation level. Xylan addition showed a significant increase in the specific elastic modulus and specific strength by 1.4- and 2.8-fold, respectively. Xylan-containing NPs had remarkable resistance to UV irradiation, retaining 50 to 90% of their initial properties. Lignin-modified NPs resulted in a decreased mechanical performance due to the particle structure of the filler and the agglomeration process, but it was compensated by good property retention and enhanced elongation. The UV oxidation process of the NP interface was studied with UV-Vis and FTIR spectroscopy, which showed that the degradation of lignin and xylan preserves a cellulose fiber structure. Scanning electron microscopy images revealed the structural formation of the interface and supplemented understanding of UV aging impact on the surface and penetration depth in the cross-section. The ability to overcome premature aging in environmental factors can significantly benefit the wide adaption of NP in food packaging and functional applications. Full article

This paper deals with the design, preparation, and characterization of conductive and flexible nanopapers based on graphite nanoplates (GNP) and polydimethylsiloxane (PDMS). Highly porous GNP nanopapers were first prepared by filtration from a GNP suspension in a solvent. Subsequently, PDMS impregnation was carried out to obtain a composite material. By varying the concentration of the polymer solution and the deposition time, PDMS/GNP nanopapers were produced with a wide range of PDMS contents, porosities, and densities. Thermal diffusivity of the composite films (both in-plane and cross-plane) were measured and correlated with the structure of the nanopapers. Selected formulations were investigated in detail for their physical, thermal, and mechanical properties, exhibiting high flexibility and resistance to more than 50 repeated bendings, stiffness of up to 1.3 MPa, and thermal conductivity of up to 25 W/m∙K. Based on the properties obtained, the materials presented in this paper may find applications in modern lightweight and flexible electronic devices. Full article

Nanocelluloses are promising bio-nano-materials for use as water treatment materials in environmental protection and remediation. Over the past decades, they have been integrated via novel nanoengineering approaches for water treatment processes. This review aims at giving an overview of nanocellulose requirements concerning emerging nanotechnologies of waster treatments and purification, i.e., adsorption, absorption, flocculation, photocatalytic degradation, disinfection, antifouling, ultrafiltration, nanofiltration, and reverse osmosis. Firstly, the nanocellulose synthesis methods (mechanical, physical, chemical, and biological), unique properties (sizes, geometries, and surface chemistry) were presented and their use for capturing and removal of wastewater pollutants was explained. Secondly, different chemical modification approaches surface functionalization (with functional groups, polymers, and nanoparticles) for enhancing the surface chemistry of the nanocellulose for enabling the effective removal of specific pollutants (suspended particles, microorganisms, hazardous metals ions, organic dyes, drugs, pesticides fertilizers, and oils) were highlighted. Thirdly, new fabrication approaches (solution casting, thermal treatment, electrospinning, 3D printing) that integrated nanocelluloses (spherical nanoparticles, nanowhiskers, nanofibers) to produce water treatment materials (individual composite nanoparticles, hydrogels, aerogels, sponges, membranes, and nanopapers) were covered. Finally, the major challenges and future perspectives concerning the applications of nanocellulose based materials in water treatment and purification were highlighted. Full article