Search Results (20)

Absorption spectra are widely used in laboratory practice to measure the content of a great variety of colloidal semiconductor nanocrystals. In the case of atomically thin nanoplatelets, only CdSe has been studied enough to allow such quantification, while CdTe nanoplatelets—a promising material for photodetection—are understudied in this regard. In this work, a powerful combination of total XRF spectroscopy, absorption spectroscopy and profilometry was employed for thin films to extract the absorption coefficient values. The morphology and surface composition of nanoplatelets were studied with TEM and IR spectroscopy. The molar absorption coefficient of oleate-terminated CdTe nanoplatelets at the first optical transition was measured at about 5 × 10⁴ L·mol⁻¹·cm⁻¹ (per mole of Te), which is among the highest values for AIIBVI nanomaterials. The exchange of stabilizer with hexadecanethiol induced an approximately 5-fold decrease in the volume fraction of semiconductor material in thin films and a 5-fold decrease in absorbance. The latter effect is linked to the formation of a quasi-type II heterojunction between CdTe cores and effectively half of a monolayer shell of CdS. The density effect is explained by the diminished capacity of nanoscrolls for close packing. The combination of XRF and profilometry is proposed as a technique for fast nanomorphology evaluation. Full article

This research investigated the feasibility of producing strontium-doped nanocrystalline hydroxyapatite (SrHAp) through an environmentally benign synthesis approach and evaluated the antimicrobial activity of the resulting material. The synthesized nanomaterial was subjected to comprehensive characterization. The antimicrobial efficacy of SrHAp was tested against Gram-positive and Gram-negative bacterial strains. X-ray diffraction (XRD) analysis in combination with Fourier-transform infrared (FT-IR) spectroscopy confirmed the successful formation of pure monocrystalline SrHAp. The scanning electron microscopy (SEM) examination revealed two predominant morphological structures: nanorods and prismatic configurations of the SrHAp. Transmission electron microscopy (TEM) demonstrated that the rod-like SrHAp nanocrystals aggregate into elongated grain structures with a size of about 25 nm × 10 nm. Inductively coupled plasma-optical emission spectroscopy (ICP-OES) analysis confirmed the presence and quantification of the concentrations of calcium, strontium, and phosphorus, while confirming the expected calcium–phosphorus ratio characteristic of hydroxyapatite. The study established that the positive surface charge of the material, with a point of zero charge near pH 10, is essential for its antimicrobial efficiency. These results suggest that SrHAp nanomaterials hold promise for biomedical applications, particularly as antimicrobial coatings for implants and scaffolds for bone tissue, where the prevention of infection is critical. Overall, despite its selective and material quantity-dependent antimicrobial efficacy, environmentally friendly synthesized SrHAp can be successfully applied as an effective controller of targeted microbial contamination, especially of Gram-positive bacterial species S. aureus, L. monocytogenes, S. Enteritidis, and A. baumanii. Full article

An electrochemical immunosensor for the quantification of prostate-specific antigens (PSAs) using silver nanocrystals (AgNCs) is reported. The silver nanocrystals were synthesized using a conventional citrate reduction protocol. The silver nanocrystals were characterized using scanning electron microscopy (SEM) and field effect scanning electron microscopy (FESEM), X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), Fourier-transform infrared spectroscopy (FTIR), UV-Vis spectroscopy, and small-angle X-ray scattering (SAXS). The proposed immunosensor was fabricated on a glassy carbon electrode (GCE), sequentially, by drop-coating AgNCs, the electro-deposition of EDC-NHS, the immobilization of anti-PSA antibody (Ab), and dropping of bovine serum albumin (BSA) to prevent non-specific binding sites. Each stage of the fabrication process was characterized by cyclic voltammetry (CV). Using square wave voltammetry (SWV), the proposed immunosensor displayed high sensitivity in detecting PSA over a concentration range of 1 to 10 ng/mL with a detection limit of 1.14 ng/mL and R² of 0.99%. The immunosensor was selective in the presence of interfering substances like glucose, urea, L-cysteine, and alpha-methylacyl-CoA racemase (AMACR) and it showed good stability and repeatability. These results compare favourably with some previously reported results on similar or related technologies for PSA detection. Full article

Fusarium head blight (FHB) and Fusarium crown rot (FCR) are managed by the application of imidazole fungicides, which will be strictly limited by 2030, as stated by the European Green Deal. Here, a novel and eco-sustainable nanostructured particle formulation (NPF) is presented by following the principles of the circular economy. Cellulose nanocrystals (CNC) and resistant starch were obtained from the bran of a high amylose (HA) bread wheat and employed as carrier and excipient, while chitosan and gallic acid were functionalized as antifungal and elicitor active principles. The NPF inhibited conidia germination and mycelium growth, and mechanically interacted with conidia. The NPF optimally reduced FHB and FCR symptoms in susceptible bread wheat genotypes while being biocompatible on plants. The expression level of 21 genes involved in the induction of innate immunity was investigated in Sumai3 (FHB resistant) Cadenza (susceptible) and Cadenza SBEIIa (a mutant characterized by high-amylose starch content) and most of them were up-regulated in Cadenza SBEIIa spikes treated with the NPF, indicating that this genotype may possess an interesting genomic background particularly responsive to elicitor-like molecules. Quantification of fungal biomass revealed that the NPF controlled FHB spread, while Cadenza SBEIIa was resistant to FCR fungal spread. The present research work highlights that the NPF is a powerful weapon for FHB sustainable management, while the genome of Cadenza SBEIIa should be investigated deeply as particularly responsive to elicitor-like molecules and resistant to FCR fungal spread. Full article

The development of Ce-based materials is directly dependent on the catalyst surface defects, which is caused by the calcination steps required to increase structural stability. At the same time, the evaluation of cerium’s redox properties under reaction conditions is of increasing relevant importance. The synthesis of Ce-UiO-66 and CeZr-UiO-66 and their subsequent calcination are presented here as a simple and inexpensive approach for achieving homogeneous and stable CeO₂ and CeZrO_x nanocrystals. The resulting materials constitute an ideal case study to thoroughly understand cerium redox properties. The Ce³⁺/Ce⁴⁺ redox properties are investigated by H₂-TPR experiments exploited by in situ FT-IR and Ce M₅-edge AP-NEXAFS spectroscopy. In the latter case, Ce³⁺ formation is quantified using the MCR-ALS protocol. FT-IR is then presented as a high potential/easily accessible technique for extracting valuable information about the cerium oxidation state under operating conditions. The dependence of the OH stretching vibration frequency on temperature and Ce reduction is described, providing a novel tool for qualitative monitoring of surface oxygen vacancy formation. Based on the reported results, the molecular absorption coefficient of the Ce³⁺ characteristic IR transition is tentatively evaluated, thus providing a basis for future Ce³⁺ quantification through FT-IR spectroscopy. Finally, the FT-IR limitations for Ce³⁺ quantification are discussed. Full article

Chitin and its derivate chitosan have versatile properties and have been used in various applications. One key parameter determining the functionality of chitin-based materials is the degree of acetylation (DA). For DA determination, NMR and FTIR spectroscopy are often considered to be the gold standard, but these techniques may not always be available and are rather time-consuming and costly. The first derivative UV method has been suggested, although accurate measurements can be challenging for materials with high degrees of acetylation, due to hydroxymethylfurfural (HMF) formation and other side reactions occurring. In this paper, we re-evaluated the first derivate UV method for chitin and chitosan powder, chitin nanocrystals, and deacetylated chitin nanocrystals. Our results showed that the first derivative UV method is capable of measuring DA with high accuracy (>0.9), leading to values comparable to those obtained by ¹H NMR, ¹³C NMR, and FTIR. Moreover, by-product formation could either be suppressed by selecting the proper experimental conditions, or be compensated. For chitin nanocrystals, DA calculation deviations up to 20% due to by-product formation can be avoided with the correction that we propose. We conclude that the first derivative UV method is an accessible method for DA quantification, provided that sample solubility is warranted. Full article

This work presents a multipurpose and multilayered stainless steel microneedle sensor for the in situ redox potential monitoring in food and drink samples, termed MN redox sensor. The MN redox sensor was fabricated by layer-by-layer (LbL) approach. The in-tube multilayer coating comprised carbon nanotubes (CNTs)/cellulose nanocrystals (CNCs) as the first layer, polyaniline (PANI) as the second layer, and the ferrocyanide redox couple as the third layer. Using cyclic voltammetry (CV) as a transduction method, the MN redox sensor showed facile electron transfer for probing both electrical capacitance and redox potential, useful for both analyte specific and bulk quantification of redox species in various food and drink samples. The bulk redox species were quantified based on the anodic/cathodic redox peak shifts (E_a/E_c) on the voltammograms resulting from the presence of redox-active species. The MN redox sensor was applied to detect selected redox species including ascorbic acid, H₂O₂, and putrescine, with capacitive limits of detection (LOD) of 49.9, 17.8, and 263 ng/mL for each species, respectively. For the bulk determination of redox species, the MN redox sensor displayed LOD of 5.27 × 10³, 55.4, and 25.8 ng/mL in ascorbic acid, H₂O₂, and putrescine equivalents, respectively. The sensor exhibited reproducibility of ~1.8% relative standard deviation (%RSD). The MN redox sensor was successfully employed for the detection of fish spoilage and antioxidant quantification in king mushroom and brewed coffee samples, thereby justifying its potential for food quality and food safety applications. Lastly, the portability, reusability, rapid sampling time, and capability of in situ analysis of food and drink samples makes it amenable for real-time sensing applications. Full article

A portable, molecularly imprinted polymer (MIP)-based microneedle (MN) sensor for the electrochemical detection of imidacloprid (IDP) has been demonstrated. The MN sensor was fabricated via layer-by-layer (LbL) in-tube coating using a carbon nanotube (CNT)/cellulose nanocrystal (CNC) composite, and an IDP-imprinted polyaniline layer co-polymerized with imidazole-functionalized CNCs (PANI-co-CNC-Im) as the biomimetic receptor film. The sensor, termed MIP@CNT/CNC MN, was analyzed using both cyclic voltammetry (CV) and differential pulse voltammetry (DPV) and showed excellent electrochemical performance for the detection of IDP. The CV detection range for IDP was 2.0–99 µM, with limits of detection (LOD) of 0.35 µM, while the DPV detection range was 0.20–92 µM with an LOD of 0.06 µM. Additionally, the MIP@CNT/CNC MN sensor showed excellent reusability and could be used up to nine times with a 1.4 % relative standard deviation (% RSD) between uses. Lastly, the MIP@CNT/CNC MN sensor successfully demonstrated the quantification of IDP in a honey sample. Full article

A wearable, textile-based molecularly imprinted polymer (MIP) electrochemical sensor for cortisol detection in human sweat has been demonstrated. The wearable cortisol sensor was fabricated via layer-by-layer assembly (LbL) on a flexible cotton textile substrate coated with a conductive nanoporous carbon nanotube/cellulose nanocrystal (CNT/CNC) composite suspension, conductive polyaniline (PANI), and a selective cortisol-imprinted poly(glycidylmethacrylate-co-ethylene glycol dimethacrylate) (poly(GMA-co-EGDMA)) decorated with gold nanoparticles (AuNPs), or plated with gold. The cortisol sensor rapidly (<2 min) responded to 9.8–49.5 ng/mL of cortisol, with an average relative standard deviation (%RSD) of 6.4% across the dynamic range, indicating excellent precision. The cortisol sensor yielded an excellent limit of detection (LOD) of 8.00 ng/mL, which is within the typical physiological levels in human sweat. A single cortisol sensor patch could be reused 15 times over a 30-day period with no loss in performance, attesting to excellent reusability. The cortisol sensor patch was successfully verified for use in quantification of cortisol levels in human sweat. Full article

The reference intensity ratio (RIR) method, using X-ray diffraction (XRD), is considered one most of the rapid and convenient approaches for phase quantification in multi-phase mixture, in which nanocrystals are commonly contained in a mixture and cause a broadening of the diffraction peak, while another broadening factor, instrumental broadening, does not attract enough attention in related quantitative analysis. Despite the specimen consisting of 50 wt.% TiO₂ nanomaterials (nano-TiO₂) and 50 wt.% microscale ZnO powder, the nano-TiO₂ quantitative result changes from 56.53% to 43.33% that occur as a variation of instrumental broadening are caused by divergence slit adjustment. This deviation could be accounted through a mathematical model that involves instrumental broadening. The research in this paper might provide a useful guide for developing an approach to measure accuracy quantification in unknown multi-phase mixtures Full article

Nanocelluloses are very attractive materials for creating structured films with unique optical properties using different preparation techniques. Evaporation-induced self-assembly of cellulose nanocrystals (CNC) aqueous suspensions produces iridescent films with selective circular Bragg reflection. Blade coating of sonicated CNC suspensions leads to birefringent CNC films. In this work, fabrication of both birefringent and chiral films from non-sonicated CNC suspensions using a shear-coating method is studied. Polarization optical microscopy and steady-state viscosity profiles show that non-sonicated CNC suspensions (concentration of 6.5 wt%) evolve with storage time from a gel-like shear-thinning fluid to a mixture of isotropic and chiral nematic liquid crystalline phases. Shear-coated films prepared from non-sonicated fresh CNC suspensions are birefringent, whereas films prepared from suspensions stored several weeks show reflection of left-handed polarized light. Quantification of linear and circular birefringence as well circular dichroism in the films is achieved by using a Mueller matrix formalism. Full article

Evaporation-induced-self-assembly is widely used to produce chiral cellulose nanocrystal (CNC) free-standing films reflecting left-handed polarized light. Research on supported chiral CNC films is rather scarce. The reflection and/or transmission of unpolarized light are the most common optical techniques used to characterize the selective reflection of CNC films whereas the use of techniques to quantify chiral properties is limited. Here, the fabrication of chiral CNC films supported on glass substrates by a shear-coating method, as well as a full characterization of their polarization properties, are reported. Optical chirality is evidenced in films, showing a brilliant blue structural color when viewed through a left-handed polarizer and darkness through a right-handed polarizer. Mueller-matrix data in the reflection and transmission modes are used to quantitatively characterize the structural origin of color in the films. The quantification of the linear and circular birefringence, as well as circular dichroism, is performed by analytical inversion of the Mueller matrix data in the transmission mode and regression analysis using Tellegen constitutive equations. The equivalence of the two methods to quantify the structural chirality in CNC films is demonstrated. The swelling of films in water and kinetics during drying is studied by reflection spectroscopy. Full article

The synthesis of (Cu,Ag)-Zn-Sn-S (CAZTS) and Ag-Zn-Sn-S (AZTS) nanocrystals (NCs) by means of “green” chemistry in aqueous solution and their detailed characterization by Raman spectroscopy and several complementary techniques are reported. Through a systematic variation of the nominal composition and quantification of the constituent elements in CAZTS and AZTS NCs by X-ray photoemission spectroscopy (XPS), we identified the vibrational Raman and IR fingerprints of both the main AZTS phase and secondary phases of Ag-Zn-S and Ag-Sn-S compounds. The formation of the secondary phases of Ag-S and Ag-Zn-S cannot be avoided entirely for this type of synthesis. The Ag-Zn-S phase, having its bandgap in near infrared range, is the reason for the non-monotonous dependence of the absorption edge of CAZTS NCs on the Ag content, with a trend to redshift even below the bandgaps of bulk AZTS and CZTS. The work function, electron affinity, and ionization potential of the AZTS NCs are derived using photoelectron spectroscopy measurements. Full article

Glyphosate detection and quantification is still a challenge. After an extensive review of the literature, we observed that Fourier transform infrared spectroscopy (FTIR) had practically not yet been used for detection or quantification. The interaction between zinc oxide (ZnO), silver oxide (Ag₂O), and Ag-doped ZnO nanocrystals (NCs), as well as that between nanocomposite (Ag-doped ZnO/AgO) and glyphosate was analyzed with FTIR to determine whether nanomaterials could be used as signal enhancers for glyphosates. The results were further supported with the use of atomic force microscopy (AFM) imaging. The glyphosate commercial solutions were intensified 10,000 times when incorporated the ZnO NCs. However, strong chemical interactions between Ag and glyphosate may suppress signaling, making FTIR identification difficult. In short, we have shown for the first time that ZnO NCs are exciting tools with the potential to be used as signal amplifiers of glyphosate, the use of which may be explored in terms of the detection of other molecules based on nanocrystal affinity. Full article

Glucose sensors are potentially useful tools for monitoring the glucose concentration in cell culture medium. Here, we present a new, low-cost, and reproducible sensor based on a cellulose-based material, 2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO) oxidized-cellulose nanocrystals (CNCs). This novel biocompatible and inert nanomaterial is employed as a polymeric matrix to immobilize and stabilize glucose oxidase in the fabrication of a reproducible, operationally stable, highly selective, cost-effective, screen-printed glucose sensor. The sensors have a linear range of 0.1–2 mM (R² = 0.999) and a sensitivity of 5.7 ± 0.3 µA cm⁻²∙mM⁻¹. The limit of detection is 0.004 mM, and the limit of quantification is 0.015 mM. The sensor maintains 92.3 % of the initial current response after 30 consecutive measurements in a 1 mM standard glucose solution, and has a shelf life of 1 month while maintaining high selectivity. We demonstrate the practical application of the sensor by monitoring the glucose consumption of a fibroblast cell culture over the course of several days. Full article