Search Results (82)

Structural color is a kind of natural color that widely exists in nature. The ordered microstructure of nano materials can absorb or reflect light of specific wavelength, thus showing colorful colors. Structural color is an ideal choice for color contact lens pattern pigment due to its good tinting degree, stability, and nontoxicity. This paper explores a method for synthesis of zinc oxide (ZnO) nanoparticles with a high refractive index and enhancement of the brightness of the structured colors by introducing carbon black nanoparticles. This method is convenient and successful to prepare ZnO ink, which can produce bright structural colors, and to produce color patterns through rubber pad printing. It is worth mentioning that ZnO nanoparticles can be self-assembled and arranged in contact lens ink without subsequent complicated processing. At the same time, the color only comes from ZnO and carbon black. While there is no other organic matter, the presence of nanoparticles plays a certain role in sterilization. Blue contact lenses prepared by this method have bright structural color, high oxygen permeability, and high hydrophilicity. At the same time, a cell viability test showed that the contact lenses prepared by this method had low adsorption capacity for lipids and proteins, reflecting the photonic crystal’s high biocompatibility. In summary, a trend for future research is to use high-refractive-index zinc oxide nanoparticles to produce structural colors rather than employing conventional contact lens pigments. Full article

Printed electronics employ established printing methods to create low-cost, mechanically flexible devices including batteries, supercapacitors, sensors, antennas and RFID tags on plastic, paper and textile substrates. This review focuses on the specific contribution of screen printing to that landscape, examining how ink viscosity, mesh selection and squeegee dynamics govern film uniformity, pattern resolution and ultimately device performance. Recent progress in advanced ink systems is surveyed, highlighting carbon allotropes (graphene, carbon nano-onions, carbon nanotubes, graphite), silver and copper nanostructures, MXene and functional oxides that collectively enhance mechanical robustness, electrical conductivity and radio-frequency behavior. Parallel improvements in substrate engineering such as polyimide, PET, TPU, cellulose and elastomers demonstrate the technique’s capacity to accommodate complex geometries for wearable, medical and industrial applications while supporting environmentally responsible material choices such as water-borne binders and bio-based solvents. By mapping two decades of developments across energy-storage layers and functional electronics, the article identifies the key process elements, recurring challenges and emerging sustainable practices that will guide future optimization of screen-printing materials and protocols for high-performance, customizable and eco-friendly flexible devices. Full article

Effective high-aspect-ratio molds that minimize vacuum processes are becoming increasingly important for producing metalenses and other devices. To fabricate a high-aspect-ratio structure, a metal film must be used as a mask for dry etching, typically achieved via vacuum deposition. To avoid this vacuum process, we devised a method to develop an etching mask in the air using silver ink. The manufacturing method involved filling the mold with silver ink, baking it, removing silver from the convex parts of the mold with a polyethylene terephthalate film, and placing silver from the concave parts of the mold on top of the ultraviolet (UV)-cured resin using ultraviolet-nanoimprint lithography. The transferred pattern had silver on the convex parts, which was used as a mask for the oxygen dry etching of the UV-curable resin. Consequently, high-aspect-ratio resin shapes were obtained from three types of nano- and micromolds. Additionally, a high-aspect-ratio resin with silver was used as a replica mold to form a silver pattern. This process is effective and allows high-aspect-ratio patterns to be obtained from master molds. Full article

Three-dimensional (3D) models with improved biomimicry are essential to reduce animal experimentation and drive innovation in tissue engineering. In this study, we investigate the use of alginate-based materials as polymeric inks for 3D bioprinting of osteogenic models using human bone marrow stem/stromal cells (hBMSCs). A composite bioink incorporating alginate, nano-hydroxyapatite (nHA), type I collagen (Col) and hBMSCs was developed and for extrusion-based printing. Rheological tests performed on crosslinked hydrogels confirm the formation of solid-like structures, consistently indicating a superior storage modulus in relation to the loss modulus. The swelling behavior analysis showed that the addition of Col and nHA into an alginate matrix can enhance the swelling rate of the resulting composite hydrogels, which maximizes cell proliferation within the structure. The LIVE/DEAD assay outcomes demonstrate that the inclusion of nHA and Col did not detrimentally affect the viability of hBMSCs over seven days post-printing. PrestoBlue^TM revealed a higher hBMSCs viability in the alginate-nHA-Col hydrogel compared to the remaining groups. Gene expression analysis revealed that alginate-nHA-col bioink favored a higher expression of osteogenic markers, including secreted phosphoprotein-1 (SPP1) and collagen type 1 alpha 2 chain (COL1A2) in hBMSCs after 14 days, indicating the pro-osteogenic differentiation potential of the hydrogel. This study demonstrates that the incorporation of nHA and Col into alginate enhances osteogenic potential and therefore provides a bioprinted model to systematically study osteogenesis and the early stages of tissue maturation in vitro. Full article

Ultraviolet (UV) ink is a primary type of ink used in additive manufacturing with 3D inkjet printing. However, ink aggregation presents a challenge in nano-inkjet printing, affecting the stability and quality of the printing fluid and potentially leading to the clogging of nanometer-sized nozzles. This paper utilizes a Dissipative Particle Dynamics (DPD) simulation to investigate the aggregation behavior of alumina in a blend of 1,6-Hexanediol diacrylate (HDDA) and Trimethylolpropane triacrylate (TMPTA). By analyzing the effects of solid content, polymer component ratios, and dispersant concentration on alumina aggregation, the optimal ink formulation was identified. Compared to traditional experimental methods, DPD simulations not only reduce experimental costs and time but also reveal particle aggregation mechanisms that are difficult to explore through experimental methods, providing a crucial theoretical basis for optimizing ink formulations. This study demonstrates that alumina ceramic ink achieves optimal performance with a solid content of 20%, an HDDA-to-TMPTA ratio of 4:1, and 9% oleic acid as a dispersant. Full article

With the rapid development of integrated circuits, glass substrates are frequently utilized for prototyping various functional electronic circuits due to their superior stability, transparency, and signal integrity. In this experiment, copper wire was printed on a glass substrate using inkjet printing, and the electronic circuit was sintered through laser irradiation with a 532 nm continuous green laser. The relationship between resistivity and microstructure was analyzed after laser sintering at different intensities, scanning speeds, and iterations. The experimental results indicate that the conductivity of the sintered lines initially increases and then decreases with an increase in laser power and scanning speed. At the same power level, multiple sintering runs at a lower scanning speed pose a risk of increased porosity leading to reduced conductivity. Conversely, when the scanning speed exceeds the optimal sintering speed, multiple sintering runs have minimal impact on porosity and conductivity without altering the power. Full article

The rapid progress of the modern world has resulted in new materials and products created at an accelerating pace. As such, nanoparticles have widespread applications and often find their way into the aquatic ecosystem. In the case of freshwater ecosystems, one of the commonly used bioindicators species used for pollution assessment is Daphnid magna. The Organization for Economic Co-operation and Development (OECD), and other organizations such as the European Chemicals Agency (ECHA) and Environmental Protection Agency (EPA), have set guidelines for acute toxicity testing in daphnids that are severely lacking in terms of information on the characteristics of the exposure vessel when studying the adverse effects of nanoparticles (NPs). Understanding the toxicity mechanisms of nanomaterials is imperative given the scarcity of information on their adverse effects. Furthermore, miniaturization of nanotoxicity assays can reduce the number of daphnids used, as well as the cost and nanomaterial waste, and provide results even at the individual animal level with enhanced reproducibility of testing. In this study, the impact of the exposure vessel on the observed physiological changes of daphnids was investigated for a silver nano ink. Exposures in eleven commercially available vessels; nine made of plastic and two made of glass were compared for 24 h. The effect of surface to volume ratio of the exposure vessel and the animal number or “crowding” during exposure was investigated in the context of miniaturizing biomarker assays as alternatives to traditional experimental setups in Daphnid magna. Toxicity curves showed differences depending on the vessel used, while a novel feeding rate assay and the activity of key enzymes were assessed as physiology endpoints. Full article

This study aims to investigate the feasibility of using paper made from eco-friendly recycled and non-woody plants in graphic technology, particularly in offset printing. Instead of changing the composition or modifying the surface properties of the paper, the focus was on enhancing the print quality by modifying the printing ink. By modifying the printing inks, the quality of the prints on recycled and non-woody paper can be optimized, which in turn reduces the need for paper made from primary fibers. This approach can expand the use of alternative materials in graphic technology and design. The objective was to optimize the print quality on these sustainable materials. Five types of uncoated paper were used, with high-quality uncoated offset paper based on virgin fibers serving as a reference. Laboratory tests of the basic and surface properties were carried out to measure the paper quality parameters that are important for offset printing. The influence of the paper composition on its optical and colorimetric properties was also investigated. The interaction between the selected papers and offset inks was examined through measurements of adhesion parameters and ink transfer, i.e., the paper’s ability to accept the ink. To enhance the applicability of the investigated papers as printing substrates in the graphic industry, SiO₂ and TiO₂ nanoparticles were added to the offset inks. The influence of the paper composition on the colorimetric properties of the prints was also investigated. The print uniformity, as an important quality characteristic, was determined by measuring the mottling index. The research findings indicate that incorporating SiO₂ and TiO₂ nanoparticles into offset inks can enhance the interaction between the paper and ink, leading to improved print quality. This study provides new perspectives on the possibilities of using recycled and non-woody plant paper in offset printing without significantly compromising the quality of the print. Full article

Nanogenerators possess the capability to harvest faint energy from the environment. Among them, thermoelectric (TE), triboelectric, piezoelectric (PE), and moisture-enabled nanogenerators represent promising approaches to micro–nano energy collection. These nanogenerators have seen considerable progress in material optimization and structural design. Printing technology has facilitated the large-scale manufacturing of nanogenerators. Although inks can be compatible with most traditional functional materials, this inevitably leads to a decrease in the electrical performance of the materials, necessitating control over the rheological properties of the inks. Furthermore, printing technology offers increased structural design flexibility. This review provides a comprehensive framework for ink-based nanogenerators, encompassing ink material optimization and device structural design, including improvements in ink performance, control of rheological properties, and efficient energy harvesting structures. Additionally, it highlights ink-based nanogenerators that incorporate textile technology and hybrid energy technologies, reviewing their latest advancements in energy collection and self-powered sensing. The discussion also addresses the main challenges faced and future directions for development. Full article

Bi₂S₃ has gained considerable attention as a semiconductor for its versatile functional properties, finding application across various fields, and liquid phase exfoliation (LPE) serves as a straightforward method to produce it in nano-form. Till now, the commonly used solvent for LPE has been N-Methyl-2-pyrrolidone, which is expensive, toxic and has a high boiling point. These limitations drive the search for more sustainable alternatives, with water being a promising option. Nonetheless, surfactants are necessary for LPE in water due to the hydrophobic nature of Bi₂S₃, and organic molecules with amphoteric characteristics are identified as suitable surfactants. However, systematic studies on the use of ionic surfactants in the LPE of Bi₂S₃ have remained scarce until now. In this work, we used sodium dodecyl sulfate (SDS), sodium dodecylbenzene sulfonate (SDBS) and sodium hexadecyl sulfonate (SHS) as representative species and we present a comprehensive investigation into their effects on the LPE of Bi₂S₃. Through characterizations of the resulting products, we find that all surfactants effectively exfoliate Bi₂S₃ into few-layer species. Notably, SDBS demonstrates superior stabilization of the 2D layers compared to the other surfactants, while SHS becomes the most promising surfactant for obtaining products with high yield. Moreover, the resulting nano-inks are used for fabricating films using spray-coating, reaching a fine tuning of band gap by controlling the number of cycles, and paving the way for the utilization of 2D Bi₂S₃ in optoelectronic devices. Full article

Natural and synthetic polymers are a versatile platform for developing biomaterials in the biomedical and environmental fields. Natural polymers are organic compounds that are found in nature. The most common natural polymers include polysaccharides, such as alginate, hyaluronic acid, and starch, proteins, e.g., collagen, silk, and fibrin, and bacterial polyesters. Natural polymers have already been applied in numerous sectors, such as carriers for drug delivery, tissue engineering, stem cell morphogenesis, wound healing, regenerative medicine, food packaging, etc. Various synthetic polymers, including poly(lactic acid), poly(acrylic acid), poly(vinyl alcohol), polyethylene glycol, etc., are biocompatible and biodegradable; therefore, they are studied and applied in controlled drug release systems, nano-carriers, tissue engineering, dispersion of bacterial biofilms, gene delivery systems, bio-ink in 3D-printing, textiles in medicine, agriculture, heavy metals removal, and food packaging. In the following review, recent advancements in polymer chemistry, which enable the imparting of specific biomedical functions of polymers, will be discussed in detail, including antiviral, anticancer, and antimicrobial activities. This work contains the authors’ experimental contributions to biomedical and environmental polymer applications. This review is a vast overview of natural and synthetic polymers used in biomedical and environmental fields, polymer synthesis, and isolation methods, critically assessessing their advantages, limitations, and prospects. Full article

This paper reports a high-performance humidity sensor made using a novel cellulose nanofiber (CNF)–silver nanoparticle (AgNP) sensing material. The interdigital electrode pattern was printed via reverse-offset printing using Ag nano-ink, and the sensing layer on the printed interdigitated electrode (IDE) was formed by depositing the CNF-AgNP composite via inkjet printing. The structure and morphology of the CNF-AgNP layer are characterized using ultraviolet–visible spectroscopy, an X-ray diffractometer, field emission scanning electron microscopy, energy-dispersive X-ray analysis, and transmission electron microscopy. The humidity-sensing performance of the prepared sensors is evaluated by measuring the impedance changes under the relative humidity variation between 10 and 90% relative humidity. The CNF-AgNP sensor exhibited very sensitive and fast humidity-sensing responses compared to the CNF sensor. The electrode distance effect and the response and recovery times are investigated. The enhanced humidity-sensing performance is reflected in the increased conductivity of the Ag nanoparticles and the adsorption of free water molecules associated with the porous characteristics of the CNF layer. The CNF-AgNP composite enables the development of highly sensitive, fast-responding, reproducible, flexible, and inexpensive humidity sensors. Full article

Labels are a crucial component of products, offering informational content and attractive visuals; therefore, the durability of the print is an important quality requirement. On the other hand, in accordance with eco-design, the recyclability of printed labels is vital. In our research, the focus was on the assessment of the durability, recyclability, and deinkability of printed label paper equipped with printed RFID tags. The determined color fastness of electrophotographic prints affected by various environmental factors showed good resistance to dry rubbing and, in most cases, light and moist–heat treatment, confirming the applicability of digital printing on self-adhesive biodegradable paper labels. In the second part of this study, recyclability was assessed, and a comparison between the deinkability of the offset and digital prints and two conductive functional inks was conducted. Good deinkability was observed for the printed RFID antennas on both the offset and electrographic prints, with only a small deterioration in optical properties, especially when nano-silver conductive ink was used. The study highlights the importance of the selection of materials and printing techniques when considering the environmental impact of printed electronics. The results showed that INGEDE 11 is a suitable deinking method for printed RFID antennas on offset and electrographic prints. Full article

The great increase in nanotechnology in the last 20 years has led to the alarming presence of nanomaterials in the environment as a new category of pollutants. Given the fact that legislation on nanomaterials is not concrete, the monitoring of their toxicity responses remains central. Focusing on tests in aquatic environments, daphnids are commonly employed as a bioindicator species for experiments with nanomaterials. However, until now, there has not been a unified and agreed approach to nanotoxicity testing, while research among different laboratories has been performed with significantly different setups, which may affect the reproducibility of the results. In this study, daphnids were exposed to silver nanoinks and the impact of surface to volume was assessed by comparing shallow vessels such as Petri dishes with deeper exposure vessels. Furthermore, in an attempt to assess whether the tests can be performed in smaller volumes, and thus in miniaturized versions, experiments compared larger and smaller volume setups. Finally, another parameter explored was the crowding of animals in exposure, and therefore their absolute number. Mortality was affected by both surface to volume and miniaturization, and significantly with crowding, supporting the implication of the number of animals in the tests. Further investigation with molecular and phenotypic endpoints confirmed these changes. Full article

This paper shows the design of an injector, using carbon nanotubes as inkjet material, implemented in a 3D printer. According to the available literature, few injectors are capable of depositing material. Due to the lack of information, the central part of this research is to develop a suitable device for ink injection that is capable of applying the Fused Deposition Modeling (FDM) method to print nanomaterial ink. The injector was designed using a CAD program based on an open-source desktop 3D printer, which allows it to be modified according to the needs of the injector. This prototype was manufactured in aluminum alloy 7075T6. Computational fluid dynamics (CFD) were carried out to analyze the behavior of the fluid when it passes through the injector, obtaining parameters such as pressure, velocity, and vorticity. An experimental matrix of the injector operation was carried out to achieve an adequate printing speed. The results show that the optimum speed was 250 ms, considering that a temperature of 100 °C is needed in the heated bed to dry the ink so that it does not undergo expansion. Full article