Search Results (818)

Ecotribology focuses on both saving energy resources and reducing environmental pollution. Considering environmental concerns, water-based nanolubricants have gained significant attention over conventional oil-based ones. Non-ecotoxic and highly environmentally friendly nanoadditives were chosen for nanolubricant synthesis, especially considering their use at elevated temperatures. In this study, hexagonal boron nitride nanosheets (hBNNSs) and titanium dioxide nanoparticles (TiO₂ NPs) were used to prepare water-based lubricants with glycerol and surfactant sodium dodecyl benzene sulfonate (SDBS) in water under ultrasonication. An Rtec ball-on-disk tribometer was used to investigate the tribological performance of the synthesised water-based lubricants containing different nano-hBN/TiO₂ concentrations, with dry and water conditions used as benchmarks. The results indicated that the water-based nanolubricant containing 0.5 wt% hBN and 0.5 wt% TiO₂ exhibited the best tribological performance at both ambient (25 °C) and elevated (500 °C) temperatures. This optimal concentration leads to a reduction in the coefficient of friction (COF) by 72.9% and 37.5%, wear of disk by 62.5% and 49%, and wear of ball by 74% and 69% at ambient and elevated temperatures, respectively, compared to that of distilled water. Lubrication mechanisms were attributed to the rolling, mending, tribofilm, solid layer formation, and synergistic effects of hBNNSs and TiO₂ NPs. Full article

Magnesium phosphate cement (MPC) exhibits brittleness when utilized as a repair material for bridge decks. To address this issue, this study employs nano-TiO₂ (NT) and a novel material (basalt fiber bar) as modifiers. A double-K fracture model is developed for the modified MPC to quantitatively evaluate the enhancement of fracture toughness induced by NT and basalt fiber bars. The cracking behavior and toughening mechanisms of the NT and basalt fiber bar reinforced MPC are investigated using extended finite element theory and composite material theory. Additionally, a formula is proposed to calculate the incremental fracture toughness of NT and basalt fiber bar reinforced MPC. The results indicated that NT and basalt fiber bar can effectively enhance the ultimate bending capacity of MPC. The improvement increases with the fiber volume fraction, and noticeable bending hardening occurs when the fiber content exceeds 2%. With the same fiber volume fraction, the peak load can be increased by up to 11.7% with the addition of NT. The crack initiation toughness of the NT group without basalt fiber bars is 58% higher than that of the CC group. The content and diameter of basalt fiber bar are critical parameters affecting the toughness of the NT and basalt fiber bar reinforced MPC. Full article

A simple and efficient dispersive micro solid-phase extraction (DMSPE) method using nano-TiO₂ as a sorbent was developed for the separation and preconcentration of (ultra) trace levels of lead in water samples prior to quantification by electrothermal atomic absorption spectrometry (ETAAS). Key experimental parameters affecting the DMSPE process, including pH, ionic strength, sorbent dosage, and preconcentration factor, were optimized. The optimized method demonstrated a preconcentration factor of 20, a relative standard deviation below 4.5%, and a detection limit of 0.11 µg/L. The procedure was validated using certified reference material (CRM TM-25.5) and applied to real water samples from a lake, a residential well, and industrial wastewater. Satisfactory recoveries (89–103%) confirmed the reliability of the method for the determination of low lead concentrations in complex matrices. Full article

The accumulation of nanoparticles (NPs) in the female body has raised global concerns regarding potential effects on the reproductive system. This study aimed to investigate the toxic effects of nano-titanium dioxide (nano-TiO₂) exposure on the ovaries and the underlying mechanisms. By establishing a nano-TiO₂ accumulation model in mice, our research systematically evaluated the effects of different concentrations of nano-TiO₂ exposure on the development and reproductive endocrine functions of mice. The results showed that nano-TiO₂ exposure significantly reduced the littering rate, sex hormone levels, and ovarian index of mice, and the effects were dose-dependent. Studies on the mechanisms involved revealed that nano-TiO₂ induces an excessive production of reactive oxygen species (ROS), leading to the potential collapse of the mitochondrial membrane and an increase in the apoptosis rate of granulosa cells, thereby triggering oxidative stress and inhibiting the expression of ovarian-specific genes and granulosa-cell function genes. This study reveals the “dual blow” mechanism of nano-TiO₂-mediated ovarian morphology and function through oxidative stress in granulosa cells, namely directly disrupting cellular homeostasis and interfering with the reproductive-related gene network, ultimately leading to decreased ovarian function. This provides experimental evidence for assessing the reproductive risks of nanomaterials in women. Full article

The superhydrophobic coatings for outdoor use need to be exposed to sunlight for a long time; therefore, their UV-aging resistances are crucial in practical applications. In this study, the primary product of titanium dioxide (P-TiO₂) was used as the raw material. Nano-silica (SiO₂) was coated onto the surface of P-TiO₂ by the acid precipitation method to prepare P-TiO₂-SiO₂ composite particles. Then, they were modified and sprayed simply to obtain a superhydrophobic P-TiO₂-SiO₂/HDTMS coating. The results indicated that amorphous nano-SiO₂ was coated on the P-TiO₂ surface, forming a micro–nano binary structure, which was the essential structure to form superhydrophobic coatings. Additionally, the UV-aging property of P-TiO₂ was significantly enhanced after being coated with SiO₂. After continuous UV irradiation for 30 days, the color difference (ΔE*) and yellowing index (Δb*) values of the coating prepared with P-TiO₂-SiO₂ increased from 0 to 0.75 and 0.23, respectively. In contrast, the ΔE* and Δb* of the coating prepared with P-TiO₂ increased from 0 to 1.68 and 0.74, respectively. It was clear that the yellowing degree of the P-TiO₂-SiO₂ coating was lower than that of P-TiO₂, and its UV-aging resistance was significantly improved. After modification with HDTMS, the P-TiO₂-SiO₂ coating formed a superhydrophobic P-TiO₂-SiO₂/HDTMS coating. The water contact angle (WCA) and water slide angle (WSA) on the surface of the coating were 154.9° and 1.3°, respectively. Furthermore, the coating demonstrated excellent UV-aging resistance. After continuous UV irradiation for 45 days, the WCA on the coating surface remained above 150°. Under the same conditions, the WCAs of the P-TiO₂/HDTMS coating decreased from more than 150° to 15.3°. This indicated that the retention of surface hydrophobicity of the P-TiO₂-SiO₂/HDTMS coating was longer than that of P-TiO₂/HDTMS, and the P-TiO₂-SiO₂/HDTMS coating’s UV-aging resistance was greater. The superhydrophobic P-TiO₂-SiO₂/HDTMS self-cleaning coating reported in this study exhibited outstanding UV-aging resistance, and it had the potential for long-term outdoor use. Full article

Due to its persistence and potential negative effects on ecosystems and human health, microplastic pollution in aquatic environments has become a major worldwide concern. Photocatalytic degradation is a sustainable manner to degrade microplastics to non-toxic by-products. In this review, comprehensive discussion focuses on the synergistic effects of various photocatalytic materials including TiO₂, ZnO, WO₃, graphene oxide, and metal–organic frameworks for producing heterojunctions and involving multidimensional nanostructures. Such mechanisms can include the generation of reactive oxygen species and polymer chain scission, which can lead to microplastic breakdown and mineralization. The advancements of material modifications in the (nano)structure of photocatalysts, doping, and heterojunction formation methods to promote UV and visible light-driven photocatalytic activity is discussed in this paper. Reactor designs, operational parameters, and scalability for practical applications are also reviewed. Photocatalytic systems have shown a lot of development but are hampered by shortcomings which include a lack of complete mineralization and production of intermediary secondary products; variability in performance due to the fluctuation in the intensity of solar light, limited UV light, and environmental conditions such as weather and the diurnal cycle. Future research involving multifunctional, environmentally benign photocatalytic techniques—e.g., doped composites or composite-based catalysts that involve adsorption, photocatalysis, and magnetic retrieval—are proposed to focus on the mechanism of utilizing light effectively and the environmental safety, which are necessary for successful operational and industrial-scale remediation. Full article

This study reports the impact of a silver nanoparticles/reduced graphene oxide@titanium dioxide nanocomposite (Ag/rGO@TiO₂) on the mechanical and biocompatibility properties of poly(styrene-co-methylmethacrylate)/poly methyl methacrylate (PS-PMMA/PMMA)-based bone cement. The chemical, structural, mechanical, and thermal characteristics of Ag/rGO@TiO₂ nanocomposite-reinforced PS-PMMA bone cement ((Ag/rGO@TiO₂)/(PS-PMMA)/PMMA) were evaluated using Fourier Transform Infrared spectroscopy (FT-IR), X-ray diffraction (XRD), nano-indentation, and electron microscopy. FT-IR, XRD, and transmission electron microscopy results confirmed the successful synthesis of the nanocomposite and the nanocomposite-incorporated bone cement. The elastic modulus (E) and hardness (H) of the ((Ag/rGO@TiO₂)/(PS-PMMA)/PMMA) bone cement were measured to be 5.09 GPa and 0.202 GPa, respectively, compared to the commercial counterparts, which exhibited E and H values of 1.7 GPa to 3.7 GPa and 0.174 GPa, respectively. Incorporating Ag/rGO@TiO₂ nanocomposites significantly enhanced the thermal properties of the bone cement. Additionally, in vitro studies demonstrated that the bone cement was non-toxic to the MG63 cell line. Full article

Water, acetone, and TiO₂/nano-silver water (NSW) nanofluids were investigated as working fluids in loop thermosyphon battery thermal management systems (LTBMS) under simulated electric vehicle (EV) conditions to evaluate scalability and robustness across inclinations (0° to 60°) and ambient temperatures (−10 °C to 20 °C). Experimental conditions were established with 60 °C as the reference temperature, corresponding to the onset of battery thermal runaway, to ensure relevance to critical thermal management scenarios. Results indicate that LTBMS A maintained battery cell temperatures at 50.4 °C with water and 31.6 °C with acetone under a 50 W heat load. In contrast, LTBMS B achieved cell temperatures of 41.8 °C with water and 42.8 °C with 0.01 vol% TiO₂ nanofluid, however, performance deteriorated at higher nanofluid concentrations due to increased viscosity and related thermophysical constraints. In heating mode, LTBMS A elevated cell temperatures by 16 °C at an ambient temperature of −10 °C using acetone, while LTBMS B attained 52–55 °C at a 100 W heat load with nanofluids. The lightweight LTBMS design demonstrated superior thermal performance compared to conventional air-cooling systems and performance comparable to liquid-cooling systems. Pure water proved to be the most effective working fluid, while nanofluids require further optimization to enhance their practical applicability in EV thermal management. Full article

Nano-titanium dioxide (nano-TiO₂) can alleviate oxidative damage in plants subjected to abiotic stress, interfere with related gene expression, and change metabolite content. Polylactic acid (PLA) microplastics can inhibit plant growth, induce oxidative stress in plant cells, and alter the biophysical properties of rhizosphere soil. In this study, untargeted metabolomics (LC-MS) and RNA-seq sequencing were performed on radish root cells exposed to nano-TiO₂ and PLA. The results showed that nano-TiO₂ alleviated the growth inhibition of radish roots induced by PLA. Nano-TiO₂ alleviated PLA-induced oxidative stress, and the activities of SOD and POD were decreased by 28.6% and 36.0%, respectively. A total of 1673 differentially expressed genes (DEGs, 844 upregulated genes, and 829 downregulated genes) were detected by transcriptome analysis. Metabolomics analysis showed that 5041 differential metabolites were involved; they mainly include terpenoids, fatty acids, alkaloids, shikimic acid, and phenylpropionic acid. Among them, phenylpropanoid biosynthesis as well as flavone and flavonol biosynthesis were the key metabolic pathways. This study demonstrates that nano-TiO₂ mitigates PLA phytotoxicity in radish via transcriptional and metabolic reprogramming of phenylpropanoid biosynthesis. These findings provide important references for enhancing crop resilience against pollutants and underscore the need for ecological risk assessment of co-existing novel pollutants in agriculture. Full article

MgO–C refractory materials were developed by incorporating different ratios of alumina/titania nano-additives which were synthesized chemically. Their physical and mechanical properties, oxidation resistance, slag wettability, bulk density, apparent porosity, cold crushing strength, oxidation index, and closed porosity were tested, evaluated, and compared using conventional techniques as well as X-ray micro-computed tomography (µCT). This investigation indicated a slight degradation of physical properties and mechanical strengthening which was stronger for samples with increased alumina content. Oxidation and corrosion extent were tested both with X-ray tomography and conventional methods. The first method allowed for the calculation of the oxidation index, the detection of closed porosity, and an improved analysis of the internal corrosion, avoiding the sectioning of the materials. This result confirms the supremacy of the first technique. On the contrary, although conventional methods such as the Archimedes procedure cannot detect close porosity, they provide more accurate measurements of the physical properties of refractories. This study shows that conventional methods exhibit superiority in investigations of the pore structures of refractories for pore sizes in the range 1–2 μm, while the use of the μCT system is limited for pore sizes equal to or larger than 20 μm. Full article

Reinforced concrete structures are prone to the development of microcracks during service. In this study, a composite-modified epoxy potting adhesive was formulated using nano-TiO₂, carboxyl-terminated butadiene nitrile liquid rubber (CTBN), and the reactive diluent D-669. The mechanical properties and effectiveness of this composite adhesive in repairing oblique cracks were systematically evaluated and compared with those of single-component-modified epoxy adhesives. Key material parameters influencing the performance of oblique crack repair were identified, and the underlying repair mechanisms were analyzed. Based on these findings, a theoretical formula for calculating the shear-bearing capacity of beams with repaired web reinforcement was proposed. Experimental results demonstrated that compared to single-component-modified epoxy resin, the optimally formulated composite adhesive improved the tensile strength, elongation at break, and bond strength by 4.07–21.16 MPa, 13.28–20.4%, and 1.05–3.79 MPa, respectively, while reducing the viscosity by 48–872 mPa·s. The viscosity of the adhesive was found to play a critical role in determining the repair effectiveness, with toughness enhancing the crack resistance and bond strength contributing to the structural stiffness recovery. The adhesive effectively penetrated the steel–concrete interface, forming a continuous bonding layer that improved energy dissipation and significantly enhanced the load-bearing capacity of the repaired beams. Full article

Background: Traditional sandblasted large-grit acid-etched (SLA) surface treatments frequently utilize alumina (Al₂O₃) blasting, which may leave residual particles embedded in implant surfaces, potentially compromising biocompatibility and osseointegration. This study investigates a contamination-free alternative: titanium dioxide particle (TiO₂) blasting followed by hydrochloric acid (HCl) etching, aimed at generating a cleaner, hierarchical micro–nano-textured surface. Methods: Grade IV titanium disks were treated either with TiO₂ sandblasting alone or with an additional HCl etching step. Surfaces were analyzed via atomic force microscopy (AFM), scanning electron microscopy (SEM), contact angle measurements, and profilometry. hFOB osteoblasts were cultured to assess adhesion, proliferation, metabolic activity, and morphology. Results: The combination treatment produced a more homogeneous micro–nano structure with significantly increased roughness and a cleaner surface chemistry. Osteoblast proliferation and metabolic activity were notably improved in the TiO₂ and HCl group. SEM imaging showed a more organized cytoskeletal structure and pronounced filopodia at 72 h. Conclusions: Titanium blasting combined with HCl etching yields a cost-effective, contamination-free surface modification with promising early-stage cellular responses. This approach represents a safer and effective alternative to conventional SLA treatment. Full article

Micro-sandblasting pretreatment was applied to AlTiSiN-coated WC–Co tools to enhance cutting performance in 316 L stainless steel milling. An L₉(3³) Taguchi orthogonal array varied passivation pressure (0.1, 0.2, and 0.3 MPa), gun traverse speed (60, 80, and 100 m/min), and tool rotation speed (20, 30, and 40 r/min). Coating thickness varied only from 0.93 to 1.19 μm, and surface roughness remained within 0.044–0.077 μm, confirming negligible thickness and roughness effects. Under optimized conditions, coating adhesion strength and nano-hardness both exhibited significant improvements. A weighted-scoring method balancing these two responses identified the optimal pretreatment parameters as 0.1 MPa, 80 m/min, and 20 r/min. Milling tests at 85 m/min—using flank wear VBₘₐₓ = 0.1 mm as the failure criterion—demonstrated a cutting distance increase from 4.25 m (untreated) to 12.75 m (pretreated), a 200% improvement. Wear progressed through three stages: rapid initial wear, extended steady wear due to Al₂O₃ protective-film formation and Si-induced oxygen-diffusion suppression, and accelerated wear. Micro-sandblasting further prolonged the steady-wear phase by removing residual cobalt binder, exposing WC grains, and offsetting tensile residual stresses. These findings establish a practical, cost-effective micro-sandblasting pretreatment strategy that significantly enhances coating adhesion, hardness, and tool life, providing actionable guidance for improving the durability and machining performance of coated carbide tools in difficult-to-cut applications. Full article

This study elucidates the photocatalytic NOx abatement efficacy of eco-efficient mortars incorporating construction waste-derived aggregates functionalized with nano-TiO₂. The research findings demonstrate a positive correlation between NOx abatement efficiency and nano-TiO₂ substitution ratio, with recycled glass sand (RG)-based panels exhibiting superior performance compared to standard sand and recycled clay brick sand (RCBS)-based counterparts. The employment of ultrasonic dispersion as a nano-TiO₂ incorporation method yields enhanced abatement efficiency relative to direct mixing, attributable to improved photocatalyst dispersion and surface area accessibility. The loading capacity of nano-TiO₂ on recycled aggregates is observed to be positively influenced by the concentration of nano-TiO₂ solution, with recycled clay brick sand demonstrating the highest loading capacity. RG-RCBS panels are shown to exhibit higher NOx abatement efficiency than standard sand (SS)-RCBS panels, with an optimal substitution ratio of 40% glass sand identified for maximizing abatement efficacy in RG-RCBS systems. A decline in NOx abatement efficiency is observed with increasing NOx flow rate and concentration, attributable to reduced pollutant residence time and excess pollutant load exceeding the panels’ processing capacity. Prolonged curing time also results in diminished abatement efficiency, due to microstructural alterations within the mortar matrix and the accumulation of photocatalytic reaction byproducts. Collectively, these findings underscore the potential of recycled aggregate-based mortars, in conjunction with nano-TiO₂, as a viable eco-efficient strategy for NOx abatement, highlighting the critical influence of material selection, photocatalyst loading, and operational parameters on system performance. Full article

The use of UV filters is a well-established strategy for preventing skin cancer and photoaging. Among inorganic filters, titanium dioxide (TiO₂) provides excellent protection against both UVA and UVB radiation. Moreover, the use of such inorganic filters at the nano-sized scale has increased their acceptability because it ensures the cosmetically desired transparency in sunscreens that consumers demand. However, concerns remain regarding the potential toxicity of TiO₂ nanoparticles, and discussion about their use in pharmaceuticals and cosmetics is still in progress. Their increased (bio)reactivity compared to bulk materials may lead to DNA damage. Furthermore, their capacity to cross dermal, respiratory, and gastrointestinal membranes remains a subject of debate. This study is therefore designed to assess and contrast the toxicological characteristics of a pair of commercially available titanium (IV) oxide sunscreens differing in particle size—microscale versus nanoscale. First, the morphology and hydrodynamic diameter of the TiO₂ nanoparticles were characterized. Then, potential interactions and/or interferences of these nanoparticles with the methods used to evaluate cytotoxic behavior were studied. Finally, the hemocompatibility, cytotoxicity, phototoxicity, and genotoxicity of both micro- and nano-sized TiO₂ were evaluated using human keratinocytes. Full article