Search Results (2,106)

This study introduces a synergistic drop-casting, sonication, and thermal treatment (DSTT) method for fabricating multi-walled carbon nanotube (MWCNT)-coated conductive cotton fabrics. The process produced uniform MWCNT networks with a minimum sheet resistance of 0.072 ± 0.004 kΩ/sq. at ~30 wt.% loading. Scanning electron microscopy confirmed an improved MWCNT network. Reproducibility was demonstrated for different fabric sizes, with resistance values remaining consistent within experimental errors. Stability tests showed only minor changes in sheet resistance after 16 weeks of ambient storage and periodic manual bending. Compared to conventional methods such as room-temperature drying, vacuum drying, and sonication alone, DSTT consistently performed better, yielding fabrics with lower resistance and more reliable conductivity. These results highlight DSTT as a reproducible and scalable method for producing conductive cotton fabrics suitable for smart textiles and wearable electronics. Full article

This study investigates the synergistic effects of hybrid fibers and functionalized multi-walled carbon nanotubes (MWCNTs) on the mechanical and microstructural properties of lithium slag–based geopolymers (FL-EGC). Unlike conventional studies that focus on single reinforcement strategies, this work combines nanoscale modification with macroscale fiber reinforcement to overcome the inherent brittleness of geopolymers. Results show that while hybrid fibers and MWCNTs reduce flowability, the incorporation of 2.5% PVA, 1.0% steel fibers, and 0.15% MWCNTs yielded the best balance of performance, improving ultimate tensile stress by 12.7%, strain by 69.2%, and specific fracture energy by 78.2%. Microstructural analysis confirmed that MWCNTs enhanced crack-bridging and matrix densification, while hybrid fibers improved strength and ductility. These findings demonstrate a novel reinforcement pathway for developing sustainable, high-performance geopolymers from industrial by-products, providing both theoretical insights and practical guidance for green construction materials. Full article

The main goal of the present article was to develop a methodology for the calculation of the flexural properties of a cement-based matrix with different multi-walled carbon nanotubes’ (CNTs) volume fraction as a reinforcement at early age. The homogenization tool of the ANSA^® software package was exploited for the modelling of the inclusion geometries in a cubic matrix and for mesh generation. A Representative Volume Element (RVE) was constructed with either random orientation tensor algorithm or periodic geometry algorithm tools and for different concentrations of the nano-reinforcement. Finite element modelling (FEM) of the pre-cracked specimens for flexural tests followed, and the numerical results were compared against the experimental ones. Different input parameters were considered, including the reinforcement Poisson’s ratio (ν_CNT) as well as the effective elastic modulus (E_CNT) to predict the flexural behaviour of the nano-reinforced matrices. It was found that both parameters play a pivotal role for the numerical simulation and the best simulation results were obtained for CNTs’ effective elastic modulus E_CNT = 470 GPa and Poisson’s ratio of ν_CNT = 0.10 values for the two (2) different investigated concentrations of carbon nanotubes (0.6 and 1.2%, respectively) in the cementitious matrix. Full article

To enhance the actuation performance of artificial muscles, a thermo-piezoelectric coupled model was developed based on the inverse piezoelectric effect of piezoelectric bimorphs. By altering the effective piezoelectric coefficient, elastic modulus, and effective thermal expansion coefficient of the thermo-piezoelectric bimorph model, the bending motion of artificial muscles was simulated. The effects of multi-walled carbon nanotube (MWCNT) and Genipin crosslinking on the bending force and output displacement of the artificial muscles were analyzed, illustrating how crosslinking affects the equivalent actuation response. The results showed that MWCNT and Genipin crosslinking significantly improved the actuation performance of the artificial muscles. Through numerical simulation, the optimal crosslinking ratio was determined to be 43.34% MWCNT and 0.1% Genipin, at which the best actuation performance was achieved. Compared to non-crosslinked techniques, the artificial muscles with crosslinked structures exhibited markedly enhanced actuation behavior. Full article

The development of multifunctional polymer composites capable of both heat conduction and latent heat storage is of great interest for advanced thermal management applications. In this work, thermoplastic polyurethane (TPU) nanocomposites containing microencapsulated paraffin-based phase change materials (PCMs) and multi-walled carbon nanotubes (MWCNTs) were systematically investigated. The microstructure, thermal stability, specific heat capacity, thermal diffusivity and conductivity of these composites were analyzed as a function of the PCM and MWCNTs content. SEM observations revealed the homogeneous dispersion of PCM microcapsules and the presence of localized MWCNT aggregates in PCM-rich domains. Thermal diffusivity measurements indicated a monotonic decrease with increasing temperature for all compositions, from 0.097 mm²·s⁻¹ at 5 °C to 0.091 mm²·s⁻¹ at 25 °C for neat TPU, and from 0.186 mm²·s⁻¹ to 0.173 mm²·s⁻¹ for TPU with 5 vol.% MWCNTs. Distinct non-linear behavior was observed around 25 °C, i.e., in correspondence to the paraffin melting, where the apparent diffusivity temporarily decreased due to latent heat absorption. The trend of the thermal conductivity (λ) was determined by the competing effects of PCM and MWCNTs: PCM addition reduced λ at 25 °C from 0.162 W·m⁻¹·K⁻¹ (neat TPU) to 0.128 W·m⁻¹·K⁻¹ at 30 vol.% PCM, whereas the incorporation of 5 vol.% of MWCNTs increased λ up to 0.309 W·m⁻¹·K⁻¹. In PCM-containing nanocomposites, MWCNT networks efficiently bridged the polymer–microcapsule interfaces, creating continuous conductive pathways that mitigated the insulating effect of the encapsulated paraffin and ensured stable heat transfer even across the solid–liquid transition. A one-dimensional transient heat-transfer model confirmed that increasing the matrix thermal conductivity accelerates the melting of the PCM, improving the dynamic thermal buffering capacity of these materials. Therefore, these results underlined the potential of TPU/MWCNT/PCM composites as versatile materials for applications requiring both rapid heat dissipation and effective thermal management. Full article

Materials with nonlinear conductivity are promising for electric field grading in various electrical and electronic devices because of their self-adaptability. In this study, we reported a nonlinear mechanism in fluorinated multi-wall carbon nanotube (F-MWCNT) clusters based on partial discharge in their porous structure. Excellent nonlinear conductivity featuring a low threshold electric field of around 2 kV/mm and a wide range of switching fields was observed after loading an ultra-low F-MWCNT loading ratio of 0.5 wt% into the UV-cured resin. Both experimental and theoretical analyses were performed to explain the underlying nonlinear mechanism. The improved electric field mitigation effect of the composite with F-MWCNT compared with the conventional inorganic fillers like SiC was validated by a flashover test in compressed SF₆ gas. Simulations were also conducted to explain the flashover threshold improvement considering the generation of seed electrons for ionization, which was in agreement with the experimental results. Full article

This study investigates the influence of silane coupling agents and multi-walled carbon nanotubes (MWCNTs) on the mechanical, durability, and thermal performance of CFRP rebars manufactured using a pilot-scale pultrusion process. The incorporation of additives extended epoxy working time without causing adverse viscosity effects during processing. Silane-modified CFRP rebars exhibited the highest mechanical performance, achieving a tensile strength of approximately 2649 MPa, an elastic modulus of 156 GPa, and improved bond strength with concrete, which is attributed to enhanced fiber–matrix interfacial adhesion. MWCNT-modified rebars showed slightly lower tensile strength but demonstrated superior thermal resistance, retaining the highest proportion of mechanical properties after exposure to 250 °C due to matrix reinforcement and crack-bridging effects. No significant degradation was observed under simulated marine exposure, while gradual reductions (up to ~7%) occurred in alkaline environments, with silane-modified rebars showing the greatest durability. These findings provide mechanistic insights and practical guidelines for optimizing epoxy formulations to enhance the structural and long-term performance of CFRP rebars. Full article

The development of membranes and patches for controlled drug release to enhance therapeutic efficacy is a promising approach to addressing the challenge posed by poor adherence to pharmacological therapies for chronic diseases. In this study, we designed an electrospun polycaprolactone (PCL) nanofibrous membrane reinforced with different concentrations (0.04%, 0.05%, 0.075%, and 0.2%) of functionalized multi-walled carbon nanotubes (f-MWCNTs) intended for biomedical applications, such as transdermal devices. We characterized the resulting composites using scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), atomic force microscopy (AFM), and dynamic mechanical analysis (DMA) to evaluate their morphology, chemical composition, and mechanical properties. We also measured their cytotoxicity upon contact with peripheral blood mononuclear cells. The nanofibers had diameters below 100 nm and inclusions of microspheres, which were attributed to the electrospinning expansion phenomenon. Spectroscopic and mechanical analyses confirmed molecular interactions between the PCL matrix and the f-MWCNTs. Finally, biological tests demonstrated that both the dispersion of f-MWCNTs and the nanofiber sizing render the membranes biocompatible, supporting their potential use as drug-delivery systems. Full article

The rapid advancement of humanoid robotics has spurred researchers’ interest in flexible sensors for wide linear range detection. In response, we report a capacitive flexible pressure sensor based on a multi-walled carbon nanotubes/titanium dioxide/polydimethylsiloxane (MWCNTs/TiO₂/PDMS) composite. A micro-hemispherical structure array formed on the composite surface via a templating method reduces the initial capacitance value. Modified carbon nanotubes (F-MWCNTs) were prepared using 2 wt%, 5 wt% and 10 wt% γ-aminopropyltriethoxysilane (APTES), significantly enhancing dispersion and interfacial bonding strength. The synergistic effect of microstructures and MWCNTs surface functionalization further enhances sensing performance. The F-MWCNTs/TiO₂/PDMS pressure sensor modified with 2 wt% APTES exhibits outstanding sensing capabilities: it demonstrates dual-stage sensitivity across a broad linear range of 0–95 kPa (0–13 kPa segment: 1.89 ± 0.49 kPa⁻¹; 13–95 kPa segment: 7.08 ± 0.63 kPa⁻¹), with a response time of 200 milliseconds, maintaining stability over 2500 cyclic loadings. In practical application exploration, this sensor has demonstrated strong adaptability, confirming its significant potential in micro-pressure detection, wearable electronics, and array sensing applications. Full article

Transparent conductive materials (TCMs) are essential for optoelectrical devices ranging from smart windows and defogging films to soft sensors, display technologies, and flexible electronics. Materials, such as indium tin oxide (ITO) and silver nanowires (AgNWs), are commonly used and offer high optical transmittance and electrical conductivity, but suffer from brittleness, oxidation susceptibility, and require high-cost materials, greatly limiting their use. Carbon nanotube (CNT) networks provide a promising alternative, featuring mechanical compliance, chemical robustness, and scalable processing. This study reports an aqueous ink formulation composed of ultra-long mix-walled carbon nanotubes (UL-CNTs), compatible with the flow coating process, yielding uniform transparent conductive films (TCFs) on polyethylene terephthalate (PET), glass, and polycarbonate (PC). The resulting films exhibit tunable transmittance (85%–88% for single layers; ~57% for three layers at 550 nm) and sheet resistance of 7.5 kΩ/□ to 1.5 kΩ/□ accordingly. These TCFs maintain stable sheet resistance for over 5000 bending cycles and show excellent mechanical durability with negligible effects on heating performance. Post-deposition treatments, including nitric acid vapor doping or flash photonic heating (FPH), further reduce sheet resistance by up to 80% (7.5 kΩ/□ to 1.2 kΩ/□). X-ray photoelectron spectroscopy (XPS) results in reduced surface oxygen content after FPH. The photonic-treated heaters attain ~100 °C within 20 s at 100 V. This scalable, water-based process provides a pathway toward low-cost, flexible, and stretchable devices in a variety of fields, including printed electronics, optoelectronics, and thermal actuators. Full article

Silicon is considered one of the most promising anode materials for lithium-ion batteries because of its high theoretical capacity and low lithiation potential. However, its practical application is limited by significant volume expansion, unstable solid–electrolyte interphase formation, and poor intrinsic conductivity. This review summarizes recent advances in hybrid strategies using multi-walled carbon nanotubes (MWCNTs), single-walled carbon nanotubes (SWCNTs), graphene, carbon nanofibers (CNFs), and pitch-derived carbons. We compare their respective benefits and drawbacks regarding conductivity, structural resilience, and scalability, while also addressing critical challenges such as dispersion, defect control, and processing costs. The discussion emphasizes the importance of hierarchical, multifunctional architectures that combine different forms of carbon to achieve synergistic performance. Finally, we outline future directions in interfacial engineering, defect and doping optimization, and electrode design under high-loading conditions. We believe that this review can offer perspectives on developing durable, energy-dense, and commercially viable silicon anodes for next-generation lithium-ion batteries. Full article

Background: Soft actuation relies on materials that are lightweight, flexible, and responsive to external stimuli. In biomedical applications, miniaturization and biocompatibility are key requirements for developing smart devices. Thermoplastic polyurethane (TPU) is particularly attractive due to its elasticity, processability, and biocompatibility; however, an improvement in its shape-recovery performance would significantly enhance its suitability for actuation systems. This study aims to develop TPU-based shape memory polymer (SMP) composites with improved functional behavior for biomedical applications. Methods: TPU was modified with aluminum nanoparticles (AlNPs) and multi-walled carbon nanotubes (MWCNTs), incorporated individually (1 wt.% and 3 wt.%) and in hybrid combinations (MWCNT:AlNP ratios of 2:1, 5:1, and 10:1). Samples were produced by compression molding and characterized through thermal, mechanical, electrical, and shape-recovery tests, supported by morphological analysis. Results: AlNPs moderately improved thermal conductivity, while MWCNTs significantly enhanced electrical conductivity and doubled the recovery force compared with neat TPU. Hybrid composites showed intermediate properties, with the 5:1 MWCNT:AlNP ratio offering the best balance between recovery force and activation speed. Conclusions: The synergistic combination of MWCNTs and AlNPs effectively enhances TPU’s multifunctional behavior, demonstrating strong potential for soft actuation in biomedical devices. Full article

A water-soluble hydroxypropyl cellulose (HPC) polymer matrix has been filled with different weight percentages (wt.%) of multiwalled carbon nanotubes (MWCNTs), fullerenes C₆₀, fullerenols C₆₀(OH)_24, and their combinations. We study the potential of the 0D nanoparticles for improving electrical properties of the conductive MWCNT network in a biocompatible matrix. Physicochemical effects of fillers content, both individually and in combinations (MWCNTs/C₆₀ and MWCNTs/C₆₀(OH)₂₄), for these composite systems, have been investigated. The performed SAXS analysis shows improved nanofiller dispersion for films with two fillers. The electrical percolation threshold (P_c) in MWCNTs composites occurs at ≈1.0 wt.%. A synergistic effect for binary filler composites on the electrical conductivity has been evaluated by keeping a constant amount of 0.5 wt.% MWCNTs (σ ≈ 3 × 10⁻⁹ S·m⁻¹) and increasing the amount of C₆₀ or C₆₀(OH)₂₄. A large increase in the electrical conductivity is obtained for the bifiller composites with 0.5 wt.% MWCNTs and 1.5 wt.% of C₆₀(OH)₂₄, reaching σ ≈ 0.008 S·m⁻¹. Further, the sensing properties of 4.0/1.0 MWCNT/C₆₀ nanocomposites were demonstrated by measuring both piezoresistive (PR) and thermoresistive (TR) responses. The combination of semiconductive fullerene/fullerenols combined with MWCNTs allows obtaining more homogeneous composites in comparison to single MWCNTs composites and also gives possibilities for tuning the electrical conductivity of the system. Overall, it is demonstrated that the use of bifillers with a water soluble biopolymeric matrix allows the development of eco-friendly high-performance electroactive materials for sustainable digitalization. Full article

This study investigates the synergistic influence of multi-walled carbon nanotubes (MWC-NTs), nanosilica powder (NSP), and polypropylene fiber waste (PFW) on the mechanical performance of mortar incorporating demolished concrete waste aggregates (DCWA). The replacement of natural aggregates with DCWA typically results in strength reductions and weak interfacial transition zones; therefore, the combined use of nanomaterials and microfibers is proposed as a mitigation strategy. A Taguchi Design of Experiments (DOE) approach was employed to optimize mix parameters, including MWCNT dosage, NSP content, PFW volume fraction, and DCWA replacement level. Mortar mixtures were prepared with MWCNTs (0–0.1% by binder weight), NSP (0–2% by binder weight), PFW (0–0.3% by volume), and DCWA (0–20% replacement of fine sand). Mechanical performance was assessed through compressive and flexural strength tests. A combined statistical approach using the Pareto chart and ANOVA identified the most influential parameters and their respective contributions to the response variable. The innovative aspect of this research lies in the synergistic integration of MWCNTs, NSP, demolished concrete waste, and polypropylene fiber waste within the mortar matrix, with the incorporation of nanomaterials specifically intended to compensate for the strength reduction typically induced by the use of demolition concrete waste aggregates. Although a potential nano-scale synergy between MWCNTs and NSP was initially considered, the experimental results indicated that the most relevant synergistic effects occurred among broader mix parameters rather than specifically between the two nanomaterials. Even so, when assessed individually, both nanomaterials contributed to improving the mechanical characteristics of the mortar—particularly nanosilica, which demonstrated a more pronounced effect—yet these individual enhancements did not translate into a distinct synergistic interaction between MWCNTs and NSP. The Taguchi DOE proved to be an efficient tool for multiple factor analysis, enabling reliable identification of the most influential parameters with a minimum number of tests. Its application facilitated the development of mortar mixtures that effectively integrate demolition waste while achieving enhanced mechanical performance through nano- and micro-scale reinforcement. Full article

The increasing exposure to non-ionizing electromagnetic (EM) radiation driven by urbanization and digitalization has encouraged the development of building materials with EM shielding properties. This study investigates the potential of enhancing the electromagnetic shielding properties of cement mortars by incorporating multi-walled carbon nanotubes (MWCNT) in various dosages (1%, 3%, 6%, 9% and 10% by binder mass). The microstructural and mechanical effects of MWCNT addition, as well as their efficiency in reducing EM transmission in the frequency range of 1.5–10 GHz (covering LTE, 5G, WiFi, and radar systems), were analyzed. S₂₁ measurements were performed using a modified coaxial transmission line method with a vector network analyzer. Results show that increasing the MWCNT content enhances EM shielding effectiveness but simultaneously affects the mortar’s microstructure and mechanical properties. Higher MWCNT levels achieved the best EM shielding, with an improvement of up to 27.66 dB compared to ordinary mortar in the navigation radar frequency range. These findings confirm the potential of MWCNT-modified mortars for protecting buildings and sensitive infrastructure—such a hospitals, communication hubs, data centers and military facilities—from EM radiation. Full article