Search Results (32)

To investigate the explosive characteristics of solid–liquid mixed fuels containing different types of metal powders—including hydrogen-storage metal powders—and volatile liquid fuels, explosion experiments and corresponding numerical simulations were conducted under unconstrained space conditions. The studied system consisted of Et₂O/Al/B/MgH₂ mixed fuels with varying composition ratios. Research has shown that the dispersion effect of solid–liquid mixed fuel containing metal dust under strong shock waves is higher than that of pure liquid fuel. And the explosion overpressure and temperature of solid–liquid mixed fuel are higher than that of pure liquid fuel. Under the same solid–liquid ratio, the explosive overpressure of Et₂O/Al/B/MgH₂ mixed fuel was the highest, which was 110.8% higher than that of pure liquid fuel at the 5 m position. For solid–liquid mixed fuels containing different metal powders, due to the high reaction threshold of boron powder, a high-activity MgH₂ reaction is required to drive the reaction. Therefore, the explosive strength of the mixed fuel systems follows the order Et₂O/Al/B/MgH₂ > Et₂O/Al/MgH₂ > Et₂O/Al > Et₂O/Al/B. Meanwhile, simulation models for pure liquid and solid–liquid fuel explosions were established. The discrepancy between the simulated results and the experimental data was within 10%, demonstrating that the proposed model provides an effective and reliable approach for predicting the explosive power and hazardous range of fuel–air explosions. Full article

To solve the problem of low energy release efficiency of fluoropolymer-based reactive materials, four PTFE (Polytetrafluoroethylene) -based reactive structural materials with different contents were prepared by adding traditional energetic materials (RDX, 1,3,5-Trinitrohexahydro-1,3,5-triazine) and alloy metals (aluminum magnesium, aluminum magnesium zinc). In addition, in order to reduce the high cost of the existing high-speed impact energy release testing device, the formulation optimization of PTFE-based aluminum alloy reactive material was efficiently carried out using a small-scale drop hammer impact test in this paper. The self-designed impact energy release testing device was established for the overpressure measurement of PTFE-based aluminum alloy reactive materials. The impact response processes of PTFE-based aluminum alloy reactive material were recorded with high-speed photography. The energy release characteristics were quantified using overpressure measurements. Based on the chemical reaction properties and microstructural characterization of the PTFE-based reactive materials, the ignition mechanism of aluminum alloy reactive materials was analyzed under drop hammer impact load. The results show that the quantitative characterization of the overpressure changes of reactive materials in a quasi-enclosed space before and after reaction can reflect their energy release efficiency under low-velocity impact by using the drop hammer impact energy release testing device. The order of impact response overpressure values for four PTFE-based reactive materials has been conducted. The aluminum alloy reactive material containing RDX explosive has the highest overpressure value and the highest energy release efficiency in terms of drop hammer impact response. Based on the ignition mechanism and energy release characteristics of these four PTFE-based reactive materials, it was found that the addition of alloy metal powder can reduce impact sensitivity, but when activated, it can effectively enhance the damage effect. Full article

During the homogenization process of lithium battery slurry, the slurry shearing process causes the surface of the homogenization equipment to wear and generate metal containing debris, which poses a risk of inducing battery self-discharge and even explosion. Therefore, inhibiting wear of homogenizing equipment is imperative, and systematic investigation into the wear behavior and underlying mechanisms of SUS304 stainless steel during homogenization is urgently required. In this study, lithium iron phosphate (LFP) and lithium nickel cobalt manganese oxide (NCM) cathode slurries were used as research objects. Changes in surface parameters, microstructure, and elemental composition of the wear region on SUS304 stainless steel under different working conditions were characterized. The results indicate that in the SUS304-lithium-ion battery slurry system, the potential wear mechanism of SUS304 gradually evolves with changes in load and rotational speed, following the order: adhesive wear (low speed, low load) → abrasive wear (medium speed, high load) → fatigue wear (high speed). Under high-load and high-rotational-speed conditions, oxidative corrosion wear on the ball–disc contact surface is particularly pronounced. Additionally, wear of SUS304 is more severe in the LFP slurry system compared to the NCM system. Macroscopic experiments also revealed that the speed effect is a core factor influencing the wear of SUS304, and the increase in its wear rate is more than twice that caused by the load effect. This study helps to clarify the wear behavior and wear mechanism evolution of homogenization equipment during the lithium battery homogenization process, providing data support and optimization direction for subsequent material screening and surface strengthening treatment of homogenization equipment components. Full article

Several decades after the development of FEM in computer-based form, which is a milestone in the evaluation of mechanical systems, the method has been adopted to analyze the biomechanical response of human skeletal structures. This innovative technique has generated new questions, but also new results, and, at the same time, competitive environments with explosive development, in the recent period. This research is focused on analyzing, using FEM, the extreme thermal variations produced at the level of two oro-facial systems (one control and one subjected to orthodontic therapy using a fixed metallic orthodontic appliance). The objective of the study was to determine the temperature evolution in different dental structures subjected to extreme temperatures given by variations between very cold and very hot foods. Each system was exposed to a succession of extreme thermal regimes (70…−18…70… °C and −18…70…−18… °C). In order to conduct this research, we used the case of a 14-year-old female patient. Following an orthodontic evaluation, we discovered that the patient had dento-alveolar disharmony with crowding. The straight-wire method of applying a fixed metallic orthodontic appliance was chosen. As complementary examinations, the patient was subjected to a bimaxillary CBCT. Using a series of programs (InVesalius, Geomagic, SolidWorks, and AnsysWorkbench), a three-dimensional model was obtained. This model contained jaws and teeth. Also, brackets, tubes, and orthodontic wires can be incorporated into the model. Following the simulations carried out in this study, it was found that thermal variations from the dental pulp are more severe for the oro-facial system with a fixed metallic orthodontic appliance (regardless of the type of thermal stimulus used). Thus, even today, with all the facilities available in the dental materials industry, metallic orthodontic devices present significant thermal conductivity, generating harmful effects on the dental structures. The reading of the results was performed on the virtual model, more precisely, on the internal dental structures (enamel, dentin, and pulp). A statistical study was not performed because it was considered that, in other patients, the results would be similar. Full article

High-entropy oxides are a new type of material that consists of five or more principal elements in an equimolar or nearly equimolar ratio. They have many excellent properties and are rapidly becoming a hotspot for the development of new high-performance materials. In this study, electrical explosion is used for the first time to synthesize high-entropy oxide nanopowders with different crystal structures. (FeCoNiCrCu)O is the rock salt structure, (FeCoNiCrTi)O is the spinel structure, and (CoNiTiCuZn)O contains the two phases. According to the TEM and EDS results, the distribution of the five metal elements in the electrical explosion products is comparatively homogeneous, and the particle size of the products is concentrated in 20–40 nm. Elements such as Ti are prone to the formation of spinel structure, and the element Cu is prone to the formation of rock salt structure. The study shows that the electrical explosion of wires is a new method for the synthesis of high-entropy oxide nanopowders. Full article

Nitroaromatic-explosives (NEs) not only threaten global security but are also recognized as a highly toxic pollutant. Metal–organic framework Zn-M_s (Zn-M₁, Zn-M₂) were synthesized in this study via the coordination-driven self-assembly of Zn ions and a carbazole-based ligand L containing an aldehyde group. They inherited the excellent fluorescence performance of ligand L and could work as a fluorescent sensor for detecting picric acid (PA) at low concentrations. Zn-M_s showed an emission at 450 nm and exhibited a higher fluorescence quenching efficiency toward PA than other related NEs. The results suggest that the fluorescent response might be attributed to the inner filter effect (IFE); Förster resonance energy transfer (FRET); and possibly, photo-induced electron transfer (PET). In addition, the critical role of the aldehyde group as a recognition site was corroborated using a post-modification strategy. Full article

The substitution of aluminum powder with highly reactive ultrafine aluminum-based metal fuels has a significant impact on the energy release of aluminum-containing energetic materials because of their excellent energy density and combustion performances. A series of ultrafine spherical Al-Mg alloy fuels with different contents of magnesium were prepared by close-coupled gas atomization technology. The properties of Al-Mg alloy powders of 13~15 μm were tested by SEM, TG-DSC, and laser ignition experiments. Results show that alloying with magnesium can significantly enhance thermal oxidation and combustion performance, leading to more oxidation weight gains and higher combustion heat release. HMX-based castable explosives with the same content of Al and the novel Al-Mg alloy were made and tested. Results show that the detonation performances of HMX/Al-Mg alloy/HTPB are better than HMX/Al/HTPB. Compared to the HMX/Al/HTPB explosive, the detonation heat of HMX/ Al-Mg alloy/HTPB was increased by 200 kJ/kg, the energy release efficiency was enhanced from 80.55% to 83.19%, the detonation velocity was increased by 114 m/s, and the shock wave overpressure at 5 m was increased by 83%. This research provides a new type of composite metal fuel for improving the combustion performance of Al powder. Full article

Metal-containing compounds form a large and rapidly expanding group of high-energy materials. Many compounds in this class attract the attention of non-professionals, who may attempt the illegal production of explosives. Several of these substances have been commercially available and pose significant danger if used by terrorists or for criminal purposes. Others are experimental compounds, kinds of curiosities, often created by pyrotechnics enthusiasts, which can present serious risks to both the creators and their immediate surroundings. The internet hosts a vast amount of information, including recipes and discussions on forums, private websites, social media, and more. This paper aims to review the variety of metal-containing explosives and discuss their appeal and potential accessibility to unauthorized individuals. Full article

In this work, energetic coordination compounds (ECCs) of transition metals (Fe, Ni, Cu, Zn) containing aliphatic amines as ligands were synthesized: ethylenediamine; 1,3-diaminopropane; tris(2-aminoethyl)amine; tris(3-aminopropyl)amine. The compounds were investigated in terms of ignition/explosion temperature, friction and impact sensitivity. For selected compounds, structural characterisation was presented (IR-ATR spectroscopy, Raman spectroscopy) and their morphology was determined (SEM, powder XRD). They were also investigated by differential scanning calorimetry (DSC). In order to assess the potential application of selected ECCs in detonators, underwater explosion tests were carried out, determining energetic performance. The results achieved for detonators containing ECCs were compared with those for reference detonators (containing pentaerythritol tetranitrate, PETN), indicating their potential use as a “green” alternative to nitric acid esters. Full article

(1) Background: The frequency and intensity of war-like activities (war, military training, and shooting ranges) worldwide cause soil pollution by metals, metalloids, explosives, radionuclides, and herbicides. Despite this environmentally worrying scenario, soil decontamination in former war zones almost always involves incineration. Nevertheless, this practice is expensive, and its efficiency is suitable only for organic pollutants. Therefore, treating soils polluted by wars requires efficient and economically viable alternatives. In this sense, this manuscript reviews the status and knowledge gaps of mycoremediation. (2) Methods: The literature review consisted of searches on ScienceDirect and Web of Science for articles (1980 to 2023) on the mycoremediation of soils containing pollutants derived from war-like activities. (3) Results: This review highlighted that mycoremediation has many successful applications for removing all pollutants of war-like activities. However, the mycoremediation of soils in former war zones and those impacted by military training and shooting ranges is still very incipient, with most applications emphasizing explosives. (4) Conclusion: The mycoremediation of soils from conflict zones is an entirely open field of research, and the main challenge is to optimize experimental conditions on a field scale. Full article

Conventional methods for producing porous metals involve the use of chemicals such as thickeners and foaming agents under high temperatures and pressures. However, these methods are costly and pose a risk of dust explosion. Thus, the objective of this research is to achieve the cost-effective and safe production of porous metals by introducing microbubbles generated by ultrasonic oscillation into the molten metal. One end of an ultrasonic horn was inserted into three different molten metals—white metal, Pb-free solder, and zinc—and microbubbles were generated at the horn end by the strong ultrasonic oscillation in the molten metals. The microbubbles that contained molten metal changed phase to porous metal through solidification, and the diameter, porosity, and stress–strain curve of the generated porous metals were measured. The results indicate that the porosity of white metal, Pb-free solder, and zinc foams reached 54%, 76%, and 48%, respectively, and these porous metals had many micropores less than 1 mm in diameter. It was also observed that the higher the melting point, the larger the pore diameter and the lower the porosity. Furthermore, in the case of white metal, a plateau region of large deformation at constant stress was observed in the stress–strain curve. Full article

Precious metals such as palladium (Pd) have many applications, ranging from automotive catalysts to fine chemistry. Platinum group metals are, thus, in massive demand for industrial applications, even though they are relatively rare and belong to the list of critical materials for many countries. The result is an explosion of their price. The recovery of Pd from spent catalysts and, more generally, the development of a circular economy process around Pd, becomes essential for both economic and environmental reasons. To this aim, we propose a sustainable process based on the use of supercritical CO₂ (i.e., a green solvent) operated in mild conditions of pressure and temperature (p = 25 MPa, T = 313 K). Note that the range of CO₂ pressures commonly used for extraction is going from 15 to 100 MPa, while temperatures typically vary from 308 to 423 K. A pressure of 25 MPa and a temperature of 313 K can, therefore, be viewed as mild conditions. CO₂-soluble copolymers bearing complexing groups, such as pyridine, triphenylphosphine, or acetylacetate, were added to the supercritical fluid to extract the Pd from the catalyst. Two supported catalysts were tested: a pristine aluminosilicate-supported catalyst (Cat D) and a spent alumina supported-catalyst (Cat A). An extraction conversion of up to more than 70% was achieved in the presence of the pyridine-containing copolymer. The recovery of the Pd from the polymer was possible after extraction, and the technological and economical assessment of the process was considered. Full article

Igneous rocks from the Russian Far East contain Cu-Ag-Au microspherules with distinct exterior and interior structures, compositions and assemblages of Cu-rich micro-inclusions. Natural microspherules are compared in this study with technogenic Cu-Ag-Au microspherules, which are experimentally produced and extracted from gold scrap jewelry. The following set of diagnostic criteria are considered to distinguish natural from technogenic microspherules on a genetic basis as follows: (1) compacted-related features versus cellular appearance of the exterior; (2) lack of exsolution- or crystallization-related features in natural and domain-type internal structure in technogenic microspherules; (3) absence of spherical copper-oxide inclusions along with meniscus-type textural boundaries in technogenic mcirospherules; (4) pure copper-oxide composition of inclusions versus the common presence of Fe, Ni, Zn, Cu and Na in natural microspherules. The diagnostic characteristics of natural Cu-Ag-Au microspherules suggest extremely fast cooling rates during their formation, which is possible during violent explosive volcanic eruptions or injection of partially molten, pulverized metal alloys into shallow intra-crustal cavities and fault-related tectonic gashes. Full article

Hydrogen is an efficient source of clean and environmentally friendly energy. However, because it is explosive at concentrations higher than 4%, safety issues are a great concern. As its applications are extended, the need for the production of reliable monitoring systems is urgent. In this work, mixed copper–titanium oxide ((CuTi)Ox) thin films with various copper concentrations (0–100 at.%), deposited by magnetron sputtering and annealed at 473 K, were investigated as a prospective hydrogen gas sensing material. Scanning electron microscopy was applied to determine the morphology of the thin films. Their structure and chemical composition were investigated by X-ray diffraction and X-ray photoelectron spectroscopy, respectively. The prepared films were nanocrystalline mixtures of metallic copper, cuprous oxide, and titanium anatase in the bulk, whereas at the surface only cupric oxide was found. In comparison to the literature, the (CuTi)Ox thin films already showed a sensor response to hydrogen at a relatively low operating temperature of 473 K without using any extra catalyst. The best sensor response and sensitivity to hydrogen gas were found in the mixed copper–titanium oxides containing similar atomic concentrations of both metals, i.e., 41/59 and 56/44 of Cu/Ti. Most probably, this effect is related to their similar morphology and to the simultaneous presence of Cu and Cu₂O crystals in these mixed oxide films. In particular, the studies of surface oxidation state revealed that it was the same for all annealed films and consisted only of CuO. However, in view of their crystalline structure, they consisted of Cu and Cu₂O nanocrystals in the thin film volume. Full article

A novel approach to electric explosion of intertwined wires to obtain homogeneous powder mixtures intended for preparing feedstock for extrusion 3D printing has been applied. The powder were composed of spherical micron- and nano-sized W/Cu particles in-situ alloyed by Zn and Ni during electric explosion of intertwined dissimilar metal wires is offered. The mean particle size measured by micron-sized particles was not more than 20 μm. The average number size of these particles was 3 μm and it was dependent on the energy input. The powders contained phases such as α-W, β-W/W₃O as well as FCC α-Cu(Zn) and α-Cu(Ni) solid solutions with the crystalline lattice parameters 3.629 and 3.61 A, respectively. Full article