Search Results (58)

Pigment implantation (semi-permanent make-up, microblading and cosmetic tattooing) introduces complex pigment mixtures into the dermis, resulting in direct exposure of keratinocytes, fibroblasts and resident immune cells to metals, organic dyes and nanoparticles. Within Somatology and Somatic therapy practice, an allied health discipline concerned with evidence-based care of the skin and body, Somatic Therapists operate at the interface of dermal intervention, molecular exposure and occupational health, underscoring the relevance of mechanistic toxicology for risk-informed professional practice. This PRISMA-guided systematic review synthesises molecular toxicology and omics-based evidence, emphasising oxidative stress generation, inflammatory signalling via NF-κB/MAPK pathways, apoptosis and genotoxicity, T-cell-mediated type IV hypersensitivity reactions associated with modern red azo pigments, and dermal-to-lymphatic transport of particulate matter. Transcriptomic and metabolomic studies consistently demonstrate pigment-specific inflammatory responses and wound-healing gene signatures, supporting mechanism-driven biocompatibility profiling. Regulatory frameworks, including EU REACH Annex XVII Entry 75 and recent FDA guidance on microbial contamination, have strengthened compliance requirements; however, surveillance continues to identify mislabelling, restricted pigments and microbial contamination in some inks. For Somatology and Somatic therapy practice, these findings highlight the importance of evidence-based pigment selection, traceable sourcing, aseptic technique, ventilation, personal protective equipment and informed consent addressing pigment migration and delayed adverse reactions. The integration of molecular outcomes with omics technologies and regulatory oversight provides a next-generation risk assessment framework to advance safe cosmetic practice and public health. Full article

Printed biosensors have attracted increasing attention as platforms for rapid, low-cost, and portable diagnostics because they can be fabricated on flexible or rigid substrates using scalable printing techniques. Their performance is strongly influenced by both the printing process and the materials employed, since factors such as ink rheology, particle dispersion, interfacial behavior, and post-processing conditions directly affect device architecture, sensing performance, and manufacturing reliability. This review summarizes recent advances in printed biosensors from the combined perspectives of printing technologies and functional materials. Commonly employed printing techniques, including inkjet, screen, aerosol jet, and roll-to-roll gravure printing, are discussed with emphasis on their processing characteristics and material requirements. The review also examines key material platforms used in printed biosensors, including carbon-based nanomaterials, metal oxides, metal nanoparticles, conductive polymers, dielectric materials, and hybrid composites, highlighting their roles in electrical conductivity, catalytic activity, biomolecule immobilization, mechanical flexibility, and overall analytical performance. Finally, current challenges and emerging research directions are outlined with respect to ink stability, post-processing strategies, sensor reliability, manufacturability, and practical translation. Overall, this review emphasizes that the development of high-performance printed biosensors depends on the synergistic integration of rational material design with optimized printing strategies. Full article

Printed electronics have emerged as a versatile manufacturing platform for next-generation biosensors, enabling on-demand and low-cost fabrication of functional devices on flexible, stretchable, and unconventional substrates. One major challenge in this field lies in the sintering of printed features, as conventional high-temperature processing is incompatible with polymeric substrates and thermally sensitive biological components. Low-temperature sintering inks, typically processed below 200 °C or even at room temperature, have become a critical enabling technology for bio-integrated electronics. This review provides an overview of the current state-of-the-art and key challenges associated with low-temperature sintering inks for printed bioelectronics. We discuss inks based on metal nanoparticles, metal–organic decomposition precursors, metal oxides, chalcogenides, and hybrid material systems. The emphasis is on how ink chemistry, ligand selection, and precursor structure govern rheology, stability, and sintering behavior. In addition, key low-temperature sintering and curing strategies, including thermal, photonic, laser, plasma, microwave, and chemical sintering, are compared in terms of energy delivery, densification mechanisms, and substrate compatibility. Finally, we outline emerging directions towards low temperature and room-temperature sintering inks, and sustainable biobased ink formulations, and discuss their applications for wearable, implantable, and soft biosensing platforms. Full article

This paper presents a comprehensive investigation into the synthesis, morphological characteristics, electrical conductivity, dielectric behavior, and electrocatalytic activity of perovskite-structured iron manganite (FeMnO₃), with a specific focus on its performance in the hydrogen evolution reaction (HER). FeMnO₃(FMO) nanoparticles (NPs) were synthesized using a sol–gel-type Pechini method and characterized by X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FT-IR), and field-emission scanning electron microscopy combined with energy-dispersive X-ray spectroscopy (FESEM-EDS). XRD analysis confirmed the formation of a crystalline structure with cubic symmetry assigned to the Ia-3 space group, with an average crystallite size of 52.47 nm. FESEM images revealed a relatively uniform morphology with an average particle diameter of 55.84 nm. The redox and oxidation states of Fe and Mn can be studied by temperature-programmed oxidation (TPO-O₂) in order to understand oxygen uptake and metal oxidation processes occurring within the FMO lattice. The dielectric constant, dielectric loss, electric modulus and electrical conductivity were calculated as a function of frequency and temperature using a Novocontrol Alpha-A broadband dielectric spectrometer (Novocontrol system) coupled with the LCR-800 precision meter. The dielectric data reveal that the FMO has semiconducting behavior with dominant charge- or ionic-relaxation processes. The electrocatalytic activity toward the HER was evaluated using linear sweep voltammetry (LSV), with the working electrode modified by an FMO catalyst ink. The material exhibited significant catalytic activity within the HER potential range, and an increase in the number of cycles led to stabilized current and enhanced hydrogen evolution. These results highlight the stability of FeMnO₃ for hydrogen generation. Full article

Squid ink has recently garnered considerable attention as a natural melanin source for the development of biocompatible nanomaterials. Although numerous studies have explored the biological and therapeutic applications of squid ink, the fabrication and modification strategies for squid ink-derived nanoparticles (SINPs) have yet to be comprehensively reviewed. This paper provides an integrated overview of current extraction, purification, and functionalization strategies for SINPs, with a particular focus on how functionalization approaches modulate their physicochemical characteristics and biological behaviors. The review begins by outlining the natural mechanisms of melanin formation and summarizing common extraction methods—including centrifugation, ultrasonication, and dialysis. Subsequently, various surface modification and hybridization techniques—including polymer coating, incorporation of metallic elements (e.g., Se and Fe), and loading of photosensitizers—are compared in terms of their contributions to functional enhancement. Finally, the challenges of reproducibility, batch-to-batch variability, and scalable manufacturing are discussed, outlining future directions for the development of squid ink-derived nanomaterials into standardized biomedical platforms. Full article

Residual-free eutectic Au80Sn20 soldering is still the dominant assembly technology for optoelectronic devices such as high-power lasers, LEDs, and photodiodes. Due to the high cost of gold, alternatives are desirable. This paper investigates the thermal performance of copper-based sintering for optoelectronic submodules on first and second level to obtain thermally efficient thin bondlines. Sintered interconnects obtained by a new particle-free copper ink, based on complexed copper salt, are compared with copper flake and silver nanoparticle sintered interconnects and benchmarked against AuSn solder interconnects. The copper ink is dispensed and predried at 130 °C to facilitate in situ generation of Cu nanoparticles by thermal decomposition of the metal salt before sintering. Submounts are then sintered at 275 °C for 15 min under nitrogen with 30 MPa pressure, forming uniform 2–5 µm copper layers achieving shear strengths above 31 MPa. Unpackaged LEDs are bonded on first level using the copper ink but applying only 10 MPa to avoid damaging the semiconductor dies. Thermal performance is evaluated via transient thermal analysis. Results show that copper ink interfaces approach the performance of thin AuSn joints and match silver interconnects at second level. However, at first level, AuSn and sintered interconnects of commercial silver and copper pastes remained superior due to the relative inhomogeneous thickness of the thin Cu copper layer after predrying, requiring higher bonding pressure to equalize surface inhomogeneities. Full article

This article outlines the method of creating electrodes for electrochemical sensors using hybrid nanostructures composed of graphene and conducting polymers with insertion of gold nanoparticles. The technology employed for graphene dispersion and support stabilization was based on the chemical vapor deposition technique followed by electrochemical delamination. The method used to obtain hybrid nanostructures from graphene and conductive polymers was drop-casting, utilizing solutions of P3HT, PANI-EB, and F8T2. Additionally, the insertion of gold nanoparticles utilized an innovative dip-coating technique, with the graphene-conducting polymer frameworks submerged in a HAuCl₄/2-propanol solution and subsequently subjected to controlled heating. The integration of gold nanoparticles differs notably, with P3HT showing the least adhesion of gold nanoparticles, while PANI-EB exhibits the highest. An inkjet printer was employed to create electrodes with metallization accomplished through the use of commercial silver ink. Notable variations in roughness (grain size) result in unique behaviors of these structures, and therefore, any potential differences in the sensitivity of the generated sensing structures can be more thoroughly understood through this spatial arrangement. The electrochemical experiments utilized a diluted sulfuric acid solution at three different scan rates. The oxidation and reduction potentials of the structures seem fairly alike. Nevertheless, a notable difference is seen in the anodic and cathodic current densities, which appear to be largely influenced by the active surface of gold nanoparticles linked to the polymeric grains. The graphene–PANI-EB structure with Au nanoparticles showed the highest responsiveness and will be further evaluated for biomedical applications. Full article

Our research outlines a method for creating chemosensors utilizing hybrid nanostructures derived from TiO₂ ceramic nanotubes alongside conducting polymers, with embedded gold nanoparticles. The method used to create hybrid nanostructures from ceramic nanotubes and conducting polymers was drop-casting. AFM analysis highlighted an increased roughness, particularly for PANI-EB, exhibiting a significantly larger grain size exceeding 3.5 μm, with an increased inclusion of gold and uniform arrangement on the surface. The Rku parameter values being around three suggested that the layers primarily exhibited peaks rather than depressions, showing a Gaussian distribution. A chemiresistor was created by using an ink-jet printer and a multilayer metallization was achieved with commercial silver ink for printed electronics. Based on the experimental calibration curve, which exhibits adequate linearity over a wider range of H₂S concentrations in air up to 1 ppm, the detection limit was established at 0.1 ppm, a threshold appropriate for recognizing oral diseases. The sensor is a simple, affordable, and durable device designed for individual use, offering significant benefits for patients by enabling improved tracking of the syndrome’s advancement or treatment success. Full article

Tattoo inks contain varying amounts of metal nanoparticles (NPs) < 100 nm that, due to their unique physicochemical properties, may have specific biological uptake and cause skin or systemic toxicities. The toxic effects of certified reference standards of metal NPs and samples of commercially available tattoo inks were investigated using an in vitro system and a novel human ex vivo model. In vitro toxicity was evaluated using vitality assays on human skin cells (HaCaT cell line, primary fibroblasts, and keratinocytes). No toxicity was observed for Al₂O₃, Cr₂O₃, Fe₂O₃, and TiO₂ NPs, whereas CuO NPs showed dose-dependent toxicity on HaCaT and primary fibroblasts. Fibroblasts and keratinocytes were also sensitive to high concentrations of ZnO NPs. Reference standards and ink samples were then injected ex vivo into human skin explants using tattoo needles. Histological analysis showed pigment distribution deep in the dermis and close to dermal vessels, suggesting possible systemic diffusion. The presence of an inflammatory infiltrate was also observed. Immunohistochemical analysis showed increased apoptosis and expression of the inflammatory cytokine interleukin-8 in explants specifically tattooed with the reference standard or red ink. Taken together, the results suggest that the tattooing technique leads to exposure to toxic metal NPs and skin damage. Full article

This work presents a simple process for the development of flexible acetone gas sensors based on zinc oxide/graphene/poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate). The gas sensors were prepared by inkjet printing, which was followed by a metal sparking process involving different sparking times. The successful decoration of ZnO nanoparticles (average size ~19.0 nm) on the surface of the graphene–PEDOT:PSS hybrid ink was determined by characterizations, including Raman spectroscopy, Fourier transform infrared spectroscopy, field-emission transmission electron microscopy, X-ray photoelectron spectroscopy, and X-ray diffractometry. The ZnO nanoparticle-decorated graphene–PEDOT:PSS with a sparking time of 2 min exhibited the highest response of 71.9% at 10 ppm of acetone, above those of samples treated with other sparking times and the undecorated control. In addition, the optimal sensor revealed high selectivity for acetone over several other kinds of gases, such as ammonia, toluene, dimethylformamide, ethanol, methanol, and benzene, at room temperature. The gas sensor also revealed a low limit of detection (0.4 ppm), high sensitivity (6.18 ppm⁻¹), and high stability (5-week long-term) to acetone. The response and recovery times of the sensor were found to be 4.6 min and 4.2 min, respectively. The acetone-sensing mechanism was attributed to the formation of p-n heterojunctions, which were responsible for the significantly enhanced sensitivity. Full article

The implementation of the laser sintering for inkjet-printed nanoparticles and metal organic decomposition (MOD) inks on a flexible polymeric film has been analyzed in detail. A novel approach by implementing, next to a commonly 3.2 mm diameter spot laser optic, a line laser optic with a laser beam area of 2 mm × 80 mm, demonstrates the high potential of selective laser sintering to proceed towards a fast and efficient sintering methodology in printed electronics. In this work, a multiplicity of laser parameters, primary the laser speed and the laser power, have been altered systematically to identify an optimal process window for each ink and to convert the dried and non-conductive patterns into conductive and functional silver structures. For each ink, as well as for the two laser optics, a suitable laser parameter set has been found, where a conductivity without any damage to the substrate or silver layer could be achieved. In doing so, the margin of the laser speed for both optics is ranging in between 50 mm/s and 100 mm/s, which is compatible with common inkjet printing speeds and facilitates an in-line laser sintering approach. Considering the laser power, the typical parameter range for the spot laser lays in between 10 W and 50 W, whereas for the line optics the full laser power of 200 W had to be applied. One of the nanoparticle silver inks exhibits, especially for the line laser optic, a conductivity of up to 2.22 × 10⁷ S‧m⁻¹, corresponding to 36% of bulk silver within a few seconds of sintering duration. Both laser sintering approaches together present a remarkable facility to use the laser either as a digital tool for sintering of defined areas by means of a spot beam or to efficiently sinter larger areas by means of a line beam. With this, the utilization of a laser sintering methodology was successfully validated as a promising approach for converting a variety of inkjet-printed silver patterns on a flexible polymeric substrate into functionalized conductive silver layers for applications in the field of printed electronics. Full article

The hybridization of single-walled carbon nanotubes (SWCNTs) and Cu nanoparticles offers a promising strategy for creating highly conductive and mechanically stable fillers for flexible printed electronics. In this study, we report the ultrafast synthesis of SWCNT/Cu hybrid nanostructures and the fabrication of flexible electrodes under ambient conditions through a laser-induced photo-thermal reaction. Thermal energy generated from the nonradiative relaxation of the π-plasmon resonance of SWCNTs was utilized to reduce the Cu-complex (known as a metal–organic decomposition ink) into Cu nanoparticles. We systematically investigated the effects of SWCNT concentration and output laser power on the structural and electrical properties of the SWCNT/Cu hybrid electrodes. The SWCNT/Cu electrodes achieved a minimum electrical resistivity of 46 μohm·cm, comparable to that of the metal-based printed electrodes. Mechanical bending tests demonstrated that the SWCNT/Cu electrodes were highly stable and durable, with no significant deformation observed even after 1000 bending cycles. Additionally, the electrodes showed rapid temperature increases and stable Joule heating performance, reaching temperatures of nearly 80 °C at an applied voltage of less than 3.5 V. Full article

This text discusses the synthesis of copper nanoparticles via a liquid phase reduction method, using ascorbic acid as a reducing agent and CuSO₄·5H₂O as the copper source. The synthesized copper nanoparticles are small in size, uniformly distributed, are mostly between 100–200 nm with clear boundaries between particles, and exhibit excellent dispersibility, making them suitable for metal conductive inks. 1. The copper nanoparticles are analyzed for good antioxidation properties, because their surface is coated with PVP and ascorbic acid. This organic layer somewhat isolates the particle surface from contact with air, preventing oxidation, and accounts for about 9% of the total weight. 2. When the prepared copper nanoparticles are spread on a polyimide substrate and sintered at 250 °C for 120 min, the resistivity can be as low as 23.5 μΩ·cm, and at 350 °C for 30 min, the resistivity is only three times that of bulk copper. 3. The prepared conductive ink, printed on a polyimide substrate using a direct writing tool, shows good flexibility before and after sintering. After sintering at 300 °C for 30 min and connecting the pattern to a circuit with a diode lamp, the diode lamp is successfully lit. 4. This method produces copper nanoparticles with small size, good dispersion, and antioxidation capabilities, and the conductive ink prepared from them demonstrates good conductivity after sintering. Full article

Among the conventional inks used for inkjet printing, metals, oxides, or polymers have been deposited in order to form functional coatings. Gold is one of the most used metals for electrode fabrication in the gas sensor field due to its inert behavior when exposed to reactive gases and conductive properties. However, only a few commercial gold inks are commercially available, and the combination of excessive price, a high minimum purchase quantity, and an unknown composition renders the actual products unappealing. To meet these shortcomings, gold inks were formulated with different solvents in order to reach sufficient properties for the inkjet printing process, such as surface tension and viscosity. On the one hand, gold ink was developed using a gold nanoparticle (AuNP) solution as the metal. This ink was optimized from nanoparticle synthesis, with the ink formulation obtaining a 32 mN·m⁻¹ surface tension and 11.2 mPa·s viscosity in order to be inkjet-printed onto polyimide foil. On the other hand, a particle-free ink, called a precursor based of ink, was also developed. In this case, ink was made by solubilizing gold salt in aqueous medium in order to reach jettable properties. Surface tension was measured at 32 mN·m⁻¹ while viscosity was 14.0 mPa·s. Then, printing and deposition parameters were optimized in order to obtain a highly conductive gold coating. The measured resistivity was 2 × 10⁻⁷ Ω·m which is close to the bulk gold conductive value. These coatings could be used for the fabrication of various devices in different working fields. Full article

In stealth applications, there is a growing emphasis on the development of radar-absorbing structures that are efficient, flexible, and optically transparent. This study proposes a screen-printed metamaterial absorber (MMA) on polyethylene terephthalate (PET) substrates using indium tin oxide (ITO) as the grounding layer, which achieves both optical transparency and flexibility. These materials and methods enhance the overall flexibility and transparency of MMA. To address the limited transparency caused by the silver nanoparticle ink for the top pattern, a metal mesh was incorporated to reduce the area ratio of the printed patterns, thereby enhancing transparency. By incrementing the fractal order of the structure, we optimized the operating frequency to target the X-band, which is most commonly used in radar detection. The proposed MMA demonstrates remarkable performance, with a measured absorption of 91.99% at 8.85 GHz and an average optical transmittance of 46.70% across the visible light spectrum (450 to 700 nm), indicating its potential for applications in transparent windows or drone stealth. Full article