Search Results (927)

In this study, we aimed to develop a high-performance, anti-fouling ultrafiltration membrane by integrating photocatalytic and Fenton-like functions into a polymer matrix, in order to address the critical challenge of membrane fouling and achieve simultaneous separation and degradation of organic pollutants. To this end, a novel Fe-V_O-TiO₂-embedded polyethersulfone (PES) composite membrane was designed and fabricated using a facile phase inversion method. The key innovation lies in the incorporation of Fe-V_O-TiO₂ nanoparticles containing abundant bulk-phase single-electron-trapped oxygen vacancies, which not only modulate membrane morphology and hydrophilicity but also enable sustained generation of reactive oxygen species for the pollutant degradation under light irradiation and H₂O₂. The optimized Fe-V_O-TiO₂-PES-0.04 membrane exhibited a significantly enhanced pure water flux of 222.6 L·m⁻²·h⁻¹ (2.2 times higher than the pure PES membrane) while maintaining a high bovine serum albumin (BSA) retention of 93% and an improved hydrophilic surface. More importantly, the membrane demonstrated efficient and stable synergistic Photocatalytic-Fenton activity, achieving 82% degradation of norfloxacin (NOR) and retaining 75% efficiency after eight consecutive cycles. A key finding is the membrane’s Photocatalytic-Fenton-assisted self-cleaning capability, with an 80% flux recovery after methylene blue (MB) fouling, which was attributed to in situ reactive oxygen species (·OH) generation (verified by ESR). This work provides a feasible strategy for designing multifunctional membranes with enhanced antifouling performance and extended service life through built-in catalytic self-cleaning. Full article

Recycling water offers a powerful way to lower the environmental water impact of mining activities. Pressure-retarded osmosis (PRO) represents a promising pathway for simultaneous water reuse and clean energy generation from salinity gradients. In this study, the performance of a thin-film nanocomposite (TFN) membrane containing functionalized multi-walled carbon nanotubes (fMWCNTs) within a polyacrylonitrile (PAN) support layer, followed by polydopamine (PDA) surface modification, was investigated under a PRO operation using pretreated gold mining wastewater as the feed solution. Unlike most previous studies that rely on synthetic feeds, this work evaluates the membrane performance under a PRO operation using a real mining wastewater stream. The membrane with fMWCNTs and PDA exhibited a maximum power density of 25.22 W/m² at 12 bar, representing performance improvements of 23% and 68% compared with the pristine thin-film composite (TFC) and commercial cellulose triacetate (CTA) membranes, respectively. A high water flux of 75.6 L·m⁻²·h⁻¹ was also obtained, attributed to enhanced membrane hydrophilicity and reduced internal concentration polarization. The optimized membrane, containing 0.3 wt% fMWCNTs in the support layer and a PDA coating on the active layer, produced a synergistic enhancement in the PRO performance, resulting in a lower reverse salt flux and an improved flux–selectivity trade-off. Furthermore, the ultrafiltration (UF) and nanofiltration (NF) pretreatment effectively reduced the hardness and ionic content, enabling a stable PRO operation with real mining wastewater over a longer period of time. Overall, this study demonstrates the feasibility of achieving both reusable water and enhanced osmotic power generation using modified TFN membranes under realistic mining wastewater conditions. Full article

This study investigated the influence of two years of ultrafiltration (UF) on the separation properties of tubular polyvinylidene fluoride membranes used for treating carwash wastewater, particularly with regard to bacterial rejection. Fouling was mitigated by washing the membranes with alkaline cleaning agents (pH > 11.5). Repeated applications of these agents enlarged the membrane pores to approximately 300 nm. This affected bacterial retention, and for feed containing bacteria (determined as colony-forming units, CFU) at a concentration of 3.11 × 10⁶ CFU/mL, over 13,000 CFU/mL were detected in the permeate. Interestingly, fouling improved retention, reducing bacterial counts present in the permeate from 13,689 to 2889 CFU/mL. Fouling also enhanced the retention of surfactants (80%), chemical oxide domain (60%), and turbidity (below 0.5 NTU), yielding results comparable to new membranes. Daily 60-min membrane washing with Wheel Cleaner solution (pH = 11.5) improved the membranes performance; however, it did not remove deposits from large pores, allowing good rejection performance and a permeate flux of 65 LMH to be maintained. It was found that bacteria also developed on the permeate side. Disinfection of the module housing with a NaOH/NaOCl solution reduced the number of bacteria in the permeate from 5356 to 66 CFU/mL. Microbiological tests revealed that some of these bacteria were antibiotic-resistant. Full article

Photocatalytic membrane reactors (PMRs) are an innovative technology for water treatment, effectively combining membrane filtration and photocatalysis to enhance contaminant removal while enabling the regeneration of fouled membranes. In this study, a new porous film of chitosan that was impregnated with TiO₂ was developed and coated onto a ceramic support by spin coating to form a new porous immobilized PMR. The formed membrane was tested for two reasons: the removal of methylene blue dye by a dead-end filtration process and to demonstrate its ability to self-regenerate under UV exposure. The selective layer of the membrane was characterized using FTIR spectroscopy, X-ray diffraction, scanning electron microscopy (SEM), and water permeability tests. The results confirmed the formation of an amorphous film with no chemical interaction between chitosan and TiO₂. The membrane exhibited an average water permeability of 10.72 L/m²·h·bar, classifying it as either ultrafiltration (UF) or nanofiltration (NF). Dead-end filtration of methylene blue (10 mg L⁻¹) achieved 99% dye removal based on UV–vis analysis of the permeate, while flux declined rapidly due to fouling. Subsequent UV irradiation removed the deposited dye layer and restored approximately 50% of the initial flux, indicating partial self-regeneration. Overall, spin-coated chitosan–TiO₂ layers on ceramic supports provide high dye removal and photocatalytically assisted flux recovery, and further work should quantify photocatalytic degradation during regeneration. Full article

Heavy metals released from industrial effluents accumulate in the human body through the ecosystem, causing several health disorders. This study investigated the removal of cadmium (Cd²⁺) using Micellar-Enhanced Ultrafiltration (MEUF). This study employed sodium dodecyl sulfate (SDS) and flat-sheet polyethersulfone (PES) ultrafiltration membranes to separate Cd²⁺ ions from lab-simulated water. The experiments involved examining the removal efficiency of membranes without SDS usage, optimizing SDS concentration for Cd²⁺ removal, and evaluating the long-term membrane performance. Other parameters include analyzing the removal percentage of varying Cd²⁺ at constant SDS dosage, examining the effect of pH, and electrolyte concentrations on the removal of Cd²⁺. Several analytical characterizations were performed, such as FT-IR, and SEM. The FTIR confirms the aromatic C-H group at 620–867 cm⁻¹, the sulfone group at 1100–1200 cm⁻¹, and the ether group at 1230–1270 cm⁻¹ and the SEM analysis indicates no significant fouling, which aligns with the stable flux observed over time. The result showed that the optimum SDS concentration for Cd²⁺ removal was 1 Critical Micellar Concentration (CMC), achieving over 99% removal. The presence of an electrolyte decreased Cd²⁺ removal efficiency, while the pH (3 to 9) had no effect on removal. Our findings suggest that the SDS-aided ultrafiltration process is suitable for eliminating Cd²⁺ from wastewater. Full article

Herein, we report the synthesis via controlled reversible addition-fragmentation chain transfer (RAFT) polymerization of amphiphilic 2-vinylpyridine-b-styrene (2VPy-b-Sty) diblock copolymers of high molar masses (range: 52,100–304,000 g mol⁻¹) and various compositions (range: 2VP content 11.6–59.2 mol%) and their use for the fabrication of nanoporous membranes. The successful synthesis of the amphiphilic diblock copolymers was confirmed through the characterization of their molar masses, molar mass distribution, and composition using GPC and ¹H-NMR spectroscopy, respectively. Subsequently, membranes of the diblock copolymers were fabricated following the “phase inversion” technique. The resulting membranes were characterized via scanning electron microscopy which revealed the presence of sphere percolation networks morphology for all diblock copolymers with M_n ranging from 120 to 300 kDa and 2VPy content between 10 and 15 mol% at the optimal conditions. Afterward, the developed membranes were evaluated in terms of their permeability towards water and in terms of their ability to retain two different microorganisms, namely, Enterococcus faecalis and Escherichia coli, that are known to be harmful to human health. The experimental water flux for a membrane with pore size around 60 nm was equal to 31,400 L h⁻¹ m² and expectedly decreased with the decrease in membrane pore diameter. The retention ability of membranes for Enterococcus faecalis and Escherichia coli was higher than 90%. In particular, the retention ability for Enterococcus faecalis was equal to 98.9% and for Escherichia coli was 91.4%. The toxicity of the produced membrane was also determined, and the measured value was relatively low, at 17%. Full article

In whey valorization, membrane separation stands out as a highly effective technique for purifying and isolating the various components of whey. The efficiency of whey ultrafiltration and diafiltration (UF/DF) largely depends on the balance between membrane selectivity, hydrodynamic conditions, and solute interactions at the membrane interface. In this study, sweet whey was fractioned using 10, 30 and 50 kDa polyether sulfone (PES) membranes under identical transmembrane pressure (TMP = 2.5 bar) with ultrafiltration and a subsequent 4-step constant volume diafiltration stages. The resulting compositional and dielectric changes were evaluated to identify optimal separation conditions and assess the applicability of dielectric parameter measurement as a rapid, non-destructive monitoring technique. Results showed that, regardless of the applied molecular weight cut-off (MWCO), using three DF cycles can wash out almost all the removable lactose from the retentates, and the dielectric assessment of both permeate and retentate fractions showed a strong, linear relationship between the change in dielectric behavior and the composition of each fraction. Analysis of the dielectric spectra confirmed that the ratio of the dielectric constant to the loss factor (ε′/ε″) exhibited a strong linear correlation (R² > 0.98, r > 0.99) with lactose concentration in the permeate fractions of all three MWCO membranes, as well as a similarly strong correlation (R² > 0.975, r > 0.98) with the total chemical oxygen demand (TCOD) measured in the retentate fractions. Full article

The study investigates the performance of polyethersulfone (PES) ultrafiltration (UF) membranes modified with a coating of polymerizable bicontinuous microemulsion (PBM) for membrane bioreactor (MBR) applications. Two types of PBM-modified PES membranes—casting-coated and spray-coated—were compared with a commercial PES membrane. A laboratory side-stream MBR (ssMBR) was employed to treat model wastewater (MW) with activated sludge under aerobic conditions. The fouling propensity of the membranes in ssMBR was evaluated through the implementation of two protocols: (i) flux-step test to treat low-strength domestic model wastewater (DMW) and (ii) constant flux test to treat high-strength olive mill model wastewater (OMW). The findings indicated that both the commercial PES and PBM spray-coated PES membranes started to critically foul at 36 L m⁻² h⁻¹. The PBM spray-coated membranes showed enhanced fouling resistance in comparison to the PBM casting-coated membranes. The deposition of the biofouling layer was the thinnest on PBM spray-coated membranes, which can be attributed to the low surface charge and high hydrophilicity of the modified membrane surface. In contrast, deposition of a thicker fouling layer was found on the commercial PES membrane, which can be attributed to the relatively higher surface charge promoting organic adsorption. A comparison of the fouling trends exhibited by commercial PES and PBM spray-coated membranes in OMW treatment revealed that they have similar fouling tendencies. However, a notable distinction emerged when the PBM spray-coated membrane was observed to demonstrate a lower fouling propensity accompanied by comparatively thinner fouling layers. The results demonstrate that the PBM spray-coated membranes have enhanced fouling resistance and filtration efficacy in MBRs treating wastewater with diverse strengths, thereby affirming their potential for application in wastewater treatment systems. Full article

Fouling is a major challenge in membrane-based filtration processes, leading to higher operating and capital costs. Developing new membranes with better fouling resistance has always been a research focus in the membrane field. In particular, designing functional surfaces which mitigate fouling is an effective approach. We successfully fabricated membranes with a graphene functional layer using a single-step laser irradiation known as laser-induced graphene (LIG) on the membrane surface. The LIG ultrafiltration (UF) membranes were prepared by directly lasing poly(ether sulfone) (PES) membrane substrates. Scanning electron microscopy demonstrated the successful ablation of the PES membranes with controlled thickness. Water filtration tests confirmed that the permeance increased by 240% as the laser power increased from 2.4 to 3.2 W; the membrane lased with the highest ablation power (LIG-P8) displayed a high water permeance of ~400 L m⁻² h⁻¹ bar⁻¹ and a corresponding bovine serum albumin (BSA) rejection of 92.5%. Fouling experiments using BSA, humic acid (HA), and sodium alginate showed better permeance recovery ratios (78–90%) with LIG membranes compared to the neat PES membrane (65–68%). LIG membranes were also evaluated for antibioufouling filtration tests, which showed exceptional biofilm resistance and potent antibacterial killing effects when treated with Staphylococcus aureus. Applied external voltage and contact time were the key variables to optimize the antibiofouling properties of the LIG UF membranes. Full article

Microplastics represent a pressing global environmental concern due to their persistence, widespread occurrence, and adverse impacts on aquatic ecosystems and human health. Effective removal of these contaminants from water is essential to safeguard biodiversity and ensure water quality. This work focuses on the pivotal role of membrane-based filtration technologies, including microfiltration, ultrafiltration, nanofiltration, reverse osmosis, membrane bioreactors, and dynamic membranes, in capturing and eliminating microplastics. The performance of these systems depends on key membrane characteristics such as pore size, material composition, hydrophilicity, mechanical strength, and module design, which govern retention efficiency, fouling resistance, and operational stability. Membrane filtration offers a highly effective, scalable, and sustainable approach to microplastic removal, outperforming conventional treatment methods by selectively targeting a wide range of particle sizes and morphologies. By highlighting the critical contribution of membranes and filtration processes, this study underscores their potential in mitigating microplastic pollution and advancing sustainable water treatment practices. Full article

New approaches to the characterization of porous materials must satisfy principles of green analytical chemistry; in addition, they should be reproducible, versatile, and capable of providing relevant information for specific applications. Membrane characterization techniques often fail to meet some of these requirements. Specifically, hydrodynamic porous-based model methods (HPMMs) enable the simulation and evaluation of membrane properties, as well as the monitoring of changes in the response to controlled and uncontrolled modifications. Nevertheless, HPMMs are limited by the multifactorial relationships between their variables and by the generation of only single-value responses. Here, a semi-empirical approach to the characterization of membrane pore structure is proposed and evaluated using simple experimental measurements from pristine and modified membranes. The model enables the determination of the effective pore radius based on two size descriptors related to porosity and permeability, the construction of pore size distributions, and the estimation of structural parameters, such as the number of pores, pore size, and surface porosity. Furthermore, it allows for the simulation of Darcy-type flow behavior in both linear and nonlinear regimes. The model was evaluated on pristine and poly(vinyl alcohol)-modified poly(ethersulfone) ultrafiltration membranes (60–120 mmolL⁻¹) by diafiltration (100–400 kPa). Results demonstrate the usefulness of the model in characterizing membrane pore structure by using simple, fast, and non-destructive methods, thereby enabling advances in analytical diafiltration for membrane characterization. Full article

Sea cucumber peptides have been shown to possess a number of functions, including antioxidant, anti-inflammatory, anti-tumor, and anti-fatigue effects, as well as immune regulation and promotion of collagen synthesis. Among these, high F-value oligopeptides are a promising natural active ingredient demonstrating excellent anti-fatigue effects. This study utilized fresh sea cucumbers as the primary raw material, employing membrane separation technology to investigate the simultaneous separation of sea cucumber polysaccharides and peptides. The process for removing aromatic amino acids during the preparation of high F-value oligopeptides from sea cucumbers was optimized, and the mechanism underlying their anti-fatigue effects was explored. A two-step enzymatic hydrolysis method using neutral protease and composite flavor protease was employed, followed by membrane separation using a 10,000 Da molecular weight ultrafiltration membrane, yielding a sea cucumber peptide yield of 45.00 ± 0.12% and a sea cucumber polysaccharide yield of 51.28 ± 0.63%. Following the removal of aromatic amino acids by means of activated carbon adsorption, the F-value of the high-F-value oligopeptides attained 23.82, with a yield of 24.56%. The experimental findings demonstrated that high-F-value oligopeptides exhibited a substantial increase in the swimming duration of mice and a notable enhancement in their grip strength. These observations signified their substantial anti-fatigue potential. Furthermore, studies have indicated that sea cucumber high-F-value oligopeptides reduce metabolites produced by exercise, enhance muscle protection, increase the activity of antioxidant enzymes in the body, and alleviate fatigue, thereby achieving an anti-fatigue effect. Full article

Cationic surfactants from the group of quaternary ammonium compounds (QACs) are widely used in disinfectants, cosmetics, and household and industrial products. Their strong antimicrobial activity and chemical stability make them valuable in applications but also highly persistent and toxic when released into aquatic environments. This problem has become increasingly relevant during and after the COVID-19 pandemic, when global use of QAC-based disinfectants increased drastically, resulting in their frequent detection in municipal, hospital, and industrial effluents. The concentrations of QACs reported in wastewater range from trace levels to several mg/L, often reaching inhibitory thresholds for biological treatment processes. Although surfactants are not listed in any current European directive, the revised Directive (EU) 2024/1440 classifies micropollutants as a priority group, imposing stricter environmental quality standards and mandatory monitoring requirements. Within this regulatory framework, QACs are recognized as compounds of emerging concern, and their effective removal from wastewater has become a critical challenge. This review summarizes the current knowledge on conventional treatment technologies (coagulation, adsorption, ion exchange, advanced oxidation, and biological processes) and membrane-based methods (ultrafiltration, nanofiltration, reverse osmosis, forward osmosis, and hybrid systems) for the removal of cationic surfactants from water and wastewater. Mechanisms of separation, performance, and operational limitations are discussed. Full article

Extracellular vesicles (EVs) secreted by Fusarium oxysporum play an important role in the process of its infestation of the host, but the in vitro research system for EVs of F. oxysporum (Fo-EVs) has not yet been improved, and the mechanism of its action remains unclear. In this study, particle size distribution, particle concentration, number of particles per unit of protein, number of particles per unit of mycelial biomass, and concentration of contaminated proteins were used as indicators to evaluate the yield and purity of Fo-EVs. The optimal method for Fo-EV preparation and extraction was screened by comparing liquid culture, solid culture, and solid culture with enzymatic cell wall hydrolysis. The optimal system for Fo-EVs separation and purification was screened by a pairwise combination of three primary methods (Ultracentrifugation (UC), Ultrafiltration (UF), and Polyethylene glycol precipitation method (PEG)) and two secondary methods (Size-exclusion chromatography (SEC) and Aqueous two-phase system (ATPS)), respectively. The protein composition was identified via mass spectrometry technology, followed by GO annotation and GO enrichment analysis using whole-genome proteins as the background. Based on these steps, a Fo-EV protein library was constructed to reveal Fo-EV’s most active biological functions. The results showed that solid culture combined with the UC-SEC method could effectively enrich Fo-EVs with a typical cup-shaped membrane structure. The obtained Fo-EVs had an average particle size of 253.50 nm, a main peak value of 200.60 nm, a particle concentration of 2.04 × 10¹⁰ particles/mL, and a particle number per unit protein of 1.09 × 10⁸ particles/μg, which were significantly superior to those of other combined methods. Through proteomic analysis, 1931 proteins enriched in Fo-EVs were identified, among which 350 contained signal peptides and 375 had transmembrane domains. GO enrichment analysis revealed that these proteins were mainly involved in cell wall synthesis, vesicle transport, and pathogenicity-related metabolic pathways. Additionally, 9 potential fungal EV markers, including Hsp70, Rho GTPase family, and SNARE proteins, were screened. This study constructed an isolation system and a marker database for Fo-EVs, providing a methodological and theoretical basis for in-depth analysis of the biological functions of Fo-EVs. Full article

This study focuses on polysaccharides from Cistanche deserticola and Cistanche tubulosa, medicinal plants renowned for their health benefits. The “water extraction and alcohol precipitation” method was used to obtain the crude polysaccharides of the wine-making residues of C. deserticola (CDP) and C. tubulosa (CTP), respectively. Then, ultrafiltration membrane (UFM), DEAE-52, and Sephadex-G75 or Smartdex-G100 gel chromatography were used to separate and purify the crude polysaccharides, yielding the homogeneous fractions CDP1-5-1, CDP2-2-2, CDP2-3-2, CTP1-5-1, and CTP1-5-3. Structural analysis was conducted by using Fourier-transform infrared spectroscopy (FT-IR), high-performance anion-exchange chromatography coupled with multi-angle laser light scattering and refractive index detection (HPAEC-MALLS-RID), gas chromatography–mass spectrometry (GC-MS), nuclear magnetic resonance (NMR), congo red, and scanning electron microscopy (SEM). CDP1-5-1 was found to be an arabinan, while CDP2-2-2 and CDP2-3-2 were agavin-like fructans with different molecular weights. CTP1-5-1 and CTP1-5-3 were identified as a heteropolysaccharide and a galacturonan, respectively. Immunological evaluation using RAW264.7 macrophages showed that they all significantly enhanced nitric oxide (NO) production, with CDP1-5-1 exhibiting the most potent activity. The structural–activity relationship is summarized as follows: the arabinose was a key active unit with NO stimulatory effects. This research provides foundational data on the structure and immune-enhancing potential of Cistanche polysaccharides, supporting their further development and application. Full article