Search Results (145)

Background/Objectives: A stem cell therapy for type 1 diabetes (T1D) is experimentally available but only to those few humans in whom the use of systemic immunosuppression can be justified. For others with T1D, a means to deliver the islets needs to be perfected. We have previously bioengineered a removable device for this purpose and now wish to test the effect of adding extracellular matrix (ECM) derived from decellularised human pancreas to it. Methods: The complete device consists of encapsulated pluripotent stem cell differentiated islets seeded into tubular scaffolds of polycaprolactone made by melt electrospin writing and to which ECM was added. The seeded device was implanted either subcutaneously (SC) or intraperitoneally (IP) into streptozotocin diabetic immunodeficient mice. The outcome over the next few months was compared with that achieved in diabetic mice implanted IP with encapsulated islets alone. Results: The device seeded with encapsulated islets but not containing ECM functioned less well than encapsulated islets implanted alone, with lower human C-peptide production. However, when ECM was added to the seeded device and whether implanted SC or IP, islets functioned as efficiently as those implanted without use of a scaffold. Conclusions: These data provide optimism for the use of seeded scaffolds in diabetic humans in whom a single scaffold seeded with multiple encapsulated islets can more readily be removed if needed for safety reasons than can multiple encapsulated islets not seeded into a scaffold. Full article

Electrospinning, Forcespinning^®, and melt electrowriting are becoming increasingly important fiber-based fabrication technologies for tissue engineering and drug delivery applications. Despite their scientific and industrial relevance, their patent landscape has not been systematically examined, which limits the understanding of technological dynamics and translational applications. This study addresses this gap through a patentometric analysis conducted within a Competitive Technology Intelligence framework. A total of 3557 active and granted Extended Patent Families from 2020 to 2024 were analyzed to identify temporal patterns, geographic distribution, key innovators, industrial sectors, and primary application areas. The results showed that the overall patent activity increased until 2022 before experiencing a slight decline. China dominates the landscape, accounting for approximately 62% of applications filed, largely driven by academic institutions such as Shanghai University. Leading industries include special-purpose machinery, medical and dental technology, and textiles. According to International Patent Classification codes, filament formation (D01D5/00) is prevalent, while electrospinning—specifically IPC D04H1/728—represents the most active and influential of the three technologies. These findings exhibit the technological dynamics shaping fiber-based fabrication platforms and underscore their growing relevance in pharmaceutical innovation. The identified trends position these technologies as foundational for next-generation biomaterial design, offering valuable insights for researchers, industry stakeholders, and policymakers. Full article

Electrospun fibrous scaffolds based on cellulose acetate (CA), polycaprolactone (PCL), and poly (L-lactic acid) (PLLA) are versatile materials with applications spanning diverse fields, but in their pristine form, they typically lack significant inherent antibacterial properties. To address this limitation and expand their utility, this study explored the incorporation of xylitol, a natural antibacterial sugar alcohol, into these polymer matrices to enhance their physicochemical and antimicrobial properties. Electrospinning was employed to fabricate pristine and xylitol-loaded scaffolds with varying xylitol concentrations. Morphological analysis revealed polymer-dependent changes in fiber diameter and porosity. Mechanical testing assessed the impact of xylitol on tensile properties, while thermal analysis investigated alterations in melting temperature and crystallinity. The antibacterial efficacy against Staphylococcus aureus and Escherichia coli was evaluated using WST assay and live/dead staining. Notably, xylitol significantly enhanced the antibacterial activity against both bacterial species, with a more pronounced and rapid effect observed against S. aureus. The tailored scaffold properties and imparted antimicrobial characteristics highlight the potential of these xylitol-modified electrospun materials: they are easily produced, low-cost, and appropriate for a range of applications (dental applications, filters, masks, wound dressing, and packaging) where preventing bacterial contamination is crucial. Full article

Background: Sustained-release (SR) formulations of non-steroidal anti-inflammatory drugs (NSAIDs) aim to prolong therapeutic activity, reduce dosing frequency, and improve patient adherence. However, currently marketed SR NSAIDs exhibit persistent limitations, including incomplete control over release kinetics, high interpatient variability in bioavailability, limited reduction in gastrointestinal adverse effects, and insufficient dose flexibility for individualized therapy. In many cases, conventional excipients and release mechanisms remain predominant, leaving drug-specific physicochemical and pharmacokinetic constraints only partially addressed. These gaps highlight the need for a comprehensive synthesis of recent technological advances to guide the development of more effective, patient-centered delivery systems. Methods: A narrative literature review was conducted using Web of Science and PubMed databases to identify original research articles and comprehensive technological studies on oral SR formulations of NSAIDs and paracetamol published between January 2020 and March 2025. Inclusion criteria focused on preclinical and technological research addressing formulation design, excipient innovations, and manufacturing approaches. Results: Sixty-four studies met the inclusion criteria, encompassing polymeric matrices (31%), lipid-based carriers (18%), microspheres/hydrogel beads/interpenetrating polymer networks (30%), nanostructured systems (11%), and hybrid platforms (10%). The most common strategies involved pH-dependent release, mucoadhesive systems, and floating drug delivery, aiming to optimize release kinetics, minimize mucosal irritation, and sustain therapeutic plasma levels. Advances in manufacturing—such as hot-melt extrusion, 3D printing, electrospinning, and spray drying—enabled enhanced control of drug release profiles, improved stability, and in some cases up to 30–50% prolongation of release time or reduction in Cmax fluctuations compared with conventional formulations. Conclusions: Recent formulation strategies show substantial potential to overcome long-standing limitations of SR NSAID delivery, with expected benefits for patient compliance and quality of life through reduced dosing frequency, better tolerability, and more predictable therapeutic effects. Nevertheless, integration of in vitro performance with pharmacokinetic and clinical safety outcomes remains limited, and the translation to clinical practice is still in its early stages. This review provides a comprehensive overview of current technological trends, identifies persisting gaps, and proposes future research directions to advance SR NSAID systems toward safer, more effective, and patient-focused therapy. Full article

Cardiovascular diseases pose a significant global health burden, driving the need for artificial vascular grafts to address limitations of autologous and allogeneic vessels. This review examines the integration of fiber materials and textile technologies in vascular tissue engineering, focusing on structural mimicry and functional regeneration of native blood vessels. Traditional textile techniques (weaving, knitting, and braiding) and advanced methods (electrospinning, melt electrowriting, wet spinning, and gel spinning) enable the fabrication of fibrous scaffolds with hierarchical architectures resembling the extracellular matrix. The convergence of textile technology and fiber materials holds promise for next-generation grafts that integrate seamlessly with host tissue, addressing unmet clinical needs in vascular tissue regeneration. Full article

The growing demand for sustainable materials has led to increased interest in biodegradable polymer fibers and nonwoven mats due to their eco-friendly characteristics and potential to reduce plastic pollution. This review highlights how mechanical properties influence the performance and suitability of biodegradable polymer fibers across diverse applications. This covers synthetic polymers such as polylactic acid (PLA), polyhydroxyalkanoates (PHAs), polycaprolactone (PCL), polyglycolic acid (PGA), and polyvinyl alcohol (PVA), as well as natural polymers including chitosan, collagen, cellulose, alginate, silk fibroin, and starch-based polymers. A range of fiber production methods is discussed, including electrospinning, centrifugal spinning, spunbonding, melt blowing, melt spinning, and wet spinning, with attention to how each technique influences tensile strength, elongation, and modulus. The review also addresses advances in composite fibers, nanoparticle incorporation, crosslinking methods, and post-processing strategies that improve mechanical behavior. In addition, mechanical testing techniques such as tensile test machine, atomic force microscopy, and dynamic mechanical analysis are examined to show how fabrication parameters influence fiber performance. This review examines the mechanical performance of biodegradable polymer fibers and fibrous mats, emphasizing their potential as sustainable alternatives to conventional materials in applications such as tissue engineering, drug delivery, medical implants, wound dressings, packaging, and filtration. Full article

The effect of annealing on the microstructure and tensile properties of low-density polyethylene (LDPE) non-woven fabric produced by melt electrospinning was systematically investigated using DSC, SAXS, SEM, etc. The results showed that, above an annealing temperature of 80 $°\mathrm{C}$, both the main melting point and crystallinity of LDPE decreased compared to the original sample, as did the tensile strength of the non-woven fabric. Additionally, the lamellar distribution became broader at annealing temperatures above 80 $°\mathrm{C}$. The recrystallization mechanism of molten lamellae (disordered chains) in LDPE was elucidated by fitting the data using a Gaussian function. It was found that secondary crystallization, forming thicker lamellae, and spontaneous crystallization, forming thinner lamellae, occurred simultaneously at rates dependent on the annealing temperature. Secondary crystallization dominated at temperatures ≤80 $°\mathrm{C}$, whereas spontaneous crystallization prevailed at temperatures above 80 $°\mathrm{C}$. These findings explain the observed changes in the microstructure and tensile properties of the LDPE non-woven fabric. Furthermore, a physical model describing the microstructural evolution of the LDPE non-woven fabric during annealing was proposed based on the experimental evidence. Full article

In recent years, pelvic organ prolapse (POP) cases have been rising, affecting women’s quality of life. Synthetic surgical transvaginal meshes used for POP treatment were withdrawn from the United States market in 2019 due to high risks, including infection, vaginal mesh erosion, and POP reoccurrence. Biodegradable mesh implants with three-dimensional printing technology have emerged as an innovative alternative. In this study, polycaprolactone (PCL) meshes for POP repair were fabricated using melt electrospinning writing (MEW) and mechanically evaluated through uniaxial tensile tests. Following this, they were coated with antibiotics—azithromycin, gentamicin sulfate, and ciprofloxacin—commonly used for genitourinary tract infections. Zone inhibition and biofilm assays evaluated antibiotic effectiveness in preventing mesh infections by Escherichia coli, and methicillin-susceptible (MSSA) and methicillin-resistant (MRSA) Staphylococcus aureus. The meshes presented a mechanical behavior closer to vaginal tissue than commercially available meshes. Fourier transform infrared analysis confirmed antibiotic incorporation. Ciprofloxacin demonstrated antibacterial activity against MRSA, with a 92% reduction in metabolic activity and a 99% biomass reduction. Gentamicin and ciprofloxacin displayed inhibitory activity against MSSA and E. coli. Scanning electron microscopy images support these conclusions. This methodology may offer a more effective, patient-friendly solution for POP repair, improving healing and the quality of life for affected women. Full article

The article describes obtaining polyacrylonitrile (PAN) nanofibers by electrospinning on a setup developed at the Mendeleev University of Chemical Technology of Russia (MUCTR). A technique for producing PAN-based carbon nanofibers (CNFs) and PAN-based CNFs modified with titanium oxide (TiO₂) is presented. The article presents a comprehensive study of the characteristics of PAN-based nanofibers and CNFs, including an analysis of the external structure of the fibers, the dependence of fiber diameters on the viscosity of the initial solutions, the effect of temperature treatment on the functional groups of PAN, elemental analysis, and flame-retardant properties. It was found that the fiber diameter and its external structure strongly depend on the viscosity of the initial solutions; an increase in viscosity leads to a linear increase in the fiber diameter. Preliminary temperature treatment at 250 °C helps stabilize PAN nanofibers and prevents their melting at the carbonization stage. The differential scanning calorimetry results allowed us to determine the presence of peaks for the initial PAN nanofibers, indicating an exothermic process in the temperature range of 290–320 °C. The peak height decreased with increasing TiO₂ concentration in the samples. For CNF samples of different compositions, the endothermic effect prevailed in the temperature range of 400–700 °C, indicating the possible flame-retardant properties of these materials. The limiting oxygen index (LOI) was calculated based on the thermogravimetric analysis results. The highest LOI values were obtained for CNFs based on PAN without adding TiO₂ nanoparticles and CNFs modified with TiO₂ (3 wt.%). The resulting CNF-based nonwovens can be recommended for use in heat-protective clothing, flame-retardant mattresses, and flame-retardant suits for the military. Full article

Polyphenylene sulfide (PPS)-based separators have garnered significant attention as high-performance components for next-generation lithium-ion batteries (LIBs), driven by their exceptional thermal stability (>260 °C), chemical inertness, and mechanical durability. This review comprehensively examines advances in PPS separator design, focusing on two structurally distinct categories: porous separators engineered via wet-chemical methods (e.g., melt-blown spinning, electrospinning, thermally induced phase separation) and nonporous solid-state separators fabricated through solvent-free dry-film processes. Porous variants, typified by submicron pore architectures (<1 μm), enable electrolyte-mediated ion transport with ionic conductivities up to >1 mS·cm⁻¹ at >55% porosity, while their nonporous counterparts leverage crystalline sulfur-atom alignment and trace electrolyte infiltration to establish solid–liquid biphasic conduction pathways, achieving ion transference numbers >0.8 and homogenized lithium flux. Dry-processed solid-state PPS separators demonstrate unparalleled thermal dimensional stability (<2% shrinkage at 280 °C) and mitigate dendrite propagation through uniform electric field distribution, as evidenced by COMSOL simulations showing stable Li deposition under Cu particle contamination. Despite these advancements, challenges persist in reconciling thickness constraints (<25 μm) with mechanical robustness, scaling solvent-free manufacturing, and reducing costs. Innovations in ultra-thin formats (<20 μm) with self-healing polymer networks, coupled with compatibility extensions to sodium/zinc-ion systems, are identified as critical pathways for advancing PPS separators. By addressing these challenges, PPS-based architectures hold transformative potential for enabling high-energy-density (>500 Wh·kg⁻¹), intrinsically safe energy storage systems, particularly in applications demanding extreme operational reliability such as electric vehicles and grid-scale storage. Full article

Bacterial cellulose (BC) is a highly pure and crystalline cellulose produced via bacterial fermentation. However, due to its chemical structure made of strong hydrogen bonds and its high molecular weight, BC can neither be melted nor dissolved by common solvents. Therefore, processing BC implies the use of very strong, often toxic and dangerous chemicals. In this study, we proved a green method to produce electrospun BC fibers by testing different ionic liquids (ILs), namely, 1-butyl-3-methylimidazolium acetate (BmimAc), 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (EmimTFSI) and 1-ethyl-3-methylimidazolium dicyanamide (EmimDCA), either individually or as binary mixtures. Moreover, γ-valerolactone (GVL) was tested as a co-solvent derived from renewable sources to replace dimethyl sulfoxide (DMSO), aimed at making the viscosity of the cellulose solutions suitable for electrospinning. A BmimAc and BmimAc/EmimTFSI (1:1 w/w) mixture could dissolve BC up to 3 w%. GVL was successfully applied in combination with BmimAc as an alternative to DMSO. By optimizing the electrospinning parameters, meshes of continuous BC fibers, with average diameters ~0.5 μm, were produced, showing well-defined pore structures and higher water absorption capacity than pristine BC. The results demonstrated that BC could be dissolved and electrospun via a BmimAc/GVL solvent system, obtaining ultrafine fibers with defined morphology, thus suggesting possible greener methods for cellulose processing. Full article

Air filters are crucial components of building ventilation systems. Compared to conventional air filter media like glass fibers and melt-blown fibers, electrospinning membranes are more efficient for capturing various pollutants due to the smaller pores present on the structure. In this paper, activated carbon filters were prepared with eco-friendly polylactic acid (PLA) and microcrystalline cellulose (MCC) using electrospinning to obtain a high-quality factor (QF) fibrous mat for aerosol particle matter (PM) filtration and volatile organic compounds (VOCs) adsorption. Several configurations of the final membranes were investigated and tested for fiber morphology and air filtration performance. Filtering efficiency and adsorption properties were evaluated in a real-scale room by measuring the particle penetration of the newly synthesized and commercial filters against neutralized aerosol particles (3% NaCl aqueous solution) and VOCs (methyl ethyl ketone). The calculated depolluting efficiencies were up to 98% in terms of PM and 55% for VOCs abatement, respectively. Our results indicate that the proposed hybrid membranes represent promising materials for highly efficient and sustainable air filters for home application systems. Full article

Fused Deposition Modeling (FDM) is a prominent additive manufacturing technique known for its ability to provide cost-effective and fast printing solutions. FDM enables the production of computer-aided 3D designs as solid objects at macro scales with high-precision alignment while sacrificing excellent surface smoothness compared to other 3D printing techniques such as SLA (Stereolithography) and SLS (Selective Laser Sintering). Electro-Spinning (ES) is another technique for producing soft-structured nonwoven micro-scale materials, such as nanofibers. However, compared to the FDM technique, it has limited accuracy and sensitivity regarding high-precision alignment. The need for high-precision alignment of micro-scaled soft structures during the printing process raises the question of whether FDM and ES techniques can be combined. Today, the printing technique with such capability is called Melt Electro Writing (MEW), and in practice, it refers to the basic working principle on which bio-printers are based. This paper aims to examine how these two techniques can be combined affordably. Comparatively, it presents output production processes, design components, parameters, and materials used in output production. It discusses the limitations and advantages of such a hybrid platform, specifically from the perspective of engineering design and its biomedical applications. Full article

Poor water solubility remains a significant challenge in the pharmaceutical industry that limits the therapeutic efficacy and bioavailability of many active pharmaceuticals. Soluplus^® (SLP), an amphiphilic graft copolymer made of polyethylene glycol, polyvinyl caprolactam, and polyvinyl acetate, has been gaining interest in recent years as it addresses these limitations by acting as a versatile carrier. Its ability to form stable amorphous dispersions and enhance drug solubility, as well as its physicochemical properties, support its role as a key excipient in advanced drug delivery systems. Recent investigations have demonstrated the adaptability of SLP in addressing drug delivery requirements, offering controlled release, improved targeting, and superior therapeutic outcomes. This review examines some key formulation methods that make use of SLP, including hot-melt extrusion, spray drying, electrospinning, drug–polymer layering, and capsule and tablet formulations, highlighting the capacity of SLP to overcome formulation challenges. Biomedical applications of SLP have also been explored, with a focus on its role in improving the delivery of antitumoral, anti-inflammatory, antimicrobial, and antiparasitic drugs. Full article

Biodegradable polylactic acid (PLA) was used to fabricate nonwoven fabrics via the melt blowing process, followed by electrospinning to deposit a nanofiber membrane. This composite process yielded PLA melt-blown/electrospun composite materials with excellent filtration performance. The effects of the solution concentration and spinning duration on the composite structure and material performance were investigated. The optimal composite was produced using a 10 wt.% PLA spinning solution prepared with a solvent mixture of dichloromethane (DCM) and N, N-dimethylformamide (DMF) in a 75/25 weight ratio. The process parameters included a spinning duration of 5 h, 18 kV voltage, 1.5 mL/h flow rate, and 12 cm collection distance. The resulting composite achieved a filtration efficiency of 98.7%, a pressure drop of 142 Pa, an average pore size of 5 μm, and a contact angle of 138.7°. These results provided optimal process parameters for preparing PLA melt-blown/electrospun composite filtration materials. This study highlights the potential of hydrophobic PLA composites with high filtration efficiency and low air resistance as environmentally friendly alternatives to traditional non-degradable filtration materials. Full article