Search Results (101)

Due to the large amount of plastic waste that is currently produced, the demand for ecological solutions to this situation has been growing. Many research studies in recent years have focused on polylactic acid (PLA) as a biodegradable material made from renewable resources. The individual components of biodegradable materials should comply with the EN 13432 standard, which defines the properties of a “compostable” material. Careful selection of dyes and pigments is therefore important in terms of maintaining the biodegradability of the finished products. In this article, we focus on evaluating the flow properties of color masterbatches modified with inorganic biodegradable pigments. Two types of PLA were used as polymer pigment carriers, and titanium dioxide, carbon black, and two iron oxides were used as inorganic pigments. We monitored the effect of the type and concentration of pigments on the processability and rheological properties of the prepared color PLA masterbatches. The capillary viscometer and rotary rheoviscometer were used to determine rheological properties. The flow properties of color masterbatches containing 1 and 3 wt.% inorganic pigments with two types of pure polymers, PLA6100 and PLA175, were compared. We found that the color PLA masterbatches had good processability and satisfactory rheological properties, and therefore they are usable for further processing. Full article

In this study, we present experimental investigations of the surface structure and water contact angles of magnetoactive elastomers (MAEs), which are controlled by an external magnetic field. Specifically, we examine how the polymer matrix architecture affects the surface roughness and wettability of MAEs in various magnetic fields. We performed a comparative analysis on MAEs based on a linear polysiloxane network and on a matrix of the same chemical nature containing side-grafted chains. We synthesized a series of magnetoactive elastomers containing 75 wt.% carbonyl iron and varying amounts of a low-molecular-weight plasticizer. Although the magnetorheological effect is higher for traditional linear MAEs, we found that the magnetic response in surface properties is higher for novel MAEs with side-grafted chains. The largest increase in water contact angle was observed in the side-chain MAEs with the highest 60 wt.% plasticizer content: rising from 112° in a zero field to 168° in a 490 mT magnetic field. Water contact angles exhibit greater stability over time for side-chain MAEs, and this stability further increases in the presence of a magnetic field. Our results demonstrate that the architecture of the polymer matrix serves as an effective tool for designing smart, magnetically responsive surfaces. Full article

In this study, a selection of active materials were coated onto commercially available intermediate modulus carbon fibers to form and analyze the performance of novel composite cathodes for structural power composites. Various slurries containing polyvinylidene fluoride (PVDF), active material powders, 1-methyl-2-pyrrolidone (NMP) and carbon black (CB) were used to coat carbon fiber tows by immersion. Four active materials—lithium cobalt oxide (LCO), lithium iron phosphate (LFP), lithium nickel manganese cobalt oxide (NMC), and lithium nickel cobalt aluminum oxide (NCA)—were individually tested to assess their electrochemical reversibility. The cells were prepared with a polymer separator and liquid electrolytes and assembled in 2025-coin cells. Electrochemical analysis of the cathode materials showed that at C/5 and room temperature the measured capacities ranged from 39.8 Ah kg⁻¹ to 64.7 Ah kg⁻¹ for the LFP and NCA active materials, respectively. The full cells exhibited capacities of 18.1, 23.5, 27.2, and 28.2 Ah kg⁻¹ after 55 cycles for LFP, LCO, NCA, and NMC811, respectively. Finally, visual and elemental analysis were performed via scanning electron microscope (SEM) and energy-dispersive x-ray (EDX) confirming desirable surface coverage and successful transfer of the active materials onto the carbon fiber tows. Full article

Heavy metal contamination in natural waters and soils poses a significant environmental challenge, necessitating efficient and sustainable water treatment solutions. This study presents the computational design of low-density polyethylene (LDPE) films functionalized with iron oxide (Fe₃O₄) nanoparticles (NPs) for enhanced water purification applications. Composite materials containing 5%, 10%, and 15% were synthesized and characterized in terms of adsorption efficiency, surface morphology, and reusability. Advanced molecular modeling using BIOVIA Pipeline was employed to investigate charge distribution, functional group behaviour, and atomic-scale interactions between polymer chains and metal ions. The computational results revealed structure–property relationships crucial for optimizing adsorption performance and understanding geochemically driven interaction mechanisms. The LDPE/Fe₃O₄ composites demonstrated significant removal efficiency of Cu²⁺ and Ni²⁺ ions, along with favourable mechanical properties and regeneration potential. These findings highlight the synergistic role of mineral–polymer interfaces in water remediation, presenting a scalable approach to designing multifunctional polymeric materials for environmental applications. This study contributes to the growing field of polymer-based adsorbents, reinforcing their value in sustainable water treatment technologies and environmental protection efforts. Full article

This study discloses the noncovalent immobilization of a bienzyme cascade composed of glucose oxidase (GOx) and horseradish peroxidase (HRP) onto magnetically responsive polyamide microparticles (PA MPs). Porous PA6, PA4, and PA12 MPs containing iron fillers were synthesized via activated anionic ring-opening polymerization in suspension, alongside neat PA6 MPs used as a reference. Four hybrid catalytic systems (GOx/HRP@PA) were prepared through sequential adsorption of HRP and GOx onto the various PA MP supports. The initial morphologies of the supports and the hybrid biocatalysts were characterized by SEM, followed by evaluation of the catalytic performance using a two-step glucose oxidation cascade process. Among all systems, the GOx/HRP@PA4-Fe complex exhibited the highest activity, being approximately 1.5 times greater than the native enzyme dyad, followed by the PA6-supported system with slightly inferior performance. All systems obeyed Michaelis–Menten kinetics, with the immobilized cascades displaying higher Kₘ and Vₘₐₓ values than the non-immobilized enzyme pair while maintaining comparable catalytic efficiencies, CE (CE = k_cat/Kₘ). Subsequently, the immobilized and native enzyme systems were employed for the polymerization of aniline. According to UV–VIS, complete monomer conversion was achieved within 24 h for selected catalysts, and FTIR analysis confirmed the formation of polyaniline in the emeraldine base form without the use of template molecules. These findings highlight the potential of Fe-containing polyamide microparticles as efficient supports for the sustainable, enzyme-mediated synthesis of intrinsically conductive aromatic polymers. Full article

Sourcing and batch differences are often cited as intrinsic drawbacks for all natural polymers. Chitosan makes no exception. Chitosan is a biocompatible and biodegradable biopolymer with high potential for several biomedical applications, especially for releasing drugs and bactericidal and virucidal agents. Despite the potential of chitosan as a matrix for producing antibacterial films, the variability in its composition, stemming from its natural sources, can hinder the translation from bench to industry. To overcome this concern, we conducted a study to access the interchangeability of chitosan for the development of antibacterial drug release systems, in particular one system crosslinked with tannic acid and iron sulfate. Chitosans from different suppliers were characterized and used to synthetize films containing gentamicin, according to a previously reported protocol. The impact of molecular weight (M_W), deacetylation degree and purity on film properties and antibiotic release kinetics was assessed and results were compared. The films exhibited different initial bursts followed by similar sustained release profiles. All films exhibited antibacterial activity against both E. coli and S. aureus for at least 42 days. Moreover, films were cyto- and hemocompatible. Therefore, despite some differences in physicochemical properties, the interchangeability among the studied chitosan suppliers to produce antibacterial films is feasible, and the final product properties and performances are not significantly altered. Full article

The aim of this research was to obtain two-layer polymer composites with favorable mechanical and functional properties. The composites consisted of one lower layer of polymer with less elastic properties, containing no admixtures, and one upper layer of polymer with more elastic properties, containing plant admixtures, in the amount of 10% by weight of either goldenrod (Solidago virgaurea L.), or of turmeric (Curcuma longa L.). The admixtures S. virgaurea and C. longa were intended to introduce new biodegradable and medicinal properties without causing too much deterioration of physical or mechanical properties. Some polymer composites additionally contained magnetic particles in the form of carbonyl iron (Fe) in the amount of 20% by weight. The tests of mechanical tensile strength of the composites, water absorption, frost resistance, and surface contact angle were performed. Microscopic examinations determined the roughness of the cross-sectional surfaces. A constant magnetic field with magnetic induction B, which was an additional external factor changing the properties and structure of two-layer polymer composites, was also used in the research. Full article

Reactive oxygen species (ROS) are generated predominantly during cellular respiration and play a significant role in signaling within the cell and between cells. However, excessive accumulation of ROS can lead to cellular dysfunction, disease progression, and apoptosis that can lead to organ dysfunction. To overcome the short half-life of ROS and the relatively small amount produced, various imaging methods have been developed, using both endogenous and exogenous means to monitor ROS in disease settings. In this review, we discuss the molecular mechanisms underlying ROS production and explore the methods and materials that could be used to detect ROS overproduction, including iron-based materials, ROS-responsive chemical bond containing polymers, and ROS-responsive molecule containing biomaterials. We also discuss various imaging and imaging techniques that could be used to target and detect ROS overproduction. We discuss the ROS imaging potentials of established clinical imaging methods, such as magnetic resonance imaging (MRI), sonographic imaging, and fluorescence imaging. ROS imaging potentials of other imaging methods, such as photoacoustic imaging (PAI) and Raman imaging (RI) that are currently in preclinical stage are also discussed. Finally, this paper focuses on various diseases that are associated with ROS overproduction, and the current and the future clinical applications of ROS-targeted imaging. While the most widely used clinical condition is cardiovascular diseases, its potential extends into non-cardiovascular clinical conditions, such as neurovascular, neurodegenerative, and other ROS-associated conditions, such as cancers, skin aging, acute kidney injury, and inflammatory arthritis. Full article

Auxetic structures showcase notable properties such as high indentation resistance, shear stiffness, fracture toughness, and acoustic energy absorption. Recent advancements in additive manufacturing have facilitated the creation of complex auxetic designs, but there has been less emphasis on developing new materials. This study focuses on using recycled iron powders mixed with biodegradable polymers by using the solution casting method to create sustainable, 3D-printable materials for energy absorption applications. This research involved examining a 2D re-entrant structure, evaluating the effects of varying iron powder concentrations in the polymer. The analyses included thermogravimetric analyses, differential scanning calorimetry, and microstructural examination, alongside compression tests to assess strength and absorption capabilities. The most effective 3D-printed composite, containing 10% iron powders, demonstrated a substantial improvement in specific energy absorption (SEA of 2.051 kJ/kg compared to neat PLA with an SEA of 0.160 kJ/kg) and exhibited favorable mechanical and thermal properties. The TGA showed that adding iron powder reduced PLA’s onset degradation temperature from 340 °C to 310 °C, 295 °C, and 270 °C for 5%, 10%, and 15% iron, respectively, confirming iron’s catalytic effect on PLA degradation. The DSC analysis showed that adding iron powder increased the degree of crystallinity from 5.63% for pure PLA to 5.77%, 6.79%, and 6.91% for 5%, 10%, and 15% iron, respectively, indicating iron’s role as a nucleation agent. These results highlight the potential of novel iron/PLA 2D re-entrant composites for energy-absorbent applications, emphasizing sustainability and cost-effectiveness. Full article

Hybrid nanocomposites combining biopolymer fibers incorporated with nanoparticles (NPs) have received increasing attention due to their remarkable characteristics. Inorganic NPs are typically chosen for their properties, such as magnetism and thermal or electrical conductivity, for example. Meanwhile, the biopolymer fiber component is a backbone, and could act as a support structure for the NPs. This shift towards biopolymers over traditional synthetic polymers is motivated by their sustainability, compatibility with biological systems, non-toxic nature, and natural decomposition. This study employed the solution blow spinning (SBS) method to obtain a nanocomposite comprising poly(vinyl pyrrolidone), PVA, and gelatin biodegradable polymer fibers incorporated with magnetic iron oxide nanoparticles coated with poly(acrylic acid), PAA_2k, coded as γ-Fe₂O₃-NPs-PAA_2k. The fiber production process entailed a preliminary investigation to determine suitable solvents, polymer concentrations, and spinning parameters. γ-Fe₂O₃-NPs were synthesized via chemical co-precipitation as maghemite and coated with PAA_2k through the precipitation–redispersion protocol in order to prepare γ-Fe₂O₃-NPs-PAA_2k. Biopolymeric fibers containing coated NPs with sub-micrometer diameters were obtained, with NP concentrations ranging from 1.0 to 1.7% wt. The synthesized NPs underwent characterization via dynamic light scattering, zeta potential analysis, and infrared spectroscopy, while the biopolymer fibers were characterized through scanning electron microscopy, infrared spectroscopy, and thermogravimetric analysis. Overall, this study demonstrates the successful implementation of SBS for producing biopolymeric fibers incorporating iron oxide NPs, where the amalgamation of materials demonstrated superior thermal behavior to the plain polymers. The thorough characterization of the NPs and fibers provided valuable insights into their properties, paving the way for their potential applications in various fields such as biomedical engineering, environmental remediation, and functional materials. Full article

The mining and steelmaking industries, while vital for economic and social development, produce and dispose of waste that contributes to environmental instability and discomfort. In this context, this study aimed to develop novel polymer composites intended for Artificial Ornamental Stone (AOS) application by incorporating iron ore tailings (IOTs), quartzite waste (QTZ), and steel slag (SS) into an epoxy (EP) matrix. The chemical, mineralogical, physical, mechanical, morphological, and thermal properties of the materials were assessed. Three waste mixtures were proposed using the Modified Andreassen Curve method, each with 35, 45, and 55 v/v% of EP. The composite properties were evaluated, showing that the composite with QTZ, SS, and 55 v/v% EP exhibited the lowest porosity (0.3%), water absorption (0.1%), and highest flexural strength (41 MPa). The composite containing the three wastes with 55 v/v% EP presented 1.0% porosity, 0.4% water absorption, and 34 MPa flexural strength. Lastly, the composite with IOTs, QTZ, and 55 v/v% EP exhibited 1.1% apparent porosity, 0.5% water absorption, and 23 MPa flexural strength. Therefore, the polymer composites developed with IOTs, QTZ, SS, and EP demonstrated suitable properties for wall cladding and countertops, presenting a potentially sustainable alternative to reduce environmental impacts from the mining and steelmaking industries. Full article

A wastewater treatment plant (WWTP) prototype coupled with Moringa oleifera seeds (MOSs) was developed to evaluate its effectiveness to reduce metallic trace elements (MTEs) in domestic wastewater. The WWTP is composed of a septic tank (F0) where wastewater is treated by biological processes under anaerobic conditions, followed by a bacterial filter (F1) where wastewater is filtered under aerobic conditions, followed by an infiltration well (F2), which provides additional filtration of wastewater before discharge into the soil. MTEs present in waters can bind with humic substances contained in colloid particles and then be eliminated by coagulation–flocculation with a cationic polyelectrolyte. MOSs contain positively charged cationic polymers that can neutralize the colloids contained in waters, which are negatively charged. Based on this observation, 300 mg·L⁻¹ of MOS was added into F0, 50 mg·L⁻¹ into F1, and 50 mg·L⁻¹ into F2 mg·L⁻¹. MOS activation in samples was performed by stirring rapidly for 1.5 min, followed by 5 min of gentle stirring and 3 h of settling. The data analysis shows that wastewater samples had significant concentrations of MTEs, particularly for Cu, Ni, Sr, and Ti, and sediment samples had high amounts of Cr, Cu, Ni, Sr, Ti, and V. The addition of MOS to F0, F1, and F2 samples resulted in reductions in MTE concentration of up to 36%, 71%, 71%, 29%, 93%, 81%, 13%, 52%, and 67% for Co, Cr, Cu, Ni, Pb, Se, Sr, Ti, and V, respectively. The quantified MTEs (As, Co, Cr, Cu, Ni, Pb, Se and V) in treated samples were reported to be lower than UN-EP standards for a safe reuse for irrigation and MOS proved to be as effective as chemical coagulants such as lime and ferric iron for the removal of MTEs contained in wastewater. These results highlight the potential of MOSs as natural coagulants for reducing MTE content in domestic wastewater. This study could be the first to evaluate the effectiveness of MOS in reducing 10 MTEs, including As, Co, Se, Sr, Ti, and V, which are currently understudied. It could also provide a better understanding of the origin of MTEs found in domestic wastewaters and how an effective treatment process can result in high-quality treated wastewaters that can be reused for irrigation without posing health or environmental risks. However, more research on MOSs is needed to determine the type and composition of the coagulant substance found in the seeds, as well as the many mechanisms involved in the decrease in MTEs by MOSs, which is currently understudied. A better understanding of MOS structure is required to determine the optimum alternative for ensuring the optimal effect of MOS paired with WWTP in removing MTEs from domestic wastewaters. Full article

In the pursuit of fabricating functional ceramic nanostructures, the design of preceramic functional polymers has garnered significant interest. With their easily adaptable chemical composition, molecular structure, and processing versatility, these polymers hold immense potential in this field. Our study succeeded in focusing on synthesizing ferrocene-containing block copolymers (BCPs) based on polyacrylonitrile (PAN). The synthesis is accomplished via different poly(acrylonitrile-block-methacrylate)s via atom transfer radical polymerization (ATRP) and activators regenerated by electron transfer ATRP (ARGET ATRP) for the PAN macroinitiators. The molecular weights of the BCPs range from 44 to 82 kDa with dispersities between 1.19 and 1.5 as determined by SEC measurements. The volume fraction of the PMMA block ranges from 0.16 to 0.75 as determined by NMR. The post-modification of the BCPs using 3-ferrocenyl propylamine has led to the creation of redox-responsive preceramic polymers. The thermal stabilization of the polymer film has resulted in stabilized morphologies based on the oxidative PAN chemistry. The final pyrolysis of the sacrificial block segment and conversion of the metallopolymer has led to the formation of a porous carbon network with an iron oxide functionalized surface, investigated by scanning electron microscopy (SEM), energy dispersive X-ray mapping (EDX), and powder X-ray diffraction (PXRD). These findings could have significant implications in various applications, demonstrating the practical value of our research in convenient ceramic material design. Full article

Iron plays a critical role in lung infections due to its function in the inflammatory immune response but also as an important factor for bacterial growth. Iron chelation represents a potential therapeutic approach to inhibit bacterial growth and pathologically increased pro-inflammatory mediator production. The present study was designed to investigate the impact of the iron chelator DIBI in murine lung infection induced by intratracheal Pseudomonas aeruginosa (strain PA14) administration. DIBI is a polymer with a polyvinylpyrrolidone backbone containing nine 3-hydroxy-1-(methacrylamidoethyl)-2-methyl-4(1H) pyridinone (MAHMP) residues per molecule and was given by intraperitoneal injection either as a single dose (80 mg/kg) immediately after PA14 administration or a double dose (second dose 4 h after PA14 administration). The results showed that lung NF-κBp65 levels, as well as levels of various inflammatory cytokines (TNFα, IL-1β, IL-6) both in lung tissue and bronchoalveolar lavage fluid (BALF), were significantly increased 24 h after PA14 administration. Single-dose DIBI did not affect the bacterial load or inflammatory response in the lungs or BALF. However, two doses of DIBI significantly decreased bacterial load, attenuated NF-κBp65 upregulation, reduced inflammatory cytokines production, and relieved lung tissue damage. Our findings support the conclusion that the iron chelator, DIBI, can reduce lung injury induced by P. aeruginosa, via its anti-bacterial and anti-inflammatory effects. Full article

Sulfate-reducing bacteria (SRB) are the primary cause of corrosion in oil and gas pipeline steel. To understand how temperature and immersion time affect the SRB-induced corrosion of BG L450OQO-RCB pipe steel, the present study delved into the morphology and elemental composition of corrosion products, corrosion rate, corrosion solution composition, and electrochemical performance at different temperatures (25, 40, and 60 °C) and immersion times (5, 10, and 20 days). During the SRB corrosion of the investigated steel, extracellular polymeric substances (EPSs), iron sulfide, and iron phosphide were produced on the surfaces of the steel samples, along with the calcium carbonate product. Chloride ions in the corrosion solution contributed to the corrosion of steel and the formation of chlorides on steel surfaces. Over time, the quantities of EPSs, iron sulfide, and iron phosphide gradually decreased with immersion time. The presence of surface iron chloride initially increased and then decreased with immersion time. Conversely, the presence of calcium carbonate surface product initially decreased and then increased with immersion time. The content of SRB extracellular polymer, iron sulfide, and iron phosphide changed imperceptibly between 25 and 40 °C, but the overall content decreased at 60 °C. The content of surface ferric chloride remained practically unchanged between 25 and 40 °C but increased at 60 °C. The calcium carbonate surface product increased slightly with higher temperature. The corrosion of Cu-containing steel by SRB follows the cathodic depolarization theory. Full article