Search Results (45)

The 2020 southern Puerto Rico earthquake sequence highlighted the severe seismic vulnerability of informally constructed two-story reinforced concrete (RC) houses. This study examines the failure mechanisms of these structures and assesses the effectiveness of first-floor RC shear-wall retrofitting. Nonlinear pushover and dynamic time–history analyses were performed using fiber-based distributed plasticity models for RC frames and nonlinear macro-elements for second-floor masonry infills, which introduced a significant inter-story stiffness imbalance. A bi-directional seismic input was applied using spectrally matched, near-fault pulse-like ground motions. The findings for the as-built structures showed that stiffness mismatches between stories, along with substantial strength and stiffness differences between orthogonal axes, resulted in concentrated plastic deformations and displacement-driven failures in the first story—consistent with damage observed during the 2020 earthquakes. Retrofitting the first floor with RC shear walls notably improved the performance, doubling the lateral load capacity and enhancing the overall stiffness. However, the retrofitted structures still exhibited a concentration of inelastic action—albeit with lower demands—shifted to the second floor, indicating potential for further optimization. Full article

On 22 May 2012, a magnitude Mw 5.6 earthquake struck the Pernik region of western Bulgaria, causing structural damage in nearby cities, including Sofia. This study assesses the seismic response of a six-story reinforced concrete building in central Sofia, utilizing real accelerogram data recorded at the basement (SGL1) and sixth floor (SGL2) levels during the earthquake. Using the Kanai–Yoshizawa (KY) model, the study estimates inter-story motion and assesses amplification effects across the structure. Analysis of peak ground acceleration (PGA), velocity (PGV), displacement (PGD), and spectral ratios reveals significant dynamic amplification of peak ground acceleration and displacement on the sixth floor, indicating flexible and dynamic behavior, as well as potential resonance effects. The analysis combines three spectral techniques—Horizontal-to-Vertical Spectral Ratio (H/V), Floor Spectral Ratio (FSR), and the Random Decrement Method (RDM)—to determine the building’s dynamic characteristics, including natural frequency and damping ratio. The results indicate a dominant vibration frequency of approximately 2.2 Hz and damping ratios ranging from 3.6% to 6.5%, which is consistent with the typical damping ratios of mid-rise concrete buildings. The findings underscore the significance of soil–structure interaction (SSI), particularly in sedimentary basins like the Sofia Graben, where localized geological effects influence seismic amplification. By integrating accelerometric data with advanced spectral techniques, this research can enhance ongoing site-specific monitoring and seismic design practices, contributing to the refinement of earthquake engineering methodologies for mitigating seismic risk in earthquake-prone urban areas. Full article

Engineered laminated bamboo frame structures have seen notable advancements in China, driven by their potential in sustainable construction. However, accurately predicting their seismic performance remains a pivotal challenge. Structural and non-structural damage caused by earthquakes can severely compromise building operability, lead to substantial economic losses, and disrupt safe evacuation processes, collectively exacerbating disaster impacts. To address this, three laminated bamboo frame models (3-, 4-, and 5-story) were developed, integrating energy-dissipating T-shaped steel plate beam–column connections. Two engineering demand parameters—peak inter-story drift ratio (PIDR) and peak floor acceleration (PFA)—were selected to quantify seismic responses under near-field and far-field ground motions. The study systematically evaluates suitable intensity measures for these parameters, emphasizing efficiency and sufficiency criteria. Regarding efficiency, the applicable intensity measures for PFA differ from those for PIDR. The measures for PFA tend to focus more on acceleration amplitude-related measures such as peak ground accelerations (PGA), sustained maximum acceleration (SMA), effective design acceleration (EDA), and A₉₅ (the acceleration at 95% Arias intensity), while the measures for PIDR are primarily based on spectral acceleration-related measures such as S_a(T₁) (spectral acceleration at fundamental period), etc. Concerning sufficiency, significant differences exist in the applicable measures for PFA and PIDR, and they are greatly influenced by ground motion characteristics. Full article

Multi-floored grain warehouses are widely used in China due to their efficient space utilization and high storage capacity. This study evaluates the seismic performance of such structures using a Composite Structure of Steel and Concrete (CSSC) system under various grain-loading conditions. A finite element model was developed in OpenSees based on actual loading scenarios, with both pushover and time history analyses conducted. Results show that the EEF condition (E = Empty, F = Full; top–middle–bottom = Empty–Empty–Full) leads to a 35.14% increase in peak base shear compared to the FEE condition (grain on the top floor only). Capacity spectrum analysis indicates that EEF provides higher initial stiffness and lower displacement across all performance points. Time history results reveal that configurations with lighter upper mass (EFF, EEE) are more prone to top-floor acceleration amplification, while FFF and FFE demonstrate more stable responses due to balanced mass distribution. The maximum inter-story drift consistently occurs at the second floor, with FFF and FFE showing the most significant deformation. All drift ratios meet code limits, confirming the safety and applicability of the CSSC system under various storage scenarios. Full article

The eccentrically braced frame (EBF) is a typical structural system used in high-rise buildings. Current related design methods focus on the concrete and steel structures rather than on the complex composite structure. In addition, they tend to overlook the contribution of the energy-dissipation unit and its corresponding additional influence on the structure. In this study, a precast composite EBF structure is selected as a case study, including the partially steel-reinforced concrete (PSRC) beam and the concrete-filled steel tubular (CFST) column. A modified energy-based design method is proposed to leverage the excellent seismic performance of the precast composite EBF structure. The multi-stage energy-dissipation mechanism and the additional influence of the eccentric braces are systematically considered through the energy distribution coefficient and the layout of dampers. A case study of a 12-floor, three-bay precast composite EBF structure is conducted using a series of nonlinear time-history analyses. Critical seismic responses, including the maximum inter-story drift ratio, residual inter-story drift ratio, and peak acceleration, are systematically analyzed to evaluate the effectiveness of the proposed design theory. The distribution coefficient is recommended to range from 0.70 to 0.80 to balance the energy-dissipation contribution between the frame and the eccentric braces. In terms of the damper layout, the energy-dissipation contribution of the eccentric brace should differ among the lower, middle, and upper floors. Full article

In the whole service life of building clusters, they will encounter multiple hazards, including the disaster chain of earthquakes and building debris. The falling debris may block the post-earthquake roads and even severely affect the evacuation, emergency, and recovery operations. It is of great significance to develop a surrogate model for predicting seismic responses of building clusters as well as a prediction model of post-earthquake debris. This paper presents a general methodology for developing a surrogate model for rapid seismic responses calculation of building clusters and probabilistic prediction model of debris width. Firstly, the building cluster is divided into several types of representative buildings according to the building function. Secondly, the finite element (FE) method and discrete element (DE) method are, respectively, used to generate the data pool of structural floor responses and debris width. Finally, with the structural response data of maximum floor displacement, a surrogate model for rapidly calculating seismic responses of structures is developed based on the XGBoost algorithm, achieving R² > 0.99 for floor displacements and R² = 0.989 for maximum inter-story drift ratio (MIDR) predictions. In addition, an unbiased probabilistic prediction model for debris width of blockage is established with Bayesian updating rule, reducing the standard deviation of model error by 60% (from σ = 10.2 to σ = 4.1). The presented models are applied to evaluate the seismic damage of the campus building complex in China University of Mining and Technology, and then to estimate the range of post-earthquake falling debris. The results indicate that the surrogate model reduces computational time by over 90% compared to traditional nonlinear time-history analysis. The application in this paper is helpful for the development of disaster prevention and mitigation policies as well as the post-earthquake rescue and evacuation strategies for urban building complexes. Full article

High-rise building structures with podiums are widely present, and establishing a fast numerical prediction method to evaluate their wind-induced response characteristics is of great significance for engineering applications. This article proposes a process algorithm based on the AR (autoregression) method to solve the time history of fluctuating wind speed and determine fluctuating wind load. The simulated fluctuating wind speed spectrum obtained through this algorithm matches the target wind speed spectrum, and the wind-induced response characteristics of high-rise buildings with podiums were studied using MIDAS GEN (2021) structural analysis software. In order to evaluate the influence of different parameters on the wind-induced vibration response of high-rise buildings with podiums, a total of 11 comparative conditions were set, including the presence or absence of podiums, podium height, podium area, and podium layout conditions. A comprehensive time history analysis was conducted on the displacement, acceleration, shear force, and overturning moment of the wind-induced vibration response of high-rise buildings with podiums. The results indicate that in high-rise buildings with podiums, adding podiums and increasing their height and area can help suppress the inter-story displacement of the main building and the inter-story acceleration, inter-story shear force, and intra-story overturning moment of the middle and lower floors, which is beneficial for the safety and stability of the high-rise building structure. The layout of the podium has an impact on the wind-induced vibration response of the main building. When the podium and main building are symmetrically arranged in the downwind direction, the maximum displacement of each floor is small, while the maximum displacement curve of buildings with asymmetric layout at the junction of the podium and main building is not smooth. The design of the central layout of the podium and main building can effectively reduce the maximum shear force and maximum overturning moment of the higher floors of the building, but the effect is opposite at lower floors. Full article

The objective of this study was to examine the seismic behavior of steel buildings equipped with linear and nonlinear viscous dampers that may exhibit variable capacity. More specifically, nonlinear time history analyses were conducted on two three-dimensional steel buildings utilizing a number of recorded seismic motions. Initially, it was assumed that the distribution of viscous dampers was uniform along the height of the building and, thus, the damping coefficients used to size the viscous dampers were derived. Subsequently, nonlinear time history analyses were performed assuming either linear or nonlinear viscous dampers, which may operate at 80%, 100%, and 120% of their capacity. The response parameters extracted by these analyses included the base shear (structural and inertial), the inter-story drift ratio (IDR), the residual inter-story drift ratio (RIDR), the absolute floor accelerations, the formation of plastic hinges, and the forces experienced by the dampers. On the basis of these response parameters, the most appropriate type of viscous dampers was indicated. Full article

This paper introduces a new self-locking-unlockable modular building with an inter-module connection, and its seismic performance is investigated. The new connection can realize fast connection and unlocking during construction through exceptional design. In this paper, taking the Tianjin Binhai Apartment project as the background, for the actual force situation of the new connection, considering the influence of corrugated steel plate stiffness, a simplified model of the connection is constructed by using multi-fold elastic connection, and the corrugated steel plate stiffness is simulated with equivalent support. In the MIDAS Gen 2021 software, the five-story and six-story structural models using traditional rigid connections and new connections were established, respectively, and reaction spectrum analysis was carried out. Meanwhile, seismic waves that comply with codes were selected for dynamic time course analysis. The results show that the stress ratios of all components of the new connection model and the traditional rigid model are less than 1. Among them, the maximum stress ratios of both floor beams are 0.745 and 0.725, respectively; the maximum stress ratios of the modular columns are 0.655 and 0.494, respectively; the stress ratios of the ceiling beams are all less than 0.5; and the two models show good strength and stiffness reserves, following the design principle of strong columns and weak beams and verifying the reliability of the new connection model. Meanwhile, it is found that the inter-story displacement angle of the six-story structure with the new connections is less than the normative value under the action of rare earthquakes, and the difference in top displacement is about 18% compared with that of the rigid structure, so it is suggested that the new connections can be applied within the height of six stories. Full article

This paper focuses on the theoretical and analytical modeling of a novel seismic isolator termed the Passive Friction Mechanical Metamaterial Seismic Isolator (PFSMBI) system, which is designed for seismic hazard mitigation in multi-story buildings. The PFSMBI system consists of a lattice structure composed of a series of identical small cells interconnected by layers made of viscoelastic materials. The main function of the lattice is to shift the fundamental natural frequency of the building away from the dominant frequency of earthquake excitations by creating low-frequency bandgaps (FBGs) below 20 Hz. In this configuration, each unit cell contains an inner resonator that slides over a friction surface while it is tuned to vibrate at the fundamental natural frequency of the building. This resonance enhances the energy dissipation capacity of the PFSMBI system. After deriving the governing equations for four selected lattice configurations (i.e., Cases 1–4), a parametric study is performed to optimize the PFSMBI system for a wide range of harmonic ground motion frequencies. In this study, we examine how key parameters, such as the mass ratios of the cells and resonators, tuning frequency ratios, the number of cells, and the coefficient of friction, affect the system’s performance. The PFSMBI system is then incorporated into the dynamic model of a six-story base-isolated building to evaluate its effectiveness in reducing the floor acceleration and inter-story drift under actual earthquake ground motion records. This dynamic model is used to investigate the effect of stick–slip motion (SSM) on the energy dissipation performance of a PFSMBI system by employing the LuGre friction model. The numerical results show that the optimized PFSMBI system, through its lattice structure and frictional resonators, effectively reduces floor acceleration and inter-story drift by leveraging FBGs and frictional energy dissipation, particularly when SSM effects are properly accounted for. Finally, a small-scale prototype of the PFSMBI system with two cells is developed to verify the effect of SSM. This experimental validation highlights that neglecting SSM can lead to an overestimation of the energy dissipation performance of PFSMBI systems. Full article

This study investigates the seismic performance of two-, four-, and six-story composite buildings equipped with viscous wall dampers, focusing on structures with concrete-filled steel tubular (CFST) columns and steel beams. Through nonlinear time history analyses using sequential ground motions, the research evaluates the effectiveness of viscous wall dampers in mitigating seismic demands. Results demonstrate significant reductions in both interstory drift ratios and peak floor accelerations across all building heights when dampers are installed. The study particularly highlights the dampers’ effectiveness in controlling drift demands in lower and middle floors while managing acceleration amplification at upper levels. The findings validate the integration of viscous wall dampers into mid-rise composite structures and underscore the importance of considering sequential ground motions in seismic performance evaluations. Full article

In this work, the seismic response of a multi-story, multi-bay special truss moment frame (STMF) with Ni-Ti shape memory alloys (SMAs) incorporated in the form of X-diagonal braces in the special segment is investigated. The diameter of the SMAs per diagonal in each floor was initially determined, considering the expected ultimate strength of the special segment, developed when the frame reaches its target drift and the desirable collapse mechanism, i.e., the formation of plastic hinges, according to the performance-based plastic design procedure. To further investigate the response of the structure with the SMAs incorporated, half the calculated SMA diameters were introduced. Continuing, three more cases were investigated: the mean value of the SMA diameter was introduced at each floor (case DC1), half the SMA diameter of case DC1 (case DC2), and twice the SMA diameter of case DC1 (case CD3). Dynamic time history analyses under seven benchmark earthquakes were conducted using commercial nonlinear Finite Element software (SeismoStruct 2024). Results were presented in the form of top-displacement time histories, the SMAs force–displacement curves, and maximum inter-story drifts, calculating also maximum SMA displacements. The analysis outcomes highlight the potential of the SMAs to be considered as a novel material in the seismic retrofit of steel structures. Both design approaches presented exhibit a certain amount of effectiveness, depending on the distribution, with the placement of the SMA bars and the seismic excitation considered. Further research is suggested to fully understand the capabilities of the use of SMAs as dissipation devices in steel structures. Full article

Timber–concrete hybrid structures are commonly employed in multi-story timber buildings; however, further research is necessary to fully understand the seismic performance of these structures as well as the dynamic properties of the floor. The two dynamic concerns, seismic effects and the vibration of floors in hybrid structures, are key issues, in view of which this study aimed to investigate the small-seismic-response spectra and elastic time histories in a high-rise timber hybrid building, specifically the medical technology building of Jiangsu Provincial Rehabilitation Hospital in China. The dynamic characteristics of a localized cross-laminated timber (CLT) floor were tested in situ, and the impacts of human-induced vibration were quantified. Comprehensive theoretical analysis results reveal that the basic vibration pattern of the structure was mainly translational in nature and that the period ratio, inter-story displacement angle, and shear-to-weight ratio all met the demands of the Chinese timber building design code. The experimental test results show that the vertical natural frequency of the CLT floor was about 15.96 Hz and thus met appropriate requirements with respect to natural frequency. However, peak floor acceleration was found to be high under the conditions of a single person walking quickly, a single person trotting, and multiple persons walking randomly. In light of these findings, the floor should be paved with a fine-grained concrete building surface, according to design requirements, so that its serviceability might be improved. Overall, the relevant analytical methods presented in this paper provide guidance and practical reference for the seismic analysis of timber hybrid structures, as well as vibration serviceability analysis for CLT floors. Full article

Seismic isolation technology plays a crucial role in enhancing earthquake resistance and mitigating disasters for building structures. In this study, the ETABS analysis software V21.0.1 is utilized to establish a numerical model of a six-story steel reinforced concrete frame structure. Both the time-history analysis method and response spectrum method are employed to calculate the seismic response of the model under earthquake actions. The placement of an isolation layer on the foundation and from the first to fifth floor is considered, with separate calculations conducted for each scenario. Subsequently, a comprehensive comparison and analysis of the dynamic response characteristics among different design schemes are performed. The results demonstrate that the most favorable isolation effect is achieved when the isolation layer is implemented on the foundation or first floor. Compared to non-isolated structures, the natural period of the structure can be extended by 2.2 times and 2 times under the base isolation and first-floor top isolation schemes, respectively. The damping coefficients can reach 0.35 and 0.36, respectively, while the inter-story drift angles can be reduced by 66% and 67%, respectively. Full article

To achieve rapid post-earthquake repair of self-centering ribbed floor flat-beam frame structures, a ductile hybrid joint consisting of dog-bone-shaped, weakened, energy-dissipating steel bars connected to the upper and lower column sections through high-strength threads is proposed based on the damage control design concept. By moving the ductile energy-dissipating zone out to the locally weakened section of the energy-dissipating steel bars and the locally unbonded prestressed steel bars in the core area, the residual deformation was limited and the seismic performance improved. Based on the working principle of hybrid joints, low cycle loading tests were conducted on two joint specimens to analyze the influence of lateral prestress on the seismic performance of the hybrid joints. Numerical modeling methods were used to compare the position of the energy-dissipating steel bars in the composite layer and the friction performance of the joints. The research results indicated that the hybrid joint had stable load bearing, deformation, and energy dissipation capabilities, with damage being primarily concentrated in the energy-dissipating steel bars. Even at an inter-story displacement angle of 5.5%, the upper and lower column segments remained elastic. After unloading, the connection seam at the joint was closed, and the self-centering performance was good. When the inter-story displacement angle reached 5.5%, the lateral prestress increased from 150 kN to 250 kN, the ultimate bearing capacity of the joint increased by 16.3%, and the cumulative energy consumption increased by 30.0%. The influence of the friction coefficient of the joint surface on the structural performance was set at a threshold of 0.7. When it was less than the threshold, the ultimate bearing capacity and initial stiffness of the joint increased with the increase in the friction coefficient. After reaching the threshold, the increase in the ultimate bearing capacity of the joint slowed down, and the rate of stiffness degradation gradually accelerated. This joint showed excellent seismic performance and can thus achieve post-earthquake repair of structures. Full article