Search Results (96)

Dental implant components are typically fabricated using subtractive manufacturing, often involving metal materials that can be costly, inefficient, and time-consuming. This study explores the use of additive manufacturing (AM) with zirconia for dental implant overdenture bars, focusing on mechanical performance, stress distribution, and fit. Solid and lattice-structured bars were designed in Fusion 360 and produced using LithaCon 210 3Y-TZP zirconia (Lithoz GmbH, Vienna, Austria) on a CeraFab 8500 printer. Post-processing included cleaning, debinding, and sintering. A 3D-printed denture was also fabricated to evaluate fit. Thermography and optical imaging were used to assess adaptation. Custom fixtures were developed for flexural testing, and fracture loads were recorded to calculate stress distribution using finite element analysis (ANSYS R2025). The FEA model assumed isotropic, homogeneous, linear-elastic material behavior. Bars were torqued to 15 Ncm on implant analogs. The average fracture loads were 1.2240 kN (solid, n = 12) and 1.1132 kN (lattice, n = 5), with corresponding stress values of 147 MPa and 143 MPa, respectively. No statistically significant difference was observed (p = 0.578; α = 0.05). The fracture occurred near high-stress regions at fixture support points. All bars demonstrated a clinically acceptable fit on the model; however, further validation and clinical evaluation are still needed. Additively manufactured zirconia bars, including lattice structures, show promise as alternatives to conventional superstructures, potentially offering reduced material use and faster production without compromising mechanical performance. Full article

Purpose: The aim of this study was to evaluate the long-term clinical results of two different implant–abutment connection types (screw-retained/Morse locking taper), marginal bone loss, and complications in prosthetic restorations. Materials and Methods: In 2017–2018, 579 implants and 242 implant-supported restorations applied to 137 patients were included in the study. Patients were recalled every six months, clinical evaluations were accomplished, and complications were recorded. When examining the distribution of prosthetic restorations by type, it was determined that 38 (15.70%) were single crowns, 136 (56.19%) were fixed partial cement-retained bridge restorations, 53 (21.90%) were fixed partial screw-retained bridge restorations, and 15 (6.19%) were overdenture prostheses. Findings: Overall, complications included eighteen (21.68%) retention losses, nineteen (22.89%) instances of screw loosening, twenty-one (25.30%) veneer ceramic fractures, three (3.61%) acrylic base fractures, fourteen (16.87%) cases of peri-implantitis, and eight (9.64%) implant losses. Conclusions: Differences in complication rates were observed between implants with different implant–abutment connection designs. While no significant differences were found regarding annual mesial and distal marginal bone loss for implants with conical locking connections, a significant difference was detected in those with screw-retained connections. In both implant groups, mesial and distal marginal bone loss progressed gradually over the follow-up period. Full article

Background: A considerable percentage of people in the population have lost their teeth. According to the Word Health Organization (WHO), 40% have lost teeth for multiple reasons. The lack of restorative treatments and the lack of fixed options could impact the quality of life of patients. Objective: To determine the quality of life of patients treated with dental implants at the School of Dentistry, University of the Americas, Quito, Ecuador, by the Medical Specialty in Oral Rehabilitation from 2017–2022. Materials: The inclusion criterion was patients treated with dental implants age 20 to 70 years old, who agreed to participate in this study, in Quito/Ecuador. The Oral Health Impact Profile (OHIP-14) survey was used. The patients’ clinical history, psychological status, and social status were also recorded. Complementary tests (clinic analysis) were conducted to evaluate the general health status of each patient. Results: After the corresponding analysis, the total number of patients who wished to participate in this study in compliance with the inclusion criteria was n = 1303. The seven questions included patient sex, age, and type of prosthesis used in their rehabilitation (single implant, fixed prosthesis on an implant, overdentures, or hybrid prostheses). The obtained results indicated that single implants and overdentures (two jaw implants) improved quality of life, and no statistically significant difference was noted between the sexes. Conclusions: The quality of life of patients with total dentures who received dental implants improved substantially, and more fixed dentures helped them to recover their masticatory function appropriately. Single implants were not excluded. In the investigated population, the results were unanimous in how implants improved their comfort and even helped in the recovery of their self-esteem. Full article

Introduction: Generally, after an oral oncological therapeutic process in which, unfortunately, surgery plays a fundamental role, a reconstructive and rehabilitative procedure should be initiated, seeking as far as possible to recover the patient’s vital functions (mastication, aesthetics, and phonetics). Case report: We present the case of a patient who successfully underwent treatment for mandibular sarcoma. After a disease-free period of one year, following oncological treatment, an intervention was performed for the insertion of dental implants into the fibula to subsequently rehabilitate the patient prosthetically. There were several challenges, including free-end edentulous space in the lower jaw with a depth of 18 mm on peri-implant tissues consisting of osteoseptocutaneous skin graft, hypotonic perioral musculature, and high aesthetic expectations of the patient. An overdenture with a titanium milled bar substructure with retentive prosthetic components was chosen for treatment. This implant-supported removable prosthesis was selected to facilitate cleaning, since the patient did not maintain oral hygiene habits. The patient was educated on using and handling the prosthesis, and the treatment objectives were achieved (to restore aesthetics and masticatory function). Conclusions: Removable prostheses are a valid alternative for oncologic patients and patients with unfavorable conditions for more complex implant-supported rehabilitation. Full article

Sandblasting and acid etching are common procedures used to treat implant surfaces, enhancing osseointegration and improving clinical success rates. This clinical study aimed to evaluate the long-term outcomes of sandblasted and acid-etched implants. A total of 303 implants were placed in 114 partially and totally edentulous patients using a two-stage surgical technique and an early loading protocol (6–8 weeks). Clinical findings for implants and prosthetics were evaluated over a 12-year follow-up period. A total of 12 implants (3.9%) failed, with 3 failures occurring during the healing period before loading and 9 due to peri-implantitis. The cumulative survival rate for all implants was 96.1%. A total of 156 prostheses were placed on 300 implants, 87 single crowns, 45 partial fixed bridges, 9 full-arch fixed restorations, and 15 overdentures. The mean marginal bone loss was 1.18 mm. (SD. 0.64 mm.). Thirty-nine implants (13%) in twenty-four patients exhibited peri-implantitis. Technical complications, including prosthetic screw loosening or fracture, ceramic chipping, and acrylic fractures, were observed in 24 subjects (21.1%). Sandblasted and acid-etched surface implants placed in the maxilla and mandible reported favorable outcomes and stable tissue conditions with an early loading protocol. Full article

Background: Mini dental implants (MDIs) are alternatives to support an overdenture when a standard diameter implant cannot be placed due to lack of bone volume. They reduce the need for invasive bone grafting and lower the barrier for treatment. Aim: This prospective study reports on implant and patient-centered outcomes of flaplessly placed, early loaded MDIs supporting horseshoe-shaped maxillary overdentures after 7 years of function. Materials and Methods: Patients with a CBCT-confirmed thin alveolar crest received 5–6 one-piece MDIs using mentally guided flapless surgery. The conventional denture was relined and MDIs were provisionally loaded within one week. After 6 months the non-splinted MDIs were actively loaded with a horseshoe overdenture. Implant and prosthetic survival, peri-implant health (PPD and BoP) and patient-related outcomes using OHIP-14 and Subjective Masticatory Evaluation were assessed after 7 years. Results: 185 MDIs were placed in 14 females and 17 males. During provisional loading, 32 MDIs were lost, and 17 replacements were required in 16 patients. In total, 170 out of 202 totally placed MDIs were supporting 29 overdentures after 6 months. Cumulative implant failure increased from 15.8% at the moment of active loading to 34.7% at 7 years. After 7 years, 76% of the initially placed overdentures remained functional, mean PPD was 3.48 (SD 0.86), BoP was 0.20 (SD 0.40) and peri-implantitis incidence was 0.9%. The total OHIP-14 was reduced from 21.3/56 (SD: 13.1) preoperatively to 15.6/56 (SD 12.8) at provisional loading (p > 0.1) and 7.3/56 (SD 6.7) at final loading (p = 0.006), and it remained unchanged up to 7 years at 6.57/56 (SD: 8.92) (p > 0.5). Conclusions: Maxillary MDIs provide an acceptable treatment option in patients with deficient bone volume that cannot or refuse to be treated with bone grafting. Despite one third of the MDIs being lost, remaining MDIs had good peri-implant health, prosthetic success was 71% and Oral Health Related Quality of Life was beyond expectations. Full article

Background and Objectives: This research describes the management of mandibular fractures in edentulous patients with atrophic mandibles and implant-retained overdentures, exploring etiologies and treatment options. Materials and Methods: A retrospective study (January 2010–December 2023) was conducted on six patients from two hospitals (Hospital Gregorio Marañón y Hospital La Paz, Madrid). The data collected included fracture etiology, treatment type, and complications. Results: All six patients were women, with a mean age of 76.33 years. The most common cause of fracture was peri-implantitis (50%). Surgical treatment (open reduction and internal fixation) was performed in five patients, with different surgical approaches and fixation methods. One patient, due to multiple comorbidities, received conservative treatment. Complications occurred in 50% of cases, including delayed healing and hypoesthesia. The average hospital stay was four days, with a mean follow-up of 34 months. Conclusions: Mandibular fractures in these patients are rare. Surgical treatment using rigid fixation plates is recommended. The rational use of bone grafting should be taken into account. Treatment depends on fracture type, patient condition, and surgeon experience. Full article

This clinical report details the prosthetic rehabilitation of a patient following maxillary ablation to remove a peripheral giant cell granuloma. After a hemimaxillectomy, the defect was reconstructed with a fasciocutaneous radial free flap. Implant placement was digitally planned using the dual scanning technique, and implants were inserted with the aid of an acrylic surgical guide. After implant osseointegration, a removable implant-supported overdenture with an electroplated secondary structure retained on a titanium bar was fabricated. At the 3-year follow-up, peri-implant tissues remained healthy, showing only mild gingival hyperplasia around the bar, while no prosthesis retention loss or significant technical complications were observed. In conclusion, the reconstruction of the moderate maxillary defect using a soft-tissue flap provided satisfactory functional and esthetic outcomes, significantly enhancing patient satisfaction. However, the limited bone availability necessitated precise implant planning to ensure adequate biomechanical support for the overdenture. Full article

Clinical indications for the Ti-Zr alloy (Roxolid^®) mini-implants (MDIs) in subjects with narrow ridges are still under review. The aim was to analyze peri-implant and posterior edentulous area strains dependent on the MDI number, splinting status, loading force, and loading position. Six models were digitally designed and printed. Two, three, or four Ti-Zr MDIs, splinted with a bar or unsplinted (single units), supported mandibular overdentures (ODs), loaded with 50–300 N forces unilaterally, bilaterally, and anteriorly. The artificial mucosa thickness was 2 mm. Strain gauges were bonded on the vestibular and oral peri-implant sides of each MDI, and on the posterior edentulous area under the ODs. Loadings were performed through the metal plate placed on ODs’ artificial teeth (15 times repeated). Arithmetic means with standard deviations and the significance of the differences (MANOVA, Sheffe post hoc) were calculated. Different MDI numbers, loading positions, forces, and splinting elicited different peri-implant microstrains. In the two-MDI models, 300 N force during unilateral loading elicited the highest microstrains (almost 3000 εμ on the loaded side), which can jeopardize bone reparation. On the opposite side, >2500 εμ was registered, which represents high strains. During bilateral loadings, microstrains hardly exceeded 2000 εμ, indicating that bilateral chewers or subjects having lower forces can benefit from the two Ti-Zr MDIs, irrespective of splinting. However, in subjects chewing unilaterally, and inducing higher forces (natural teeth antagonists), or bruxers, only two MDIs may not be sufficient to support the OD. By increasing implant numbers, peri-implant strains decrease in both splinted and single-unit MDI models, far beyond values that can interfere with bone reparation, indicating that splinting is not necessary. When the positions of the loading forces are closer to the implant, higher peri-implant strains are induced. Regarding the distal edentulous area, microstrains reached 2000 εμ only during unilateral loadings in the two-MDI models, and all other strains were lower, below 1500 εμ, confirming that implant-supported overdentures do not lead to edentulous ridge atrophy. Full article

Background/Objectives: Implant treatment in patients who require teeth extraction due to periodontitis presents a significant challenge. The consideration of peri-implantitis is crucial when planning the placement of dental implants. The predictability of implant treatment relies on the suitability of both hard and soft tissue quality. The aim of this article is to present a case report demonstrating a secure treatment protocol for implant procedures in patients with periodontitis requiring the extraction of all teeth, soft tissue management targeted at increasing the keratinized mucosa zone, and the provision of a reliable prosthetic solution. The secondary objective is to review the relevant literature regarding the significance of keratinized mucosa surrounding dental implants and its association with the occurrence of peri-implantitis. Case presentation: A 65-year-old female with generalized periodontitis, stage IV grade C and very poor oral hygiene came for treatment and rehabilitation of the lower jaw. CBCT revealed periodontal lesions and labio-lingual ridge dimensions in the region of teeth 34–44 from 8.0 to 10.2 mm. The first surgery included teeth extraction and periodontal lesions enucleation with simultaneous placement of four implants in the positions of teeth 32, 34, 42, 44. The second-stage surgery involved increasing the keratinized mucosa using two free gingival grafts. Conclusions: The present case report described the treatment process of the patient with periodontitis, including immediate implantation in the infected region, soft tissue augmentation using free gingival grafts and the ultimate placement of a bar-retained overdenture for final restoration. After two years of observation, despite questionable hygiene, no symptoms of gingival inflammation were detected. Furthermore, there is limited information in the literature regarding the correlation between inadequate keratinized gingiva and the occurrence of peri-implantitis. Full article

Background: The improvement of oral-health-related quality of life (OHRQoL) with different types of prosthesis for completely edentulous jaws in the elderly population is a critical factor in clinical decision making for these vulnerable patients. This review aims to evaluate the changes in OHRQoL after treatment with different types of full-arch prostheses in the elderly edentulous population to determine the prostheses that result in the greatest improvement in OHRQoL. Materials and Methods: Clinical studies of different types of full-arch prostheses that measured the OHRQoL in edentulous patients 60 years or older were searched for in the PubMed, Embase and Scopus electronic databases, with additional hand searching to summarize the outcomes of the selected studies. Result: Among the 302 identified studies, 10 studies were selected. A total of 504 patients wearing 133 complete dentures, 372 implant overdentures and 39 fixed prostheses were assessed among the selected studies. The overall OHIP and GOHAI scores were evaluated at baseline and in the 3rd, 6th, 12th and 18th months of treatment with the respective prostheses. The improved OHRQoL with overall OHIP scores associated with conventional dentures were 9.21–12.5% from the 3rd month to 1 year after treatment, whereas those associated with implant overdentures and full-arch fixed prosthesis were 9–25.26% at 1 year and 18.53–26.79 at the 18th-month follow-up, respectively. The increased overall GOHAI scores were 21.3–25.43% for conventional dentures, 36.82–41.32% for implant overdentures and 39.48–42.83% for full-arch fixed prosthesis from the 3rd month to the 6th-month follow-up. Conclusion: In general, the improvement in OHRQoL after rehabilitation with implant overdentures declined at one year, and that with full-arch fixed prosthesis declined at the 18th-month follow-up; meanwhile, the OHRQoL associated with conventional dentures improved stably up to one year, but the implant-supported prostheses resulted in an obviously greater improvement in the OHRQoL than that obtained with conventional dentures. However, studies with longer follow-up periods are still required to evaluate the long-term clinical effectiveness. Full article

The new Radiological Corticalization Index (CI) is an indicator that describes bone remodeling near the dental implant’s neck at the pixel level and is not visible to the naked eye. The aim of this research was to evaluate the correlation between the CI and bone remodeling using only radiographic (RTG) images. RTG samples were divided into groups depending on prosthetic restoration; the implant neck area around dental implants was examined, and texture features of the RTG images were analyzed. The study also investigated the type of prosthetic restoration and its influence as a factor on bone structure. The statistical analysis included evaluating feature distribution, comparing means (t-test) or medians (W-test), and performing a regression analysis and one-way analysis of variance or the Kruskal–Wallis test, as no normal distribution or between-group variance was indicated for the significant differences in the investigated groups. Differences or relationships were considered statistically significant at p < 0.05. The research revealed correlations between single crowns, overdenture restoration, bridge restoration, platform switching, prosthetic fracture, CI, and also marginal bone loss where p was lower than 0.05. However, the corticalization phenomenon itself has not yet been fully explored. The findings suggest that, depending on the type of prosthetic restoration, the corticalization index may correlate with marginal bone loss or not. Further research is necessary, as the index is suspected to not be homogeneous. Full article

This study presents the first 10-year follow-up investigation of the implant survival and peri-implant outcomes of one-piece mini dental implants (MDIs) retaining mandibular implant overdentures (IODs), including marginal bone level alterations (ΔMBLs), clinical peri-implant parameters, and complications. Twenty participants with horizontally atrophied mandibles received complete dentures and four MDIs (diameter 1.8 mm) at baseline. The dentures were converted into IODs with O-ring attachments. The 10-year follow-up comprised a radiological assessment of ΔMBLs, peri-implant parameters, as well as biological and technical complications. Results from a 10-year follow-up of 14 participants showed a 100% implant survival rate for all 56 implants. The mean ΔMBL after 10 years was −1.12 ± 0.80 mm, with 49 implants classified as successful (ΔMBL < 2 mm) and 7 implants with satisfactory survival (ΔMBL 2–4 mm). Time after implant placement significantly influenced ΔMBL, with stable MBLs after 5 years. The prosthetic survival rate after 10 years was 93%. ΔMBLs were not influenced by implant position or gender but were significantly smaller in subjects older than 65 years. Conclusively, one-piece MDIs with O-ring attachments offer a reliable treatment option for horizontally atrophied mandibles after 10 years, with high implant and prosthetic survival rates, potentially benefiting from advanced age regarding peri-implant bone stability. Full article

Background and Objectives: Despite the identified benefits of early implant loading, studies have questioned its advantages compared to delayed loading in edentulous patients. This study aimed to evaluate clinical peri-implant parameters and marginal bone loss around early placed and loaded mandibular implant overdentures with a 60-month follow-up. Materials and Methods: In this prospective cohort study, 43 patients were enrolled to receive 86 early loading sub-crestal dental implants through prosthetic guides. Implant overdentures were supported by two isolated implant locator attachments between two mental foramens. Clinical peri-implant parameters, including plaque index (PI), bleeding index (BI), peri-implant pocket depth (PIPD), and marginal bone loss (MBL) were evaluated using standardized techniques at 1, 12, 24, 36, 48, and 60 months follow-up. At 60 months, complications associated with implant overdentures (IOD’s) were noted. The mean comparison of peri-implant clinical parameters was performed through ANOVA test. A p-value of ≤0.05 was taken as significant. Results: Out of the total 43 enrolled patients, 8 patients were lost during follow-up; as a result, 35 patients completed the 5 years follow-up. The mean values of PI, BI, and PIPD increased with no statistical difference (p > 0.05). For marginal bone loss, an increase in the mean values was noted at different time intervals with statistical differences (p < 0.001). The most common complications noted were loosening of the abutment, occlusal adjustment, retentive locator loosening and replacement, and relining of the denture. Conclusions: Early placement of IODs failed to prevent bone loss over time and was associated with complications, predominantly consisting of abutment loosening, occlusal adjustments, broken retentive locator components, relining, and rebasing. Full article

Clinical indications for the newly released Ti-Zr (Roxolid^®) alloy mini-implants (MDIs) aimed for overdenture (OD) retention in subjects with narrow alveolar ridges are not fully defined. The aim of this study was to analyze peri-implant and posterior edentulous area microstrains utilizing models of the mandible mimicking a “real” mouth situation with two (splinted with a bar or as single units) or four unsplinted Ti-Zr MDIs. The models were virtually designed from a cone beam computed tomography (CBCT) scan of a convenient patient and printed. The artificial mucosa was two millimeters thick. After MDI insertion, the strain gauges were bonded on the oral and vestibular peri-implant sites, and on distal edentulous areas under a denture. After attaching the ODs to MDIs, the ODs were loaded using a metal plate positioned on the first artificial molars (posterior loadings) bilaterally and unilaterally with 50, 100, and 150 N forces, respectively. During anterior loadings, the plate was positioned on the denture’s incisors and loaded with 50 and 100 N forces. Each loading was repeated 15 times. The means with standard deviations, and the significance of the differences (two- and three-factor MANOVA) were calculated. Variations in the MDI number, location, and splinting status elicited different microstrains. Higher loading forces elicited higher microstrains. Unilateral loadings elicited higher microstrains than bilateral and anterior loadings, especially on the loading side. Peri-implant microstrains were lower in the four-MDI single-unit model than in both two-MDI models (unsplinted and splinted). Posterior implants showed higher peri-implant microstrains than anterior in the four-MDI model. The splinting of the two-MDI did not have a significant effect on peri-implant microstrains but elicited lower microstrains in the posterior edentulous area. The strains did not exceed the bone reparatory mechanisms, although precaution and additional study should be addressed when two Ti-Zr MDIs support mandibular ODs. Full article