Search Results (48)

A non-standardized hypereutectic aluminum–silicon alloy, AlSi18Cu3CrMn, was developed. To refine the structure of the studied composition, a phosphorus modifier was used in an amount of 0.04 wt %, and a complex modifying treatment was applied by combining the chemical elements of phosphorus, titanium, boron and beryllium (P, 0.04 wt %; Ti, 0.2 wt %; B, 0.04 wt %; Be, 0.007 wt %). To improve the mechanical and operational properties of the alloy, it was heat-treated (T6) at a temperature of 510–515 °C before quenching, with artificial aging applied at a temperature of 210 °C for 16 h. Phosphorus-modified alloy AlSi18Cu3CrMn was quenched in water at 20 °C, and the combined modified alloy was quenched in water at temperatures of 20 °C and 50 °C. By conducting a microstructural analysis, the free Si crystals and silicon crystals in the composition of the eutectic in the alloy structure were characterized, and by conducting XRD, the presence and type of secondary phases were established. The hardness of the alloy was measured, as well as the microhardness of the α-solid solution. Static uniaxial tensile testing was carried out at normal and elevated temperatures (working temperatures of 200 °C, 250 °C and 300 °C). By using a gravimetric method, the corrosion rate of the alloy in 1 M NaCl and 1 M H₂SO₄ was calculated. The mass wear, wear intensity and wear resistance of the studied AlSi18Cu3CrMn alloy were determined during reversible reciprocating motion in the boundary-layer lubrication regime. Full article

Secondary hypereutectic Al-Si alloys are attractive for sustainable manufacturing, yet their application is often limited by low strength and electrical conductivity due to impurity-induced microstructural defects. Achieving a balance between mechanical and conductive performance remains a significant challenge. In this work, nickel-coated carbon nanotubes (Ni-CNTs) were introduced into secondary Al-20Si alloys to tailor the microstructure and enhance properties through interfacial engineering. Composites containing 0 to 0.4 wt.% Ni-CNTs were fabricated by conventional casting and systematically characterized. The addition of 0.1 wt.% Ni-CNTs resulted in the best combination of properties, with a tensile strength of 170.13 MPa and electrical conductivity of 27.60% IACS. These improvements stem from refined α-Al dendrites, uniform eutectic Si distribution, and strong interfacial bonding. Strengthening was achieved through grain refinement, Orowan looping, dislocation generation from thermal mismatch, and the formation of reinforcing interfacial phases such as AlNi₃C₀.₉ and Al₄SiC₄. At higher Ni-CNT contents, property degradation occurred due to agglomeration and phase coarsening. This study presents an effective and scalable strategy for achieving strength–conductivity synergy in secondary aluminum alloys via nanoscale interfacial design, offering guidance for the development of multifunctional lightweight materials. Full article

The present study examines the structure, properties and use of complex-alloyed hypereutectic aluminium-silicon alloys, emphasising the control of the morphology of primary silicon via treatment with various modifiers as well as their effects on its shape and distribution. Furthermore, this study reviews the experimental work related to the simultaneous modification of primary and eutectic silicon, which leads to the conclusion that favourable results can be obtained by complex modification treatment involving first- and second-type modifiers. After being cast, the AlSi18Cu3CrMn and AlSi18Cu5Mg non-standardised piston alloys are subjected to T6 heat treatment intended to enhance their mechanical performance, harnessing the full potential of the alloying elements. A microstructural analysis of the shape and distribution of both primary and eutectic silicon crystals following heat treatment was employed to determine their microhardness. Full article

Hypereutectic Al-Si alloys containing primary Si exhibit unique material properties that make them suitable for various industrial applications. Understanding the characteristics of primary Si is crucial for predicting the effect of solidification conditions on the microstructure of these alloys. This paper presents a comprehensive characterisation study of primary Si in hypereutectic alloys. This study provides a detailed analysis of the size, distribution, and morphology of primary Si, providing valuable insights into the alloy structure, mechanical properties, and even the performance of the production process. The effect of forced melt flow by a rotating magnetic field (RMF) and solid/liquid front velocity on the size and morphology of primary Si in a hypereutectic Al-18 wt.% Si alloy was investigated. The purpose of using the RMF technique during the solidification process of Al-Si alloys is to enhance the alloy’s microstructure by inducing electromagnetic stirring. The hypereutectic samples were solidified at five different front velocities (0.02, 0.04, 0.08, 0.2, and 0.4 mm/s), under an average temperature gradient (G) of 8 K/mm, in a crystalliser equipped with an RMF inductor. Each sample was divided into two parts: the first solidified without stirring, while the second underwent electromagnetic stirring using RMF at an induction (B) of 7.2 mT. The results revealed that increasing the front velocity during solidification refined the primary Si in stirred and non-stirred parts. In non-stirred parts, it decreased dendritic forms and increased star-like Si, while polyhedral shapes remained nearly constant. Stirred parts showed stable Si morphology across velocities. Higher velocities also promoted equiaxed over elongated Si forms in both parts. Full article

The microstructure of hypereutectic Al-Si alloys is crucial in determining their mechanical properties and overall performance in engineering applications. This paper investigates the effect of a rotating magnetic field (RMF) and eutectic front velocity on the microstructure of hypereutectic Al-18 wt.% Si alloy. The hypereutectic samples were solidified using five different front velocities (0.02, 0.05, 0.09, 0.2, and 0.4 mm/s) with an average temperature gradient (G) of 8 K/mm in a crystallizer equipped with an RMF inductor. The samples were solidified into two sections. The first section solidified without stirring, while the second section solidified with stirring using RMF at an induction (B) of 7.2 mT. The length, angular orientation of eutectic Si lamellas, and interlamellar distances were measured in both the non-stirred and the stirred sections to evaluate the impact of RMF and front velocity on the eutectic structure. The results revealed that the application of RMF and the increase in front velocity during solidification led to the significant refinement of the eutectic structure. These findings highlight the potential of RMF and front velocity manipulation to enhance the microstructure of hypereutectic Al-Si alloys, with practical implications for the development of high-performance materials. Full article

The research presents a novel approach to develop high-strength functionally graded composite materials (FGCMs) by using recycled coconut shell ash (CSA) particles as reinforcement for a hypereutectic Al-Si alloy matrix. Using a centrifugal casting technique, test specimens are prepared for the study under ASTM standards. The optimal combination of materials to maximise the materials’ overall tensile strength is obtained through the mixture methodology approach. The results show that CSA particles in the matrix material increase the tensile strength of the produced material. Process parameters, melting temperature and rotating speed were found to play a pivotal role in determining the tensile strength. A better tensile strength of the material is obtained when Al-Si = 90.5 wt%, CSA = 9.5 wt%, rotating speed = 800 RPM, and melting temperature = 800 °C; the proposed regression model developed has substantial predictability for tensile strength. This work presents a methodology for enhancing the tensile strength of FGCMs by optimising both the material composition and processing parameters. The achieved tensile strength of 197.4 MPa, at 800 RPM and 800 °C, for a concentration of 7.5 wt% CSA particles, makes these FGCMs suitable for use in multiple engineering sectors. Full article

Sulfuric acid anodizing assisted by a hydrothermal sealing with inhibitors [Ce³⁺-Mo⁶⁺] was used to prevent pitting corrosion on spray-deposited hypereutectic Al–Si alloy (A390). An investigation concerning the evaluation of pitting corrosion resistance on the anodic oxide thin film with ions incorporated was carried out in NaCl solution using electrochemical measurements (i.e., potentiodynamic polarization and electrochemical impedance spectroscopy, EIS). The influence of Si phase morphology and size on the growth mechanism of an anodic oxide film was characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The results were then compared with those for its equivalent IM390 alloy (Al-17Si-4.5Cu-0.6Mg) produced through a conventional process ingot metallurgy, IM. The electrochemical findings indicate that sulfuric acid anodizing followed by a simple hot water sealing treatment was ineffective. In this manner, an intense attack was localized by pitting corrosion that occurred on the anodic oxide film in less than three days, as denoted by characteristic changes in the EIS spectra at the lowest frequencies. Improved results were achieved for Ce–Mo surface modification, which can provide better corrosion resistance on the aluminum alloys because no signs of pits were observed during the corrosion testing. Full article

With the ever-growing emphasis on global decarbonization and rapid increases in the power densities of electronics equipment in recent years, new methods and lightweight materials have been developed to manage heat load as well as interfacial stresses associated with coefficient of thermal expansion (CTE) mismatches between components. The Al–Si system provides an attractive combination of CTE performance and high thermal conductivity whilst being a very lightweight option. Such materials are of interest to industries where thermal management is a key design criterion, such as the aerospace, automotive, consumer electronics, defense, EV, and space sectors. This paper will describe the development and manufacture of a family of high-performance hypereutectic Al–Si alloys (AyontEX™) by a powder metallurgy method. These alloys are of particular interest for structural heat sink applications that require high reliability under thermal cycling (CTE of 17 μm/(m·°C)), as well as reflective optics and instrument assemblies that require good thermal and mechanical stability (CTE of 13 μm/(m·°C)). Critical performance relationships are presented, coupled with the microstructural, physical, and mechanical properties of these Al–Si alloys. Full article

The crystallography of the eutectic Al-Si microstructure in both unmodified and Sr (0.2 wt.%)-modified hypereutectic Al-20 wt.% Si alloys, processed via arc-melting and laser surface remelting, has been comprehensively characterized using transmission electron microscopy and electron diffraction. Although, under as-cast conditions, specific orientations between different planes of Al and Si, satisfying defined orientation relationships (ORs), have been investigated within the flake morphology, the rapid solidification induced by laser surface remelting results in a notable transformation from a flake morphology to nanocrystalline Si fibers dispersed in an Al matrix. Consequently, this transformation results in a mis-orientation of the interface between the eutectic Al and Si phases, preventing the formation of orientation relationships, thus promoting the formation of faceted interfaces exhibiting substantial lattice disregistry. Full article

The objective of the current work is to establish, on the one hand, the conventional mechanisms of grain refining and, on the other hand, the effect of the refining-modification interaction in Sr-modified Al-Si alloys on the achieved grain refining and the modification of eutectic silicon. For this purpose, the hypereutectic alloy A390.1 (~17%Si) was used. Various grain refiners were used, namely, Al-10%Ti, Al-5%Ti-1%B, and Al-4%B. After the preparation of the liquid metal, several concentrations of these master alloys were added to the liquid bath according to the desired objective. The different melts prepared were heated at 750 °C and cast in a preheated graphite mold with a solidification rate of around 0.8 °C/s. The liquid metal was. The presence of strontium (added in the form of Al-10%Sr master alloy) and boron completely affects the microstructure of the alloy. An atom of Sr unites with 6 atoms of B to form a compound whose stoichiometric formula is of the SrB₆ type, leading to a significant reduction in the modification. A strong relationship exists between the addition of B and the recovery level of Sr. The affinity between titanium and boron is stronger than the affinity between boron and strontium. Both B and TiB₂ phase particles do not react with Si; it is only the Ti part of the Al-Ti-B master that forms (Al, Si)₃Ti. Regardless of the amount of Si content in the alloy, the Al-4%B master alloy achieves the best grain refining compared to Ti-containing master alloys. Full article

Hypereutectic Al-Si alloys, which have a silicon content ranging from 12% to 70%, are a new generation of casing materials for chip packaging. They have broad applications in aerospace, weaponry, and civilian communications. Selective Laser Melting (SLM) offers significant advantages in achieving near-net shaping of complex casings. This paper presents a study on the formation defects, microstructure, and room temperature tensile properties of AlSi60 alloy prepared by SLM. The results indicate that the primary forming defects in the SLM AlSi60 alloy are balling, lack of fusion, and porosity. These defects are mainly influenced by the volumetric energy density. Samples of good quality can be produced within the range of 150 J/mm³ to 250 J/mm³. However, the same volumetric energy density can result in differences in sample quality due to various combinations of process parameters. Therefore, it has been determined that a well-formed AlSi60 alloy can be obtained within a laser power range of 300 W–350 W, scanning speed of 400 mm/s–800 mm/s, and hatch spacing of 0.09 mm–0.13 mm, with a density close to 98%. The microstructure of the SLM AlSi60 alloy consists of primary Si phases with irregular shapes and sharp edges measuring 5–10 μm, eutectic Si particles of 0.5 μm, and α-Al phases, with eutectic Si dispersed within the α-Al. The SLM AlSi60 alloy exhibits fine and evenly distributed primary Si phases with an average hardness of 203 HV. No significant anisotropy in hardness values was observed in the X and Y directions. The tensile strength of the alloy reached an average of 219 MPa, with an average elongation of 2.99%. During the tensile process, cracks initiated by the primary Si phases rapidly expanded, exhibiting minor ductile fracture characteristics in the Al phases. Due to the high volume fraction of Si phases, the tensile test was dominated by brittle fracture. The tensile curve only exhibited the elastic stage. Full article

An optimisation model for small datasets was applied to thixocasted/compocasted composites and hybrid composites with hypereutectic Al-18Si base alloys. Composites were produced with the addition of Al₂O₃ (36 µm/25 nm) or SiC (40 µm) particles. Based on the design of experiment, tribological tests were performed on the tribometer with block-on-disc contact geometry for normal loads of 100 and 200 N, a sliding speed of 0.5 m/s, and a sliding distance of 1000 m. For the prediction of the tribological behaviour of composites, artificial neural networks (ANNs) were used. Three inputs were considered for ANN training: type of reinforcement (base alloy, Al₂O₃ and SiC), amount of Al₂O₃ nano-reinforcement (0 and 0.5 wt.%), and load (100 and 200 N). Various ANNs were applied, and the best ANN for wear rate (WR), with an overall regression coefficient of 0.99484, was a network with architecture 3-15-1 and a logsig (logarithmic sigmoid) transfer function. For coefficient of friction (CoF), the best ANN was the one with architecture 3-6-1 and a tansig (hyperbolic tangent sigmoid) transfer function and had an overall regression coefficient of 0.93096. To investigate the potential of ANN for the prediction of two outputs simultaneously, an ANN was trained, and the best results were from network 3-5-2 with a logsig transfer function and overall regression coefficient of 0.99776, but the predicted values for CoF in this case did not show good correlation with experimental results. After the selection of the best ANNs, the Taguchi grey multi-response optimisation of WR and CoF was performed for the same combination of factors as the ANNs. For optimal WR and CoF, the combination of factors was as follows: composite with 3 wt.% Al₂O₃ micro-reinforcement, 0.5 wt.% Al₂O₃ nano-reinforcement, and a load of 100 N. The results show that developed ANN, the Taguchi method, and the Taguchi grey method can, with high reliability, be used for the optimisation of wear rate and coefficient of friction of hypereutectic Al-Si composites. Microstructural investigations of worn surfaces were performed, and the wear mechanism for all tested materials was light abrasion and adhesion. The findings from this research can contribute to the future development of hypereutectic Al-Si composites. Full article

In this study, the effects of friction stir processing (FSP) parameters on the microstructure and hardness of cast Al-Si-Fe-Mg alloy were investigated. Orthogonal arrays were applied in the design of the experiments. The selected parameters for the experiments included rotation speed, transverse speed, penetration depth, and tilt angle. The microstructure and hardness of the FSPed Al-Si-Fe-Mg were studied using optical and scanning electron microscopy, and microhardness testing, respectively. The quadratic model was proposed to fit the experimental data of hardness. Signal-to-noise ratio (S/N) analysis showed the maximum hardness achieved when rotation speed, transverse speed, penetration depth, and tilt angle were chosen as 1600 rpm, 400 mm/min, 0.1 mm, and 1.5°, respectively. Taguchi’s analysis of variance (ANOVA) was used to determine the significant FSP parameters on hardness, which revealed that rotation speed was the most dominant processing parameter, followed by transverse speed, tilt angle, and penetration depth. Moreover, a quadratic polynomial model was developed to predict and optimize the combination of the parameters, enabling superior mechanical properties. Subsequently, the verification of the microstructure was conducted, demonstrating good agreement between the experimental observation of the microstructure and estimated outcomes. Full article

Rapid solidification techniques, such as gas atomisation, have been widely implemented in metallic alloys/composites to increase solid solubility, avoid or mitigate segregation phenomena, and favour metastable phase formation to enhance performance. Particularly, gas atomisation can enhance the solid solubility of low diffusion coefficient elements like Fe, Ni, Mn, Zr, and Cr in the α-Al matrix, yielding metastable phases. As a result, Al alloys exhibit excellent strength at high temperatures. In this study, the AISI 304L alloy was employed to introduce Fe, Ni, and Cr elements into the AlSi10Mg alloy through gas atomisation, resulting in the formation of two distinct hypereutectic AlFe-based alloys: AlFe9Si8Cr2Ni and AlFe18Si8Cr5Ni2. Gas-atomised alloy powders were separated into different size fractions by sieving and characterised using X-ray diffraction, differential scanning calorimetry, optical microscopy, and scanning electron microscopy. Microstructural analyses revealed dendritic patterns with distinct phases, highlighting the influence of the alloying element content on the solidification processes. Furthermore, a synergic evaluation of the XRD and EDS analysis results allowed the identification of intermetallic phases and their distribution in the two systems. Full article

The synergistic effect between strontium (Sr) and melt quenching on the solidified microstructure of hypereutectic Al-Si alloys was investigated by optical and scanning electron microscopy. The results indicate that melt quenching can suppress the growth of primary Si particles in the solidified structure of the hypereutectic Al-Si alloy, resulting in a significant decrease of in the average size of primary Si particles in Al-(18~22)Si alloys from 30.35~66.31 μm to 15.13~34.63 μm. The synergistic effect between Sr and melt quenching can further inhibit the precipitation of primary Si particles in the Al-18Si alloy. After the addition of Sr to Al-18Si alloy and undergoing melt quenching, the area fraction of primary Si clearly decreases. When the added amount of Sr increases from 0.1 wt.% to 0.5 wt.%, the area fraction of primary Si decreases from 1.13% to 0.16%. With 0.5 wt.% Sr in the tested alloy, the inhibiting effect on primary Si precipitation was significantly improved. Research has shown that the cooling rate has a significant impact on the solidified structure of the melt-quenched Al-18Si-0.5Sr alloy. There exists no primary Si in solidified structures on the area of 1/8R and 1/4R from the surface of the round bar sample, but the area fraction of primary Si increases, respectively, to 1.97% and 12.48% on the area of 1/2R and R from the surface. The higher the cooling rate, the higher the inhibitory effect on the primary Si precipitation in the Al-18Si-0.5Sr alloy. Full article