Search Results (780)

This study investigates the strengthening mechanisms of char in silicon dioxide thermal reduction through systematic high-temperature experiments using three char types (YQ1, CW1, HY1) characterized by X-ray diffraction, Raman spectroscopy, transmission electron microscopy, and scanning electron microscopy. HY1 char demonstrated superior reactivity due to its highly ordered microcrystalline structure, characterized by the largest aromatic cluster size (L_a) and lowest defect ratio (I_D/I_G = 0.37), which directly correlated with enhanced reaction completeness. The carbon–silicon reaction reactivity increased progressively with temperature, achieving optimal performance at 1550 °C. Addition of Fe and Fe₂O₃ significantly accelerated the reduction process, with Fe₂O₃ exhibiting superior catalytic performance by reducing activation energy and optimizing reaction kinetics. The ferrosilicon formation mechanism proceeds through a two-stage pathway: initial char-SiO₂ reaction producing SiC and CO, followed by SiC–iron interaction generating FeSi, which catalytically promotes further reduction. These findings establish critical structure–performance relationships for char selection in industrial silicon production, where microcrystalline ordering emerges as the primary performance determinant. The identification of optimal temperature and additive conditions provides practical pathways to enhance energy efficiency and product quality in silicon metallurgy, enabling informed raw material selection and process optimization to reduce energy consumption and improve operational stability. Full article

The catalytic decomposition of CH₄ is a promising method for producing high-purity CO_x-free hydrogen. A Ni-Al-LDH catalyst synthesized via coprecipitation was modified with alkali metals (Mg, La, Ca, or Li) through reconstruction to enhance catalytic activity and resistance to deactivation during catalytic methane decomposition (CMD). The catalysts were evaluated by two activation methods: H₂ reduction and direct heating with CH₄. The MgNA-R catalyst achieved the highest CH₄ conversion (65%) at 600 °C when reduced with H₂, attributed to a stronger Ni-Al interaction. Under CH₄ activation, LaNA-C achieved a 55% conversion at the same temperature, associated with a smaller crystallite size and higher reducibility due to La incorporation. Although all catalysts deactivated due to carbon deposition and/or sintering, LaNA-C was the only sample that could resist deactivation for a longer period, as La appears to have a protective effect on the active phase. Post-reaction characterizations revealed the formation of graphitic and filamentous carbon. Raman spectroscopy exhibited a higher degree of graphitization and structural order in LaNA-C, whereas SEM showed a more uniform distribution of carbon filaments. TEM confirmed the presence of multi-walled carbon nanotubes with encapsulated Ni particles in La-promoted samples. These results demonstrate that La addition improves the catalytic performance under CH₄ activation and carbon structure. This finding offers a practical advantage for CMD processes, as it reduces or eliminates the need to use hydrogen during catalyst activation. Full article

The stabilization of heavy metal elements, such as zinc, in the form of ions within the glass-ceramics represents a valuable approach to addressing environmental pollution caused by heavy metals. This study investigates the feasibility and physicochemical properties of diopside-based glass-ceramics synthesized from zinc-containing smelting slag. The zinc-rich smelting slag is abundant in SiO₂, Al₂O₃, CaO, and other constituents, thereby providing cost-effective and efficient raw materials for glass-ceramic production. The conversion of zinc-containing smelting slag into glass-ceramics was achieved through a melting process. We analyzed the effects of varying doping levels on the properties of the resulting glass-ceramics. The results indicated that as the doping level of smelting slag increases, the crystallization temperature of the glass-ceramics decreases while the crystal phases of diopside and anorthite progressively increase, significantly enhancing both mechanical strength and chemical stability. Notably, when the doping level reaches 60%, these glass-ceramics exhibit remarkable physical properties, including high density (3.12 g/cm³), Vickers hardness (16.60 GPa), and excellent flexural strength (150.75 MPa). Furthermore, with increasing amounts of doped smelting slag, there are substantial improvements in acid resistance, alkali resistance, and corrosion resistance in these materials. Raman spectroscopy and EDS analysis further verified a uniform distribution of the crystal phase and effective immobilization of heavy metal zinc. Full article

An anion exchange-assisted technique was used for the synthesis of platinum-decorated SnO₂ supports, providing nanocatalysts with enhanced activity for the reduction of 4-nitrophenol (4-NP) to 4-aminophenol (4-AP). In this study, a series of SnO₂ supports, namely SnA (synthesized almost at room temperature), SnB (hydrothermally treated at 180 °C), and SnC (annealed at 600 °C), are systematically investigated, all loaded with 1 mol% Pt from H₂PtCl₆ under identical mild conditions. The chloride ions from the SnCl₄ precursors were efficiently removed via a strong-base anion exchange reaction, resulting in highly dispersed, crystalline ~5 nm cassiterite SnO₂ particles. All Pt/SnO₂ composites displayed mesoporous structures with type IVa isotherms and H₂-type hysteresis, with SP1a (Pt on SnA) exhibiting the largest surface area (122.6 m²/g) and the smallest pores (~3.5 nm). STEM-HAADF imaging revealed well-dispersed PtOx domains (~0.85 nm), while XPS confirmed the dominant Pt⁴⁺ and Pt²⁺ species, with ~25% Pt⁰ likely resulting from photoreduction and/or interactions with Sn–OH surface groups. Raman spectroscopy revealed three new bands (260–360 cm⁻¹) that were clearly visible in the sample with 10 mol% Pt and were due to the vibrational modes of the PtOx species and Pt-Cl bonds introduced due the addition and hydrolysis of H₂PtCl₆ precursor. TGA/DSC analysis revealed the highest mass loss for SP1a (~7.3%), confirming the strong hydration of the PtOx domains. Despite the predominance of oxidized PtOx species, SP1a exhibited the highest catalytic activity (k_app = 1.27 × 10⁻² s⁻¹) and retained 84.5% activity for the reduction of 4-NP to 4-AP after 10 cycles. This chloride-free low-temperature synthesis route offers a promising and generalizable strategy for the preparation of noble metal-based nanocatalysts on oxide supports with high catalytic activity and reusability. Full article

Ultra-fine-grained bainitic (UFGB) steels offer excellent mechanical properties, which can be further improved by applying diamond-like carbon (DLC) coatings. However, poor adhesion between the coating and substrate remains a key limitation. Since the steel’s microstructure degrades at high temperatures, enhancing adhesion without heating the substrate is essential. This study investigates surface hardening combined with simultaneous nitrogen and hydrogen doping during the Radio Frequency Chemical Vapor Deposition (RFCVD) process to improve coating performance. Varying gas compositions were tested to assess their effects on coating properties. Nitrogen incorporation decreased hardness from 12 GPa to 9 GPa but improved adhesion, while hydrogen limited damage after coating failure. Optimizing the gas mixture led to enhanced adhesion and wear resistance. Raman and X-ray photoelectron spectroscopy (XPS) analyses confirmed that the optimized coatings had the highest sp³ bond content and elevated nitrogen levels. While both hardness and adhesion contributed to wear resistance, no direct link to coating thickness was found. Overall, co-doping with nitrogen and hydrogen is an effective approach to improve adhesion and wear resistance without requiring high processing temperatures or complex equipment. Full article

After reviewing the state of the art of the fluorination of inorganic solid electrolytes, an application of gas/solid fluorination is given and how it can be processed. Garnet-type oxide has been chosen. These oxides with an ideal structure of chemical formula A₃B₂(XO₄)₃ are mainly known for their magnetic and dielectric properties. Certain garnets may have a high enough Li⁺ ionic conductivity to be used as solid electrolyte of lithium ion battery. The surface of LLZO may be changed in contact with the moisture and CO₂ present in the atmosphere that results in a change of the conductivity at the interface of the solid. LiOH and/or lithium carbonate are formed at the surface of the garnet particles. In order to allow for handling and storage under normal conditions of this solid electrolyte, surface fluorination was performed using elemental fluorine. When controlled using mild conditions (temperature lower or equal to 200 °C, either in static or dynamic mode), the addition of fluorine atoms to LLZO with Li_6,4Al_0,2La₃Zr₂O₁₂ composition is limited to the surface, forming a covering layer of lithium fluoride LiF. The effect of the fluorination was evidenced by IR, Raman, and NMR spectroscopies. If present in the pristine LLZO powder, then the carbonate groups disappear. More interestingly, contrary to the pristine LLZO, the contents of these groups are drastically reduced even after storage in air up to 45 days when the powder is covered with the LiF layer. Surface fluorination could be applied to other solid electrolytes that are air sensitive. Full article

In this study, we introduce a high-resolution, high-speed thermal imaging technique using Raman spectroscopy to simultaneously measure the temperature of a substrate and a channel. By modifying the Raman spectrometer, we achieved a measurement speed faster than commercial spectrometers. This system demonstrated a sub-micron spatial resolution and the ability to measure the temperatures of the Si substrate and GaN channel simultaneously. During high-current operation, we observed significant self-heating in the GaN channel, with hotspots 100 °C higher than the surroundings, while the Si substrate showed an even temperature distribution. The ability to detect hotspots can help secure the reliability of devices through early failure analysis and can also be used for improvement research to reduce hotspots. These findings highlight the potential of this technique for early defect inspection and device improvement research. This study provides a novel and effective method for measuring the sub-micron resolution temperature distribution in devices, which can be applied to various semiconductor devices, including SiC-based power devices. Full article

This study aims to investigate the influence of various metal compounds (ZnO, ZnCl₂, Zn(OH)₂, MgO, MgCl₂, and Mg(OH)₂) on the structural and electrochemical properties of chars derived from the pyrolysis of polyvinyl chloride (PVC). Raw PVC samples mixed with different metal compounds were firstly pyrolyzed at 500 °C in a fixed-bed reactor. The produced chars were further pyrolyzed at 800 °C. The objective was to evaluate the impact of these metal compounds on the char structure through comparative analysis. The pyrolytic chars were characterized using Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Raman spectroscopy, and Brunauer–Emmett–Teller (BET) analysis. Zinc-based additives notably increased carbon yield to 32–34 wt.%, attributed to ZnCl₂-induced cross-linking. Specifically, ZnO facilitated porous architectures and aromatic structures with six or more rings. Mg-based compounds induce the formation of a highly stacked carbon structure primarily composed of crosslinked cyclic alkenes, rather than large polyaromatic domains. Upon further thermal treatment, these aliphatic-rich stacked structures can be progressively transformed into aromatic frameworks through dehydrogenation reactions at elevated temperatures. A high-surface-area porous carbon material (PVC/ZnO-800, SSA = 609.382 m² g⁻¹) was synthesized, demonstrating a specific capacitance of 306 F g⁻¹ at 1 A g⁻¹ current density. Full article

Complex antimony pyrochlores Bi_2.7M_0.46Ni_0.70Sb₂O_10+Δ (M = Zn, Mg) were synthesized from oxide precursors, using the solid-state reaction method. For each composition variant, the pyrochlore phase formation process was studied during solid-state synthesis in the range of 500–1050 °C. The influence of zinc and magnesium on the phase formation process was established. The interaction of oxide precursors occurs at a temperature of 600 °C and higher, resulting in the formation of bismuth stibate (Bi₃SbO₇) as a binary impurity phase. Oxide precursors, including bismuth(III) and antimony(III,V) oxides, are fixed in the samples up to 750 °C, at which point the intermediate cubic phase Bi₃M_2/3Sb_7/3O₁₁ (sp. gr. Pn-3, M = Zn, Ni) is formed in the zinc system. Interacting with transition element oxides, it is transformed into pyrochlore. An intermediate phase with the Bi_4.66Ca_1.09VO_10.5 structure (sp. gr. Pnnm) was found in the magnesium system. The unit cell parameter of pyrochlore for two samples has a minimum value at 800 °C, which is associated with the onset of high-temperature synthesis of pyrochlore. The synthesis of phase-pure pyrochlores is confirmed by high-resolution Raman spectroscopy. The data interpretation showed that the cations in Ni/Zn pyrochlore are more likely to be incorporated into bismuth positions than in Ni/Mg pyrochlore. The nickel–magnesium pyrochlore is characterized by a low-porosity microstructure, with grain sizes of up to 3 μm, according to SEM data. Zinc oxide has a sintering effect on ceramics. Therefore, the grain size in ceramics is large and varies from 2 to 7 μm. Full article

Activated carbon prepared from coconut shell was characterized using SEM/EDS, N₂-sorption, XRD analysis, Raman, and FTIR spectroscopy. It was then evaluated in terms of its capacity to adsorb nitrobenzene, a priority pollutant, from water samples with varying pH levels. Initial studies revealed high adsorption capacity; further studies were broadened to include nitrobenzene derivative, dinitrobenzene, as real samples are expected to contain a mixture of these pollutants. The maximum amount of adsorbed adsorbate increased notably with temperature, reaching 12.88 mg g⁻¹ and 42.75 mg g⁻¹ for nitrobenzene and dinitrobenzene, respectively, at 35 °C. Thermodynamic considerations and determined values of ∆G⁰ and ∆S⁰ indicated that the adsorption process of both nitrobenzene and dinitrobenzene is spontaneous and ∆H⁰ value indicated that it is endothermic in the studied temperature range. A study of the simultaneous adsorption of nitrobenzene and dinitrobenzene indicated a higher affinity toward dinitrobenzene. This study pointed out that coconut shell-derived activated carbon holds high potential as an adsorbent for removing nitrobenzene and its derivatives from water samples. Full article

To address the challenge of ultra-deep desulfurization in fuels, a series of heteropolyacid-based poly(ionic liquid) catalysts (C4-PIL@PW, C8-PIL@PW, and C16-PIL@PW) were synthesized via radical polymerization and anion exchange methods. The prepared catalysts were characterized via FT-IR, XRD pattern, and Raman spectroscopy. Optimal reaction parameters (e.g., temperature, catalyst dosage, and O/S molar ratio) were systematically investigated, as well as the catalytic mechanism. The typical sample C8-PIL@PW exhibited exceptional oxidative desulfurization (ODS) performance, achieving a sulfur removal of 99.2% for dibenzothiophene (DBT) without any organic solvent as extractant. Remarkably, the sulfur removal could still retain 89% after recycling five times without regeneration. This study provides a sustainable and high-efficiency catalyst for ODS, offering insights into fuel purification strategies. Full article

In this study, graphene production via liquid-phase exfoliation assisted by sonication was evaluated using deionized water as a solvent and two graphite sources: one recovered from spent lithium-ion batteries (LIBs) and a commercial counterpart. A 750 W, 20 kHz ultrasonic processor was used, with sonication amplitudes ranging from 50% to 80% for two hours while maintaining a constant temperature of 45 °C. The resulting dispersions were left undisturbed for 24 h at ambient temperature to allow natural phase separation between decanted and dispersed fractions. These fractions were subsequently dried and weighed to determine exfoliation yield. High-quality graphene was successfully obtained via direct liquid-phase exfoliation of graphite recovered from LIBs, assisted by sonication in deionized water. Graphene formation was confirmed in both suspended and decanted fractions after two hours of sonication at 80% amplitude through complementary characterization techniques, including UV-Vis, Raman spectroscopy, HRTEM, and XRD. Comparative experiments using thermally pretreated battery graphite and commercial graphite revealed that graphene dispersions derived from untreated LIB-derived graphite exhibited greater long-term stability than those obtained from commercial or thermally pretreated battery graphite before sonication. Full article

Local temperature measurement is crucial for understanding nanoscale thermal transport and developing nanodevices for biomedical, photonic, and optoelectronic applications. The rise of photothermal therapy for cancer treatment has increased the demand for high-resolution nanothermometric techniques capable of non-contact intracellular temperature measurement and modification. Raman spectroscopy meets this need: the ratio of anti-Stokes to Stokes Raman intensities for a specific vibrational mode correlates with local temperature through the Boltzmann distribution. The present study proposes a novel photothermal therapy agent designed to advance the current state of the art while adhering to green chemistry principles, thereby favoring low-temperature synthesis involving limited energy consumption. A key challenge in this field is to achieve close contact between plasmonic nanosystems, which act as nanoheaters, and local temperature sensors. This is achieved by employing silver nanoparticles as a heat release agent, coated with anatase-phase titanium dioxide, as a local temperature sensor. The proposed synthesis, which combines refluxing and subcritical solvothermal treatments, enables direct anatase formation, despite its metastability under standard conditions, thus eliminating the need for a calcination step. Structural characterization through SAED-HRTEM and Raman spectroscopy confirms the successful crystallization of the desired phase. Moreover, the nanothermometry measurements conducted at various wavelengths ultimately demonstrate both the effectiveness of these nanomaterials as thermometric probes, with a relative sensitivity of about 0.24 K⁻¹%, and their capability as local heaters, with a release of a few tens of degrees. This work demonstrates a new synthetic strategy for these nanocomposites, which offers a promising pathway for the optimization of nanosystems in therapeutic applications. Full article

Camellia oil, rich in monounsaturated fatty acids, squalene, tocopherols, and polyphenols, is highly valued for its nutritional benefits. However, its high market value and regional variations have led to frequent adulteration, highlighting the need for rapid, non-destructive methods for authentication, geographical traceability, and quality assessment. This study employed portable Raman spectroscopy combined with Partial Least Squares Discriminant Analysis (PLS-DA) and Multivariate Curve Resolution–Alternating Least Squares (MCR-ALS) to differentiate camellia oil from other edible oils and evaluate its thermal and photo-oxidative stability. PLS-DA, based on VIP-selected spectral variables, effectively distinguished camellia oil, with Raman bands near 1250 cm⁻¹ and 1650 cm⁻¹ contributing significantly. A unique peak at 1525 cm⁻¹, observed in samples from Gongcheng, Guangxi, was associated with carotenoids and served as a potential marker for geographical traceability. MCR-ALS modeling revealed significant reductions in the 1650 cm⁻¹ and 1525 cm⁻¹ peaks when temperatures exceeded 150 °C, indicating degradation of unsaturated fatty acids and carotenoids. Under UV exposure, the 1525 cm⁻¹ peak declined sharply and nearly disappeared after 24 h, suggesting rapid carotenoid degradation via photooxidation. Extended UV treatment also affected the 1650 cm⁻¹ peak and led to oxidative product accumulation. Overall, this study demonstrates the feasibility of integrating Raman spectroscopy with chemometric analysis for efficient oil classification, traceability, and stability monitoring, offering a valuable tool for food quality control and market supervision. Full article

This study investigates a novel approach to moderate-temperature carbon capture by examining the enhanced performance of thermally pre-treated dolomite. To obtain mixed oxides, dolomite samples were prepared via calcination in a quartz cylindrical furnace under an ambient atmosphere at 900 °C, and subsequently thermally pre-treated under an inert (argon) stream at 650 °C. Characterization of the as-prepared samples involved morphological, structural, textural, and optical features examined through XRD, BET, SEM-EDS, FT-IR, and RAMAN, XPS, and UV-vis spectroscopy, whereas TGA and subsequent multicyclic tests were used to study the CO₂ sorption. The dolomite sample calcined at 900 °C for 60 min, and after being activated under an inert atmosphere (argon), labeled PCD60Act, exhibited the highest CO₂ uptake of 0.477 g_CO2/g_sorbent; after 15 sorption–regeneration cycles, it still retained a CO₂ uptake of 0.38 g_CO2/g_sorbent at 650 °C, and it was also successfully regenerated at this moderate temperature, demonstrating 84% capture capacity retention. These remarkable results are explained by the crystalline defects generated during the thermal pre-treatments of the dolomite. This research offers valuable perspectives on the viability of employing thermally pre-treated dolomite as an inexpensive, thermally stable, and moderate-temperature regenerable CaO-based sorbent for applications in CO₂ removal in the context of integrated carbon capture and conversion (ICCC) for the production of high-purity hydrogen. Full article